forked from Minki/linux
[POWERPC] Device tree bindings for Xilinx devices
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This commit is contained in:
Grant Likely
Josh Boyer
parent
d474037334
commit
7ae0fa49c6
@ -52,6 +52,7 @@ Table of Contents
|
||||
i) Freescale QUICC Engine module (QE)
|
||||
j) CFI or JEDEC memory-mapped NOR flash
|
||||
k) Global Utilities Block
|
||||
l) Xilinx IP cores
|
||||
|
||||
VII - Specifying interrupt information for devices
|
||||
1) interrupts property
|
||||
@ -2242,6 +2243,266 @@ platforms are moved over to use the flattened-device-tree model.
|
||||
available.
|
||||
For Axon: 0x0000012a
|
||||
|
||||
l) Xilinx IP cores
|
||||
|
||||
The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
|
||||
in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range
|
||||
of standard device types (network, serial, etc.) and miscellanious
|
||||
devices (gpio, LCD, spi, etc). Also, since these devices are
|
||||
implemented within the fpga fabric every instance of the device can be
|
||||
synthesised with different options that change the behaviour.
|
||||
|
||||
Each IP-core has a set of parameters which the FPGA designer can use to
|
||||
control how the core is synthesized. Historically, the EDK tool would
|
||||
extract the device parameters relevant to device drivers and copy them
|
||||
into an 'xparameters.h' in the form of #define symbols. This tells the
|
||||
device drivers how the IP cores are configured, but it requres the kernel
|
||||
to be recompiled every time the FPGA bitstream is resynthesized.
|
||||
|
||||
The new approach is to export the parameters into the device tree and
|
||||
generate a new device tree each time the FPGA bitstream changes. The
|
||||
parameters which used to be exported as #defines will now become
|
||||
properties of the device node. In general, device nodes for IP-cores
|
||||
will take the following form:
|
||||
|
||||
(name)@(base-address) {
|
||||
compatible = "xlnx,(ip-core-name)-(HW_VER)"
|
||||
[, (list of compatible devices), ...];
|
||||
reg = <(baseaddr) (size)>;
|
||||
interrupt-parent = <&interrupt-controller-phandle>;
|
||||
interrupts = < ... >;
|
||||
xlnx,(parameter1) = "(string-value)";
|
||||
xlnx,(parameter2) = <(int-value)>;
|
||||
};
|
||||
|
||||
(ip-core-name): the name of the ip block (given after the BEGIN
|
||||
directive in system.mhs). Should be in lowercase
|
||||
and all underscores '_' converted to dashes '-'.
|
||||
(name): is derived from the "PARAMETER INSTANCE" value.
|
||||
(parameter#): C_* parameters from system.mhs. The C_ prefix is
|
||||
dropped from the parameter name, the name is converted
|
||||
to lowercase and all underscore '_' characters are
|
||||
converted to dashes '-'.
|
||||
(baseaddr): the C_BASEADDR parameter.
|
||||
(HW_VER): from the HW_VER parameter.
|
||||
(size): equals C_HIGHADDR - C_BASEADDR + 1
|
||||
|
||||
Typically, the compatible list will include the exact IP core version
|
||||
followed by an older IP core version which implements the same
|
||||
interface or any other device with the same interface.
|
||||
|
||||
'reg', 'interrupt-parent' and 'interrupts' are all optional properties.
|
||||
|
||||
For example, the following block from system.mhs:
|
||||
|
||||
BEGIN opb_uartlite
|
||||
PARAMETER INSTANCE = opb_uartlite_0
|
||||
PARAMETER HW_VER = 1.00.b
|
||||
PARAMETER C_BAUDRATE = 115200
|
||||
PARAMETER C_DATA_BITS = 8
|
||||
PARAMETER C_ODD_PARITY = 0
|
||||
PARAMETER C_USE_PARITY = 0
|
||||
PARAMETER C_CLK_FREQ = 50000000
|
||||
PARAMETER C_BASEADDR = 0xEC100000
|
||||
PARAMETER C_HIGHADDR = 0xEC10FFFF
|
||||
BUS_INTERFACE SOPB = opb_7
|
||||
PORT OPB_Clk = CLK_50MHz
|
||||
PORT Interrupt = opb_uartlite_0_Interrupt
|
||||
PORT RX = opb_uartlite_0_RX
|
||||
PORT TX = opb_uartlite_0_TX
|
||||
PORT OPB_Rst = sys_bus_reset_0
|
||||
END
|
||||
|
||||
becomes the following device tree node:
|
||||
|
||||
opb-uartlite-0@ec100000 {
|
||||
device_type = "serial";
|
||||
compatible = "xlnx,opb-uartlite-1.00.b";
|
||||
reg = <ec100000 10000>;
|
||||
interrupt-parent = <&opb-intc>;
|
||||
interrupts = <1 0>; // got this from the opb_intc parameters
|
||||
current-speed = <d#115200>; // standard serial device prop
|
||||
clock-frequency = <d#50000000>; // standard serial device prop
|
||||
xlnx,data-bits = <8>;
|
||||
xlnx,odd-parity = <0>;
|
||||
xlnx,use-parity = <0>;
|
||||
};
|
||||
|
||||
Some IP cores actually implement 2 or more logical devices. In this case,
|
||||
the device should still describe the whole IP core with a single node
|
||||
and add a child node for each logical device. The ranges property can
|
||||
be used to translate from parent IP-core to the registers of each device.
