forked from Minki/linux
ieee1394: move init_ohci1394_dma to drivers/firewire/
because drivers/ieee1394/ will be deleted. Additional changes: - add some #include directives - adjust to use firewire/ohci.h instead of ieee1394/ohci1394.h, replace struct ti_ohci by a minimal struct ohci, replace quadlet_t from ieee1394_types.h by u32 - two or three trivial stylistic changes - __iomem annotation Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This commit is contained in:
parent
cb655d0f3d
commit
1ef5b816c0
@ -13,3 +13,4 @@ obj-$(CONFIG_FIREWIRE_OHCI) += firewire-ohci.o
|
||||
obj-$(CONFIG_FIREWIRE_SBP2) += firewire-sbp2.o
|
||||
obj-$(CONFIG_FIREWIRE_NET) += firewire-net.o
|
||||
obj-$(CONFIG_FIREWIRE_NOSY) += nosy.o
|
||||
obj-$(CONFIG_PROVIDE_OHCI1394_DMA_INIT) += init_ohci1394_dma.o
|
||||
|
@ -32,23 +32,41 @@
|
||||
* Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
|
||||
*/
|
||||
|
||||
#include <linux/interrupt.h> /* for ohci1394.h */
|
||||
#include <linux/delay.h>
|
||||
#include <linux/io.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/pci.h> /* for PCI defines */
|
||||
#include <linux/init_ohci1394_dma.h>
|
||||
#include <linux/string.h>
|
||||
|
||||
#include <asm/pci-direct.h> /* for direct PCI config space access */
|
||||
#include <asm/fixmap.h>
|
||||
|
||||
#include "ieee1394_types.h"
|
||||
#include "ohci1394.h"
|
||||
#include <linux/init_ohci1394_dma.h>
|
||||
#include "ohci.h"
|
||||
|
||||
int __initdata init_ohci1394_dma_early;
|
||||
|
||||
struct ohci {
|
||||
void __iomem *registers;
|
||||
};
|
||||
|
||||
static inline void reg_write(const struct ohci *ohci, int offset, u32 data)
|
||||
{
|
||||
writel(data, ohci->registers + offset);
|
||||
}
|
||||
|
||||
static inline u32 reg_read(const struct ohci *ohci, int offset)
|
||||
{
|
||||
return readl(ohci->registers + offset);
|
||||
}
|
||||
|
||||
#define OHCI_LOOP_COUNT 100 /* Number of loops for reg read waits */
|
||||
|
||||
/* Reads a PHY register of an OHCI-1394 controller */
|
||||
static inline u8 __init get_phy_reg(struct ti_ohci *ohci, u8 addr)
|
||||
static inline u8 __init get_phy_reg(struct ohci *ohci, u8 addr)
|
||||
{
|
||||
int i;
|
||||
quadlet_t r;
|
||||
u32 r;
|
||||
|
||||
reg_write(ohci, OHCI1394_PhyControl, (addr << 8) | 0x00008000);
|
||||
|
||||
@ -63,22 +81,22 @@ static inline u8 __init get_phy_reg(struct ti_ohci *ohci, u8 addr)
|
||||
}
|
||||
|
||||
/* Writes to a PHY register of an OHCI-1394 controller */
|
||||
static inline void __init set_phy_reg(struct ti_ohci *ohci, u8 addr, u8 data)
|
||||
static inline void __init set_phy_reg(struct ohci *ohci, u8 addr, u8 data)
|
||||
{
|
||||
int i;
|
||||
|
||||
reg_write(ohci, OHCI1394_PhyControl, (addr << 8) | data | 0x00004000);
|
||||
|
||||
for (i = 0; i < OHCI_LOOP_COUNT; i++) {
|
||||
u32 r = reg_read(ohci, OHCI1394_PhyControl);
|
||||
if (!(r & 0x00004000))
|
||||
if (!(reg_read(ohci, OHCI1394_PhyControl) & 0x00004000))
|
||||
break;
|
||||
mdelay(1);
|
||||
}
|
||||
}
|
||||
|
||||
/* Resets an OHCI-1394 controller (for sane state before initialization) */
|
||||
static inline void __init init_ohci1394_soft_reset(struct ti_ohci *ohci) {
