diff --git a/Documentation/devicetree/bindings/arm/qcom.txt b/Documentation/devicetree/bindings/arm/qcom.txt index 3e24518c6678..43abf4e0a0a5 100644 --- a/Documentation/devicetree/bindings/arm/qcom.txt +++ b/Documentation/devicetree/bindings/arm/qcom.txt @@ -22,6 +22,7 @@ The 'SoC' element must be one of the following strings: msm8916 msm8974 msm8996 + mdm9615 The 'board' element must be one of the following strings: diff --git a/Documentation/devicetree/bindings/arm/swir.txt b/Documentation/devicetree/bindings/arm/swir.txt new file mode 100644 index 000000000000..042be73a95d3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/swir.txt @@ -0,0 +1,12 @@ +Sierra Wireless Modules device tree bindings +-------------------------------------------- + +Supported Modules : + - WP8548 : Includes MDM9615 and PM8018 in a module + +Sierra Wireless modules shall have the following properties : + Required root node property + - compatible: "swir,wp8548" for the WP8548 CF3 Module + +Board compatible values: + - "swir,mangoh-green-wp8548" for the mangOH green board with the WP8548 module diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index befa3141fafb..5a9fb0ea6566 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -633,7 +633,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-msm8660-surf.dtb \ qcom-msm8960-cdp.dtb \ qcom-msm8974-lge-nexus5-hammerhead.dtb \ - qcom-msm8974-sony-xperia-honami.dtb + qcom-msm8974-sony-xperia-honami.dtb \ + qcom-mdm9615-wp8548-mangoh-green.dtb dtb-$(CONFIG_ARCH_REALVIEW) += \ arm-realview-pb1176.dtb \ arm-realview-pb11mp.dtb \ diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts index 6c0038398ef2..4b8872cc8bf9 100644 --- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts +++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts @@ -51,6 +51,29 @@ regulator-boot-on; }; + /* GPIO controlled ethernet power regulator */ + dragon_veth: xc622a331mrg { + compatible = "regulator-fixed"; + regulator-name = "XC6222A331MR-G"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vph>; + gpio = <&pm8058_gpio 40 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_veth_gpios>; + regulator-always-on; + }; + + /* VDDvario fixed regulator */ + dragon_vario: nds332p { + compatible = "regulator-fixed"; + regulator-name = "NDS332P"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&pm8058_s3>; + }; + /* This is a levelshifter for SDCC5 */ dragon_vio_txb: txb0104rgyr { compatible = "regulator-fixed"; @@ -167,6 +190,36 @@ bias-pull-up; }; }; + + dragon_ebi2_pins: ebi2 { + /* + * Pins used by EBI2 on the Dragonboard, actually only + * CS2 is used by a real peripheral. CS0 is just + * routed to a test point. + */ + mux0 { + pins = + /* "gpio39", CS1A_N this is not good to mux */ + "gpio40", /* CS2A_N */ + "gpio134"; /* CS0_N testpoint TP29 */ + function = "ebi2cs"; + }; + mux1 { + pins = + /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */ + "gpio123", "gpio124", "gpio125", "gpio126", + "gpio127", "gpio128", "gpio129", "gpio130", + /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */ + "gpio135", "gpio136", "gpio137", "gpio138", + "gpio139", "gpio140", "gpio141", "gpio142", + "gpio143", "gpio144", "gpio145", "gpio146", + "gpio147", "gpio148", "gpio149", "gpio150", + "gpio151", /* EBI2_OE_N */ + "gpio153", /* EBI2_ADV */ + "gpio157"; /* EBI2_WE_N */ + function = "ebi2"; + }; + }; }; qcom,ssbi@500000 { @@ -201,6 +254,15 @@ }; gpio@150 { + dragon_ethernet_gpios: ethernet-gpios { + pinconf { + pins = "gpio7"; + function = "normal"; + input-enable; + bias-disable; + power-source = ; + }; + }; dragon_bmp085_gpios: bmp085-gpios { pinconf { pins = "gpio16"; @@ -238,6 +300,14 @@ power-source = ; }; }; + dragon_veth_gpios: veth-gpios { + pinconf { + pins = "gpio40"; + function = "normal"; + bias-disable; + drive-push-pull; + }; + }; }; led@48 { @@ -322,6 +392,55 @@ }; }; + external-bus@1a100000 { + /* The EBI2 will instantiate first, then populate its children */ + status = "ok"; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_ebi2_pins>; + + /* + * An