forked from Minki/linux
[PATCH] Add Myri-10G Ethernet driver
Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Andrew J. Gallatin <gallatin@myri.com> drivers/net/Kconfig | 17 drivers/net/Makefile | 1 drivers/net/myri10ge/Makefile | 5 drivers/net/myri10ge/myri10ge.c | 2851 +++++++++++++++ drivers/net/myri10ge/myri10ge_mcp.h | 205 + drivers/net/myri10ge/myri10ge_mcp_gen_header.h | 58 include/linux/pci_ids.h | 1 7 files changed, 3138 insertions(+) Signed-off-by: Jeff Garzik <jeff@garzik.org>
This commit is contained in:
Brice Goglin
Jeff Garzik
parent
3a720d726a
commit
0da34b6dfe
@ -2327,6 +2327,23 @@ config S2IO_NAPI
|
||||
|
||||
If in doubt, say N.
|
||||
|
||||
config MYRI10GE
|
||||
tristate "Myricom Myri-10G Ethernet support"
|
||||
depends on PCI
|
||||
select FW_LOADER
|
||||
select CRC32
|
||||
---help---
|
||||
This driver supports Myricom Myri-10G Dual Protocol interface in
|
||||
Ethernet mode. If the eeprom on your board is not recent enough,
|
||||
you will need a newer firmware image.
|
||||
You may get this image or more information, at:
|
||||
|
||||
<http://www.myri.com/Myri-10G/>
|
||||
|
||||
To compile this driver as a module, choose M here and read
|
||||
<file:Documentation/networking/net-modules.txt>. The module
|
||||
will be called myri10ge.
|
||||
|
||||
endmenu
|
||||
|
||||
source "drivers/net/tokenring/Kconfig"
|
||||
|
||||
@ -192,6 +192,7 @@ obj-$(CONFIG_R8169) += r8169.o
|
||||
obj-$(CONFIG_AMD8111_ETH) += amd8111e.o
|
||||
obj-$(CONFIG_IBMVETH) += ibmveth.o
|
||||
obj-$(CONFIG_S2IO) += s2io.o
|
||||
obj-$(CONFIG_MYRI10GE) += myri10ge/
|
||||
obj-$(CONFIG_SMC91X) += smc91x.o
|
||||
obj-$(CONFIG_SMC911X) += smc911x.o
|
||||
obj-$(CONFIG_DM9000) += dm9000.o
|
||||
|
||||
5
drivers/net/myri10ge/Makefile
Normal file
5
drivers/net/myri10ge/Makefile
Normal file
@ -0,0 +1,5 @@
|
||||
#
|
||||
# Makefile for the Myricom Myri-10G ethernet driver
|
||||
#
|
||||
|
||||
obj-$(CONFIG_MYRI10GE) += myri10ge.o
|
||||
2851
drivers/net/myri10ge/myri10ge.c
Normal file
2851
drivers/net/myri10ge/myri10ge.c
Normal file
File diff suppressed because it is too large
Load Diff
205
drivers/net/myri10ge/myri10ge_mcp.h
Normal file
205
drivers/net/myri10ge/myri10ge_mcp.h
Normal file
@ -0,0 +1,205 @@
|
||||
#ifndef __MYRI10GE_MCP_H__
|
||||
#define __MYRI10GE_MCP_H__
|
||||
|
||||
#define MXGEFW_VERSION_MAJOR 1
|
||||
#define MXGEFW_VERSION_MINOR 4
|
||||
|
||||
/* 8 Bytes */
|
||||
struct mcp_dma_addr {
|
||||
u32 high;
|
||||
u32 low;
|
||||
};
|
||||
|
||||
/* 4 Bytes */
|
||||
struct mcp_slot {
|
||||
u16 checksum;
|
||||
u16 length;
|
||||
};
|
||||
|
||||
/* 64 Bytes */
|
||||
struct mcp_cmd {
|
||||
u32 cmd;
|
||||
u32 data0; /* will be low portion if data > 32 bits */
|
||||
/* 8 */
|
||||
u32 data1; /* will be high portion if data > 32 bits */
|
||||
u32 data2; /* currently unused.. */
|
||||
/* 16 */
|
||||
struct mcp_dma_addr response_addr;
|
||||
/* 24 */
|
||||
u8 pad[40];
|
||||
};
|
||||
|
||||
/* 8 Bytes */
|
||||
struct mcp_cmd_response {
|
||||
u32 data;
|
||||
u32 result;
|
||||
};
|
||||
|
||||
/*
|
||||
* flags used in mcp_kreq_ether_send_t:
|
||||
*
|
||||
* The SMALL flag is only needed in the first segment. It is raised
|
||||
* for packets that are total less or equal 512 bytes.
