forked from Minki/linux
ARM: Device-tree updates
As always, a large number of DT updates. Too many to enumerate them all,
but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some set
top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other on-chip
ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current high-end
mobile SoCs.
It's great to see mainline support for it. So far, you
can't do much with it, since a lot of peripherals are not yet in the
DTs but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC upstream if
the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive entertainment-targeted
SoC. Currently only one Cortex-A53 CPU is enabled, we are eagerly
awaiting more. So far, basic drivers such as serial, gpios, PMU and
ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and ethernet
enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions might
not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support
-----BEGIN PGP SIGNATURE-----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=jLvk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Olof Johansson:
"As always, a large number of DT updates. Too many to enumerate them
all, but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some
set top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other
on-chip ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current
high-end mobile SoCs.
It's great to see mainline support for it. So far, you can't do
much with it, since a lot of peripherals are not yet in the DTs
but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC
upstream if the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive
entertainment-targeted SoC. Currently only one Cortex-A53 CPU is
enabled, we are eagerly awaiting more. So far, basic drivers
such as serial, gpios, PMU and ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and
ethernet enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions
might not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (448 commits)
ARM: dts: aspeed: Fix hwrng register address
arm64: dts: sprd: whale2: Add the rtc enable clock for watchdog
arm64: dts: sprd: Add GPIO and GPIO keys device nodes
arm64: dts: sprd: fix typo in 'remote-endpoint'
arm64: dts: apq8096-db820c: Removed bt-en-1-8v regulator
arm64: dts: fix regulator property name for wlan pcie endpoint
arm64: dts: qcom: msm8996: Use UFS_GDSC for UFS
ARM: dts: pxa3xx: fix MMC clocks
ARM: pxa: dts: add pin definitions for extended GPIOs
ARM: pxa: dts: add gpio-ranges to gpio controller
ARM: dts: ipq8074: Enable few peripherals for hk01 board
ARM: dts: ipq8074: Add pcie nodes
ARM: dts: ipq8074: Add peripheral nodes
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 board file
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk07.1 common data
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.dtsi
ARM: dts: ipq4019: Change the max opp frequency
...
This commit is contained in:
Linus Torvalds
commit
721afaa2ae
@ -5,3 +5,7 @@ KERNEL NEW DEPENDENCIES
|
||||
v4.3+ Update is needed for custom .config files to make sure
|
||||
CONFIG_REGULATOR_PBIAS is enabled for MMC1 to work
|
||||
properly.
|
||||
|
||||
v4.18+ Update is needed for custom .config files to make sure
|
||||
CONFIG_MMC_SDHCI_OMAP is enabled for all MMC instances
|
||||
to work in DRA7 and K2G based boards.
|
||||
|
||||
@ -25,6 +25,10 @@ Boards with the Amlogic Meson8b SoC shall have the following properties:
|
||||
Required root node property:
|
||||
compatible: "amlogic,meson8b";
|
||||
|
||||
Boards with the Amlogic Meson8m2 SoC shall have the following properties:
|
||||
Required root node property:
|
||||
compatible: "amlogic,meson8m2";
|
||||
|
||||
Boards with the Amlogic Meson GXBaby SoC shall have the following properties:
|
||||
Required root node property:
|
||||
compatible: "amlogic,meson-gxbb";
|
||||
@ -54,6 +58,8 @@ Board compatible values (alphabetically, grouped by SoC):
|
||||
- "hardkernel,odroid-c1" (Meson8b)
|
||||
- "tronfy,mxq" (Meson8b)
|
||||
|
||||
- "tronsmart,mxiii-plus" (Meson8m2)
|
||||
|
||||
- "amlogic,p200" (Meson gxbb)
|
||||
- "amlogic,p201" (Meson gxbb)
|
||||
- "friendlyarm,nanopi-k2" (Meson gxbb)
|
||||
|
||||
@ -34,6 +34,10 @@ Raspberry Pi 3 Model B
|
||||
Required root node properties:
|
||||
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
|
||||
|
||||
Raspberry Pi 3 Model B+
|
||||
Required root node properties:
|
||||
compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
|
||||
|
||||
Raspberry Pi Compute Module
|
||||
Required root node properties:
|
||||
compatible = "raspberrypi,compute-module", "brcm,bcm2835";
|
||||
|
||||
@ -21,8 +21,6 @@ Required root node properties:
|
||||
- "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board.
|
||||
- "samsung,tm2" - for Exynos5433-based Samsung TM2 board.
|
||||
- "samsung,tm2e" - for Exynos5433-based Samsung TM2E board.
|
||||
- "samsung,sd5v1" - for Exynos5440-based Samsung board.
|
||||
- "samsung,ssdk5440" - for Exynos5440-based Samsung board.
|
||||
|
||||
* Other companies Exynos SoC based
|
||||
* FriendlyARM
|
||||
|
||||
@ -47,6 +47,8 @@ SoCs:
|
||||
compatible = "renesas,r8a77970"
|
||||
- R-Car V3H (R8A77980)
|
||||
compatible = "renesas,r8a77980"
|
||||
- R-Car E3 (R8A77990)
|
||||
compatible = "renesas,r8a77990"
|
||||
- R-Car D3 (R8A77995)
|
||||
compatible = "renesas,r8a77995"
|
||||
|
||||
@ -69,6 +71,8 @@ Boards:
|
||||
compatible = "renesas,draak", "renesas,r8a77995"
|
||||
- Eagle (RTP0RC77970SEB0010S)
|
||||
compatible = "renesas,eagle", "renesas,r8a77970"
|
||||
- Ebisu (RTP0RC77990SEB0010S)
|
||||
compatible = "renesas,ebisu", "renesas,r8a77990"
|
||||
- Genmai (RTK772100BC00000BR)
|
||||
compatible = "renesas,genmai", "renesas,r7s72100"
|
||||
- GR-Peach (X28A-M01-E/F)
|
||||
@ -80,6 +84,8 @@ Boards:
|
||||
compatible = "renesas,h3ulcb", "renesas,r8a7795"
|
||||
- Henninger
|
||||
compatible = "renesas,henninger", "renesas,r8a7791"
|
||||
- iWave Systems RZ/G1C Single Board Computer (iW-RainboW-G23S)
|
||||
compatible = "iwave,g23s", "renesas,r8a77470"
|
||||
- iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D)
|
||||
compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745"
|
||||
- iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM)
|
||||
@ -110,7 +116,7 @@ Boards:
|
||||
compatible = "renesas,salvator-x", "renesas,r8a7795"
|
||||
- Salvator-X (RTP0RC7796SIPB0011S)
|
||||
compatible = "renesas,salvator-x", "renesas,r8a7796"
|
||||
- Salvator-X (RTP0RC7796SIPB0011S (M3N))
|
||||
- Salvator-X (RTP0RC7796SIPB0011S (M3-N))
|
||||
compatible = "renesas,salvator-x", "renesas,r8a77965"
|
||||
- Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S)
|
||||
compatible = "renesas,salvator-xs", "renesas,r8a7795"
|
||||
@ -126,6 +132,8 @@ Boards:
|
||||
compatible = "renesas,sk-rzg1m", "renesas,r8a7743"
|
||||
- Stout (ADAS Starterkit, Y-R-CAR-ADAS-SKH2-BOARD)
|
||||
compatible = "renesas,stout", "renesas,r8a7790"
|
||||
- V3HSK (Y-ASK-RCAR-V3H-WS10)
|
||||
compatible = "renesas,v3hsk", "renesas,r8a77980"
|
||||
- V3MSK (Y-ASK-RCAR-V3M-WS10)
|
||||
compatible = "renesas,v3msk", "renesas,r8a77970"
|
||||
- Wheat (RTP0RC7792ASKB0000JE)
|
||||
|
||||
@ -1,18 +0,0 @@
|
||||
NVIDIA Tegra30 MC(Memory Controller)
|
||||
|
||||
Required properties:
|
||||
- compatible : "nvidia,tegra30-mc"
|
||||
- reg : Should contain 4 register ranges(address and length); see the
|
||||
example below. Note that the MC registers are interleaved with the
|
||||
SMMU registers, and hence must be represented as multiple ranges.
|
||||
- interrupts : Should contain MC General interrupt.
|
||||
|
||||
Example:
|
||||
memory-controller {
|
||||
compatible = "nvidia,tegra30-mc";
|
||||
reg = <0x7000f000 0x010
|
||||
0x7000f03c 0x1b4
|
||||
0x7000f200 0x028
|
||||
0x7000f284 0x17c>;
|
||||
interrupts = <0 77 0x04>;
|
||||
};
|
||||
@ -10,9 +10,6 @@ Required Properties:
|
||||
"amlogic,gxl-clkc" for GXL and GXM SoC,
|
||||
"amlogic,axg-clkc" for AXG SoC.
|
||||
|
||||
- reg: physical base address of the clock controller and length of memory
|
||||
mapped region.
|
||||
|
||||
- #clock-cells: should be 1.
|
||||
|
||||
Each clock is assigned an identifier and client nodes can use this identifier
|
||||
@ -20,13 +17,22 @@ to specify the clock which they consume. All available clocks are defined as
|
||||
preprocessor macros in the dt-bindings/clock/gxbb-clkc.h header and can be
|
||||
used in device tree sources.
|
||||
|
||||
Parent node should have the following properties :
|
||||
- compatible: "syscon", "simple-mfd, and "amlogic,meson-gx-hhi-sysctrl" or
|
||||
"amlogic,meson-axg-hhi-sysctrl"
|
||||
- reg: base address and size of the HHI system control register space.
|
||||
|
||||
Example: Clock controller node:
|
||||
|
||||
clkc: clock-controller@c883c000 {
|
||||
sysctrl: system-controller@0 {
|
||||
compatible = "amlogic,meson-gx-hhi-sysctrl", "syscon", "simple-mfd";
|
||||
reg = <0 0 0 0x400>;
|
||||
|
||||
clkc: clock-controller {
|
||||
#clock-cells = <1>;
|
||||
compatible = "amlogic,gxbb-clkc";
|
||||
reg = <0x0 0xc883c000 0x0 0x3db>;
|
||||
};
|
||||
};
|
||||
|
||||
Example: UART controller node that consumes the clock generated by the clock
|
||||
controller:
|
||||
|
||||
@ -6,11 +6,21 @@ Required properties:
|
||||
example below. Note that the MC registers are interleaved with the
|
||||
GART registers, and hence must be represented as multiple ranges.
|
||||
- interrupts : Should contain MC General interrupt.
|
||||
- #reset-cells : Should be 1. This cell represents memory client module ID.
|
||||
The assignments may be found in header file <dt-bindings/memory/tegra20-mc.h>
|
||||
or in the TRM documentation.
|
||||
|
||||
Example:
|
||||
memory-controller@7000f000 {
|
||||
mc: memory-controller@7000f000 {
|
||||
compatible = "nvidia,tegra20-mc";
|
||||
reg = <0x7000f000 0x024
|
||||
0x7000f03c 0x3c4>;
|
||||
interrupts = <0 77 0x04>;
|
||||
#reset-cells = <1>;
|
||||
};
|
||||
|
||||
video-codec@6001a000 {
|
||||
compatible = "nvidia,tegra20-vde";
|
||||
...
|
||||
resets = <&mc TEGRA20_MC_RESET_VDE>;
|
||||
};
|
||||
|
||||
@ -12,6 +12,9 @@ Required properties:
|
||||
- clock-names: Must include the following entries:
|
||||
- mc: the module's clock input
|
||||
- interrupts: The interrupt outputs from the controller.
|
||||
- #reset-cells : Should be 1. This cell represents memory client module ID.
|
||||
The assignments may be found in header file <dt-bindings/memory/tegra30-mc.h>
|
||||
or in the TRM documentation.
|
||||
|
||||
Required properties for Tegra30, Tegra114, Tegra124, Tegra132 and Tegra210:
|
||||
- #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines
|
||||
@ -72,12 +75,14 @@ Example SoC include file:
|
||||
interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
#iommu-cells = <1>;
|
||||
#reset-cells = <1>;
|
||||
};
|
||||
|
||||
sdhci@700b0000 {
|
||||
compatible = "nvidia,tegra124-sdhci";
|
||||
...
|
||||
iommus = <&mc TEGRA_SWGROUP_SDMMC1A>;
|
||||
resets = <&mc TEGRA124_MC_RESET_SDMMC1>;
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
@ -4,6 +4,7 @@ Required properties:
|
||||
- compatible: Should be one of the following:
|
||||
"allwinner,sun4i-a10-sid"
|
||||
"allwinner,sun7i-a20-sid"
|
||||
"allwinner,sun8i-a83t-sid"
|
||||
"allwinner,sun8i-h3-sid"
|
||||
"allwinner,sun50i-a64-sid"
|
||||
|
||||
|
||||
@ -0,0 +1,37 @@
|
||||
Command DB
|
||||
---------
|
||||
|
||||
Command DB is a database that provides a mapping between resource key and the
|
||||
resource address for a system resource managed by a remote processor. The data
|
||||
is stored in a shared memory region and is loaded by the remote processor.
|
||||
|
||||
Some of the Qualcomm Technologies Inc SoC's have hardware accelerators for
|
||||
controlling shared resources. Depending on the board configuration the shared
|
||||
resource properties may change. These properties are dynamically probed by the
|
||||
remote processor and made available in the shared memory.
|
||||
|
||||
The bindings for Command DB is specified in the reserved-memory section in
|
||||
devicetree. The devicetree representation of the command DB driver should be:
|
||||
|
||||
Properties:
|
||||
- compatible:
|
||||
Usage: required
|
||||
Value type: <string>
|
||||
Definition: Should be "qcom,cmd-db"
|
||||
|
||||
- reg:
|
||||
Usage: required
|
||||
Value type: <prop encoded array>
|
||||
Definition: The register address that points to the actual location of
|
||||
the Command DB in memory.
|
||||
|
||||
Example:
|
||||
|
||||
reserved-memory {
|
||||
[...]
|
||||
reserved-memory@85fe0000 {
|
||||
reg = <0x0 0x85fe0000 0x0 0x20000>;
|
||||
compatible = "qcom,cmd-db";
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
@ -14,11 +14,16 @@ Optional properties:
|
||||
- clocks : phandle to clock-controller plus clock-specifier pair
|
||||
- clock-names : "ipsec" as a clock name
|
||||
|
||||
Optional properties:
|
||||
|
||||
- interrupts: specify the interrupt for the RNG block
|
||||
|
||||
Example:
|
||||
|
||||
rng {
|
||||
compatible = "brcm,bcm2835-rng";
|
||||
reg = <0x7e104000 0x10>;
|
||||
compatible = "brcm,bcm2835-rng";
|
||||
reg = <0x7e104000 0x10>;
|
||||
interrupts = <2 29>;
|
||||
};
|
||||
|
||||
rng@18033000 {
|
||||
|
||||
119
Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
Normal file
119
Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
Normal file
@ -0,0 +1,119 @@
|
||||
Qualcomm Technologies, Inc. GENI Serial Engine QUP Wrapper Controller
|
||||
|
||||
Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) wrapper
|
||||
is a programmable module for supporting a wide range of serial interfaces
|
||||
like UART, SPI, I2C, I3C, etc. A single QUP module can provide upto 8 Serial
|
||||
Interfaces, using its internal Serial Engines. The GENI Serial Engine QUP
|
||||
Wrapper controller is modeled as a node with zero or more child nodes each
|
||||
representing a serial engine.
|
||||
|
||||
Required properties:
|
||||
- compatible: Must be "qcom,geni-se-qup".
|
||||
- reg: Must contain QUP register address and length.
|
||||
- clock-names: Must contain "m-ahb" and "s-ahb".
|
||||
- clocks: AHB clocks needed by the device.
|
||||
|
||||
Required properties if child node exists:
|
||||
- #address-cells: Must be <1> for Serial Engine Address
|
||||
- #size-cells: Must be <1> for Serial Engine Address Size
|
||||
- ranges: Must be present
|
||||
|
||||
Properties for children:
|
||||
|
||||
A GENI based QUP wrapper controller node can contain 0 or more child nodes
|
||||
representing serial devices. These serial devices can be a QCOM UART, I2C
|
||||
controller, SPI controller, or some combination of aforementioned devices.