|
||||
(Note: this makes the assumption that both logical devices have the same
|
||||
bus binding. If this is not true, then separate nodes should be used for
|
||||
each logical device). The 'cell-index' property can be used to enumerate
|
||||
logical devices within an IP core. For example, the following is the
|
||||
system.mhs entry for the dual ps2 controller found on the ml403 reference
|
||||
design.
|
||||
|
||||
BEGIN opb_ps2_dual_ref
|
||||
PARAMETER INSTANCE = opb_ps2_dual_ref_0
|
||||
PARAMETER HW_VER = 1.00.a
|
||||
PARAMETER C_BASEADDR = 0xA9000000
|
||||
PARAMETER C_HIGHADDR = 0xA9001FFF
|
||||
BUS_INTERFACE SOPB = opb_v20_0
|
||||
PORT Sys_Intr1 = ps2_1_intr
|
||||
PORT Sys_Intr2 = ps2_2_intr
|
||||
PORT Clkin1 = ps2_clk_rx_1
|
||||
PORT Clkin2 = ps2_clk_rx_2
|
||||
PORT Clkpd1 = ps2_clk_tx_1
|
||||
PORT Clkpd2 = ps2_clk_tx_2
|
||||
PORT Rx1 = ps2_d_rx_1
|
||||
PORT Rx2 = ps2_d_rx_2
|
||||
PORT Txpd1 = ps2_d_tx_1
|
||||
PORT Txpd2 = ps2_d_tx_2
|
||||
END
|
||||
|
||||
It would result in the following device tree nodes:
|
||||
|
||||
opb_ps2_dual_ref_0@a9000000 {
|
||||
ranges = <0 a9000000 2000>;
|
||||
// If this device had extra parameters, then they would
|
||||
// go here.
|
||||
ps2@0 {
|
||||
compatible = "xlnx,opb-ps2-dual-ref-1.00.a";
|
||||
reg = <0 40>;
|
||||
interrupt-parent = <&opb-intc>;
|
||||
interrupts = <3 0>;
|
||||
cell-index = <0>;
|
||||
};
|
||||
ps2@1000 {
|
||||
compatible = "xlnx,opb-ps2-dual-ref-1.00.a";
|
||||
reg = <1000 40>;
|
||||
interrupt-parent = <&opb-intc>;
|
||||
interrupts = <3 0>;
|
||||
cell-index = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
Also, the system.mhs file defines bus attachments from the processor
|
||||
to the devices. The device tree structure should reflect the bus
|
||||
attachments. Again an example; this system.mhs fragment:
|
||||
|
||||
BEGIN ppc405_virtex4
|
||||
PARAMETER INSTANCE = ppc405_0
|
||||
PARAMETER HW_VER = 1.01.a
|
||||
BUS_INTERFACE DPLB = plb_v34_0
|
||||
BUS_INTERFACE IPLB = plb_v34_0
|
||||
END
|
||||
|
||||
BEGIN opb_intc
|
||||
PARAMETER INSTANCE = opb_intc_0
|
||||
PARAMETER HW_VER = 1.00.c
|
||||
PARAMETER C_BASEADDR = 0xD1000FC0
|
||||
PARAMETER C_HIGHADDR = 0xD1000FDF
|
||||
BUS_INTERFACE SOPB = opb_v20_0
|
||||
END
|
||||
|
||||
BEGIN opb_uart16550
|
||||
PARAMETER INSTANCE = opb_uart16550_0
|
||||
PARAMETER HW_VER = 1.00.d
|
||||
PARAMETER C_BASEADDR = 0xa0000000
|
||||
PARAMETER C_HIGHADDR = 0xa0001FFF
|
||||
BUS_INTERFACE SOPB = opb_v20_0
|
||||
END
|
||||
|
||||
BEGIN plb_v34
|
||||
PARAMETER INSTANCE = plb_v34_0
|
||||
PARAMETER HW_VER = 1.02.a
|
||||
END
|
||||
|
||||
BEGIN plb_bram_if_cntlr
|
||||
PARAMETER INSTANCE = plb_bram_if_cntlr_0
|
||||
PARAMETER HW_VER = 1.00.b
|
||||
PARAMETER C_BASEADDR = 0xFFFF0000
|
||||
PARAMETER C_HIGHADDR = 0xFFFFFFFF
|
||||
BUS_INTERFACE SPLB = plb_v34_0
|
||||
END
|
||||
|
||||
BEGIN plb2opb_bridge
|
||||
PARAMETER INSTANCE = plb2opb_bridge_0