|
||||
*
|
||||
* The CKSUM flag must be set in all segments.
|
||||
*
|
||||
* The PADDED flags is set if the packet needs to be padded, and it
|
||||
* must be set for all segments.
|
||||
*
|
||||
* The MXGEFW_FLAGS_ALIGN_ODD must be set if the cumulative
|
||||
* length of all previous segments was odd.
|
||||
*/
|
||||
|
||||
#define MXGEFW_FLAGS_SMALL 0x1
|
||||
#define MXGEFW_FLAGS_TSO_HDR 0x1
|
||||
#define MXGEFW_FLAGS_FIRST 0x2
|
||||
#define MXGEFW_FLAGS_ALIGN_ODD 0x4
|
||||
#define MXGEFW_FLAGS_CKSUM 0x8
|
||||
#define MXGEFW_FLAGS_TSO_LAST 0x8
|
||||
#define MXGEFW_FLAGS_NO_TSO 0x10
|
||||
#define MXGEFW_FLAGS_TSO_CHOP 0x10
|
||||
#define MXGEFW_FLAGS_TSO_PLD 0x20
|
||||
|
||||
#define MXGEFW_SEND_SMALL_SIZE 1520
|
||||
#define MXGEFW_MAX_MTU 9400
|
||||
|
||||
union mcp_pso_or_cumlen {
|
||||
u16 pseudo_hdr_offset;
|
||||
u16 cum_len;
|
||||
};
|
||||
|
||||
#define MXGEFW_MAX_SEND_DESC 12
|
||||
#define MXGEFW_PAD 2
|
||||
|
||||
/* 16 Bytes */
|
||||
struct mcp_kreq_ether_send {
|
||||
u32 addr_high;
|
||||
u32 addr_low;
|
||||
u16 pseudo_hdr_offset;
|
||||
u16 length;
|
||||
u8 pad;
|
||||
u8 rdma_count;
|
||||
u8 cksum_offset; /* where to start computing cksum */
|
||||
u8 flags; /* as defined above */
|
||||
};
|
||||
|
||||
/* 8 Bytes */
|
||||
struct mcp_kreq_ether_recv {
|
||||
u32 addr_high;
|
||||
u32 addr_low;
|
||||
};
|
||||
|
||||
/* Commands */
|
||||
|
||||
#define MXGEFW_CMD_OFFSET 0xf80000
|
||||
|
||||
enum myri10ge_mcp_cmd_type {
|
||||
MXGEFW_CMD_NONE = 0,
|
||||
/* Reset the mcp, it is left in a safe state, waiting
|
||||
* for the driver to set all its parameters */
|
||||
MXGEFW_CMD_RESET,
|
||||
|
||||
/* get the version number of the current firmware..