|
||||
static inline void __init init_ohci1394_soft_reset(struct ohci *ohci)
|
||||
{
|
||||
int i;
|
||||
|
||||
reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_softReset);
|
||||
@ -91,10 +109,14 @@ static inline void __init init_ohci1394_soft_reset(struct ti_ohci *ohci) {
|
||||
}
|
||||
}
|
||||
|
||||
#define OHCI1394_MAX_AT_REQ_RETRIES 0xf
|
||||
#define OHCI1394_MAX_AT_RESP_RETRIES 0x2
|
||||
#define OHCI1394_MAX_PHYS_RESP_RETRIES 0x8
|
||||
|
||||
/* Basic OHCI-1394 register and port inititalization */
|
||||
static inline void __init init_ohci1394_initialize(struct ti_ohci *ohci)
|
||||
static inline void __init init_ohci1394_initialize(struct ohci *ohci)
|
||||
{
|
||||
quadlet_t bus_options;
|
||||
u32 bus_options;
|
||||
int num_ports, i;
|
||||
|
||||
/* Put some defaults to these undefined bus options */
|
||||
@ -116,7 +138,7 @@ static inline void __init init_ohci1394_initialize(struct ti_ohci *ohci)
|
||||
|
||||
/* enable phys */
|
||||
reg_write(ohci, OHCI1394_LinkControlSet,
|
||||
OHCI1394_LinkControl_RcvPhyPkt);
|
||||
OHCI1394_LinkControl_rcvPhyPkt);
|
||||
|
||||
/* Don't accept phy packets into AR request context */
|
||||
reg_write(ohci, OHCI1394_LinkControlClear, 0x00000400);
|
||||
@ -128,7 +150,7 @@ static inline void __init init_ohci1394_initialize(struct ti_ohci *ohci)
|
||||
reg_write(ohci, OHCI1394_IsoXmitIntEventClear, 0xffffffff);
|
||||
|
||||
/* Accept asyncronous transfer requests from all nodes for now */
|
||||
reg_write(ohci,OHCI1394_AsReqFilterHiSet, 0x80000000);
|
||||
reg_write(ohci, OHCI1394_AsReqFilterHiSet, 0x80000000);
|
||||
|
||||
/* Specify asyncronous transfer retries */
|
||||
reg_write(ohci, OHCI1394_ATRetries,
|
||||
@ -137,7 +159,8 @@ static inline void __init init_ohci1394_initialize(struct ti_ohci *ohci)
|
||||
(OHCI1394_MAX_PHYS_RESP_RETRIES<<8));
|
||||
|
||||
/* We don't want hardware swapping */
|
||||
reg_write(ohci, OHCI1394_HCControlClear, OHCI1394_HCControl_noByteSwap);
|
||||
reg_write(ohci, OHCI1394_HCControlClear,
|
||||
OHCI1394_HCControl_noByteSwapData);
|
||||
|
||||
/* Enable link */
|
||||
reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_linkEnable);
|
||||
@ -164,11 +187,11 @@ static inline void __init init_ohci1394_initialize(struct ti_ohci *ohci)
|
||||
* has to be enabled after each bus reset when needed. We resort
|
||||
* to polling here because on early boot, we have no interrupts.
|
||||
*/
|
||||
static inline void __init init_ohci1394_wait_for_busresets(struct ti_ohci *ohci)
|
||||
static inline void __init init_ohci1394_wait_for_busresets(struct ohci *ohci)
|
||||
{
|
||||
int i, events;
|
||||
|
||||
for (i=0; i < 9; i++) {
|
||||
for (i = 0; i < 9; i++) {
|
||||
mdelay(200);
|
||||
events = reg_read(ohci, OHCI1394_IntEventSet);
|
||||
if (events & OHCI1394_busReset)
|
||||
@ -182,18 +205,18 @@ static inline void __init init_ohci1394_wait_for_busresets(struct ti_ohci *ohci)
|
||||
* This enables remote DMA access over IEEE1394 from every host for the low
|
||||
* 4GB of address space. DMA accesses above 4GB are not available currently.