on-board SMSC LAN9221 chip for "debug ethernet", + * which is actually just an ordinary ethernet on the + * EBI2. This has a 25MHz chrystal next to it, so no + * clocking is needed. + */ + ethernet-ebi2@2,0 { + compatible = "smsc,lan9221", "smsc,lan9115"; + reg = <2 0x0 0x100>; + /* + * GPIO7 has interrupt 198 on the PM8058 + * The second interrupt is the PME interrupt + * for network wakeup, connected to the TLMM. + */ + interrupts-extended = <&pmicintc 198 IRQ_TYPE_EDGE_FALLING>, + <&tlmm 29 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>; + vdd33a-supply = <&dragon_veth>; + vddvario-supply = <&dragon_vario>; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_ethernet_gpios>; + phy-mode = "mii"; + reg-io-width = <2>; + smsc,force-external-phy; + /* IRQ on edge falling = active low */ + smsc,irq-active-low; + smsc,irq-push-pull; + + /* + * SLOW chipselect config + * Delay 9 cycles (140ns@64MHz) between SMSC + * LAN9221 Ethernet controller reads and writes + * on CS2. + */ + qcom,xmem-recovery-cycles = <0>; + qcom,xmem-write-hold-cycles = <3>; + qcom,xmem-write-delta-cycles = <31>; + qcom,xmem-read-delta-cycles = <28>; + qcom,xmem-write-wait-cycles = <9>; + qcom,xmem-read-wait-cycles = <9>; + }; + }; + rpm@104000 { /* * Set up of the PMIC RPM regulators for this board diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts index b72e09506448..e39440a86739 100644 --- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts +++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts @@ -15,6 +15,20 @@ stdout-path = "serial0:115200n8"; }; + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ramoops@88d00000{ + compatible = "ramoops"; + reg = <0x88d00000 0x100000>; + record-size = <0x00020000>; + console-size = <0x00020000>; + ftrace-size = <0x00020000>; + }; + }; + ext_3p3v: regulator-fixed@1 { compatible = "regulator-fixed"; regulator-min-microvolt = <3300000>; @@ -99,6 +113,7 @@ l2 { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; + regulator-always-on; }; /* msm_otg-HSUSB_3p3 */ @@ -133,13 +148,14 @@ regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; bias-pull-down; + regulator-always-on; }; /* pwm_power for backlight */ l17 { regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3600000>; - bias-pull-down; + regulator-max-microvolt = <3000000>; + regulator-always-on; }; /* camera, qdsp6 */ @@ -184,6 +200,63 @@ }; }; + mdp@5100000 { + status = "okay"; + ports { + port@1 { + mdp_dsi1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + }; + + dsi0: mdss_dsi@4700000 { + status = "okay"; + vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/ + vdd-supply = <&pm8921_l8>; + vddio-supply = <&pm8921_lvs7>; + avdd-supply = <&pm8921_l11>; + vcss-supply = <&ext_3p3v>; + + panel@0 { + reg = <0>; + compatible = "jdi,lt070me05000"; + + vddp-supply = <&pm8921_l17>; + iovcc-supply = <&pm8921_lvs7>; + + enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>; + reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>; + dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; + ports { + port@0 { + dsi0_in: endpoint { + remote-endpoint = <&mdp_dsi1_out>; + }; + }; + + port@1 { + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; + }; + + dsi-phy@4700200 { + status = "okay"; + vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/ + }; + gsbi@16200000 { status = "okay"; qcom,mode = ; diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts index 2eeb0904eaa7..3d37cab3b9a9 100644 --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts @@ -43,6 +43,17 @@ }; }; + hdmi-out { + compatible = "hdmi-connector"; + type = "d"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&hdmi_out>; + }; + }; + }; + soc { pinctrl@800000 { card_detect: card_detect { @@ -64,6 +75,25 @@ bias-disable; }; }; + + hdmi_pinctrl: hdmi-pinctrl { + mux { + pins = "gpio70", "gpio71", "gpio72"; + function = "hdmi"; + }; + + pinconf_ddc { + pins = "gpio70", "gpio71"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf_hpd { + pins = "gpio72"; + bias-pull-down; + drive-strength = <16>; + }; + }; }; rpm@108000 { @@ -329,5 +359,49 @@ mmc-pwrseq = <&sdcc4_pwrseq>; }; }; + + hdmi-tx@4a00000 { + status = "okay"; + + core-vdda-supply = <&pm8921_hdmi_switch>; + hdmi-mux-supply = <&ext_3p3v>; + + hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pinctrl>; + + ports { + port@0 { + endpoint { + remote-endpoint = <&mdp_dtv_out>; + }; + }; + + port@1 { + endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; + + hdmi-phy@4a00400 { + status = "okay"; + + core-vdda-supply = <&pm8921_hdmi_switch>; + }; + + mdp@5100000 { + status = "okay"; + + ports { + port@3 { + endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + }; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index 1dbe697b2e90..268bd470c865 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -1060,6 +1060,231 @@ reg = <0x1a400000 0x100>; }; + gpu: adreno-3xx@4300000 { + compatible = "qcom,adreno-3xx"; + reg = <0x04300000 0x20000>; + reg-names = "kgsl_3d0_reg_memory"; + interrupts = ; + interrupt-names = "kgsl_3d0_irq"; + clock-names = + "core_clk", + "iface_clk", + "mem_clk", + "mem_iface_clk"; + clocks = + <&mmcc GFX3D_CLK>, + <&mmcc GFX3D_AHB_CLK>, + <&mmcc GFX3D_AXI_CLK>, + <&mmcc MMSS_IMEM_AHB_CLK>; + qcom,chipid = <0x03020002>; + + iommus = <&gfx3d 0 + &gfx3d 1 + &gfx3d 2 + &gfx3d 3 + &gfx3d 4 + &gfx3d 5 + &gfx3d 6 + &gfx3d 7 + &gfx3d 8 + &gfx3d 9 + &gfx3d 10 + &gfx3d 11 + &gfx3d 12 + &gfx3d 13 + &gfx3d 14 + &gfx3d 15 + &gfx3d 16 + &gfx3d 17 + &gfx3d 18 + &gfx3d 19 + &gfx3d 20 + &gfx3d 21 + &gfx3d 22 + &gfx3d 23 + &gfx3d 24 + &gfx3d 25 + &gfx3d 26 + &gfx3d 27 + &gfx3d 28 + &gfx3d 29 + &gfx3d 30 + &gfx3d 31 + &gfx3d1 0 + &gfx3d1 1 + &gfx3d1 2 + &gfx3d1 3 + &gfx3d1 4 + &gfx3d1 5 + &gfx3d1 6 + &gfx3d1 7 + &gfx3d1 8 + &gfx3d1 9 + &gfx3d1 10 + &gfx3d1 11 + &gfx3d1 12 + &gfx3d1 13 + &gfx3d1 14 + &gfx3d1 15 + &gfx3d1 16 + &gfx3d1 17 + &gfx3d1 18 + &gfx3d1 19 + &gfx3d1 20 + &gfx3d1 21 + &gfx3d1 22 + &gfx3d1 23 + &gfx3d1 24 + &gfx3d1 25 + &gfx3d1 26 + &gfx3d1 27 + &gfx3d1 28 + &gfx3d1 29 + &gfx3d1 30 + &gfx3d1 31>; + + qcom,gpu-pwrlevels { + compatible = "qcom,gpu-pwrlevels"; + qcom,gpu-pwrlevel@0 { + qcom,gpu-freq = <450000000>; + }; + qcom,gpu-pwrlevel@1 { + qcom,gpu-freq = <27000000>; + }; + }; + }; + + mmss_sfpb: syscon@5700000 { + compatible = "syscon"; + reg = <0x5700000 0x70>; + }; + + dsi0: mdss_dsi@4700000 { + compatible = "qcom,mdss-dsi-ctrl"; + label = "MDSS DSI CTRL->0"; + #address-cells = <1>; + #size-cells = <0>; + interrupts = ; + reg = <0x04700000 0x200>; + reg-names = "dsi_ctrl"; + + clocks = <&mmcc DSI_M_AHB_CLK>, + <&mmcc DSI_S_AHB_CLK>, + <&mmcc AMP_AHB_CLK>, + <&mmcc DSI_CLK>, + <&mmcc DSI1_BYTE_CLK>, + <&mmcc DSI_PIXEL_CLK>, + <&mmcc DSI1_ESC_CLK>; + clock-names = "iface_clk", "bus_clk", "core_mmss_clk", + "src_clk", "byte_clk", "pixel_clk", + "core_clk"; + + assigned-clocks = <&mmcc DSI1_BYTE_SRC>, + <&mmcc DSI1_ESC_SRC>, + <&mmcc DSI_SRC>, + <&mmcc DSI_PIXEL_SRC>; + assigned-clock-parents = <&dsi0_phy 0>, + <&dsi0_phy 0>, + <&dsi0_phy 1>, + <&dsi0_phy 1>; + syscon-sfpb = <&mmss_sfpb>; + phys = <&dsi0_phy>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + }; + }; + }; + }; + + + dsi0_phy: dsi-phy@4700200 { + compatible = "qcom,dsi-phy-28nm-8960"; + #clock-cells = <1>; + + reg = <0x04700200 0x100>, + <0x04700300 0x200>, + <0x04700500 0x5c>; + reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator"; + clock-names = "iface_clk"; + clocks = <&mmcc DSI_M_AHB_CLK>; + }; + + + mdp_port0: iommu@7500000 { + compatible = "qcom,apq8064-iommu"; + #iommu-cells = <1>; + clock-names = + "smmu_pclk", + "iommu_clk"; + clocks = + <&mmcc SMMU_AHB_CLK>, + <&mmcc MDP_AXI_CLK>; + reg = <0x07500000 0x100000>; + interrupts = + , + ; + qcom,ncb = <2>; + }; + + mdp_port1: iommu@7600000 { + compatible = "qcom,apq8064-iommu"; + #iommu-cells = <1>; + clock-names = + "smmu_pclk", + "iommu_clk"; + clocks = + <&mmcc SMMU_AHB_CLK>, + <&mmcc MDP_AXI_CLK>; + reg = <0x07600000 0x100000>; + interrupts = + , + ; + qcom,ncb = <2>; + }; + + gfx3d: iommu@7c00000 { + compatible = "qcom,apq8064-iommu"; + #iommu-cells = <1>; + clock-names = + "smmu_pclk", + "iommu_clk"; + clocks = + <&mmcc SMMU_AHB_CLK>, + <&mmcc GFX3D_AXI_CLK>; + reg = <0x07c00000 0x100000>; + interrupts = + , + ; + qcom,ncb = <3>; + }; + + gfx3d1: iommu@7d00000 { + compatible = "qcom,apq8064-iommu"; + #iommu-cells = <1>; + clock-names = + "smmu_pclk", + "iommu_clk"; + clocks = + <&mmcc SMMU_AHB_CLK>, + <&mmcc GFX3D_AXI_CLK>; + reg = <0x07d00000 0x100000>; + interrupts = + , + ; + qcom,ncb = <3>; + }; + pcie: pci@1b500000 { compatible = "qcom,pcie-apq8064", "snps,dw-pcie"; reg = <0x1b500000 0x1000 @@ -1095,6 +1320,102 @@ reset-names = "axi", "ahb", "por", "pci", "phy"; status = "disabled"; }; + + hdmi: hdmi-tx@4a00000 { + compatible = "qcom,hdmi-tx-8960"; + reg = <0x04a00000 0x2f0>; + reg-names = "core_physical"; + interrupts = ; + clocks = <&mmcc HDMI_APP_CLK>, + <&mmcc HDMI_M_AHB_CLK>, + <&mmcc HDMI_S_AHB_CLK>; + clock-names = "core_clk", + "master_iface_clk", + "slave_iface_clk"; + + phys = <&hdmi_phy>; + phy-names = "hdmi-phy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + hdmi_in: endpoint { + }; + }; + + port@1 { + reg = <1>; + hdmi_out: endpoint { + }; + }; + }; + }; + + hdmi_phy: hdmi-phy@4a00400 { + compatible = "qcom,hdmi-phy-8960"; + reg = <0x4a00400 0x60>, + <0x4a00500 0x100>; + reg-names = "hdmi_phy", + "hdmi_pll"; + + clocks = <&mmcc HDMI_S_AHB_CLK>; + clock-names = "slave_iface_clk"; + }; + + mdp: mdp@5100000 { + compatible = "qcom,mdp4"; + reg = <0x05100000 0xf0000>; + interrupts = ; + clocks = <&mmcc MDP_CLK>, + <&mmcc MDP_AHB_CLK>, + <&mmcc MDP_AXI_CLK>, + <&mmcc MDP_LUT_CLK>, + <&mmcc HDMI_TV_CLK>, + <&mmcc MDP_TV_CLK>; + clock-names = "core_clk", + "iface_clk", + "bus_clk", + "lut_clk", + "hdmi_clk", + "tv_clk"; + + iommus = <&mdp_port0 0 + &mdp_port0 2 + &mdp_port1 0 + &mdp_port1 2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp_lvds_out: endpoint { + }; + }; + + port@1 { + reg = <1>; + mdp_dsi1_out: endpoint { + }; + }; + + port@2 { + reg = <2>; + mdp_dsi2_out: endpoint { + }; + }; + + port@3 { + reg = <3>; + mdp_dtv_out: endpoint { + }; + }; + }; + }; }; }; #include "qcom-apq8064-pins.dtsi" diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts b/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts new file mode 100644 index 000000000000..26160c324802 --- /dev/null +++ b/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts @@ -0,0 +1,281 @@ +/* + * Device Tree Source for mangOH Green Board with WP8548 Module + * + * Copyright (C) 2016 BayLibre, SAS. + * Author : Neil Armstrong + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include + +#include "qcom-mdm9615-wp8548.dtsi" +#include +#include + +/ { + model = "MangOH Green with WP8548 Module"; + compatible = "swir,mangoh-green-wp8548", "swir,wp8548", "qcom,mdm9615"; + + aliases { + spi0 = &gsbi3_spi; + serial0 = &gsbi4_serial; + serial1 = &gsbi5_serial; + i2c0 = &gsbi5_i2c; + mmc0 = &sdcc1; + }; + + chosen { + stdout-path = "serial1:115200n8"; + }; +}; + +&msmgpio { + /* MangOH GPIO Mapping : + * - 2 : GPIOEXP_INT2 + * - 7 : IOT1_GPIO2 + * - 8 : IOT0_GPIO4 + * - 13: IOT0_GPIO3 + * - 21: IOT1_GPIO4 + * - 22: IOT2_GPIO1 + * - 23: IOT2_GPIO2 + * - 24: IOT2_GPIO3 + * - 25: IOT1_GPIO1 + * - 32: IOT1_GPIO3 + * - 33: IOT0_GPIO2 + * - 42: IOT0_GPIO1 and SD Card Detect + */ + + gpioext1_pins: gpioext1_pins { + pins { + pins = "gpio2"; + function = "gpio"; + input-enable; + bias-disable; + }; + }; + + sdc_cd_pins: sdc_cd_pins { + pins { + pins = "gpio42"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; +}; + +&gsbi3_spi { + spi@0 { + compatible = "swir,mangoh-iotport-spi", "spidev"; + spi-max-frequency = <24000000>; + reg = <0>; + }; +}; + +&gsbi5_i2c { + mux@71 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x71>; + + i2c_iot0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c_iot1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + + i2c_iot2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + usbhub: hub@8 { + compatible = "smsc,usb3503a"; + reg = <0x8>; + connect-gpios = <&gpioext2 1 GPIO_ACTIVE_HIGH>; + intn-gpios = <&gpioext2 