|
||||
Please refer below the child node definitions for the supported serial
|
||||
interface protocols.
|
||||
|
||||
Qualcomm Technologies Inc. GENI Serial Engine based I2C Controller
|
||||
|
||||
Required properties:
|
||||
- compatible: Must be "qcom,geni-i2c".
|
||||
- reg: Must contain QUP register address and length.
|
||||
- interrupts: Must contain I2C interrupt.
|
||||
- clock-names: Must contain "se".
|
||||
- clocks: Serial engine core clock needed by the device.
|
||||
- #address-cells: Must be <1> for I2C device address.
|
||||
- #size-cells: Must be <0> as I2C addresses have no size component.
|
||||
|
||||
Optional property:
|
||||
- clock-frequency: Desired I2C bus clock frequency in Hz.
|
||||
When missing default to 400000Hz.
|
||||
|
||||
Child nodes should conform to I2C bus binding as described in i2c.txt.
|
||||
|
||||
Qualcomm Technologies Inc. GENI Serial Engine based UART Controller
|
||||
|
||||
Required properties:
|
||||
- compatible: Must be "qcom,geni-debug-uart".
|
||||
- reg: Must contain UART register location and length.
|
||||
- interrupts: Must contain UART core interrupts.
|
||||
- clock-names: Must contain "se".
|
||||
- clocks: Serial engine core clock needed by the device.
|
||||
|
||||
Qualcomm Technologies Inc. GENI Serial Engine based SPI Controller
|
||||
|
||||
Required properties:
|
||||
- compatible: Must contain "qcom,geni-spi".
|
||||
- reg: Must contain SPI register location and length.
|
||||
- interrupts: Must contain SPI controller interrupts.
|
||||
- clock-names: Must contain "se".
|
||||
- clocks: Serial engine core clock needed by the device.
|
||||
- spi-max-frequency: Specifies maximum SPI clock frequency, units - Hz.
|
||||
- #address-cells: Must be <1> to define a chip select address on
|
||||
the SPI bus.
|
||||
- #size-cells: Must be <0>.
|
||||
|
||||
SPI slave nodes must be children of the SPI master node and conform to SPI bus
|
||||
binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt.
|
||||
|
||||
Example:
|
||||
geniqup@8c0000 {
|
||||
compatible = "qcom,geni-se-qup";
|
||||
reg = <0x8c0000 0x6000>;
|
||||
clock-names = "m-ahb", "s-ahb";
|
||||
clocks = <&clock_gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
|
||||
<&clock_gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
|
||||
i2c0: i2c@a94000 {
|
||||
compatible = "qcom,geni-i2c";
|
||||
reg = <0xa94000 0x4000>;
|
||||
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clock-names = "se";
|
||||
clocks = <&clock_gcc GCC_QUPV3_WRAP0_S5_CLK>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&qup_1_i2c_5_active>;
|
||||
pinctrl-1 = <&qup_1_i2c_5_sleep>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
uart0: serial@a88000 {
|
||||
compatible = "qcom,geni-debug-uart";
|
||||
reg = <0xa88000 0x7000>;
|
||||
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clock-names = "se";
|
||||
clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&qup_1_uart_3_active>;
|
||||
pinctrl-1 = <&qup_1_uart_3_sleep>;
|
||||
};
|
||||
|
||||
spi0: spi@a84000 {
|
||||
compatible = "qcom,geni-spi";
|
||||
reg = <0xa84000 0x4000>;
|
||||
interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clock-names = "se";
|
||||
clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&qup_1_spi_2_active>;
|
||||
pinctrl-1 = <&qup_1_spi_2_sleep>;
|
||||
spi-max-frequency = <19200000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
}
|
||||
@ -22,6 +22,10 @@ Required Properties:
|
||||
|
||||
- "renesas,r8a73a4-cmt0" for the 32-bit CMT0 device included in r8a73a4.
|
||||
- "renesas,r8a73a4-cmt1" for the 48-bit CMT1 device included in r8a73a4.
|
||||
- "renesas,r8a7743-cmt0" for the 32-bit CMT0 device included in r8a7743.
|
||||
- "renesas,r8a7743-cmt1" for the 48-bit CMT1 device included in r8a7743.
|
||||
- "renesas,r8a7745-cmt0" for the 32-bit CMT0 device included in r8a7745.
|
||||
- "renesas,r8a7745-cmt1" for the 48-bit CMT1 device included in r8a7745.
|
||||
- "renesas,r8a7790-cmt0" for the 32-bit CMT0 device included in r8a7790.
|
||||
- "renesas,r8a7790-cmt1" for the 48-bit CMT1 device included in r8a7790.
|
||||
- "renesas,r8a7791-cmt0" for the 32-bit CMT0 device included in r8a7791.
|
||||
@ -31,10 +35,12 @@ Required Properties:
|
||||
- "renesas,r8a7794-cmt0" for the 32-bit CMT0 device included in r8a7794.
|
||||
- "renesas,r8a7794-cmt1" for the 48-bit CMT1 device included in r8a7794.
|
||||
|
||||
- "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2.
|
||||
- "renesas,rcar-gen2-cmt1" for 48-bit CMT1 devices included in R-Car Gen2.
|
||||
These are fallbacks for r8a73a4 and all the R-Car Gen2
|
||||
entries listed above.
|
||||
- "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2
|
||||
and RZ/G1.
|
||||
- "renesas,rcar-gen2-cmt1" for 48-bit CMT1 devices included in R-Car Gen2
|
||||
and RZ/G1.
|
||||
These are fallbacks for r8a73a4, R-Car Gen2 and RZ/G1 entries
|
||||
listed above.
|
||||
|
||||
- reg: base address and length of the registers block for the timer module.
|
||||
- interrupts: interrupt-specifier for the timer, one per channel.
|
||||
|
||||
@ -58,6 +58,7 @@ bosch Bosch Sensortec GmbH
|
||||
boundary Boundary Devices Inc.
|
||||
brcm Broadcom Corporation
|
||||
buffalo Buffalo, Inc.
|
||||
bticino Bticino International
|
||||
calxeda Calxeda
|
||||
capella Capella Microsystems, Inc
|
||||
cascoda Cascoda, Ltd.
|
||||
@ -285,6 +286,7 @@ pine64 Pine64
|
||||
pixcir PIXCIR MICROELECTRONICS Co., Ltd
|
||||
plathome Plat'Home Co., Ltd.
|
||||
plda PLDA
|
||||
portwell Portwell Inc.
|
||||
poslab Poslab Technology Co., Ltd.
|
||||
powervr PowerVR (deprecated, use img)
|
||||
probox2 PROBOX2 (by W2COMP Co., Ltd.)
|
||||
|
||||
@ -75,6 +75,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
|
||||
bcm2835-rpi-a-plus.dtb \
|
||||
bcm2836-rpi-2-b.dtb \
|
||||
bcm2837-rpi-3-b.dtb \
|
||||
bcm2837-rpi-3-b-plus.dtb \
|
||||
bcm2835-rpi-zero.dtb \
|
||||
bcm2835-rpi-zero-w.dtb
|
||||
dtb-$(CONFIG_ARCH_BCM_5301X) += \
|
||||
@ -102,8 +103,10 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
|
||||
bcm47094-dlink-dir-885l.dtb \
|
||||
bcm47094-linksys-panamera.dtb \
|
||||
bcm47094-luxul-abr-4500.dtb \
|
||||
bcm47094-luxul-xap-1610.dtb \
|
||||
bcm47094-luxul-xbr-4500.dtb \
|
||||
bcm47094-luxul-xwr-3100.dtb \
|
||||
bcm47094-luxul-xwr-3150-v1.dtb \
|
||||
bcm47094-netgear-r8500.dtb \
|
||||
bcm94708.dtb \
|
||||
bcm94709.dtb \
|
||||
@ -140,6 +143,7 @@ dtb-$(CONFIG_ARCH_BCM_NSP) += \
|
||||
dtb-$(CONFIG_ARCH_BERLIN) += \
|
||||
berlin2-sony-nsz-gs7.dtb \
|
||||
berlin2cd-google-chromecast.dtb \
|
||||
berlin2cd-valve-steamlink.dtb \
|
||||
berlin2q-marvell-dmp.dtb
|
||||
dtb-$(CONFIG_ARCH_BRCMSTB) += \
|
||||
bcm7445-bcm97445svmb.dtb
|
||||
@ -190,8 +194,6 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \
|
||||
exynos5422-odroidxu3.dtb \
|
||||
exynos5422-odroidxu3-lite.dtb \
|
||||
exynos5422-odroidxu4.dtb \
|
||||
exynos5440-sd5v1.dtb \
|
||||
exynos5440-ssdk5440.dtb \
|
||||
exynos5800-peach-pi.dtb
|
||||
dtb-$(CONFIG_ARCH_GEMINI) += \
|
||||
gemini-dlink-dir-685.dtb \
|
||||
@ -312,14 +314,14 @@ dtb-$(CONFIG_ARCH_NPCM7XX) += \
|
||||
dtb-$(CONFIG_MACH_MESON6) += \
|
||||
meson6-atv1200.dtb
|
||||
dtb-$(CONFIG_MACH_MESON8) += \
|
||||
meson8-minix-neo-x8.dtb
|
||||
meson8-minix-neo-x8.dtb \
|
||||
meson8b-mxq.dtb \
|
||||
meson8b-odroidc1.dtb \
|
||||
meson8m2-mxiii-plus.dtb
|
||||
dtb-$(CONFIG_ARCH_MMP) += \
|
||||
pxa168-aspenite.dtb \
|
||||
pxa910-dkb.dtb \
|
||||
mmp2-brownstone.dtb
|
||||
dtb-$(CONFIG_MACH_MESON8B) += \
|
||||
meson8b-mxq.dtb \
|
||||
meson8b-odroidc1.dtb
|
||||
dtb-$(CONFIG_ARCH_MPS2) += \
|
||||
mps2-an385.dtb \
|
||||
mps2-an399.dtb
|
||||
@ -399,6 +401,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
|
||||
imx6dl-hummingboard2-som-v15.dtb \
|
||||
imx6dl-icore.dtb \
|
||||
imx6dl-icore-rqs.dtb \
|
||||
imx6dl-mamoj.dtb \
|
||||
imx6dl-nit6xlite.dtb \
|
||||
imx6dl-nitrogen6x.dtb \
|
||||
imx6dl-phytec-mira-rdk-nand.dtb \
|
||||
@ -439,6 +442,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
|
||||
imx6q-cubox-i-emmc-som-v15.dtb \
|
||||
imx6q-cubox-i-som-v15.dtb \
|
||||
imx6q-dfi-fs700-m60.dtb \
|
||||
imx6q-dhcom-pdk2.dtb \
|
||||
imx6q-display5-tianma-tm070-1280x768.dtb \
|
||||
imx6q-dmo-edmqmx6.dtb \
|
||||
imx6q-dms-ba16.dtb \
|
||||
@ -463,9 +467,11 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
|
||||
imx6q-hummingboard2-emmc-som-v15.dtb \
|
||||
imx6q-hummingboard2-som-v15.dtb \
|
||||
imx6q-icore.dtb \
|
||||
imx6q-icore-mipi.dtb \
|
||||
imx6q-icore-ofcap10.dtb \
|
||||
imx6q-icore-ofcap12.dtb \
|
||||
imx6q-icore-rqs.dtb \
|
||||
imx6q-kp-tpc.dtb \
|
||||
imx6q-marsboard.dtb \
|
||||
imx6q-mccmon6.dtb \
|
||||
imx6q-nitrogen6x.dtb \
|
||||
@ -688,6 +694,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
|
||||
am335x-pdu001.dtb \
|
||||
am335x-pepper.dtb \
|
||||
am335x-phycore-rdk.dtb \
|
||||
am335x-pocketbeagle.dtb \
|
||||
am335x-shc.dtb \
|
||||
am335x-sbc-t335.dtb \
|
||||
am335x-sl50.dtb \
|
||||
@ -760,12 +767,17 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
qcom-ipq4019-ap.dk01.1-c1.dtb \
|
||||
qcom-ipq4019-ap.dk04.1-c1.dtb \
|
||||
qcom-ipq4019-ap.dk04.1-c3.dtb \
|
||||
qcom-ipq4019-ap.dk07.1-c1.dtb \
|
||||
qcom-ipq4019-ap.dk07.1-c2.dtb \
|
||||
qcom-ipq8064-ap148.dtb \
|
||||
qcom-msm8660-surf.dtb \
|
||||
qcom-msm8960-cdp.dtb \
|
||||
qcom-msm8974-fairphone-fp2.dtb \
|
||||
qcom-msm8974-lge-nexus5-hammerhead.dtb \
|
||||
qcom-msm8974-samsung-klte.dtb \
|
||||
qcom-msm8974-sony-xperia-amami.dtb \
|
||||
qcom-msm8974-sony-xperia-castor.dtb \
|
||||
qcom-msm8974-sony-xperia-honami.dtb \
|
||||
qcom-mdm9615-wp8548-mangoh-green.dtb
|
||||
@ -959,6 +971,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
|
||||
sun7i-a20-m3.dtb \
|
||||
sun7i-a20-mk808c.dtb \
|
||||
sun7i-a20-olimex-som-evb.dtb \
|
||||
sun7i-a20-olimex-som-evb-emmc.dtb \
|
||||
sun7i-a20-olimex-som204-evb.dtb \
|
||||
sun7i-a20-olimex-som204-evb-emmc.dtb \
|
||||
sun7i-a20-olinuxino-lime.dtb \
|
||||
@ -992,8 +1005,9 @@ dtb-$(CONFIG_MACH_SUN8I) += \
|
||||
sun8i-a83t-bananapi-m3.dtb \
|
||||
sun8i-a83t-cubietruck-plus.dtb \
|
||||
sun8i-a83t-tbs-a711.dtb \
|
||||
sun8i-h2-plus-orangepi-r1.dtb \
|
||||
sun8i-h2-plus-bananapi-m2-zero.dtb \
|
||||
sun8i-h2-plus-libretech-all-h3-cc.dtb \
|
||||
sun8i-h2-plus-orangepi-r1.dtb \
|
||||
sun8i-h2-plus-orangepi-zero.dtb \
|
||||
sun8i-h3-bananapi-m2-plus.dtb \
|
||||
sun8i-h3-beelink-x2.dtb \
|
||||
@ -1010,6 +1024,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
|
||||
sun8i-h3-orangepi-plus.dtb \
|
||||
sun8i-h3-orangepi-plus2e.dtb \
|
||||
sun8i-r16-bananapi-m2m.dtb \
|
||||
sun8i-r16-nintendo-nes-classic.dtb \
|
||||
sun8i-r16-nintendo-super-nes-classic.dtb \
|
||||
sun8i-r16-parrot.dtb \
|
||||
sun8i-r40-bananapi-m2-ultra.dtb \
|
||||
sun8i-v3s-licheepi-zero.dtb \
|
||||
@ -1054,9 +1070,7 @@ dtb-$(CONFIG_ARCH_U8500) += \
|
||||
ste-hrefprev60-stuib.dtb \
|
||||
ste-hrefprev60-tvk.dtb \
|
||||
ste-hrefv60plus-stuib.dtb \
|
||||
ste-hrefv60plus-tvk.dtb \
|
||||
ste-ccu8540.dtb \
|
||||
ste-ccu9540.dtb
|
||||
ste-hrefv60plus-tvk.dtb
|
||||
dtb-$(CONFIG_ARCH_UNIPHIER) += \
|
||||
uniphier-ld4-ref.dtb \
|
||||
uniphier-ld6b-ref.dtb \
|
||||
@ -1150,6 +1164,9 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
|
||||
mt6580-evbp1.dtb \
|
||||
mt6589-aquaris5.dtb \
|
||||
mt6592-evb.dtb \
|
||||
mt7623a-rfb-emmc.dtb \
|
||||
mt7623a-rfb-nand.dtb \
|
||||
mt7623n-rfb-emmc.dtb \
|
||||
mt7623n-rfb-nand.dtb \
|
||||
mt7623n-bananapi-bpi-r2.dtb \
|
||||
mt8127-moose.dtb \
|
||||
@ -1158,8 +1175,11 @@ dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
|
||||
dtb-$(CONFIG_ARCH_ASPEED) += \
|
||||
aspeed-ast2500-evb.dtb \
|
||||
aspeed-bmc-arm-centriq2400-rep.dtb \
|
||||
aspeed-bmc-intel-s2600wf.dtb \
|
||||
aspeed-bmc-opp-lanyang.dtb \
|
||||
aspeed-bmc-opp-palmetto.dtb \
|
||||
aspeed-bmc-opp-romulus.dtb \
|
||||
aspeed-bmc-opp-witherspoon.dtb \
|
||||
aspeed-bmc-opp-zaius.dtb \
|
||||
aspeed-bmc-portwell-neptune.dtb \
|
||||
aspeed-bmc-quanta-q71l.dtb
|
||||
|
||||
@ -85,7 +85,7 @@
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <20 GPIO_ACTIVE_LOW>;
|
||||
interrupts = <20 IRQ_TYPE_EDGE_RISING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&tca6416_pins>;
|
||||
};
|
||||
|
||||
@ -94,7 +94,7 @@
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <20 GPIO_ACTIVE_LOW>;
|
||||
interrupts = <20 IRQ_TYPE_EDGE_RISING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&tca6416_pins>;
|
||||
};
|
||||
|
||||
@ -249,7 +249,7 @@
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <28 GPIO_ACTIVE_LOW>;
|
||||
interrupts = <28 IRQ_TYPE_EDGE_RISING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&tps65910_pins>;
|
||||
};
|
||||
|
||||
@ -161,7 +161,14 @@
|
||||
|
||||
mmc1_pins: pinmux_mmc1_pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
|
||||
AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spio0_cs1.gpio0_6 */
|
||||
AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
|
||||
AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
|
||||
AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
|
||||
AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
|
||||
AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
|
||||
AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */
|
||||
AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* mcasp0_aclkr.mmc0_sdwp */
|
||||
>;
|
||||
};
|
||||
|
||||
|
||||
@ -364,7 +364,7 @@
|
||||
compatible = "invensense,mpu9250";
|
||||
reg = <0x68>;
|
||||
interrupt-parent = <&gpio3>;
|
||||
interrupts = <21 GPIO_ACTIVE_LOW>;
|
||||
interrupts = <21 IRQ_TYPE_EDGE_RISING>;
|
||||
i2c-gate {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
@ -303,7 +303,14 @@
|
||||
|
||||
mmc1_pins: pinmux_mmc1_pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
|
||||
AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
|
||||
AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
|
||||
AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
|
||||
AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
|
||||
AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
|
||||
AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
|
||||
AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */
|
||||
AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* mcasp0_aclkr.mmc0_sdwp */
|
||||
>;
|
||||
};
|
||||
|
||||
|
||||
@ -137,7 +137,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
backlight {
|
||||
lcd_bl: backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&ecap2 0 50000 PWM_POLARITY_INVERTED>;
|
||||
brightness-levels = <0 58 61 66 75 90 125 170 255>;
|
||||
@ -172,6 +172,7 @@
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&lcd_pins_default>;
|
||||
pinctrl-1 = <&lcd_pins_sleep>;
|
||||
backlight = <&lcd_bl>;
|
||||
status = "okay";
|
||||
panel-info {
|
||||
ac-bias = <255>;
|
||||
@ -399,7 +400,14 @@
|
||||
|
||||
mmc1_pins: pinmux_mmc1_pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
|
||||
AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
|
||||
AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
|
||||
AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
|
||||
AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
|
||||
AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
|
||||
AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
|
||||
AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */
|
||||
AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* mcasp0_aclkr.mmc0_sdwp */
|
||||
>;
|
||||
};
|
||||
|
||||
|
||||
124
arch/arm/boot/dts/am335x-osd335x-common.dtsi
Normal file
124
arch/arm/boot/dts/am335x-osd335x-common.dtsi
Normal file
@ -0,0 +1,124 @@
|
||||
// SPDX-License-Identifier: GPL-2.0
|
||||
/*
|
||||
* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
|
||||
*
|
||||
* Author: Robert Nelson <robertcnelson@gmail.com>
|
||||
*/
|
||||
|
||||
/ {
|
||||
cpus {
|
||||
cpu@0 {
|
||||
cpu0-supply = <&dcdc2_reg>;
|
||||
};
|
||||
};
|
||||
|
||||
memory@80000000 {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x20000000>; /* 512 MB */
|
||||
};
|
||||
};
|
||||
|
||||
&cpu0_opp_table {
|
||||
/*
|
||||
* Octavo Systems:
|
||||
* The EFUSE_SMA register is not programmed for any of the AM335x wafers
|
||||
* we get and we are not programming them during our production test.
