[libata] Delete pata_it8172 driver

This MIPS platform is going away.

Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This commit is contained in:
Jeff Garzik 2006-09-20 17:48:53 -04:00
parent 9359085988
commit 36b35a5be0
3 changed files with 0 additions and 298 deletions

View File

@ -288,15 +288,6 @@ config PATA_ISAPNP
If unsure, say N.
config PATA_IT8172
tristate "IT8172 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the ITE 8172 PATA controller
via the new ATA layer.
If unsure, say N.
config PATA_IT821X
tristate "IT821x PATA support (Experimental)"
depends on PCI && EXPERIMENTAL

View File

@ -32,7 +32,6 @@ obj-$(CONFIG_PATA_HPT37X) += pata_hpt37x.o
obj-$(CONFIG_PATA_HPT3X2N) += pata_hpt3x2n.o
obj-$(CONFIG_PATA_HPT3X3) += pata_hpt3x3.o
obj-$(CONFIG_PATA_ISAPNP) += pata_isapnp.o
obj-$(CONFIG_PATA_IT8172) += pata_it8172.o
obj-$(CONFIG_PATA_IT821X) += pata_it821x.o
obj-$(CONFIG_PATA_JMICRON) += pata_jmicron.o
obj-$(CONFIG_PATA_NETCELL) += pata_netcell.o

View File

@ -1,288 +0,0 @@
/*
* pata_it8172.c - IT8172 PATA for new ATA layer
* (C) 2005 Red Hat Inc
* Alan Cox <alan@redhat.com>
*
* Based heavily on
*
* BRIEF MODULE DESCRIPTION
* IT8172 IDE controller support
*
* Copyright 2000 MontaVista Software Inc.
* Author: MontaVista Software, Inc.
* stevel@mvista.com or source@mvista.com
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*
* TODO
* Check for errata
* See if we really need to force native mode
* PIO timings (also lacking in original)
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_it8172"
#define DRV_VERSION "0.3.1"
static int it8172_pre_reset(struct ata_port *ap)
{
static const struct pci_bits it8172_enable_bits[] = {
{ 0x00, 0, 0x00, 0x00 },
{ 0x40, 1, 0x00, 0x01 }
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
if (ap->port_no && !pci_test_config_bits(pdev, &it8172_enable_bits[ap->port_no])) {
ata_port_disable(ap);
printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
return 0;
}
ap->cbl = ATA_CBL_PATA40;
return ata_std_prereset(ap);
}
static void it8172_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, it8172_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
/**
* it8172_set_pio_timing - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called by both the pio and dma setup functions to set the controller
* timings for PIO transfers. We must load both the mode number and
* timing values into the controller.
*/
static void it8172_set_pio_timing(struct ata_port *ap, struct ata_device *adev, int pio)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u16 reg40;
pci_read_config_word(pdev, 0x40, &reg40);
/*
* FIX! The DIOR/DIOW pulse width and recovery times in port 0x44
* are being left at the default values of 8 PCI clocks (242 nsec
* for a 33 MHz clock). These can be safely shortened at higher
* PIO modes. The DIOR/DIOW pulse width and recovery times only
* apply to PIO modes, not to the DMA modes.
*/
/*
* Enable port 0x44. The IT8172G spec is confused; it calls
* this register the "Slave IDE Timing Register", but in fact,
* it controls timing for both master and slave drives.
*/
reg40 |= 0x4000;
if (adev->devno) {
reg40 &= 0xC006;
if (pio > 1)
/* Enable prefetch and IORDY sample-point */
reg40 |= 0x0060;
} else {
reg40 &= 0xC060;
if (pio > 1)
/* Enable prefetch and IORDY sample-point */
reg40 |= 0x0006;
}
/* Write back the enables */
pci_write_config_word(pdev, 0x40, reg40);
}
/**
* it8172_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the PIO mode setup. We use a shared helper for this
* as the DMA setup must also adjust the PIO timing information.
*/
static void it8172_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
it8172_set_pio_timing(ap, adev, adev->pio_mode - XFER_PIO_0);
}
/**
* it8172_set_dmamode - set initial DMA mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the DMA mode setup. We must tune an appropriate PIO
* mode to match.
*/
static void it8172_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int dn = (2 * ap->port_no) + adev->devno;
u8 reg48, reg4a;
int pio;
static const int pio_map[] = { 1, 3, 4};
/*
* Setting the DMA cycle time to 2 or 3 PCI clocks (60 and 91 nsec
* at 33 MHz PCI clock) seems to cause BadCRC errors during DMA
* transfers on some drives, even though both numbers meet the minimum
* ATAPI-4 spec of 73 and 54 nsec for UDMA 1 and 2 respectively.
* So the faster times are just commented out here. The good news is
* that the slower cycle time has very little affect on transfer
* performance.
*/
pci_read_config_byte(pdev, 0x48, &reg48);
pci_read_config_byte(pdev, 0x4A, &reg4a);
reg4a &= ~(3 << (4 * dn));
if (adev->dma_mode >= XFER_UDMA_0) {
reg48 |= 1 << dn;
#ifdef UDMA_TIMING_SET
reg4a |= ((adev->dma_mode - XFER_UDMA_0) << (4 * dn));
#endif
pio = 4;
} else {
pio = pio_map[adev->dma_mode - XFER_MW_DMA_0];
reg48 &= ~ (1 << dn);
}
pci_write_config_byte(pdev, 0x48, reg48);
pci_write_config_byte(pdev, 0x4A, reg4a);
it8172_set_pio_timing(ap, adev, pio);
}
static struct scsi_host_template it8172_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.max_sectors = ATA_MAX_SECTORS,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
};
static struct ata_port_operations it8172_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = it8172_set_piomode,
.set_dmamode = it8172_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = it8172_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.eng_timeout = ata_eng_timeout,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop
};
static int it8172_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static struct ata_port_info info = {
.sht = &it8172_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x06, /* No MWDMA0 support */
.udma_mask = 0x7,
.port_ops = &it8172_port_ops
};
static struct ata_port_info *port_info[2] = { &info, &info };
if ((!(PCI_FUNC(dev->devfn) & 1) ||
(!((dev->class >> 8) == PCI_CLASS_STORAGE_IDE))))
return -ENODEV; /* IT8172 is more than an IDE controller */
return ata_pci_init_one(dev, port_info, 2);
}
static struct pci_device_id it8172[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_IT8172G), },
{ 0, },
};
static struct pci_driver it8172_pci_driver = {
.name = DRV_NAME,
.id_table = it8172,
.probe = it8172_init_one,
.remove = ata_pci_remove_one
};
static int __init it8172_init(void)
{
return pci_register_driver(&it8172_pci_driver);
}
static void __exit it8172_exit(void)
{
pci_unregister_driver(&it8172_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for ITE IT8172");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, it8172);
MODULE_VERSION(DRV_VERSION);
module_init(it8172_init);
module_exit(it8172_exit);