|
||||
*/
|
||||
static inline void __init init_ohci1394_enable_physical_dma(struct ti_ohci *hci)
|
||||
static inline void __init init_ohci1394_enable_physical_dma(struct ohci *ohci)
|
||||
{
|
||||
reg_write(hci, OHCI1394_PhyReqFilterHiSet, 0xffffffff);
|
||||
reg_write(hci, OHCI1394_PhyReqFilterLoSet, 0xffffffff);
|
||||
reg_write(hci, OHCI1394_PhyUpperBound, 0xffff0000);
|
||||
reg_write(ohci, OHCI1394_PhyReqFilterHiSet, 0xffffffff);
|
||||
reg_write(ohci, OHCI1394_PhyReqFilterLoSet, 0xffffffff);
|
||||
reg_write(ohci, OHCI1394_PhyUpperBound, 0xffff0000);
|
||||
}
|
||||
|
||||
/**
|
||||
* init_ohci1394_reset_and_init_dma - init controller and enable DMA
|
||||
* This initializes the given controller and enables physical DMA engine in it.
|
||||
*/
|
||||
static inline void __init init_ohci1394_reset_and_init_dma(struct ti_ohci *ohci)
|
||||
static inline void __init init_ohci1394_reset_and_init_dma(struct ohci *ohci)
|
||||
{
|
||||
/* Start off with a soft reset, clears everything to a sane state. */
|
||||
init_ohci1394_soft_reset(ohci);
|
||||
@ -225,7 +248,7 @@ static inline void __init init_ohci1394_reset_and_init_dma(struct ti_ohci *ohci)
|
||||
static inline void __init init_ohci1394_controller(int num, int slot, int func)
|
||||
{
|
||||
unsigned long ohci_base;
|
||||
struct ti_ohci ohci;
|
||||
struct ohci ohci;
|
||||
|
||||
printk(KERN_INFO "init_ohci1394_dma: initializing OHCI-1394"
|
||||
" at %02x:%02x.%x\n", num, slot, func);
|
||||
@ -235,7 +258,7 @@ static inline void __init init_ohci1394_controller(int num, int slot, int func)
|
||||
|
||||
set_fixmap_nocache(FIX_OHCI1394_BASE, ohci_base);
|
||||
|
||||
ohci.registers = (void *)fix_to_virt(FIX_OHCI1394_BASE);
|
||||
ohci.registers = (void __iomem *)fix_to_virt(FIX_OHCI1394_BASE);
|
||||
|
||||
init_ohci1394_reset_and_init_dma(&ohci);
|
||||
}
|
||||
@ -247,6 +270,7 @@ static inline void __init init_ohci1394_controller(int num, int slot, int func)
|
||||
void __init init_ohci1394_dma_on_all_controllers(void)
|
||||
{
|
||||
int num, slot, func;
|
||||
u32 class;
|
||||
|
||||
if (!early_pci_allowed())
|
||||
return;
|
||||
@ -255,9 +279,9 @@ void __init init_ohci1394_dma_on_all_controllers(void)
|
||||
for (num = 0; num < 32; num++) {
|
||||
for (slot = 0; slot < 32; slot++) {
|
||||
for (func = 0; func < 8; func++) {
|
||||
u32 class = read_pci_config(num,slot,func,
|
||||
class = read_pci_config(num, slot, func,
|
||||
PCI_CLASS_REVISION);
|
||||
if ((class == 0xffffffff))
|
||||
if (class == 0xffffffff)
|
||||
continue; /* No device at this func */
|
||||
|
||||
if (class>>8 != PCI_CLASS_SERIAL_FIREWIRE_OHCI)
|
@ -14,5 +14,3 @@ obj-$(CONFIG_IEEE1394_RAWIO) += raw1394.o
|
||||
obj-$(CONFIG_IEEE1394_SBP2) += sbp2.o
|
||||
obj-$(CONFIG_IEEE1394_DV1394) += dv1394.o
|
||||
obj-$(CONFIG_IEEE1394_ETH1394) += eth1394.o
|
||||
|
||||
obj-$(CONFIG_PROVIDE_OHCI1394_DMA_INIT) += init_ohci1394_dma.o
|
||||
|
Loading…
Reference in New Issue
Block a user