|
||||
* (may be available in the eeprom strings..? */
|
||||
MXGEFW_GET_MCP_VERSION,
|
||||
|
||||
/* Parameters which must be set by the driver before it can
|
||||
* issue MXGEFW_CMD_ETHERNET_UP. They persist until the next
|
||||
* MXGEFW_CMD_RESET is issued */
|
||||
|
||||
MXGEFW_CMD_SET_INTRQ_DMA,
|
||||
MXGEFW_CMD_SET_BIG_BUFFER_SIZE, /* in bytes, power of 2 */
|
||||
MXGEFW_CMD_SET_SMALL_BUFFER_SIZE, /* in bytes */
|
||||
|
||||
/* Parameters which refer to lanai SRAM addresses where the
|
||||
* driver must issue PIO writes for various things */
|
||||
|
||||
MXGEFW_CMD_GET_SEND_OFFSET,
|
||||
MXGEFW_CMD_GET_SMALL_RX_OFFSET,
|
||||
MXGEFW_CMD_GET_BIG_RX_OFFSET,
|
||||
MXGEFW_CMD_GET_IRQ_ACK_OFFSET,
|
||||
MXGEFW_CMD_GET_IRQ_DEASSERT_OFFSET,
|
||||
|
||||
/* Parameters which refer to rings stored on the MCP,
|
||||
* and whose size is controlled by the mcp */
|
||||
|
||||
MXGEFW_CMD_GET_SEND_RING_SIZE, /* in bytes */
|
||||
MXGEFW_CMD_GET_RX_RING_SIZE, /* in bytes */
|
||||
|
||||
/* Parameters which refer to rings stored in the host,
|
||||
* and whose size is controlled by the host. Note that
|
||||
* all must be physically contiguous and must contain
|
||||
* a power of 2 number of entries. */
|
||||
|
||||
MXGEFW_CMD_SET_INTRQ_SIZE, /* in bytes */
|
||||
|
||||
/* command to bring ethernet interface up. Above parameters
|
||||
* (plus mtu & mac address) must have been exchanged prior
|
||||
* to issuing this command */
|
||||
MXGEFW_CMD_ETHERNET_UP,
|
||||
|
||||
/* command to bring ethernet interface down. No further sends
|
||||
* or receives may be processed until an MXGEFW_CMD_ETHERNET_UP
|
||||
* is issued, and all interrupt queues must be flushed prior
|
||||
* to ack'ing this command */
|
||||
|
||||
MXGEFW_CMD_ETHERNET_DOWN,
|
||||
|
||||
/* commands the driver may issue live, without resetting
|
||||
* the nic. Note that increasing the mtu "live" should
|
||||
* only be done if the driver has already supplied buffers
|
||||
* sufficiently large to handle the new mtu. Decreasing
|
||||
* the mtu live is safe */
|
||||
|
||||
MXGEFW_CMD_SET_MTU,
|
||||
MXGEFW_CMD_GET_INTR_COAL_DELAY_OFFSET, /* in microseconds */
|
||||
MXGEFW_CMD_SET_STATS_INTERVAL, /* in microseconds */
|
||||
MXGEFW_CMD_SET_STATS_DMA,
|
||||
|
||||
MXGEFW_ENABLE_PROMISC,
|
||||
MXGEFW_DISABLE_PROMISC,
|
||||
MXGEFW_SET_MAC_ADDRESS,
|
||||
|
||||
MXGEFW_ENABLE_FLOW_CONTROL,
|
||||
MXGEFW_DISABLE_FLOW_CONTROL,
|
||||
|
||||
/* do a DMA test
|
||||
* data0,data1 = DMA address
|
||||
* data2 = RDMA length (MSH), WDMA length (LSH)
|
||||
* command return data = repetitions (MSH), 0.5-ms ticks (LSH)
|
||||
*/
|
||||
MXGEFW_DMA_TEST
|
||||
};
|
||||
|
||||
enum myri10ge_mcp_cmd_status {
|
||||
MXGEFW_CMD_OK = 0,
|
||||
MXGEFW_CMD_UNKNOWN,
|
||||
MXGEFW_CMD_ERROR_RANGE,
|
||||
MXGEFW_CMD_ERROR_BUSY,
|
||||
MXGEFW_CMD_ERROR_EMPTY,
|
||||
MXGEFW_CMD_ERROR_CLOSED,
|
||||
MXGEFW_CMD_ERROR_HASH_ERROR,
|
||||
MXGEFW_CMD_ERROR_BAD_PORT,
|
||||
MXGEFW_CMD_ERROR_RESOURCES
|
||||
};
|
||||
|
||||
/* 40 Bytes */
|
||||
struct mcp_irq_data {
|
||||
u32 send_done_count;
|
||||
|
||||
u32 link_up;
|
||||
u32 dropped_link_overflow;
|
||||
u32 dropped_link_error_or_filtered;
|
||||
u32 dropped_runt;
|
||||
u32 dropped_overrun;
|
||||
u32 dropped_no_small_buffer;
|
||||
u32 dropped_no_big_buffer;
|
||||
u32 rdma_tags_available;
|
||||
|
||||
u8 tx_stopped;
|
||||
u8 link_down;
|
||||
u8 stats_updated;
|
||||
u8 valid;
|
||||
};
|
||||
|
||||
#endif /* __MYRI10GE_MCP_H__ */
|
||||
58
drivers/net/myri10ge/myri10ge_mcp_gen_header.h
Normal file
58
drivers/net/myri10ge/myri10ge_mcp_gen_header.h
Normal file
@ -0,0 +1,58 @@
|
||||
#ifndef __MYRI10GE_MCP_GEN_HEADER_H__
|
||||
#define __MYRI10GE_MCP_GEN_HEADER_H__
|
||||
|
||||
/* this file define a standard header used as a first entry point to
|
||||
* exchange information between firmware/driver and driver. The
|
||||
* header structure can be anywhere in the mcp. It will usually be in
|
||||
* the .data section, because some fields needs to be initialized at
|
||||
* compile time.