|
||||
* Therefore, from a DEVICE_ID revision point of view, the silicon looks
|
||||
* like it is Revision 2.1. However, from an EFUSE_SMA point of view for
|
||||
* the HW OPP table, the silicon looks like it is Revision 1.0 (ie the
|
||||
* EFUSE_SMA register reads as all zeros).
|
||||
*/
|
||||
oppnitro-1000000000 {
|
||||
opp-supported-hw = <0x06 0x0100>;
|
||||
};
|
||||
};
|
||||
|
||||
&am33xx_pinmux {
|
||||
i2c0_pins: pinmux-i2c0-pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* (C17) I2C0_SDA.I2C0_SDA */
|
||||
AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* (C16) I2C0_SCL.I2C0_SCL */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c0_pins>;
|
||||
|
||||
status = "okay";
|
||||
clock-frequency = <400000>;
|
||||
|
||||
tps: tps@24 {
|
||||
reg = <0x24>;
|
||||
};
|
||||
};
|
||||
|
||||
/include/ "tps65217.dtsi"
|
||||
|
||||
&tps {
|
||||
interrupts = <7>; /* NMI */
|
||||
interrupt-parent = <&intc>;
|
||||
|
||||
ti,pmic-shutdown-controller;
|
||||
|
||||
pwrbutton {
|
||||
interrupts = <2>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
regulators {
|
||||
dcdc1_reg: regulator@0 {
|
||||
regulator-name = "vdds_dpr";
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
dcdc2_reg: regulator@1 {
|
||||
/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
|
||||
regulator-name = "vdd_mpu";
|
||||
regulator-min-microvolt = <925000>;
|
||||
regulator-max-microvolt = <1351500>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
dcdc3_reg: regulator@2 {
|
||||
/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
|
||||
regulator-name = "vdd_core";
|
||||
regulator-min-microvolt = <925000>;
|
||||
regulator-max-microvolt = <1150000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
ldo1_reg: regulator@3 {
|
||||
regulator-name = "vio,vrtc,vdds";
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
ldo2_reg: regulator@4 {
|
||||
regulator-name = "vdd_3v3aux";
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
ldo3_reg: regulator@5 {
|
||||
regulator-name = "vdd_1v8";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
ldo4_reg: regulator@6 {
|
||||
regulator-name = "vdd_3v3a";
|
||||
regulator-always-on;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&aes {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sham {
|
||||
status = "okay";
|
||||
};
|
||||
237
arch/arm/boot/dts/am335x-pocketbeagle.dts
Normal file
237
arch/arm/boot/dts/am335x-pocketbeagle.dts
Normal file
@ -0,0 +1,237 @@
|
||||
// SPDX-License-Identifier: GPL-2.0
|
||||
/*
|
||||
* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
|
||||
*
|
||||
* Author: Robert Nelson <robertcnelson@gmail.com>
|
||||
*/
|
||||
/dts-v1/;
|
||||
|
||||
#include "am33xx.dtsi"
|
||||
#include "am335x-osd335x-common.dtsi"
|
||||
|
||||
/ {
|
||||
model = "TI AM335x PocketBeagle";
|
||||
compatible = "ti,am335x-pocketbeagle", "ti,am335x-bone", "ti,am33xx";
|
||||
|
||||
chosen {
|
||||
stdout-path = &uart0;
|
||||
};
|
||||
|
||||
leds {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usr_leds_pins>;
|
||||
|
||||
compatible = "gpio-leds";
|
||||
|
||||
usr0 {
|
||||
label = "beaglebone:green:usr0";
|
||||
gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
usr1 {
|
||||
label = "beaglebone:green:usr1";
|
||||
gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "mmc0";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
usr2 {
|
||||
label = "beaglebone:green:usr2";
|
||||
gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "cpu0";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
usr3 {
|
||||
label = "beaglebone:green:usr3";
|
||||
gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
||||
vmmcsd_fixed: fixedregulator0 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vmmcsd_fixed";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
};
|
||||
};
|
||||
|
||||
&am33xx_pinmux {
|
||||
i2c2_pins: pinmux-i2c2-pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE3) /* (D17) uart1_rtsn.I2C2_SCL */
|
||||
AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3) /* (D18) uart1_ctsn.I2C2_SDA */
|
||||
>;
|
||||
};
|
||||
|
||||
ehrpwm0_pins: pinmux-ehrpwm0-pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* (A13) mcasp0_aclkx.ehrpwm0A */
|
||||
>;
|
||||
};
|
||||
|
||||
ehrpwm1_pins: pinmux-ehrpwm1-pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* (U14) gpmc_a2.ehrpwm1A */
|
||||
>;
|
||||
};
|
||||
|
||||
mmc0_pins: pinmux-mmc0-pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* (C15) spi0_cs1.gpio0[6] */
|
||||
AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* (G16) mmc0_dat0.mmc0_dat0 */
|
||||
AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* (G15) mmc0_dat1.mmc0_dat1 */
|
||||
AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* (F18) mmc0_dat2.mmc0_dat2 */
|
||||
AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* (F17) mmc0_dat3.mmc0_dat3 */
|
||||
AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* (G18) mmc0_cmd.mmc0_cmd */
|
||||
AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* (G17) mmc0_clk.mmc0_clk */
|
||||
AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* (B12) mcasp0_aclkr.mmc0_sdwp */
|
||||
>;
|
||||
};
|
||||
|
||||
spi0_pins: pinmux-spi0-pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE0) /* (A17) spi0_sclk.spi0_sclk */
|
||||
AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE0) /* (B17) spi0_d0.spi0_d0 */
|
||||
AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0) /* (B16) spi0_d1.spi0_d1 */
|
||||
AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE0) /* (A16) spi0_cs0.spi0_cs0 */
|
||||
>;
|
||||
};
|
||||
|
||||
spi1_pins: pinmux-spi1-pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x964, PIN_INPUT_PULLUP | MUX_MODE4) /* (C18) eCAP0_in_PWM0_out.spi1_sclk */
|
||||
AM33XX_IOPAD(0x968, PIN_INPUT_PULLUP | MUX_MODE4) /* (E18) uart0_ctsn.spi1_d0 */
|
||||
AM33XX_IOPAD(0x96c, PIN_INPUT_PULLUP | MUX_MODE4) /* (E17) uart0_rtsn.spi1_d1 */
|
||||
AM33XX_IOPAD(0x9b0, PIN_INPUT_PULLUP | MUX_MODE4) /* (A15) xdma_event_intr0.spi1_cs1 */
|
||||
>;
|
||||
};
|
||||
|
||||
usr_leds_pins: pinmux-usr-leds-pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE7) /* (V15) gpmc_a5.gpio1[21] - USR_LED_0 */
|
||||
AM33XX_IOPAD(0x858, PIN_OUTPUT | MUX_MODE7) /* (U15) gpmc_a6.gpio1[22] - USR_LED_1 */
|
||||
AM33XX_IOPAD(0x85c, PIN_OUTPUT | MUX_MODE7) /* (T15) gpmc_a7.gpio1[23] - USR_LED_2 */
|
||||
AM33XX_IOPAD(0x860, PIN_OUTPUT | MUX_MODE7) /* (V16) gpmc_a8.gpio1[24] - USR_LED_3 */
|
||||
>;
|
||||
};
|
||||
|
||||
uart0_pins: pinmux-uart0-pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* (E15) uart0_rxd.uart0_rxd */
|
||||
AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* (E16) uart0_txd.uart0_txd */
|
||||
>;
|
||||
};
|
||||
|
||||
uart4_pins: pinmux-uart4-pins {
|
||||
pinctrl-single,pins = <
|
||||
AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE6) /* (T17) gpmc_wait0.uart4_rxd */
|
||||
AM33XX_IOPAD(0x874, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* (U17) gpmc_wpn.uart4_txd */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
&epwmss0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ehrpwm0 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ehrpwm0_pins>;
|
||||
};
|
||||
|
||||
&epwmss1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ehrpwm1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ehrpwm1_pins>;
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
eeprom: eeprom@50 {
|
||||
compatible = "atmel,24c256";
|
||||
reg = <0x50>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c2_pins>;
|
||||
|
||||
status = "okay";
|
||||
clock-frequency = <400000>;
|
||||
};
|
||||
|
||||
&mmc1 {
|
||||
status = "okay";
|
||||
vmmc-supply = <&vmmcsd_fixed>;
|
||||
bus-width = <4>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mmc0_pins>;
|
||||
cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&rtc {
|
||||
system-power-controller;
|
||||
};
|
||||
|
||||
&tscadc {
|
||||
status = "okay";
|
||||
adc {
|
||||
ti,adc-channels = <0 1 2 3 4 5 6 7>;
|
||||
ti,chan-step-avg = <16 16 16 16 16 16 16 16>;
|
||||
ti,chan-step-opendelay = <0x98 0x98 0x98 0x98 0x98 0x98 0x98 0x98>;
|
||||
ti,chan-step-sampledelay = <0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0>;
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart0_pins>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart4 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart4_pins>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_ctrl_mod {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
dr_mode = "otg";
|
||||
};
|
||||
|
||||
&usb1_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb1 {
|
||||
status = "okay";
|
||||
dr_mode = "host";
|
||||
};
|
||||
|
||||
&cppi41dma {
|
||||
status = "okay";
|
||||
};
|
||||
@ -8,11 +8,17 @@
|
||||
/dts-v1/;
|
||||
|
||||
#include "am3517.dtsi"
|
||||
#include "am3517-som.dtsi"
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "TI AM3517 EVM (AM3517/05 TMDSEVM3517)";
|
||||
compatible = "ti,am3517-evm", "ti,am3517", "ti,omap3";
|
||||
|
||||
aliases {
|
||||
display0 = &lcd0;
|
||||
};
|
||||
|
||||
memory@80000000 {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x10000000>; /* 256 MB */
|
||||
@ -24,6 +30,144 @@
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <100>;
|
||||
|
||||
user_pb {
|
||||
label = "User Push Button";
|
||||
linux,code = <BTN_0>;
|
||||
gpios = <&tca6416 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
user_sw_1 {
|
||||
label = "User Switch 1";
|
||||
linux,code = <BTN_1>;
|
||||
gpios = <&tca6416 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
user_sw_2 {
|
||||
label = "User Switch 2";
|
||||
linux,code = <BTN_2>;
|
||||
gpios = <&tca6416 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
user_sw_3 {
|
||||
label = "User Switch 3";
|
||||
linux,code = <BTN_3>;
|
||||
gpios = <&tca6416 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
user_sw_4 {
|
||||
label = "User Switch 4";
|
||||
linux,code = <BTN_4>;
|
||||
gpios = <&tca6416 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
user_sw_5 {
|
||||
label = "User Switch 5";
|
||||
linux,code = <BTN_5>;
|
||||
gpios = <&tca6416 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
user_sw_6 {
|
||||
label = "User Switch 6";
|
||||
linux,code = <BTN_6>;
|
||||
gpios = <&tca6416 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
user_sw_7 {
|
||||
label = "User Switch 7";
|
||||
linux,code = <BTN_7>;
|
||||
gpios = <&tca6416 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
user_sw_8 {
|
||||
label = "User Switch 8";
|
||||
linux,code = <BTN_8>;
|
||||
gpios = <&tca6416 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&leds_pins>;
|
||||
|
||||
user_led_1 {
|
||||
label = "am3517evm:green:user_led_1";
|
||||
gpios = <&tca6416 7 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
user_led_2 {
|
||||
label = "am3517evm:green:user_led_2";
|
||||
gpios = <&tca6416 6 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
user_led_3 {
|
||||
label = "am3517evm:green:user_led_3";
|
||||
gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "mmc0"; /* SD/MMC card activity */
|
||||
};
|
||||
|
||||
user_led_4 {
|
||||
label = "am3517evm:green:user_led_4";
|
||||
gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
};
|
||||
};
|
||||
|
||||
lcd0: display@0 {
|
||||
compatible = "panel-dpi";
|
||||
label = "15";
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
enable-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>; /* gpio176, lcd INI */
|
||||
|
||||
port {
|
||||
lcd_in: endpoint {
|
||||
remote-endpoint = <&dpi_out>;
|
||||
};
|
||||
};
|
||||
|
||||
panel-timing {
|
||||
clock-frequency = <9000000>;
|
||||
hactive = <480>;
|
||||
vactive = <272>;
|
||||
hfront-porch = <3>;
|
||||
hback-porch = <2>;
|
||||
hsync-len = <42>;
|
||||
vback-porch = <3>;
|
||||
vfront-porch = <4>;
|
||||
vsync-len = <11>;
|
||||
hsync-active = <0>;
|
||||
vsync-active = <0>;
|
||||
de-active = <1>;
|
||||
pixelclk-active = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
bl: backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&backlight_pins>;
|
||||
pwms = <&pwm11 0 5000000 0>;
|
||||
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
|
||||
default-brightness-level = <7>;
|
||||
enable-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* gpio_182 */
|
||||
};
|
||||
|
||||
pwm11: dmtimer-pwm@11 {
|
||||
compatible = "ti,omap-dmtimer-pwm";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm_pins>;
|
||||
ti,timers = <&timer11>;
|
||||
#pwm-cells = <3>;
|
||||
};
|
||||
};
|
||||
|
||||
&davinci_emac {
|
||||
@ -34,12 +178,32 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
clock-frequency = <400000>;
|
||||
&dss {
|
||||
status = "ok";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&dss_dpi_pins>;
|
||||
|
||||
vdds_dsi-supply = <&vdd_io_reg>;
|
||||
vdda_video-supply = <&vdd_io_reg>;
|
||||
|
||||
port {
|
||||
dpi_out: endpoint {
|
||||
remote-endpoint = <&lcd_in>;
|
||||
data-lines = <16>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
clock-frequency = <400000>;
|
||||
/* User DIP swithes [1:8] / User LEDS [1:2] */
|
||||
tca6416: gpio@21 {
|
||||
compatible = "ti,tca6416";
|
||||
reg = <0x21>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c3 {
|
||||
@ -47,8 +211,13 @@
|
||||
};
|
||||
|
||||
&mmc1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mmc1_pins>;
|
||||
vmmc-supply = <&vmmc_fixed>;
|
||||
bus-width = <4>;
|
||||
wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>; /* gpio_126 */
|
||||
cd-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio_127 */
|
||||
};
|
||||
|
||||
&mmc2 {
|
||||
@ -59,3 +228,63 @@
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&omap3_pmx_core {
|
||||
|
||||
leds_pins: pinmux_leds_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 */
|