0 GPIO_ACTIVE_LOW>; + initial-mode = <1>; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + gpioext0: gpio@3e { + /* GPIO Expander 0 Mapping : + * - 0: ARDUINO_RESET_Level shift + * - 1: BattChrgr_PG_N + * - 2: BattGauge_GPIO + * - 3: LED_ON (out active high) + * - 4: ATmega_reset_GPIO + * - 5: X + * - 6: PCM_ANALOG_SELECT (out active high) + * - 7: X + * - 8: Board_rev_res1 (in) + * - 9: Board_rev_res2 (in) + * - 10: UART_EXP1_ENn (out active low / pull-down) + * - 11: UART_EXP1_IN (out pull-down) + * - 12: UART_EXP2_IN (out pull-down) + * - 13: SDIO_SEL (out pull-down) + * - 14: SPI_EXP1_ENn (out active low / pull-down) + * - 15: SPI_EXP1_IN (out pull-down) + */ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1509q"; + reg = <0x3e>; + interrupt-parent = <&gpioext1>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + + probe-reset; + + gpio-controller; + interrupt-controller; + }; + }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + + gpioext1: gpio@3f { + /* GPIO Expander 1 Mapping : + * - 0: GPIOEXP_INT1 + * - 1: Battery detect + * - 2: GPIO_SCF3_RESET + * - 3: LED_CARD_DETECT_IOT0 (in) + * - 4: LED_CARD_DETECT_IOT1 (in) + * - 5: LED_CARD_DETECT_IOT2 (in) + * - 6: UIM2_PWM_SELECT + * - 7: UIM2_M2_S_SELECT + * - 8: TP900 + * - 9: SENSOR_INT1 (in) + * - 10: SENSOR_INT2 (in) + * - 11: CARD_DETECT_IOT0 (in pull-up) + * - 12: CARD_DETECT_IOT2 (in pull-up) + * - 13: CARD_DETECT_IOT1 (in pull-up) + * - 14: GPIOEXP_INT3 (in active low / pull-up) + * - 15: BattChrgr_INT_N + */ + pinctrl-0 = <&gpioext1_pins>; + pinctrl-names = "default"; + + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1509q"; + reg = <0x3f>; + interrupt-parent = <&msmgpio>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + + probe-reset; + + gpio-controller; + interrupt-controller; + }; + }; + + i2c@6 { + #address-cells = <1>; + #size-cells = <0>; + reg = <6>; + + gpioext2: gpio@70 { + /* GPIO Expander 2 Mapping : + * - 0: USB_HUB_INTn + * - 1: HUB_CONNECT + * - 2: GPIO_IOT2_RESET (out active low / pull-up) + * - 3: GPIO_IOT1_RESET (out active low / pull-up) + * - 4: GPIO_IOT0_RESET (out active low / pull-up) + * - 5: TP901 + * - 6: TP902 + * - 7: TP903 + * - 8: UART_EXP2_ENn (out active low / pull-down) + * - 9: PCM_EXP1_ENn (out active low) + * - 10: PCM_EXP1_SEL (out) + * - 11: ARD_FTDI + * - 12: TP904 + * - 13: TP905 + * - 14: TP906 + * - 15: RS232_Enable (out active high / pull-up) + */ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1509q"; + reg = <0x70>; + interrupt-parent = <&gpioext1>; + interrupts = <14 IRQ_TYPE_EDGE_FALLING>; + + probe-reset; + + gpio-controller; + interrupt-controller; + }; + }; + + i2c@7 { + #address-cells = <1>; + #size-cells = <0>; + reg = <7>; + }; + }; +}; + +&sdcc1 { + pinctrl-0 = <&sdc_cd_pins>; + pinctrl-names = "default"; + disable-wp; + cd-gpios = <&msmgpio 42 GPIO_ACTIVE_LOW>; /* Active low CD */ +}; diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi new file mode 100644 index 000000000000..7869898e392d --- /dev/null +++ b/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi @@ -0,0 +1,170 @@ +/* + * Device Tree Source for Sierra Wireless WP8548 Module + * + * Copyright (C) 2016 BayLibre, SAS. + * Author : Neil Armstrong + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "qcom-mdm9615.dtsi" + +/ { + model = "Sierra Wireless WP8548 Module"; + compatible = "swir,wp8548", "qcom,mdm9615"; + + memory { + reg = <0x48000000 0x7F00000>; + }; +}; + +&msmgpio { + pinctrl-0 = <&reset_out_pins>; + pinctrl-names = "default"; + + gsbi3_pins: gsbi3_pins { + mux { + pins = "gpio8", "gpio9", "gpio10", "gpio11"; + function = "gsbi3"; + drive-strength = <8>; + bias-disable; + }; + }; + + gsbi4_pins: gsbi4_pins { + mux { + pins = "gpio12", "gpio13", "gpio14", "gpio15"; + function = "gsbi4"; + drive-strength = <8>; + bias-disable; + }; + }; + + gsbi5_i2c_pins: gsbi5_i2c_pins { + pin16 { + pins = "gpio16"; + function = "gsbi5_i2c"; + drive-strength = <8>; + bias-disable; + }; + + pin17 { + pins = "gpio17"; + function = "gsbi5_i2c"; + drive-strength = <2>; + bias-disable; + }; + }; + + gsbi5_uart_pins: gsbi5_uart_pins { + mux { + pins = "gpio18", "gpio19"; + function = "gsbi5_uart"; + drive-strength = <8>; + bias-disable; + }; + }; + + reset_out_pins: reset_out_pins { + pins { + pins = "gpio66"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + output-high; + }; + }; +}; + +&pmicgpio { + usb_vbus_5v_pins: usb_vbus_5v_pins { + pins = "gpio4"; + function = "normal"; + output-high; + bias-disable; + qcom,drive-strength = <1>; + power-source = <2>; + }; +}; + +&gsbi3 { + status = "ok"; + qcom,mode = ; +}; + +&gsbi3_spi { + status = "ok"; + pinctrl-0 = <&gsbi3_pins>; + pinctrl-names = "default"; + assigned-clocks = <&gcc GSBI3_QUP_CLK>; + assigned-clock-rates = <24000000>; +}; + +&gsbi4 { + status = "ok"; + qcom,mode = ; +}; + +&gsbi4_serial { + status = "ok"; + pinctrl-0 = <&gsbi4_pins>; + pinctrl-names = "default"; +}; + +&gsbi5 { + status = "ok"; + qcom,mode = ; +}; + +&gsbi5_i2c { + status = "ok"; + clock-frequency = <200000>; + pinctrl-0 = <&gsbi5_i2c_pins>; + pinctrl-names = "default"; +}; + +&gsbi5_serial { + status = "ok"; + pinctrl-0 = <&gsbi5_uart_pins>; + pinctrl-names = "default"; +}; + +&sdcc1 { + status = "ok"; +}; diff --git a/arch/arm/boot/dts/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom-mdm9615.dtsi new file mode 100644 index 000000000000..5ae4ec59e6ea --- /dev/null +++ b/arch/arm/boot/dts/qcom-mdm9615.dtsi @@ -0,0 +1,557 @@ +/* + * Device Tree Source for Qualcomm MDM9615 SoC + * + * Copyright (C) 2016 BayLibre, SAS. + * Author : Neil Armstrong + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +/include/ "skeleton.dtsi" + +#include +#include +#include +#include +#include + +/ { + model = "Qualcomm MDM9615"; + compatible = "qcom,mdm9615"; + interrupt-parent = <&intc>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + compatible = "arm,cortex-a5"; + device_type = "cpu"; + next-level-cache = <&L2>; + }; + }; + + cpu-pmu { + compatible = "arm,cortex-a5-pmu"; + interrupts = ; + }; + + clocks { + cxo_board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + }; + }; + + regulators { + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + regulator-always-on; + }; + }; + + soc: soc { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "simple-bus"; + + L2: l2-cache@2040000 { + compatible = "arm,pl310-cache"; + reg = <0x02040000 0x1000>; + arm,data-latency = <2 2 0>; + cache-unified; + cache-level = <2>; + }; + + intc: interrupt-controller@2000000 { + compatible = "qcom,msm-qgic2"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x02000000 0x1000>, + <0x02002000 0x1000>; + }; + + timer@200a000 { + compatible = "qcom,kpss-timer", "qcom,msm-timer"; + interrupts = , + , + ; + reg = <0x0200a000 0x100>; + clock-frequency = <27000000>, + <32768>; + cpu-offset = <0x80000>; + }; + + msmgpio: pinctrl@800000 { + compatible = "qcom,mdm9615-pinctrl"; + gpio-controller; + #gpio-cells = <2>; + interrupts = ; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x800000 0x4000>; + }; + + gcc: clock-controller@900000 { + compatible = "qcom,gcc-mdm9615"; + #clock-cells = <1>; + #reset-cells = <1>; + reg = <0x900000 0x4000>; + }; + + lcc: clock-controller@28000000 { + compatible = "qcom,lcc-mdm9615"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + l2cc: clock-controller@2011000 { + compatible = "syscon"; + reg = <0x02011000 0x1000>; + }; + + rng@1a500000 { + compatible = "qcom,prng"; + reg = <0x1a500000 0x200>; + clocks = <&gcc PRNG_CLK>; + clock-names = "core"; + assigned-clocks = <&gcc PRNG_CLK>; + assigned-clock-rates = <32000000>; + }; + + gsbi2: gsbi@16100000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <2>; + reg = <0x16100000 0x100>; + clocks = <&gcc GSBI2_H_CLK>; + clock-names = "iface"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gsbi2_i2c: i2c@16180000 { + compatible = "qcom,i2c-qup-v1.1.1"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x16180000 0x1000>; + interrupts = ; + + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + }; + + gsbi3: gsbi@16200000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <3>; + reg = <0x16200000 0x100>; + clocks = <&gcc GSBI3_H_CLK>; + clock-names = "iface"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gsbi3_spi: spi@16280000 { + compatible = "qcom,spi-qup-v1.1.1"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x16280000 0x1000>; + interrupts = ; + spi-max-frequency = <24000000>; + + clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + }; + + gsbi4: gsbi@16300000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <4>; + reg = <0x16300000 0x100>; + clocks = <&gcc GSBI4_H_CLK>; + clock-names = "iface"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + syscon-tcsr = <&tcsr>; + + gsbi4_serial: serial@16340000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x16340000 0x1000>, + <0x16300000 0x1000>; + interrupts = ; + clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + }; + + gsbi5: gsbi@16400000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <5>; + reg = <0x16400000 0x100>; + clocks = <&gcc GSBI5_H_CLK>; + clock-names = "iface"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + syscon-tcsr = <&tcsr>; + + gsbi5_i2c: i2c@16480000 { + compatible = "qcom,i2c-qup-v1.1.1"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x16480000 0x1000>; + interrupts = ; + + /* QUP clock is not initialized, set rate */ + assigned-clocks = <&gcc GSBI5_QUP_CLK>; + assigned-clock-rates = <24000000>; + + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + gsbi5_serial: serial@16440000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x16440000 0x1000>, + <0x16400000 0x1000>; + interrupts = ; + clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + }; + + qcom,ssbi@500000 { + compatible = "qcom,ssbi"; + reg = <0x500000 0x1000>; + qcom,controller-type = "pmic-arbiter"; + + pmicintc: pmic@0 { + compatible = "qcom,pm8018", "qcom,pm8921"; + interrupts = ; + #interrupt-cells = <2>; + interrupt-controller; + #address-cells = <1>; + #size-cells = <0>; + + pwrkey@1c { + compatible = "qcom,pm8018-pwrkey", "qcom,pm8921-pwrkey"; + reg = <0x1c>; + interrupt-parent = <&pmicintc>; + interrupts = <50 IRQ_TYPE_EDGE_RISING>, + <51 IRQ_TYPE_EDGE_RISING>; + debounce = <15625>; + pull-up; + }; + + pmicmpp: mpp@50 { + compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp"; + interrupt-parent = <&pmicintc>; + interrupts = <24 IRQ_TYPE_NONE>, + <25 IRQ_TYPE_NONE>, + <26 IRQ_TYPE_NONE>, + <27 IRQ_TYPE_NONE>, + <28 IRQ_TYPE_NONE>, + <29 IRQ_TYPE_NONE>; + reg = <0x50>; + gpio-controller; + #gpio-cells = <2>; + }; + + rtc@11d { + compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc"; + interrupt-parent = <&pmicintc>; + interrupts = <39 IRQ_TYPE_EDGE_RISING>; + reg = <0x11d>; + allow-set-time; + }; + + pmicgpio: gpio@150 { + compatible = "qcom,pm8018-gpio", "qcom,ssbi-gpio"; + interrupt-parent = <&pmicintc>; + interrupts = <24 IRQ_TYPE_NONE>, + <25 IRQ_TYPE_NONE>, + <26 IRQ_TYPE_NONE>, + <27 IRQ_TYPE_NONE>, + <28 IRQ_TYPE_NONE>, + <29 IRQ_TYPE_NONE>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + }; + + sdcc1bam: dma@12182000{ + compatible = "qcom,bam-v1.3.0"; + reg = <0x12182000 0x8000>; + interrupts = ; + clocks = <&gcc SDC1_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + sdcc2bam: dma@12142000{ + compatible = "qcom,bam-v1.3.0"; + reg = <0x12142000 0x8000>; + interrupts = ; + clocks = <&gcc SDC2_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + amba { + compatible = "arm,amba-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + sdcc1: sdcc@12180000 { + status = "disabled"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + reg = <0x12180000 0x2000>; + interrupts = ; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + max-frequency = <48000000>; + cap-sd-highspeed; + cap-mmc-highspeed; + vmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; + dma-names = "tx", "rx"; + assigned-clocks = <&gcc SDC1_CLK>; + assigned-clock-rates = <400000>; + }; + + sdcc2: sdcc@12140000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + status = "disabled"; + reg = <0x12140000 0x2000>; + interrupts = ; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <48000000>; + no-1-8-v; + vmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc2bam 2>, <&sdcc2bam 1>; + dma-names = "tx", "rx"; + assigned-clocks = <&gcc SDC2_CLK>; + assigned-clock-rates = <400000>; + }; + }; + + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-mdm9615", "syscon"; + reg = <0x1a400000 0x100>; + }; + + rpm: rpm@108000 { + compatible = "qcom,rpm-mdm9615"; + reg = <0x108000 0x1000>; + + qcom,ipc = <&l2cc 0x8 2>; + + interrupts = , + , + ; + interrupt-names = "ack", "err", "wakeup"; + + regulators { + compatible = "qcom,rpm-pm8018-regulators"; + + vin_lvs1-supply = <&pm8018_s3>; + + vdd_l7-supply = <&pm8018_s4>; + vdd_l8-supply = <&pm8018_s3>; + vdd_l9_l10_l11_l12-supply = <&pm8018_s5>; + + /* Buck SMPS */ + pm8018_s1: s1 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1150000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + + pm8018_s2: s2 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1300000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + + pm8018_s3: s3 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + + pm8018_s4: s4 { + regulator-min-microvolt = <2100000>; + regulator-max-microvolt = <2200000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + + pm8018_s5: s5 { + regulator-always-on; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + + /* PMOS LDO */ + pm8018_l2: l2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + + pm8018_l3: l3 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + + pm8018_l4: l4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + bias-pull-down; + }; + + pm8018_l5: l5 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + + pm8018_l6: l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + + pm8018_l7: l7 { + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <1900000>; + bias-pull-down; + }; + + pm8018_l8: l8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + + pm8018_l9: l9 { + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1150000>; + bias-pull-down; + }; + + pm8018_l10: l10 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + bias-pull-down; + }; + + pm8018_l11: l11 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + bias-pull-down; + }; + + pm8018_l12: l12 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + bias-pull-down; + }; + + pm8018_l13: l13 { + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <2950000>; + bias-pull-down; + }; + + pm8018_l14: l14 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + + /* Low Voltage Switch */ + pm8018_lvs1: lvs1 { + bias-pull-down; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index 8c65e0d82559..4d828f810746 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -141,6 +141,23 @@ }; }; + external-bus@1a100000 { + compatible = "qcom,msm8660-ebi2"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0x0 0x1a800000 0x00800000>, + <1 0x0 0x1b000000 0x00800000>, + <2 0x0 0x1b800000 0x00800000>, + <3 0x0 0x1d000000 0x08000000>, + <4 0x0 0x1c800000 0x00800000>, + <5 0x0 0x1c000000 0x00800000>; + reg = <0x1a100000 0x1000>, <0x1a110000 0x1000>; + reg-names = "ebi2", "xmem"; + clocks = <&gcc EBI2_2X_CLK>, <&gcc EBI2_CLK>; + clock-names = "ebi2x", "ebi2"; + status = "disabled"; + }; + qcom,ssbi@500000 { compatible = "qcom,ssbi"; reg = <0x500000 0x1000>; diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts index c0fb4a698c56..382bcc3231a9 100644 --- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts +++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts @@ -224,6 +224,35 @@ status = "ok"; }; + pinctrl@fd510000 { + sdhc1_pin_a: sdhc1-pin-active { + clk { + pins = "sdc1_clk"; + drive-strength = <16>; + bias-disable; + }; + + cmd-data { + pins = "sdc1_cmd", "sdc1_data"; + drive-strength = <10>; + bias-pull-up; + }; + }; + }; + + sdhci@f9824900 { + status = "ok"; + + vmmc-supply = <&pm8941_l20>; + vqmmc-supply = <&pm8941_s3>; + + bus-width = <8>; + non-removable; + + pinctrl-names = "default"; + pinctrl-0 = <&sdhc1_pin_a>; + }; + gpio-keys { compatible = "gpio-keys"; input-name = "gpio-keys";