|
||||
PARAMETER HW_VER = 1.01.a
|
||||
PARAMETER C_RNG0_BASEADDR = 0x20000000
|
||||
PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF
|
||||
PARAMETER C_RNG1_BASEADDR = 0x60000000
|
||||
PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF
|
||||
PARAMETER C_RNG2_BASEADDR = 0x80000000
|
||||
PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF
|
||||
PARAMETER C_RNG3_BASEADDR = 0xC0000000
|
||||
PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF
|
||||
BUS_INTERFACE SPLB = plb_v34_0
|
||||
BUS_INTERFACE MOPB = opb_v20_0
|
||||
END
|
||||
|
||||
Gives this device tree (some properties removed for clarity):
|
||||
|
||||
plb-v34-0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
device_type = "ibm,plb";
|
||||
ranges; // 1:1 translation
|
||||
|
||||
plb-bram-if-cntrl-0@ffff0000 {
|
||||
reg = <ffff0000 10000>;
|
||||
}
|
||||
|
||||
opb-v20-0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges = <20000000 20000000 20000000
|
||||
60000000 60000000 20000000
|
||||
80000000 80000000 40000000
|
||||
c0000000 c0000000 20000000>;
|
||||
|
||||
opb-uart16550-0@a0000000 {
|
||||
reg = <a00000000 2000>;
|
||||
};
|
||||
|
||||
opb-intc-0@d1000fc0 {
|
||||
reg = <d1000fc0 20>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
That covers the general approach to binding xilinx IP cores into the
|
||||
device tree. The following are bindings for specific devices:
|
||||
|
||||
i) Xilinx ML300 Framebuffer
|
||||
|
||||
Simple framebuffer device from the ML300 reference design (also on the
|
||||
ML403 reference design as well as others).
|
||||
|
||||
Optional properties:
|
||||
- resolution = <xres yres> : pixel resolution of framebuffer. Some
|
||||
implementations use a different resolution.
|
||||
Default is <d#640 d#480>
|
||||
- virt-resolution = <xvirt yvirt> : Size of framebuffer in memory.
|
||||
Default is <d#1024 d#480>.
|
||||
- rotate-display (empty) : rotate display 180 degrees.
|
||||
|
||||
ii) Xilinx SystemACE
|
||||
|
||||
The Xilinx SystemACE device is used to program FPGAs from an FPGA
|
||||
bitstream stored on a CF card. It can also be used as a generic CF
|
||||
interface device.
|
||||
|
||||
Optional properties:
|
||||
- 8-bit (empty) : Set this property for SystemACE in 8 bit mode
|
||||
|
||||
iii) Xilinx EMAC and Xilinx TEMAC
|
||||
|
||||
Xilinx Ethernet devices. In addition to general xilinx properties
|
||||
listed above, nodes for these devices should include a phy-handle
|
||||
property, and may include other common network device properties
|
||||
like local-mac-address.
|
||||
|
||||
iv) Xilinx Uartlite
|
||||
|
||||
Xilinx uartlite devices are simple fixed speed serial ports.
|
||||
|
||||
Requred properties:
|
||||
- current-speed : Baud rate of uartlite
|
||||
|
||||
More devices will be defined as this spec matures.
|
||||
|
||||
VII - Specifying interrupt information for devices
|
||||
|
||||
Loading…
Reference in New Issue
Block a user