||||
OMAP3_WKUP_IOPAD(0x2a26, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu1.gpio_31 */
|
||||
>;
|
||||
};
|
||||
|
||||
mmc1_pins: pinmux_mmc1_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
|
||||
OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
|
||||
OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
|
||||
OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
|
||||
OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
|
||||
OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
|
||||
OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE4) /* sdmmc1_dat4.gpio_126 */
|
||||
OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE4) /* sdmmc1_dat5.gpio_127 */
|
||||
>;
|
||||
};
|
||||
|
||||
pwm_pins: pinmux_pwm_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP3_CORE1_IOPAD(0x21dc, PIN_OUTPUT | MUX_MODE1) /* mcspi2_cs0.gpt11_pwm */
|
||||
>;
|
||||
};
|
||||
|
||||
backlight_pins: pinmux_backlight_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP3_CORE1_IOPAD(0x21de, PIN_OUTPUT | MUX_MODE4) /* mcspi2_cs1.gpio_182 */
|
||||
>;
|
||||
};
|
||||
|
||||
dss_dpi_pins: pinmux_dss_dpi_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP3_CORE1_IOPAD(0x21d2, PIN_OUTPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
|
||||
OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
|
||||
OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
|
||||
OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
|
||||
OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
|
||||
OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */
|
||||
OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */
|
||||
OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */
|
||||
OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */
|
||||
OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */
|
||||
OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */
|
||||
OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
|
||||
OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
|
||||
OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
|
||||
OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
|
||||
OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
|
||||
OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
|
||||
OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
|
||||
OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
|
||||
OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
|
||||
OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
142
arch/arm/boot/dts/am3517-som.dtsi
Normal file
142
arch/arm/boot/dts/am3517-som.dtsi
Normal file
@ -0,0 +1,142 @@
|
||||
/*
|
||||
* Copyright (C) 2016 Derald D. Woods <woods.technical@gmail.com>
|
||||
*
|
||||
* Based on am3517-evm.dts
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
/ {
|
||||
cpus {
|
||||
cpu@0 {
|
||||
cpu0-supply = <&vdd_core_reg>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpmc {
|
||||
ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
|
||||
|
||||
nand@0,0 {
|
||||
compatible = "ti,omap2-nand";
|
||||
linux,mtd-name = "micron,mt29f4g16abchch";
|
||||
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
|
||||
nand-bus-width = <16>;
|
||||
ti,nand-ecc-opt = "bch8";
|
||||
gpmc,sync-clk-ps = <0>;
|
||||
gpmc,cs-on-ns = <0>;
|
||||
gpmc,cs-rd-off-ns = <44>;
|
||||
gpmc,cs-wr-off-ns = <44>;
|
||||
gpmc,adv-on-ns = <6>;
|
||||
gpmc,adv-rd-off-ns = <34>;
|
||||
gpmc,adv-wr-off-ns = <44>;
|
||||
gpmc,we-off-ns = <40>;
|
||||
gpmc,oe-off-ns = <54>;
|
||||
gpmc,access-ns = <64>;
|
||||
gpmc,rd-cycle-ns = <82>;
|
||||
gpmc,wr-cycle-ns = <82>;
|
||||
gpmc,wr-access-ns = <40>;
|
||||
gpmc,wr-data-mux-bus-ns = <0>;
|
||||
gpmc,device-width = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
clock-frequency = <400000>;
|
||||
|
||||
s35390a: s35390a@30 {
|
||||
compatible = "sii,s35390a";
|
||||
reg = <0x30>;
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rtc_pins>;
|
||||
interrupts-extended = <&gpio2 23 IRQ_TYPE_EDGE_FALLING>; /* gpio_55 */
|
||||
};
|
||||
|
||||
tps: tps65023@48 {
|
||||
compatible = "ti,tps65023";
|
||||
reg = <0x48>;
|
||||
|
||||
regulators {
|
||||
vdd_core_reg: VDCDC1 {
|
||||
regulator-name = "vdd_core";
|
||||
compatible = "regulator-fixed";
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
};
|
||||
|
||||
vdd_io_reg: VDCDC2 {
|
||||
regulator-name = "vdd_io";
|
||||
compatible = "regulator-fixed";
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
};
|
||||
|
||||
vdd_1v8_reg: VDCDC3 {
|
||||
regulator-name = "vdd_1v8";
|
||||
compatible = "regulator-fixed";
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
|
||||
vdd_usb18_reg: LDO1 {
|
||||
regulator-name = "vdd_usb18";
|
||||
compatible = "regulator-fixed";
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
|
||||
vdd_usb33_reg: LDO2 {
|
||||
regulator-name = "vdd_usb33";
|
||||
compatible = "regulator-fixed";
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
touchscreen: tsc2004@4b {
|
||||
compatible = "ti,tsc2004";
|
||||
reg = <0x4b>;
|
||||
|
||||
vio-supply = <&vdd_io_reg>;
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&tsc2004_pins>;
|
||||
interrupts-extended = <&gpio3 1 IRQ_TYPE_EDGE_RISING>; /* gpio_65 */
|
||||
|
||||
touchscreen-fuzz-x = <4>;
|
||||
touchscreen-fuzz-y = <7>;
|
||||
touchscreen-fuzz-pressure = <2>;
|
||||
touchscreen-size-x = <480>;
|
||||
touchscreen-size-y = <272>;
|
||||
touchscreen-max-pressure = <2048>;
|
||||
|
||||
ti,x-plate-ohms = <280>;
|
||||
ti,esd-recovery-timeout-ms = <8000>;
|
||||
};
|
||||
};
|
||||
|
||||
&omap3_pmx_core {
|
||||
|
||||
rtc_pins: pinmux_rtc_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP3_CORE1_IOPAD(0x20b6, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_ncs4.gpio_55 */
|
||||
>;
|
||||
};
|
||||
|
||||
tsc2004_pins: pinmux_tsc2004_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT | MUX_MODE4) /* gpmc_wait3.gpio_65 */
|
||||
>;
|
||||
};
|
||||
};
|
||||
@ -203,7 +203,7 @@
|
||||
tps65218: tps65218@24 {
|
||||
compatible = "ti,tps65218";
|
||||
reg = <0x24>;
|
||||
interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* NMIn */
|
||||
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* NMIn */
|
||||
interrupt-parent = <&gic>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
|
||||
@ -543,7 +543,7 @@
|
||||
tps65218: tps65218@24 {
|
||||
reg = <0x24>;
|
||||
compatible = "ti,tps65218";
|
||||
interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* NMIn */
|
||||
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* NMIn */
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
|
||||
|
||||
@ -15,6 +15,7 @@
|
||||
#include <dt-bindings/pwm/pwm.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
|
||||
/ {
|
||||
model = "TI AM437x SK EVM";
|
||||
@ -158,6 +159,22 @@
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
vmmcwl_fixed: fixedregulator-mmcwl {
|
||||
/*
|
||||
* WL_EN is not SDIO standard compliant. It is an out of band
|
||||
* signal and hard to be dealt with in a standard way by the
|
||||
* SDIO core driver.
|
||||
* So modelling the WL_EN line as a regulator was a natural
|
||||
* choice as the MMC core already deals with MMC supplies.
|
||||
*/
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vmmcwl_fixed";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
};
|
||||
};
|
||||
|
||||
&am43xx_pinmux {
|
||||
@ -418,6 +435,62 @@
|
||||
AM4372_IOPAD(0xac4, PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */
|
||||
>;
|
||||
};
|
||||
|
||||
mmc3_pins_default: pinmux_mmc3_pins_default {
|
||||
pinctrl-single,pins = <
|
||||
AM4372_IOPAD(0x9f0, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD21) cam1_data2.mmc2_clk */
|
||||
AM4372_IOPAD(0x9f4, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE22) cam1_data3.mmc2_cmd */
|
||||
AM4372_IOPAD(0x9f8, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD22) cam1_data4.mmc2_dat0 */
|
||||
AM4372_IOPAD(0x9fc, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE23) cam1_data5.mmc2_dat1 */
|
||||
AM4372_IOPAD(0xa00, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD23) cam1_data6.mmc2_dat2 */
|
||||
AM4372_IOPAD(0xa04, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE24) cam1_data7.mmc2_dat3 */
|
||||
>;
|
||||
};
|
||||
|
||||
mmc3_pins_sleep: pinmux_mmc3_pins_sleep {
|
||||
pinctrl-single,pins = <
|
||||
AM4372_IOPAD(0x9f0, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD21) cam1_data2.mmc2_clk */
|
||||
AM4372_IOPAD(0x9f4, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE22) cam1_data3.mmc2_cmd */
|
||||
AM4372_IOPAD(0x9f8, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD22) cam1_data4.mmc2_dat0 */
|
||||
AM4372_IOPAD(0x9fc, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE23) cam1_data5.mmc2_dat1 */
|
||||
AM4372_IOPAD(0xa00, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD23) cam1_data6.mmc2_dat2 */
|
||||
AM4372_IOPAD(0xa04, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE24) cam1_data7.mmc2_dat3 */
|
||||
>;
|
||||
};
|
||||
|
||||
wlan_pins_default: pinmux_wlan_pins_default {
|
||||
pinctrl-single,pins = <
|
||||
AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data8.gpio4_8 WL_EN */
|
||||
AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* cam1_wen.gpio4_13 WL_IRQ */
|
||||
>;
|
||||
};
|
||||
|
||||
wlan_pins_sleep: pinmux_wlan_pins_sleep {
|
||||
pinctrl-single,pins = <
|
||||
AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data8.gpio4_8 WL_EN */
|
||||
AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* cam1_wen.gpio4_13 WL_IRQ */
|
||||
>;
|
||||
};
|
||||
|
||||
uart1_bt_pins_default: pinmux_uart1_bt_pins_default {
|
||||
pinctrl-single,pins = <
|
||||
AM4372_IOPAD(0x980, PIN_INPUT | MUX_MODE0) /* uart1_rxd.uart1_rxd */
|
||||
AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */
|
||||
AM4372_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */
|
||||
AM4372_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */
|
||||
AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data9.gpio4_7 BT_EN */
|
||||
>;
|
||||
};
|
||||
|
||||
uart1_bt_pins_sleep: pinmux_uart1_bt_pins_sleep {
|
||||
pinctrl-single,pins = <
|
||||
AM4372_IOPAD(0x980, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rxd.uart1_rxd */
|
||||
AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_txd.uart1_txd */
|
||||
AM4372_IOPAD(0x978, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */
|
||||
AM4372_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */
|
||||
AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLUP | MUX_MODE7) /* cam1_data9.gpio4_7 BT_EN */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
@ -581,6 +654,10 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio4 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio5 {
|
||||
status = "okay";
|
||||
};
|
||||
@ -595,6 +672,44 @@
|
||||
cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&uart1_bt_pins_default>;
|
||||
pinctrl-1 = <&uart1_bt_pins_sleep>;
|
||||
};
|
||||
|
||||
&mmc3 {
|
||||
status = "okay";
|
||||
/*
|
||||
* these are on the crossbar and are outlined in the
|
||||
* xbar-event-map element
|
||||
*/
|
||||
dmas = <&edma_xbar 30 0 1>,
|
||||
<&edma_xbar 31 0 2>;
|
||||
dma-names = "tx", "rx";
|
||||
vmmc-supply = <&vmmcwl_fixed>;
|
||||
bus-width = <4>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&mmc3_pins_default>;
|
||||
pinctrl-1 = <&mmc3_pins_sleep>;
|
||||
cap-power-off-card;
|
||||
keep-power-in-suspend;
|
||||
ti,non-removable;
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
wlcore: wlcore@2 {
|
||||
compatible = "ti,wl1835";
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&wlan_pins_default>;
|
||||
pinctrl-1 = <&wlan_pins_sleep>;
|
||||
reg = <2>;
|
||||
interrupt-parent = <&gpio4>;
|
||||
interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&usb2_phy1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -595,7 +595,7 @@
|
||||
tps65218: tps65218@24 {
|
||||
reg = <0x24>;
|
||||
compatible = "ti,tps65218";
|
||||
interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* NMIn */
|
||||
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* NMIn */
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
|
||||
|
||||
@ -10,6 +10,7 @@
|
||||
#include "dra72x.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
#include "dra7-mmc-iodelay.dtsi"
|
||||
#include "dra72x-mmc-iodelay.dtsi"
|
||||
#include "am57xx-idk-common.dtsi"
|
||||
|
||||
@ -102,7 +103,7 @@
|
||||
|
||||
&mmc1 {
|
||||
pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
|
||||
pinctrl-0 = <&mmc1_pins_default>;
|
||||
pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
|
||||
pinctrl-1 = <&mmc1_pins_hs>;
|
||||
pinctrl-2 = <&mmc1_pins_sdr12>;
|
||||
pinctrl-3 = <&mmc1_pins_sdr25>;
|
||||
@ -112,7 +113,7 @@
|
||||
};
|
||||
|
||||
&mmc2 {
|
||||
pinctrl-names = "default", "hs", "ddr_1_8v";
|
||||
pinctrl-names = "default", "hs", "ddr_3_3v";
|
||||
pinctrl-0 = <&mmc2_pins_default>;
|
||||
pinctrl-1 = <&mmc2_pins_hs>;
|
||||
pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
|
||||
|
||||
@ -9,6 +9,7 @@
|
||||
/dts-v1/;
|
||||
|
||||
#include "dra74x.dtsi"
|
||||
#include "dra7-mmc-iodelay.dtsi"
|
||||
#include "dra74x-mmc-iodelay.dtsi"
|
||||
#include "am572x-idk-common.dtsi"
|
||||
|
||||
@ -20,7 +21,7 @@
|
||||
|
||||
&mmc1 {
|
||||
pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
|
||||
pinctrl-0 = <&mmc1_pins_default>;
|
||||
pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
|
||||
pinctrl-1 = <&mmc1_pins_hs>;
|
||||
pinctrl-2 = <&mmc1_pins_sdr12>;
|
||||
pinctrl-3 = <&mmc1_pins_sdr25>;
|
||||
@ -30,7 +31,7 @@
|
||||
};
|
||||
|
||||
&mmc2 {
|
||||
pinctrl-names = "default", "hs", "ddr_1_8v";
|
||||
pinctrl-names = "default", "hs", "ddr_3_3v";
|
||||
pinctrl-0 = <&mmc2_pins_default>;
|
||||
pinctrl-1 = <&mmc2_pins_hs>;
|
||||