|
||||
* The 32bit word at offset MX_HEADER_PTR_OFFSET in the mcp must
|
||||
* contains the location of the header.
|
||||
*
|
||||
* Typically a MCP will start with the following:
|
||||
* .text
|
||||
* .space 52 ! to help catch MEMORY_INT errors
|
||||
* bt start ! jump to real code
|
||||
* nop
|
||||
* .long _gen_mcp_header
|
||||
*
|
||||
* The source will have a definition like:
|
||||
*
|
||||
* mcp_gen_header_t gen_mcp_header = {
|
||||
* .header_length = sizeof(mcp_gen_header_t),
|
||||
* .mcp_type = MCP_TYPE_XXX,
|
||||
* .version = "something $Id: mcp_gen_header.h,v 1.2 2006/05/13 10:04:35 bgoglin Exp $",
|
||||
* .mcp_globals = (unsigned)&Globals
|
||||
* };
|
||||
*/
|
||||
|
||||
#define MCP_HEADER_PTR_OFFSET 0x3c
|
||||
|
||||
#define MCP_TYPE_MX 0x4d582020 /* "MX " */
|
||||
#define MCP_TYPE_PCIE 0x70636965 /* "PCIE" pcie-only MCP */
|
||||
#define MCP_TYPE_ETH 0x45544820 /* "ETH " */
|
||||
#define MCP_TYPE_MCP0 0x4d435030 /* "MCP0" */
|
||||
|
||||
struct mcp_gen_header {
|
||||
/* the first 4 fields are filled at compile time */
|
||||
unsigned header_length;
|
||||
unsigned mcp_type;
|
||||
char version[128];
|
||||
unsigned mcp_globals; /* pointer to mcp-type specific structure */
|
||||
|
||||
/* filled by the MCP at run-time */
|
||||
unsigned sram_size;
|
||||
unsigned string_specs; /* either the original STRING_SPECS or a superset */
|
||||
unsigned string_specs_len;
|
||||
|
||||
/* Fields above this comment are guaranteed to be present.
|
||||
*
|
||||
* Fields below this comment are extensions added in later versions
|
||||
* of this struct, drivers should compare the header_length against
|
||||
* offsetof(field) to check wether a given MCP implements them.
|
||||
*
|
||||
* Never remove any field. Keep everything naturally align.
|
||||
*/
|
||||
};
|
||||
|
||||
#endif /* __MYRI10GE_MCP_GEN_HEADER_H__ */
|
||||
@ -1827,6 +1827,7 @@
|
||||
|
||||
#define PCI_VENDOR_ID_SAMSUNG 0x144d
|
||||
|
||||
#define PCI_VENDOR_ID_MYRICOM 0x14c1
|
||||
|
||||
#define PCI_VENDOR_ID_TITAN 0x14D2
|
||||
#define PCI_DEVICE_ID_TITAN_010L 0x8001
|
||||
|
||||
Loading…
Reference in New Issue
Block a user