diff --git a/drivers/net/wireless/ralink/rt2x00/rt2x00.h b/drivers/net/wireless/ralink/rt2x00/rt2x00.h
index 4b1744e9fb78..50b92ca92bd7 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2x00.h
+++ b/drivers/net/wireless/ralink/rt2x00/rt2x00.h
@@ -673,7 +673,6 @@ enum rt2x00_state_flags {
 	CONFIG_CHANNEL_HT40,
 	CONFIG_POWERSAVING,
 	CONFIG_HT_DISABLED,
-	CONFIG_QOS_DISABLED,
 	CONFIG_MONITORING,
 
 	/*
diff --git a/drivers/net/wireless/ralink/rt2x00/rt2x00mac.c b/drivers/net/wireless/ralink/rt2x00/rt2x00mac.c
index 2825560e2424..e8462f25d252 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2x00mac.c
+++ b/drivers/net/wireless/ralink/rt2x00/rt2x00mac.c
@@ -642,18 +642,8 @@ void rt2x00mac_bss_info_changed(struct ieee80211_hw *hw,
 			rt2x00dev->intf_associated--;
 
 		rt2x00leds_led_assoc(rt2x00dev, !!rt2x00dev->intf_associated);
-
-		clear_bit(CONFIG_QOS_DISABLED, &rt2x00dev->flags);
 	}
 
-	/*
-	 * Check for access point which do not support 802.11e . We have to
-	 * generate data frames sequence number in S/W for such AP, because
-	 * of H/W bug.
-	 */
-	if (changes & BSS_CHANGED_QOS && !bss_conf->qos)
-		set_bit(CONFIG_QOS_DISABLED, &rt2x00dev->flags);
-
 	/*
 	 * When the erp information has changed, we should perform
 	 * additional configuration steps. For all other changes we are done.
diff --git a/drivers/net/wireless/ralink/rt2x00/rt2x00queue.c b/drivers/net/wireless/ralink/rt2x00/rt2x00queue.c
index 92ddc19e7bf7..4834b4eb0206 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2x00queue.c
+++ b/drivers/net/wireless/ralink/rt2x00/rt2x00queue.c
@@ -201,15 +201,18 @@ static void rt2x00queue_create_tx_descriptor_seq(struct rt2x00_dev *rt2x00dev,
 	if (!rt2x00_has_cap_flag(rt2x00dev, REQUIRE_SW_SEQNO)) {
 		/*
 		 * rt2800 has a H/W (or F/W) bug, device incorrectly increase
-		 * seqno on retransmited data (non-QOS) frames. To workaround
-		 * the problem let's generate seqno in software if QOS is
-		 * disabled.
+		 * seqno on retransmitted data (non-QOS) and management frames.
+		 * To workaround the problem let's generate seqno in software.
+		 * Except for beacons which are transmitted periodically by H/W
+		 * hence hardware has to assign seqno for them.
 		 */
-		if (test_bit(CONFIG_QOS_DISABLED, &rt2x00dev->flags))
-			__clear_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags);
-		else
+	    	if (ieee80211_is_beacon(hdr->frame_control)) {
+			__set_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags);
 			/* H/W will generate sequence number */
 			return;
+		}
+
+		__clear_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags);
 	}
 
 	/*