pinctrl-2 = <&mmc2_pins_ddr_rev20>;
|
||||
|
||||
@ -7,6 +7,8 @@
|
||||
/dts-v1/;
|
||||
|
||||
#include "dra76x.dtsi"
|
||||
#include "dra7-mmc-iodelay.dtsi"
|
||||
#include "dra76x-mmc-iodelay.dtsi"
|
||||
#include "am572x-idk-common.dtsi"
|
||||
|
||||
/ {
|
||||
@ -20,3 +22,21 @@
|
||||
spi-max-frequency = <96000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&mmc1 {
|
||||
pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
|
||||
pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
|
||||
pinctrl-1 = <&mmc1_pins_hs>;
|
||||
pinctrl-2 = <&mmc1_pins_default>;
|
||||
pinctrl-3 = <&mmc1_pins_hs>;
|
||||
pinctrl-4 = <&mmc1_pins_sdr50>;
|
||||
pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_conf>;
|
||||
pinctrl-6 = <&mmc1_pins_ddr50 &mmc1_iodelay_sdr104_conf>;
|
||||
};
|
||||
|
||||
&mmc2 {
|
||||
pinctrl-names = "default", "hs", "ddr_3_3v";
|
||||
pinctrl-0 = <&mmc2_pins_default>;
|
||||
pinctrl-1 = <&mmc2_pins_default>;
|
||||
pinctrl-2 = <&mmc2_pins_default>;
|
||||
};
|
||||
|
||||
@ -444,8 +444,8 @@
|
||||
vmmc-supply = <&vdd_3v3>;
|
||||
vqmmc-supply = <&vdd_3v3>;
|
||||
bus-width = <8>;
|
||||
ti,non-removable;
|
||||
cap-mmc-dual-data-rate;
|
||||
non-removable;
|
||||
no-1-8-v;
|
||||
};
|
||||
|
||||
&sata {
|
||||
|
||||
@ -25,10 +25,11 @@
|
||||
pinctrl-1 = <&mmc1_pins_hs>;
|
||||
|
||||
vmmc-supply = <&ldo1_reg>;
|
||||
no-1-8-v;
|
||||
};
|
||||
|
||||
&mmc2 {
|
||||
pinctrl-names = "default", "hs", "ddr_1_8v";
|
||||
pinctrl-names = "default", "hs", "ddr_3_3v";
|
||||
pinctrl-0 = <&mmc2_pins_default>;
|
||||
pinctrl-1 = <&mmc2_pins_hs>;
|
||||
pinctrl-2 = <&mmc2_pins_ddr_3_3v_rev11 &mmc2_iodelay_ddr_3_3v_rev11_conf>;
|
||||
|
||||
@ -115,17 +115,6 @@
|
||||
DRA7XX_CORE_IOPAD(0x37d4, MUX_MODE15 | PULL_UP) /* dcan1_rx.off */
|
||||
>;
|
||||
};
|
||||
|
||||
mmc1_pins_default: mmc1_pins_default {
|
||||
pinctrl-single,pins = <
|
||||
DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mmc1_clk.clk */
|
||||
DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
|
||||
DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
|
||||
DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
|
||||
DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
|
||||
DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
@ -423,8 +412,9 @@
|
||||
vmmc-supply = <&v3_3d>;
|
||||
vqmmc-supply = <&v3_3d>;
|
||||
bus-width = <8>;
|
||||
ti,non-removable;
|
||||
non-removable;
|
||||
max-frequency = <96000000>;
|
||||
no-1-8-v;
|
||||
};
|
||||
|
||||
&dcan1 {
|
||||
|
||||
@ -105,33 +105,6 @@
|
||||
usb@51000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -239,3 +212,33 @@
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -44,61 +44,6 @@
|
||||
usb@50000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
/* 1.0 MiB */
|
||||
reg = <0x0000000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
/* 128 KiB */
|
||||
reg = <0x100000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@120000 {
|
||||
label = "uImage";
|
||||
/* 7 MiB */
|
||||
reg = <0x120000 0x700000>;
|
||||
};
|
||||
|
||||
partition@820000 {
|
||||
label = "ubifs";
|
||||
/* ~ 84 MiB */
|
||||
reg = <0x820000 0x54e0000>;
|
||||
};
|
||||
|
||||
/* Hardcoded into stock bootloader */
|
||||
partition@5d00000 {
|
||||
label = "failsafe-uImage";
|
||||
/* 5 MiB */
|
||||
reg = <0x5d00000 0x500000>;
|
||||
};
|
||||
|
||||
partition@6200000 {
|
||||
label = "failsafe-fs";
|
||||
/* 29 MiB */
|
||||
reg = <0x6200000 0x1d00000>;
|
||||
};
|
||||
|
||||
partition@7f00000 {
|
||||
label = "bbt";
|
||||
/* 1 MiB for BBT */
|
||||
reg = <0x7f00000 0x100000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -319,3 +264,68 @@
|
||||
clock-frequency = <100000>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
/* 1.0 MiB */
|
||||
reg = <0x0000000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
/* 128 KiB */
|
||||
reg = <0x100000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@120000 {
|
||||
label = "uImage";
|
||||
/* 7 MiB */
|
||||
reg = <0x120000 0x700000>;
|
||||
};
|
||||
|
||||
partition@820000 {
|
||||
label = "ubifs";
|
||||
/* ~ 84 MiB */
|
||||
reg = <0x820000 0x54e0000>;
|
||||
};
|
||||
|
||||
/* Hardcoded into stock bootloader */
|
||||
partition@5d00000 {
|
||||
label = "failsafe-uImage";
|
||||
/* 5 MiB */
|
||||
reg = <0x5d00000 0x500000>;
|
||||
};
|
||||
|
||||
partition@6200000 {
|
||||
label = "failsafe-fs";
|
||||
/* 29 MiB */
|
||||
reg = <0x6200000 0x1d00000>;
|
||||
};
|
||||
|
||||
partition@7f00000 {
|
||||
label = "bbt";
|
||||
/* 1 MiB for BBT */
|
||||
reg = <0x7f00000 0x100000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -108,27 +108,6 @@
|
||||
reg = <0x25>;
|
||||
};
|
||||
};
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x400000>;
|
||||
};
|
||||
partition@400000 {
|
||||
label = "Linux";
|
||||
reg = <0x400000 0x400000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x800000 0x3f800000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -173,3 +152,33 @@
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x400000>;
|
||||
};
|
||||
partition@400000 {
|
||||
label = "Linux";
|
||||
reg = <0x400000 0x400000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x800000 0x3f800000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -81,46 +81,6 @@
|
||||
pwm_polarity = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
/* Use Hardware BCH ECC */
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x180000>; /* 1.5MB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x180000 0x20000>; /* 128KB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "uImage";
|
||||
reg = <0x0200000 0x600000>; /* 6MB */
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "minirootfs";
|
||||
reg = <0x0800000 0x400000>; /* 4MB */
|
||||
};
|
||||
|
||||
/* Last MB is for the BBT, i.e. not writable */
|
||||
partition@c00000 {
|
||||
label = "ubifs";
|
||||
reg = <0x0c00000 0x7400000>; /* 116MB */
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -264,3 +224,53 @@
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
/* Use Hardware BCH ECC */
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x180000>; /* 1.5MB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x180000 0x20000>; /* 128KB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "uImage";
|
||||
reg = <0x0200000 0x600000>; /* 6MB */
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "minirootfs";
|
||||
reg = <0x0800000 0x400000>; /* 4MB */
|
||||
};
|
||||
|
||||
/* Last MB is for the BBT, i.e. not writable */
|
||||
partition@c00000 {
|
||||
label = "ubifs";
|
||||
reg = <0x0c00000 0x7400000>; /* 116MB */
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -90,46 +90,6 @@
|
||||
reg = <0x23>;
|
||||
};
|
||||
};
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
/* Use Hardware BCH ECC */
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x180000>; /* 1.5MB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x180000 0x20000>; /* 128KB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "uImage";
|
||||
reg = <0x0200000 0x600000>; /* 6MB */
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "minirootfs";
|
||||
reg = <0x0800000 0x400000>; /* 4MB */
|
||||
};
|
||||
|
||||
/* Last MB is for the BBT, i.e. not writable */
|
||||
partition@c00000 {
|
||||
label = "ubifs";
|
||||
reg = <0x0c00000 0x7400000>; /* 116MB */
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -276,3 +236,53 @@
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
/* Use Hardware BCH ECC */
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x180000>; /* 1.5MB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x180000 0x20000>; /* 128KB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "uImage";
|
||||
reg = <0x0200000 0x600000>; /* 6MB */
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "minirootfs";
|
||||
reg = <0x0800000 0x400000>; /* 4MB */
|
||||
};
|
||||
|
||||
/* Last MB is for the BBT, i.e. not writable */
|
||||
partition@c00000 {
|
||||
label = "ubifs";
|
||||
reg = <0x0c00000 0x7400000>; /* 116MB */
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -112,27 +112,6 @@
|
||||
default-state = "keep";
|
||||
};
|
||||
};
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -288,3 +267,34 @@
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -66,33 +66,6 @@
|
||||
interrupts = <110>;
|
||||
};
|
||||
};
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x300000>;
|
||||
};
|
||||
partition@300000 {
|
||||
label = "device-tree";
|
||||
reg = <0x300000 0x20000>;
|
||||
};
|
||||
partition@320000 {
|
||||
label = "linux";
|
||||
reg = <0x320000 0x2000000>;
|
||||
};
|
||||
partition@2320000 {
|
||||
label = "rootfs";
|
||||
reg = <0x2320000 0xdce0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
@ -227,3 +200,40 @@
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x300000>;
|
||||
};
|
||||
partition@300000 {
|
||||
label = "device-tree";
|
||||
reg = <0x300000 0x20000>;
|
||||
};
|
||||
partition@320000 {
|
||||
label = "linux";
|
||||
reg = <0x320000 0x2000000>;
|
||||
};
|
||||
partition@2320000 {
|
||||
label = "rootfs";
|
||||
reg = <0x2320000 0xdce0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -244,11 +244,11 @@
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
nand: nand@d0000 {
|
||||
compatible = "marvell,armada370-nand";
|
||||
nand_controller: nand-controller@d0000 {
|
||||
compatible = "marvell,armada370-nand-controller";
|
||||
reg = <0xd0000 0x54>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
interrupts = <113>;
|
||||
clocks = <&coredivclk 0>;
|
||||
status = "disabled";
|
||||
|
||||
@ -103,28 +103,38 @@
|
||||
nr-ports = <2>;
|
||||
};
|
||||
|
||||
&nand {
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
@ -502,11 +502,11 @@
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
nand: nand@d0000 {
|
||||
compatible = "marvell,armada370-nand";
|
||||
nand_controller: nand-controller@d0000 {
|
||||
compatible = "marvell,armada370-nand-controller";
|
||||
reg = <0xd0000 0x54>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&gateclk 11>;
|
||||
status = "disabled";
|
||||
|
||||
@ -135,39 +135,6 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
nfc: flash@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0x00000000 0x00800000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "uImage";
|
||||
reg = <0x00800000 0x00400000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c00000 {
|
||||
label = "Root";
|
||||
reg = <0x00c00000 0x3f400000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb3@f0000 {
|
||||
status = "okay";
|
||||
usb-phy = <&usb3_phy>;
|
||||
@ -233,3 +200,39 @@
|
||||
spi-max-frequency = <54000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0x00000000 0x00800000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "uImage";
|
||||
reg = <0x00800000 0x00400000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c00000 {
|
||||
label = "Root";
|
||||
reg = <0x00c00000 0x3f400000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -73,67 +73,72 @@
|
||||
|
||||
&nand {
|
||||
/* 128MiB */
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x200000>; /* 2MiB */
|
||||
read-only;
|
||||
};
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x200000>; /* 2MiB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u_env";
|
||||
reg = <0x200000 0x40000>; /* 256KiB */
|
||||
};
|
||||
partition@100000 {
|
||||
label = "u_env";
|
||||
reg = <0x200000 0x40000>; /* 256KiB */
|
||||
};
|
||||
|
||||
partition@140000 {
|
||||
label = "s_env";
|
||||
reg = <0x240000 0x40000>; /* 256KiB */
|
||||
};
|
||||
partition@140000 {
|
||||
label = "s_env";
|
||||
reg = <0x240000 0x40000>; /* 256KiB */
|
||||
};
|
||||
|
||||
partition@900000 {
|
||||
label = "devinfo";
|
||||
reg = <0x900000 0x100000>; /* 1MiB */
|
||||
read-only;
|
||||
};
|
||||
partition@900000 {
|
||||
label = "devinfo";
|
||||
reg = <0x900000 0x100000>; /* 1MiB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* kernel1 overlaps with rootfs1 by design */
|
||||
partition@a00000 {
|
||||
label = "kernel1";
|
||||
reg = <0xa00000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
/* kernel1 overlaps with rootfs1 by design */
|
||||
partition@a00000 {
|
||||
label = "kernel1";
|
||||
reg = <0xa00000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
|
||||
partition@1000000 {
|
||||
label = "rootfs1";
|
||||
reg = <0x1000000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "rootfs1";
|
||||
reg = <0x1000000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
|
||||
/* kernel2 overlaps with rootfs2 by design */
|
||||
partition@3200000 {
|
||||
label = "kernel2";
|
||||
reg = <0x3200000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
/* kernel2 overlaps with rootfs2 by design */
|
||||
partition@3200000 {
|
||||
label = "kernel2";
|
||||
reg = <0x3200000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
|
||||
partition@3800000 {
|
||||
label = "rootfs2";
|
||||
reg = <0x3800000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
partition@3800000 {
|
||||
label = "rootfs2";
|
||||
reg = <0x3800000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
|
||||
/*
|
||||
* 38MiB, last MiB is for the BBT, not writable
|
||||
*/
|
||||
partition@5a00000 {
|
||||
label = "syscfg";
|
||||
reg = <0x5a00000 0x2600000>;
|
||||
};
|
||||
/*
|
||||
* 38MiB, last MiB is for the BBT, not writable
|
||||
*/
|
||||
partition@5a00000 {
|
||||
label = "syscfg";
|
||||
reg = <0x5a00000 0x2600000>;
|
||||
};
|
||||
|
||||
/*
|
||||
* Unused area between "s_env" and "devinfo".
|
||||
* Moved here because otherwise the renumbered
|
||||
* partitions would break the bootloader
|
||||
* supplied bootargs
|
||||
*/
|
||||
partition@180000 {
|
||||
label = "unused_area";
|
||||
reg = <0x280000 0x680000>; /* 6.5MiB */
|
||||
/*
|
||||
* Unused area between "s_env" and "devinfo".
|
||||
* Moved here because otherwise the renumbered
|
||||
* partitions would break the bootloader
|
||||
* supplied bootargs
|
||||
*/
|
||||
partition@180000 {
|
||||
label = "unused_area";
|
||||
reg = <0x280000 0x680000>; /* 6.5MiB */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -73,67 +73,72 @@
|
||||
|
||||
&nand {
|
||||
/* 128MiB */
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x200000>; /* 2MiB */
|
||||
read-only;
|
||||
};
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x200000>; /* 2MiB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u_env";
|
||||
reg = <0x200000 0x40000>; /* 256KiB */
|
||||
};
|
||||
partition@100000 {
|
||||
label = "u_env";
|
||||
reg = <0x200000 0x40000>; /* 256KiB */
|
||||
};
|
||||
|
||||
partition@140000 {
|
||||
label = "s_env";
|
||||
reg = <0x240000 0x40000>; /* 256KiB */
|
||||
};
|
||||
partition@140000 {
|
||||
label = "s_env";
|
||||
reg = <0x240000 0x40000>; /* 256KiB */
|
||||
};
|
||||
|
||||
partition@900000 {
|
||||
label = "devinfo";
|
||||
reg = <0x900000 0x100000>; /* 1MiB */
|
||||
read-only;
|
||||
};
|
||||
partition@900000 {
|
||||
label = "devinfo";
|
||||
reg = <0x900000 0x100000>; /* 1MiB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* kernel1 overlaps with rootfs1 by design */
|
||||
partition@a00000 {
|
||||
label = "kernel1";
|
||||
reg = <0xa00000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
/* kernel1 overlaps with rootfs1 by design */
|
||||
partition@a00000 {
|
||||
label = "kernel1";
|
||||
reg = <0xa00000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
|
||||
partition@1000000 {
|
||||
label = "rootfs1";
|
||||
reg = <0x1000000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "rootfs1";
|
||||
reg = <0x1000000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
|
||||
/* kernel2 overlaps with rootfs2 by design */
|
||||
partition@3200000 {
|
||||
label = "kernel2";
|
||||
reg = <0x3200000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
/* kernel2 overlaps with rootfs2 by design */
|
||||
partition@3200000 {
|
||||
label = "kernel2";
|
||||
reg = <0x3200000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
|
||||
partition@3800000 {
|
||||
label = "rootfs2";
|
||||
reg = <0x3800000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
partition@3800000 {
|
||||
label = "rootfs2";
|
||||
reg = <0x3800000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
|
||||
/*
|
||||
* 38MiB, last MiB is for the BBT, not writable
|
||||
*/
|
||||
partition@5a00000 {
|
||||
label = "syscfg";
|
||||
reg = <0x5a00000 0x2600000>;
|
||||
};
|
||||
/*
|
||||
* 38MiB, last MiB is for the BBT, not writable
|
||||
*/
|
||||
partition@5a00000 {
|
||||
label = "syscfg";
|
||||
reg = <0x5a00000 0x2600000>;
|
||||
};
|
||||
|
||||
/*
|
||||
* Unused area between "s_env" and "devinfo".
|
||||
* Moved here because otherwise the renumbered
|
||||
* partitions would break the bootloader
|
||||
* supplied bootargs
|
||||
*/
|
||||
partition@180000 {
|
||||
label = "unused_area";
|
||||
reg = <0x280000 0x680000>; /* 6.5MiB */
|
||||
/*
|
||||
* Unused area between "s_env" and "devinfo".
|
||||
* Moved here because otherwise the renumbered
|
||||
* partitions would break the bootloader
|
||||
* supplied bootargs
|
||||
*/
|
||||
partition@180000 {
|
||||
label = "unused_area";
|
||||
reg = <0x280000 0x680000>; /* 6.5MiB */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -81,74 +81,79 @@
|
||||
|
||||
&nand {
|
||||
/* AMD/Spansion S34ML02G2 256MiB, OEM Layout */
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x200000>; /* 2MiB */
|
||||
read-only;
|
||||
};
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x200000>; /* 2MiB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "u_env";
|
||||
reg = <0x200000 0x20000>; /* 128KiB */
|
||||
};
|
||||
partition@200000 {
|
||||
label = "u_env";
|
||||
reg = <0x200000 0x20000>; /* 128KiB */
|
||||
};
|
||||
|
||||
partition@220000 {
|
||||
label = "s_env";
|
||||
reg = <0x220000 0x40000>; /* 256KiB */
|
||||
};
|
||||
partition@220000 {
|
||||
label = "s_env";
|
||||
reg = <0x220000 0x40000>; /* 256KiB */
|
||||
};
|
||||
|
||||
partition@7e0000 {
|
||||
label = "devinfo";
|
||||
reg = <0x7e0000 0x40000>; /* 256KiB */
|
||||
read-only;
|
||||
};
|
||||
partition@7e0000 {
|
||||
label = "devinfo";
|
||||
reg = <0x7e0000 0x40000>; /* 256KiB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@820000 {
|
||||
label = "sysdiag";
|
||||
reg = <0x820000 0x1e0000>; /* 1920KiB */
|
||||
read-only;
|
||||
};
|
||||
partition@820000 {
|
||||
label = "sysdiag";
|
||||
reg = <0x820000 0x1e0000>; /* 1920KiB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* kernel1 overlaps with rootfs1 by design */
|
||||
partition@a00000 {
|
||||
label = "kernel1";
|
||||
reg = <0xa00000 0x5000000>; /* 80MiB */
|
||||
};
|
||||
/* kernel1 overlaps with rootfs1 by design */
|
||||
partition@a00000 {
|
||||
label = "kernel1";
|
||||
reg = <0xa00000 0x5000000>; /* 80MiB */
|
||||
};
|
||||
|
||||
partition@1000000 {
|
||||
label = "rootfs1";
|
||||
reg = <0x1000000 0x4a00000>; /* 74MiB */
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "rootfs1";
|
||||
reg = <0x1000000 0x4a00000>; /* 74MiB */
|
||||
};
|
||||
|
||||
/* kernel2 overlaps with rootfs2 by design */
|
||||
partition@5a00000 {
|
||||
label = "kernel2";
|
||||
reg = <0x5a00000 0x5000000>; /* 80MiB */
|
||||
};
|
||||
/* kernel2 overlaps with rootfs2 by design */
|
||||
partition@5a00000 {
|
||||
label = "kernel2";
|
||||
reg = <0x5a00000 0x5000000>; /* 80MiB */
|
||||
};
|
||||
|
||||
partition@6000000 {
|
||||
label = "rootfs2";
|
||||
reg = <0x6000000 0x4a00000>; /* 74MiB */
|
||||
};
|
||||
partition@6000000 {
|
||||
label = "rootfs2";
|
||||
reg = <0x6000000 0x4a00000>; /* 74MiB */
|
||||
};
|
||||
|
||||
/*
|
||||
* 86MiB, last MiB is for the BBT, not writable
|
||||
*/
|
||||
partition@aa00000 {
|
||||
label = "syscfg";
|
||||
reg = <0xaa00000 0x5600000>;
|
||||
};
|
||||
/*
|
||||
* 86MiB, last MiB is for the BBT, not writable
|
||||
*/
|
||||
partition@aa00000 {
|
||||
label = "syscfg";
|
||||
reg = <0xaa00000 0x5600000>;
|
||||
};
|
||||
|
||||
/*
|
||||
* Unused area between "s_env" and "devinfo".
|
||||
* Moved here because otherwise the renumbered
|
||||
* partitions would break the bootloader
|
||||
* supplied bootargs
|
||||
*/
|
||||
partition@180000 {
|
||||
label = "unused_area";
|
||||
reg = <0x260000 0x5c0000>; /* 5.75MiB */
|
||||
/*
|
||||
* Unused area between "s_env" and "devinfo".
|
||||
* Moved here because otherwise the renumbered
|
||||
* partitions would break the bootloader
|
||||
* supplied bootargs
|
||||
*/
|
||||
partition@180000 {
|
||||
label = "unused_area";
|
||||
reg = <0x260000 0x5c0000>; /* 5.75MiB */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
@ -73,67 +73,72 @@
|
||||
|
||||
&nand {
|
||||
/* 128MiB */
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x200000>; /* 2MiB */
|
||||
read-only;
|
||||
};
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x200000>; /* 2MiB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u_env";
|
||||
reg = <0x200000 0x40000>; /* 256KiB */
|
||||
};
|
||||
partition@100000 {
|
||||
label = "u_env";
|
||||
reg = <0x200000 0x40000>; /* 256KiB */
|
||||
};
|
||||
|
||||
partition@140000 {
|
||||
label = "s_env";
|
||||
reg = <0x240000 0x40000>; /* 256KiB */
|
||||
};
|
||||
partition@140000 {
|
||||
label = "s_env";
|
||||
reg = <0x240000 0x40000>; /* 256KiB */
|
||||
};
|
||||
|
||||
partition@900000 {
|
||||
label = "devinfo";
|
||||
reg = <0x900000 0x100000>; /* 1MiB */
|
||||
read-only;
|
||||
};
|
||||
partition@900000 {
|
||||
label = "devinfo";
|
||||
reg = <0x900000 0x100000>; /* 1MiB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* kernel1 overlaps with rootfs1 by design */
|
||||
partition@a00000 {
|
||||
label = "kernel1";
|
||||
reg = <0xa00000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
/* kernel1 overlaps with rootfs1 by design */
|
||||
partition@a00000 {
|
||||
label = "kernel1";
|
||||
reg = <0xa00000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
|
||||
partition@1000000 {
|
||||
label = "rootfs1";
|
||||
reg = <0x1000000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "rootfs1";
|
||||
reg = <0x1000000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
|
||||
/* kernel2 overlaps with rootfs2 by design */
|
||||
partition@3200000 {
|
||||
label = "kernel2";
|
||||
reg = <0x3200000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
/* kernel2 overlaps with rootfs2 by design */
|
||||
partition@3200000 {
|
||||
label = "kernel2";
|
||||
reg = <0x3200000 0x2800000>; /* 40MiB */
|
||||
};
|
||||
|
||||
partition@3800000 {
|
||||
label = "rootfs2";
|
||||
reg = <0x3800000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
partition@3800000 {
|
||||
label = "rootfs2";
|
||||
reg = <0x3800000 0x2200000>; /* 34MiB */
|
||||
};
|
||||
|
||||
/*
|
||||
* 38MiB, last MiB is for the BBT, not writable
|
||||
*/
|
||||
partition@5a00000 {
|
||||
label = "syscfg";
|
||||
reg = <0x5a00000 0x2600000>;
|
||||
};
|
||||
/*
|
||||
* 38MiB, last MiB is for the BBT, not writable
|
||||
*/
|
||||
partition@5a00000 {
|
||||
label = "syscfg";
|
||||
reg = <0x5a00000 0x2600000>;
|
||||
};
|
||||
|
||||
/*
|
||||
* Unused area between "s_env" and "devinfo".
|
||||
* Moved here because otherwise the renumbered
|
||||
* partitions would break the bootloader
|
||||
* supplied bootargs
|
||||
*/
|
||||
partition@180000 {
|
||||
label = "unused_area";
|
||||
reg = <0x280000 0x680000>; /* 6.5MiB */
|
||||
/*
|
||||
* Unused area between "s_env" and "devinfo".
|
||||
* Moved here because otherwise the renumbered
|
||||
* partitions would break the bootloader
|
||||
* supplied bootargs
|
||||
*/
|
||||
partition@180000 {
|
||||
label = "unused_area";
|
||||
reg = <0x280000 0x680000>; /* 6.5MiB */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -138,13 +138,19 @@
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
&nand_controller {
|
||||
/* 128MiB or 256MiB */
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
nand: nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
|
||||
@ -91,29 +91,6 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
flash@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
|
||||
sdhci@d8000 {
|
||||
broken-cd;
|
||||
wp-inverted;
|
||||
@ -165,3 +142,35 @@
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -551,11 +551,11 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
nand: flash@d0000 {
|
||||
compatible = "marvell,armada370-nand";
|
||||
nand_controller: nand-controller@d0000 {
|
||||
compatible = "marvell,armada370-nand-controller";
|
||||
reg = <0xd0000 0x54>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&coredivclk 0>;
|
||||
status = "disabled";
|
||||
|
||||
@ -49,37 +49,6 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
flash@d0000 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/* CON98 */
|
||||
usb3@f8000 {
|
||||
status = "okay";
|
||||
@ -136,3 +105,38 @@
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -57,41 +57,6 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
flash@d0000 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0x00000000 0x00600000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "uImage";
|
||||
reg = <0x00600000 0x00400000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1000000 {
|
||||
label = "Root";
|
||||
reg = <0x00a00000 0x3f600000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/* CON18 */
|
||||
sdhci@d8000 {
|
||||
clock-frequency = <200000000>;
|
||||
@ -130,3 +95,42 @@
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0x00000000 0x00600000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "uImage";
|
||||
reg = <0x00600000 0x00400000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1000000 {
|
||||
label = "Root";
|
||||
reg = <0x00a00000 0x3f600000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -51,31 +51,6 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
flash@d0000 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
|
||||
usb3@f8000 {
|
||||
status = "okay";
|
||||
};
|
||||
@ -122,3 +97,38 @@
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
partition@800000 {
|
||||
label = "Linux";
|
||||
reg = <0x800000 0x800000>;
|
||||
};
|
||||
partition@1000000 {
|
||||
label = "Filesystem";
|
||||
reg = <0x1000000 0x3f000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -367,11 +367,11 @@
|
||||
interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
|
||||
flash@d0000 {
|
||||
compatible = "marvell,armada370-nand";
|
||||
nand_controller: nand-controller@d0000 {
|
||||
compatible = "marvell,armada370-nand-controller";
|
||||
reg = <0xd0000 0x54>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&coredivclk 0>;
|
||||
status = "disabled";
|
||||
|
||||
@ -306,6 +306,19 @@
|
||||
&pinctrl {
|
||||
compatible = "marvell,98dx3236-pinctrl";
|
||||
|
||||
nand_pins: nand-pins {
|
||||
marvell,pins = "mpp20", "mpp21", "mpp22",
|
||||
"mpp23", "mpp24", "mpp25",
|
||||
"mpp26", "mpp27", "mpp28",
|
||||
"mpp29", "mpp30";
|
||||
marvell,function = "dev";
|
||||
};
|
||||
|
||||
nand_rb: nand-rb {
|
||||
marvell,pins = "mpp19";
|
||||
marvell,function = "nand";
|
||||
};
|
||||
|
||||
spi0_pins: spi0-pins {
|
||||
marvell,pins = "mpp0", "mpp1",
|
||||
"mpp2", "mpp3";
|
||||
|
||||
@ -70,9 +70,9 @@
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
label = "pxa3xx_nand-0";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
@ -69,9 +69,9 @@
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
label = "pxa3xx_nand-0";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
@ -146,9 +146,9 @@
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
label = "pxa3xx_nand-0";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
partitions {
|
||||
|
||||
@ -162,9 +162,9 @@
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
label = "pxa3xx_nand-0";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
};
|
||||
};
|
||||
|
||||
@ -83,9 +83,9 @@
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
label = "pxa3xx_nand-0";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
partitions {
|
||||
|
||||
@ -165,79 +165,6 @@
|
||||
bm@c8000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x100000>; /* 1MB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u_env";
|
||||
reg = <0x100000 0x40000>; /* 256KB */
|
||||
};
|
||||
|
||||
partition@140000 {
|
||||
label = "s_env";
|
||||
reg = <0x140000 0x40000>; /* 256KB */
|
||||
};
|
||||
|
||||
partition@900000 {
|
||||
label = "devinfo";
|
||||
reg = <0x900000 0x100000>; /* 1MB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* kernel1 overlaps with rootfs1 by design */
|
||||
partition@a00000 {
|
||||
label = "kernel1";
|
||||
reg = <0xa00000 0x2800000>; /* 40MB */
|
||||
};
|
||||
|
||||
partition@d00000 {
|
||||
label = "rootfs1";
|
||||
reg = <0xd00000 0x2500000>; /* 37MB */
|
||||
};
|
||||
|
||||
/* kernel2 overlaps with rootfs2 by design */
|
||||
partition@3200000 {
|
||||
label = "kernel2";
|
||||
reg = <0x3200000 0x2800000>; /* 40MB */
|
||||
};
|
||||
|
||||
partition@3500000 {
|
||||
label = "rootfs2";
|
||||
reg = <0x3500000 0x2500000>; /* 37MB */
|
||||
};
|
||||
|
||||
/*
|
||||
* 38MB, last MB is for the BBT, not writable
|
||||
*/
|
||||
partition@5a00000 {
|
||||
label = "syscfg";
|
||||
reg = <0x5a00000 0x2600000>;
|
||||
};
|
||||
|
||||
/*
|
||||
* Unused area between "s_env" and "devinfo".
|
||||
* Moved here because otherwise the renumbered
|
||||
* partitions would break the bootloader
|
||||
* supplied bootargs
|
||||
*/
|
||||
partition@180000 {
|
||||
label = "unused_area";
|
||||
reg = <0x180000 0x780000>; /* 7.5MB */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
bm-bppi {
|
||||
@ -434,3 +361,86 @@
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x100000>; /* 1MB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u_env";
|
||||
reg = <0x100000 0x40000>; /* 256KB */
|
||||
};
|
||||
|
||||
partition@140000 {
|
||||
label = "s_env";
|
||||
reg = <0x140000 0x40000>; /* 256KB */
|
||||
};
|
||||
|
||||
partition@900000 {
|
||||
label = "devinfo";
|
||||
reg = <0x900000 0x100000>; /* 1MB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* kernel1 overlaps with rootfs1 by design */
|
||||
partition@a00000 {
|
||||
label = "kernel1";
|
||||
reg = <0xa00000 0x2800000>; /* 40MB */
|
||||
};
|
||||
|
||||
partition@d00000 {
|
||||
label = "rootfs1";
|
||||
reg = <0xd00000 0x2500000>; /* 37MB */
|
||||
};
|
||||
|
||||
/* kernel2 overlaps with rootfs2 by design */
|
||||
partition@3200000 {
|
||||
label = "kernel2";
|
||||
reg = <0x3200000 0x2800000>; /* 40MB */
|
||||
};
|
||||
|
||||
partition@3500000 {
|
||||
label = "rootfs2";
|
||||
reg = <0x3500000 0x2500000>; /* 37MB */
|
||||
};
|
||||
|
||||
/*
|
||||
* 38MB, last MB is for the BBT, not writable
|
||||
*/
|
||||
partition@5a00000 {
|
||||
label = "syscfg";
|
||||
reg = <0x5a00000 0x2600000>;
|
||||
};
|
||||
|
||||
/*
|
||||
* Unused area between "s_env" and "devinfo".
|
||||
* Moved here because otherwise the renumbered
|
||||
* partitions would break the bootloader
|
||||
* supplied bootargs
|
||||
*/
|
||||
partition@180000 {
|
||||
label = "unused_area";
|
||||
reg = <0x180000 0x780000>; /* 7.5MB */
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -117,46 +117,6 @@
|
||||
nr-ports = <2>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
/* Use Hardware BCH ECC */
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x180000>; /* 1.5MB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x180000 0x20000>; /* 128KB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "uImage";
|
||||
reg = <0x0200000 0x600000>; /* 6MB */
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "minirootfs";
|
||||
reg = <0x0800000 0x400000>; /* 4MB */
|
||||
};
|
||||
|
||||
/* Last MB is for the BBT, i.e. not writable */
|
||||
partition@c00000 {
|
||||
label = "ubifs";
|
||||
reg = <0x0c00000 0x7400000>; /* 116MB */
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -345,3 +305,53 @@
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
|
||||
/* Use Hardware BCH ECC */
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0000000 0x180000>; /* 1.5MB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x180000 0x20000>; /* 128KB */
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "uImage";
|
||||
reg = <0x0200000 0x600000>; /* 6MB */
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "minirootfs";
|
||||
reg = <0x0800000 0x400000>; /* 4MB */
|
||||
};
|
||||
|
||||
/* Last MB is for the BBT, i.e. not writable */
|
||||
partition@c00000 {
|
||||
label = "ubifs";
|
||||
reg = <0x0c00000 0x7400000>; /* 116MB */
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -79,3 +79,21 @@
|
||||
reg = <0x4d>;
|
||||
};
|
||||
};
|
||||
|
||||
&ehci0 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usb2ah_default>;
|
||||
};
|
||||
|
||||
&ehci1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usb2bh_default>;
|
||||
};
|
||||
|
||||
&uhci {
|
||||
status = "okay";
|
||||
|
||||
/* No pinctrl, this follows the above EHCI settings */
|
||||
};
|
||||
|
||||
129
arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dts
Normal file
129
arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dts
Normal file
@ -0,0 +1,129 @@
|
||||
// SPDX-License-Identifier: GPL-2.0
|
||||
// Copyright (c) 2017 Intel Corporation
|
||||
/dts-v1/;
|
||||
|
||||
#include "aspeed-g5.dtsi"
|
||||
|
||||
/ {
|
||||
model = "S2600WF BMC";
|
||||
compatible = "intel,s2600wf-bmc", "aspeed,ast2500";
|
||||
|
||||
chosen {
|
||||
stdout-path = &uart5;
|
||||
bootargs = "earlyprintk";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0x80000000 0x20000000>;
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
|
||||
vga_memory: framebuffer@7f000000 {
|
||||
no-map;
|
||||
reg = <0x7f000000 0x01000000>;
|
||||
};
|
||||
};
|
||||
|
||||
iio-hwmon {
|
||||
compatible = "iio-hwmon";
|
||||
io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
|
||||
<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
|
||||
<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
|
||||
<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&fmc {
|
||||
status = "okay";
|
||||
flash@0 {
|
||||
status = "okay";
|
||||
m25p,fast-read;
|
||||
label = "bmc";
|
||||
#include "openbmc-flash-layout.dtsi"
|
||||
};
|
||||
};
|
||||
|
||||
&spi1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_spi1_default>;
|
||||
|
||||
flash@0 {
|
||||
status = "okay";
|
||||
m25p,fast-read;
|
||||
label = "pnor";
|
||||
};
|
||||
};
|
||||
|
||||
&uart5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mac0 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_rmii1_default>;
|
||||
use-ncsi;
|
||||
};
|
||||
|
||||
&mac1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c4 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c6 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c7 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c13 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gfx {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
aspeed,external-nodes = <&gfx &lhc>;
|
||||
};
|
||||
|
||||
&pwm_tacho {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
|
||||
&pinctrl_pwm2_default &pinctrl_pwm3_default
|
||||
&pinctrl_pwm4_default &pinctrl_pwm5_default
|
||||
&pinctrl_pwm6_default &pinctrl_pwm7_default>;
|
||||
};
|
||||
325
arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dts
Normal file
325
arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dts
Normal file
@ -0,0 +1,325 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
// Copyright (c) 2018 Inventec Corporation
|
||||
/dts-v1/;
|
||||
|
||||
#include "aspeed-g5.dtsi"
|
||||
#include <dt-bindings/gpio/aspeed-gpio.h>
|
||||
|
||||
/ {
|
||||
model = "Lanyang BMC";
|
||||
compatible = "inventec,lanyang-bmc", "aspeed,ast2500";
|
||||
|
||||
chosen {
|
||||
stdout-path = &uart5;
|
||||
bootargs = "console=ttyS4,115200 earlyprintk";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0x80000000 0x40000000>;
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
|
||||
flash_memory: region@98000000 {
|
||||
no-map;
|
||||
reg = <0x98000000 0x04000000>; /* 64M */
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
sys_boot_status {
|
||||
label = "System_boot_status";
|
||||
gpios = <&gpio ASPEED_GPIO(B, 6) GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
attention {
|
||||
label = "Attention_locator";
|
||||
gpios = <&gpio ASPEED_GPIO(B, 7) GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
plt_fault {
|
||||
label = "Platform_fault";
|
||||
gpios = <&gpio ASPEED_GPIO(B, 1) GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
hdd_fault {
|
||||
label = "Onboard_drive_fault";
|
||||
gpios = <&gpio ASPEED_GPIO(B, 3) GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
bmc_err {
|
||||
lable = "BMC_fault";
|
||||
gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
sys_err {
|
||||
lable = "Sys_fault";
|
||||
gpios = <&gpio ASPEED_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
fsi: gpio-fsi {
|
||||
compatible = "fsi-master-gpio", "fsi-master";
|
||||
#address-cells = <2>;
|
||||
#size-cells = <0>;
|
||||
|
||||
clock-gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_HIGH>;
|
||||
data-gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_HIGH>;
|
||||
trans-gpios = <&gpio ASPEED_GPIO(D, 5) GPIO_ACTIVE_HIGH>;
|
||||
enable-gpios = <&gpio ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
|
||||
mux-gpios = <&gpio ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
iio-hwmon {
|
||||
compatible = "iio-hwmon";
|
||||
io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
|
||||
<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
|
||||
<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
|
||||
<&adc 13>, <&adc 14>, <&adc 15>;
|
||||
};
|
||||
|
||||
iio-hwmon-battery {
|
||||
compatible = "iio-hwmon";
|
||||
io-channels = <&adc 12>;
|
||||
};
|
||||
};
|
||||
|
||||
&pwm_tacho {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
|
||||
&pinctrl_pwm2_default &pinctrl_pwm3_default>;
|
||||
|
||||
fan@0 {
|
||||
reg = <0x00>;
|
||||
aspeed,fan-tach-ch = /bits/ 8 <0x00>;
|
||||
};
|
||||
|
||||
fan@1 {
|
||||
reg = <0x01>;
|
||||
aspeed,fan-tach-ch = /bits/ 8 <0x01>;
|
||||
};
|
||||
|
||||
fan@2 {
|
||||
reg = <0x02>;
|
||||
aspeed,fan-tach-ch = /bits/ 8 <0x02>;
|
||||
};
|
||||
|
||||
fan@3 {
|
||||
reg = <0x03>;
|
||||
aspeed,fan-tach-ch = /bits/ 8 <0x03>;
|
||||
};
|
||||
};
|
||||
|
||||
&fmc {
|
||||
status = "okay";
|
||||
flash@0 {
|
||||
status = "okay";
|
||||
m25p,fast-read;
|
||||
label = "bmc";
|
||||
#include "openbmc-flash-layout.dtsi"
|
||||
};
|
||||
};
|
||||
|
||||
&spi1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_spi1_default>;
|
||||
|
||||
flash@0 {
|
||||
status = "okay";
|
||||
label = "pnor";
|
||||
m25p,fast-read;
|
||||
};
|
||||
};
|
||||
|
||||
&spi2 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_spi2ck_default
|
||||
&pinctrl_spi2cs0_default
|
||||
&pinctrl_spi2cs1_default
|
||||
&pinctrl_spi2miso_default
|
||||
&pinctrl_spi2mosi_default>;
|
||||
|
||||
flash@0 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_txd1_default
|
||||
&pinctrl_rxd1_default>;
|
||||
};
|
||||
|
||||
&lpc_ctrl {
|
||||
status = "okay";
|
||||
memory-region = <&flash_memory>;
|
||||
flash = <&spi1>;
|
||||
};
|
||||
|
||||
&lpc_snoop {
|
||||
status = "okay";
|
||||
snoop-ports = <0x80>;
|
||||
};
|
||||
|
||||
&uart5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mac0 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_rmii1_default>;
|
||||
use-ncsi;
|
||||
};
|
||||
|
||||
&mac1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
|
||||
eeprom@55 {
|
||||
compatible = "atmel,24c64";
|
||||
reg = <0x55>;
|
||||
pagesize = <32>;
|
||||
};
|
||||
|
||||
rtc@68 {
|
||||
compatible = "nxp,pcf8523";
|
||||
reg = <0x68>;
|
||||
};
|
||||
|
||||
tmp75@48 {
|
||||
compatible = "ti,tmp75";
|
||||
reg = <0x48>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c4 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c6 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c7 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c8 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c9 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c10 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c11 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&vuart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gfx {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
aspeed,external-nodes = <&gfx &lhc>;
|
||||
};
|
||||
|
||||
&gpio {
|
||||
pin_gpio_b0 {
|
||||
gpio-hog;
|
||||
gpios = <ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "BMC_HDD1_PWR_EN";
|
||||
};
|
||||
|
||||
pin_gpio_b5 {
|
||||
gpio-hog;
|
||||
gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
|
||||
input;
|
||||
line-name = "BMC_USB1_OCI2";
|
||||
};
|
||||
|
||||
pin_gpio_h5 {
|
||||
gpio-hog;
|
||||
gpios = <ASPEED_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "BMC_CP0_PERST_ENABLE_R";
|
||||
};
|
||||
|
||||
pin_gpio_z2 {
|
||||
gpio-hog;
|
||||
gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "RST_PCA9546_U177_N";
|
||||
};
|
||||
|
||||
pin_gpio_aa6 {
|
||||
gpio-hog;
|
||||
gpios = <ASPEED_GPIO(AA, 6) GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "BMC_CP0_RESET_N";
|
||||
};
|
||||
|
||||
pin_gpio_aa7 {
|
||||
gpio-hog;
|
||||
gpios = <ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "BMC_TPM_RESET_N";
|
||||
};
|
||||
|
||||
pin_gpio_ab0 {
|
||||
gpio-hog;
|
||||
gpios = <ASPEED_GPIO(AB, 0) GPIO_ACTIVE_LOW>;
|
||||
output-high;
|
||||
line-name = "BMC_USB_PWRON_N";
|
||||
};
|
||||
};
|
||||
|
||||
&ibt {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&adc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -68,6 +68,12 @@
|
||||
gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
|
||||
linux,code = <ASPEED_GPIO(J, 2)>;
|
||||
};
|
||||
|
||||
id-button {
|
||||
label = "id-button";
|
||||
gpios = <&gpio ASPEED_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
|
||||
linux,code = <ASPEED_GPIO(Q, 7)>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
@ -28,6 +28,34 @@
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
air-water {
|
||||
label = "air-water";
|
||||
gpios = <&gpio ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>;
|
||||
linux,code = <ASPEED_GPIO(B, 5)>;
|
||||
};
|
||||
|
||||
checkstop {
|
||||
label = "checkstop";
|
||||
gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
|
||||
linux,code = <ASPEED_GPIO(J, 2)>;
|
||||
};
|
||||
|
||||
ps0-presence {
|
||||
label = "ps0-presence";
|
||||
gpios = <&gpio ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
|
||||
linux,code = <ASPEED_GPIO(P, 7)>;
|
||||
};
|
||||
|
||||
ps1-presence {
|
||||
label = "ps1-presence";
|
||||
gpios = <&gpio ASPEED_GPIO(N, 0) GPIO_ACTIVE_LOW>;
|
||||
linux,code = <ASPEED_GPIO(N, 0)>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys-polled {
|
||||
compatible = "gpio-keys-polled";
|
||||
#address-cells = <1>;
|
||||
@ -547,6 +575,10 @@
|
||||
pinctrl-0 = <&pinctrl_wdtrst1_default>;
|
||||
};
|
||||
|
||||
&wdt2 {
|
||||
aspeed,alt-boot;
|
||||
};
|
||||
|
||||
&ibt {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -55,6 +55,12 @@
|
||||
gpios = <&gpio ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>;
|
||||
linux,code = <ASPEED_GPIO(F, 7)>;
|
||||
};
|
||||
|
||||
pcie-e2b-present{
|
||||
label = "pcie-e2b-present";
|
||||
gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
|
||||
linux,code = <ASPEED_GPIO(E, 7)>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
|
||||
159
arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts
Normal file
159
arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts
Normal file
@ -0,0 +1,159 @@
|
||||
// SPDX-License-Identifier: GPL-2.0
|
||||
// Copyright (c) 2017 Facebook Inc.
|
||||
/dts-v1/;
|
||||
|
||||
#include "aspeed-g5.dtsi"
|
||||
#include <dt-bindings/gpio/aspeed-gpio.h>
|
||||
|
||||
/ {
|
||||
model = "Portwell Neptune BMC";
|
||||
compatible = "portwell,neptune-bmc", "aspeed,ast2500";
|
||||
aliases {
|
||||
serial0 = &uart1;
|
||||
serial4 = &uart5;
|
||||
};
|
||||
chosen {
|
||||
stdout-path = &uart5;
|
||||
bootargs = "console=ttyS4,115200 earlyprintk";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0x80000000 0x20000000>;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
postcode0 {
|
||||
label="BMC_UP";
|
||||
gpios = <&gpio ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
};
|
||||
postcode1 {
|
||||
label="BMC_HB";
|
||||
gpios = <&gpio ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
};
|
||||
postcode2 {
|
||||
label="FAULT";
|
||||
gpios = <&gpio ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
// postcode3-7 are GPIOH3-H7
|
||||
};
|
||||
};
|
||||
|
||||
&fmc {
|
||||
status = "okay";
|
||||
flash@0 {
|
||||
status = "okay";
|
||||
m25p,fast-read;
|
||||
#include "openbmc-flash-layout.dtsi"
|
||||
};
|
||||
};
|
||||
|
||||
&spi1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_spi1_default>;
|
||||
flash@0 {
|
||||
status = "okay";
|
||||
m25p,fast-read;
|
||||
label = "pnor";
|
||||
};
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
// Host Console
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_txd1_default
|
||||
&pinctrl_rxd1_default>;
|
||||
};
|
||||
|
||||
&uart5 {
|
||||
// BMC Console
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mac0 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_rmii1_default
|
||||
&pinctrl_mdio1_default>;
|
||||
};
|
||||
|
||||
&mac1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_rmii2_default>;
|
||||
use-ncsi;
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
status = "okay";
|
||||
// To PCIe slot SMBUS
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
status = "okay";
|
||||
// To LAN I210
|
||||
};
|
||||
|
||||
&i2c3 {
|
||||
status = "okay";
|
||||
// SMBus to COMe AB
|
||||
};
|
||||
|
||||
&i2c4 {
|
||||
status = "okay";
|
||||
// I2C to COMe AB
|
||||
};
|
||||
|
||||
&i2c5 {
|
||||
status = "okay";
|
||||
// USB Debug card
|
||||
pca9555@27 {
|
||||
compatible = "nxp,pca9555";
|
||||
reg = <0x27>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c6 {
|
||||
status = "okay";
|
||||
tpm@20 {
|
||||
compatible = "infineon,slb9645tt";
|
||||
reg = <0x20>;
|
||||
};
|
||||
tmp421@4e {
|
||||
compatible = "ti,tmp421";
|
||||
reg = <0x4e>;
|
||||
};
|
||||
tmp421@4f {
|
||||
compatible = "ti,tmp421";
|
||||
reg = <0x4f>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c8 {
|
||||
status = "okay";
|
||||
eeprom@51 {
|
||||
compatible = "atmel,24c128";
|
||||
reg = <0x51>;
|
||||
pagesize = <32>;
|
||||
};
|
||||
};
|
||||
|
||||
&pwm_tacho {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>;
|
||||
fan@0 {
|
||||
reg = <0x00>;
|
||||
aspeed,fan-tach-ch = /bits/ 8 <0x00>;
|
||||
};
|
||||
|
||||
fan@1 {
|
||||
reg = <0x00>;
|
||||
aspeed,fan-tach-ch = /bits/ 8 <0x01>;
|
||||
};
|
||||
};
|
||||
@ -108,6 +108,23 @@
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
ehci0: usb@1e6a1000 {
|
||||
compatible = "aspeed,ast2400-ehci", "generic-ehci";
|
||||
reg = <0x1e6a1000 0x100>;
|
||||
interrupts = <5>;
|
||||
clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uhci: usb@1e6b0000 {
|
||||
compatible = "aspeed,ast2400-uhci", "generic-uhci";
|
||||
reg = <0x1e6b0000 0x100>;
|
||||
interrupts = <14>;
|
||||
#ports = <3>;
|
||||
clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
apb {
|
||||
compatible = "simple-bus";
|
||||
#address-cells = <1>;
|
||||
@ -125,6 +142,14 @@
|
||||
pinctrl: pinctrl {
|
||||
compatible = "aspeed,g4-pinctrl";
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
rng: hwrng@1e6e2078 {
|
||||
compatible = "timeriomem_rng";
|
||||
reg = <0x1e6e2078 0x4>;
|
||||
period = <1>;
|
||||
quality = <100>;
|
||||
};
|
||||
|
||||
adc: adc@1e6e9000 {
|
||||
@ -1250,6 +1275,16 @@
|
||||
groups = "USBCKI";
|
||||
};
|
||||
|
||||
pinctrl_usb2h_default: usb2h_default {
|
||||
function = "USB2H1";
|
||||
groups = "USB2H1";
|
||||
};
|
||||
|
||||
pinctrl_usb2d_default: usb2d_default {
|
||||
function = "USB2D1";
|
||||
groups = "USB2D1";
|
||||
};
|
||||
|
||||
pinctrl_vgabios_rom_default: vgabios_rom_default {
|
||||
function = "VGABIOS_ROM";
|
||||
groups = "VGABIOS_ROM";
|
||||
|
||||
@ -143,6 +143,31 @@
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
ehci0: usb@1e6a1000 {
|
||||
compatible = "aspeed,ast2500-ehci", "generic-ehci";
|
||||
reg = <0x1e6a1000 0x100>;
|
||||
interrupts = <5>;
|
||||
clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
ehci1: usb@1e6a3000 {
|
||||
compatible = "aspeed,ast2500-ehci", "generic-ehci";
|
||||
reg = <0x1e6a3000 0x100>;
|
||||
interrupts = <13>;
|
||||
clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uhci: usb@1e6b0000 {
|
||||
compatible = "aspeed,ast2500-uhci", "generic-uhci";
|
||||
reg = <0x1e6b0000 0x100>;
|
||||
interrupts = <14>;
|
||||
#ports = <2>;
|
||||
clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
apb {
|
||||
compatible = "simple-bus";
|
||||
#address-cells = <1>;
|
||||
@ -164,6 +189,13 @@
|
||||
};
|
||||
};
|
||||
|
||||
rng: hwrng@1e6e2078 {
|
||||
compatible = "timeriomem_rng";
|
||||
reg = <0x1e6e2078 0x4>;
|
||||
period = <1>;
|
||||
quality = <100>;
|
||||
};
|
||||
|
||||
gfx: display@1e6e6000 {
|
||||
compatible = "aspeed,ast2500-gfx", "syscon";
|
||||
reg = <0x1e6e6000 0x1000>;
|
||||
@ -1380,6 +1412,21 @@
|
||||
groups = "USBCKI";
|
||||
};
|
||||
|
||||
pinctrl_usb2ah_default: usb2ah_default {
|
||||
function = "USB2AH";
|
||||
groups = "USB2AH";
|
||||
};
|
||||
|
||||
pinctrl_usb11bhid_default: usb11bhid_default {
|
||||
function = "USB11BHID";
|
||||
groups = "USB11BHID";
|
||||
};
|
||||
|
||||
pinctrl_usb2bh_default: usb2bh_default {
|
||||
function = "USB2BH";
|
||||
groups = "USB2BH";
|
||||
};
|
||||
|
||||
pinctrl_vgabiosrom_default: vgabiosrom_default {
|
||||
function = "VGABIOSROM";
|
||||
groups = "VGABIOSROM";
|
||||
|
||||
@ -232,7 +232,7 @@
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>;
|
||||
interrupt-parent = <&pioA>;
|
||||
interrupts = <PIN_PB13 GPIO_ACTIVE_LOW>;
|
||||
interrupts = <PIN_PB13 IRQ_TYPE_EDGE_RISING>;
|
||||
|
||||
active-semi,chglev-gpios = <&pioA PIN_PA12 GPIO_ACTIVE_HIGH>;
|
||||
active-semi,lbo-gpios = <&pioA PIN_PC8 GPIO_ACTIVE_LOW>;
|
||||
|
||||
@ -129,8 +129,8 @@
|
||||
wakeup-source;
|
||||
};
|
||||
|
||||
atmel_mxt_ts@4c {
|
||||
compatible = "atmel,atmel_mxt_ts";
|
||||
touchscreen@4c {
|
||||
compatible = "atmel,maxtouch";
|
||||
reg = <0x4c>;
|
||||
interrupt-parent = <&pioE>;
|
||||
interrupts = <24 0x0>;
|
||||
|
||||
@ -101,6 +101,12 @@
|
||||
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart0_gpio14>;
|
||||
|
||||
@ -96,6 +96,12 @@
|
||||
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart0_gpio14>;
|
||||
|
||||
@ -103,6 +103,12 @@
|
||||
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart0_gpio14>;
|
||||
|
||||
@ -96,6 +96,12 @@
|
||||
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart0_gpio14>;
|
||||
|
||||
@ -91,6 +91,12 @@
|
||||
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart0_gpio14>;
|
||||
|
||||
@ -83,12 +83,6 @@
|
||||
bus-width = <4>;
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb {
|
||||
power-domains = <&power RPI_POWER_DOMAIN_USB>;
|
||||
};
|
||||
|
||||
@ -41,6 +41,12 @@
|
||||
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart0_gpio14>;
|
||||
|
||||
108
arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
Normal file
108
arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
Normal file
@ -0,0 +1,108 @@
|
||||
// SPDX-License-Identifier: GPL-2.0
|
||||
/dts-v1/;
|
||||
#include "bcm2837.dtsi"
|
||||
#include "bcm2835-rpi.dtsi"
|
||||
#include "bcm283x-rpi-lan7515.dtsi"
|
||||
#include "bcm283x-rpi-usb-host.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
|
||||
model = "Raspberry Pi 3 Model B+";
|
||||
|
||||
chosen {
|
||||
/* 8250 auxiliary UART instead of pl011 */
|
||||
stdout-path = "serial1:115200n8";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000>;
|
||||
};
|
||||
|
||||
leds {
|
||||
act {
|
||||
gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
pwr {
|
||||
label = "PWR";
|
||||
gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi-pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&expgpio 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&firmware {
|
||||
expgpio: gpio {
|
||||
compatible = "raspberrypi,firmware-gpio";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
gpio-line-names = "BT_ON",
|
||||
"WL_ON",
|
||||
"STATUS_LED",
|
||||
"LAN_RUN",
|
||||
"",
|
||||
"CAM_GPIO0",
|
||||
"CAM_GPIO1",
|
||||
"";
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&hdmi {
|
||||
hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* SDHCI is used to control the SDIO for wireless */
|
||||
&sdhci {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&emmc_gpio34>;
|
||||
status = "okay";
|
||||
bus-width = <4>;
|
||||
non-removable;
|
||||
mmc-pwrseq = <&wifi_pwrseq>;
|
||||
|
||||
brcmf: wifi@1 {
|
||||
reg = <1>;
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
};
|
||||
};
|
||||
|
||||
/* SDHOST is used to drive the SD card */
|
||||
&sdhost {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdhost_gpio48>;
|
||||
status = "okay";
|
||||
bus-width = <4>;
|
||||
};
|
||||
|
||||
/* uart0 communicates with the BT module */
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
|
||||
status = "okay";
|
||||
|
||||
bluetooth {
|
||||
compatible = "brcm,bcm43438-bt";
|
||||
max-speed = <2000000>;
|
||||
shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
/* uart1 is mapped to the pin header */
|
||||
&uart1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart1_gpio14>;
|
||||
status = "okay";
|
||||
};
|
||||
@ -20,9 +20,14 @@
|
||||
|
||||
leds {
|
||||
act {
|
||||
gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi-pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&expgpio 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&firmware {
|
||||
@ -42,6 +47,16 @@
|
||||
};
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hdmi {
|
||||
hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
/* uart0 communicates with the BT module */
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
@ -51,6 +66,7 @@
|
||||
bluetooth {
|
||||
compatible = "brcm,bcm43438-bt";
|
||||
max-speed = <2000000>;
|
||||
shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -63,11 +79,19 @@
|
||||
|
||||
/* SDHCI is used to control the SDIO for wireless */
|
||||
&sdhci {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&emmc_gpio34>;
|
||||
status = "okay";
|
||||
bus-width = <4>;
|
||||
non-removable;
|
||||
mmc-pwrseq = <&wifi_pwrseq>;
|
||||
|
||||
brcmf: wifi@1 {
|
||||
reg = <1>;
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
};
|
||||
};
|
||||
|
||||
/* SDHOST is used to drive the SD card */
|
||||
|
||||
27
arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi
Normal file
27
arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi
Normal file
@ -0,0 +1,27 @@
|
||||
// SPDX-License-Identifier: GPL-2.0
|
||||
/ {
|
||||
aliases {
|
||||
ethernet0 = ðernet;
|
||||
};
|
||||
};
|
||||
|
||||
&usb {
|
||||
usb-port@1 {
|
||||
compatible = "usb424,2514";
|
||||
reg = <1>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb-port@1 {
|
||||
compatible = "usb424,2514";
|
||||
reg = <1>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ethernet: ethernet@1 {
|
||||
compatible = "usb424,7800";
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -136,6 +136,7 @@
|
||||
rng@7e104000 {
|
||||
compatible = "brcm,bcm2835-rng";
|
||||
reg = <0x7e104000 0x10>;
|
||||
interrupts = <2 29>;
|
||||
};
|
||||
|
||||
mailbox: mailbox@7e00b880 {
|
||||
|
||||
@ -1,20 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Broadcom BCM470X / BCM5301X ARM platform code.
|
||||
* DTS for Asus RT-AC56U
|
||||
*
|
||||
* Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
|
||||
* REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
|
||||
* AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
|
||||
* INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
|
||||
* LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
|
||||
* OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
|
||||
* PERFORMANCE OF THIS SOFTWARE.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,20 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Broadcom BCM470X / BCM5301X ARM platform code.
|
||||
* DTS for Asus RT-AC68U
|
||||
*
|
||||
* Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
|
||||
* REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
|
||||
* AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
|
||||
* INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
|
||||
* LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
|
||||
* OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
|
||||
* PERFORMANCE OF THIS SOFTWARE.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,10 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Broadcom BCM470X / BCM5301X ARM platform code.
|
||||
* DTS for Buffalo WZR-1750DHP
|
||||
*
|
||||
* Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
|
||||
*
|
||||
* Licensed under the GNU/GPL. See COPYING for details.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,7 +1,6 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl>
|
||||
*
|
||||
* Licensed under the ISC license.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,7 +1,6 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Copyright 2016 Luxul Inc.
|
||||
*
|
||||
* Licensed under the ISC license.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,10 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Broadcom BCM470X / BCM5301X ARM platform code.
|
||||
* DTS for Luxul XWC-1000
|
||||
*
|
||||
* Copyright 2014 Luxul Inc.
|
||||
*
|
||||
* Licensed under the GNU/GPL. See COPYING for details.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
@ -26,9 +25,15 @@
|
||||
|
||||
nand: nand@18028000 {
|
||||
nandcs@0 {
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0x00000000 0x08000000>;
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0x00000000 0x08000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -1,20 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Broadcom BCM470X / BCM5301X ARM platform code.
|
||||
* DTS for Netgear R6300 V2
|
||||
*
|
||||
* Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
|
||||
* REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
|
||||
* AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
|
||||
* INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
|
||||
* LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
|
||||
* OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
|
||||
* PERFORMANCE OF THIS SOFTWARE.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,10 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Broadcom BCM470X / BCM5301X arm platform code.
|
||||
* DTS for SmartRG SR400ac
|
||||
*
|
||||
* Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
|
||||
*
|
||||
* Licensed under the GNU/GPL. See COPYING for details.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,20 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Broadcom BCM470X / BCM5301X ARM platform code.
|
||||
* DTS for Asus RT-N18U
|
||||
*
|
||||
* Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
|
||||
* REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
|
||||
* AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
|
||||
* INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
|
||||
* LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
|
||||
* OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
|
||||
* PERFORMANCE OF THIS SOFTWARE.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,20 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Broadcom BCM470X / BCM5301X ARM platform code.
|
||||
* DTS for Buffalo WZR-600DHP2
|
||||
*
|
||||
* Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
|
||||
* REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
|
||||
* AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
|
||||
* INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
|
||||
* LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
|
||||
* OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
|
||||
* PERFORMANCE OF THIS SOFTWARE.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
@ -1,20 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Broadcom BCM470X / BCM5301X ARM platform code.
|
||||
* DTS for Buffalo WZR-900DHP
|
||||
*
|
||||
* Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
|
||||
* REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
|
||||
* AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
|
||||
* INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
|
||||
* LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
|
||||
* OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
|
||||
* PERFORMANCE OF THIS SOFTWARE.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
Some files were not shown because too many files have changed in this diff Show More
Loading…
Reference in New Issue
Block a user