linux/fs/iomap.c

1509 lines
37 KiB
C
Raw Normal View History

/*
* Copyright (C) 2010 Red Hat, Inc.
* Copyright (c) 2016 Christoph Hellwig.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*/
#include <linux/module.h>
#include <linux/compiler.h>
#include <linux/fs.h>
#include <linux/iomap.h>
#include <linux/uaccess.h>
#include <linux/gfp.h>
#include <linux/mm.h>
#include <linux/swap.h>
#include <linux/pagemap.h>
#include <linux/pagevec.h>
#include <linux/file.h>
#include <linux/uio.h>
#include <linux/backing-dev.h>
#include <linux/buffer_head.h>
#include <linux/task_io_accounting_ops.h>
#include <linux/dax.h>
#include <linux/sched/signal.h>
#include <linux/swap.h>
#include "internal.h"
/*
* Execute a iomap write on a segment of the mapping that spans a
* contiguous range of pages that have identical block mapping state.
*
* This avoids the need to map pages individually, do individual allocations
* for each page and most importantly avoid the need for filesystem specific
* locking per page. Instead, all the operations are amortised over the entire
* range of pages. It is assumed that the filesystems will lock whatever
* resources they require in the iomap_begin call, and release them in the
* iomap_end call.
*/
loff_t
iomap_apply(struct inode *inode, loff_t pos, loff_t length, unsigned flags,
const struct iomap_ops *ops, void *data, iomap_actor_t actor)
{
struct iomap iomap = { 0 };
loff_t written = 0, ret;
/*
* Need to map a range from start position for length bytes. This can
* span multiple pages - it is only guaranteed to return a range of a
* single type of pages (e.g. all into a hole, all mapped or all
* unwritten). Failure at this point has nothing to undo.
*
* If allocation is required for this range, reserve the space now so
* that the allocation is guaranteed to succeed later on. Once we copy
* the data into the page cache pages, then we cannot fail otherwise we
* expose transient stale data. If the reserve fails, we can safely
* back out at this point as there is nothing to undo.
*/
ret = ops->iomap_begin(inode, pos, length, flags, &iomap);
if (ret)
return ret;
if (WARN_ON(iomap.offset > pos))
return -EIO;
if (WARN_ON(iomap.length == 0))
return -EIO;
/*
* Cut down the length to the one actually provided by the filesystem,
* as it might not be able to give us the whole size that we requested.
*/
if (iomap.offset + iomap.length < pos + length)
length = iomap.offset + iomap.length - pos;
/*
* Now that we have guaranteed that the space allocation will succeed.
* we can do the copy-in page by page without having to worry about
* failures exposing transient data.
*/
written = actor(inode, pos, length, data, &iomap);
/*
* Now the data has been copied, commit the range we've copied. This
* should not fail unless the filesystem has had a fatal error.
*/
if (ops->iomap_end) {
ret = ops->iomap_end(inode, pos, length,
written > 0 ? written : 0,
flags, &iomap);
}
return written ? written : ret;
}
static sector_t
iomap_sector(struct iomap *iomap, loff_t pos)
{
return (iomap->addr + pos - iomap->offset) >> SECTOR_SHIFT;
}
static void
iomap_read_inline_data(struct inode *inode, struct page *page,
struct iomap *iomap)
{
size_t size = i_size_read(inode);
void *addr;
if (PageUptodate(page))
return;
BUG_ON(page->index);
BUG_ON(size > PAGE_SIZE - offset_in_page(iomap->inline_data));
addr = kmap_atomic(page);
memcpy(addr, iomap->inline_data, size);
memset(addr + size, 0, PAGE_SIZE - size);
kunmap_atomic(addr);
SetPageUptodate(page);
}
static void
iomap_write_failed(struct inode *inode, loff_t pos, unsigned len)
{
loff_t i_size = i_size_read(inode);
/*
* Only truncate newly allocated pages beyoned EOF, even if the
* write started inside the existing inode size.
*/
if (pos + len > i_size)
truncate_pagecache_range(inode, max(pos, i_size), pos + len);
}
static int
iomap_write_begin(struct inode *inode, loff_t pos, unsigned len, unsigned flags,
struct page **pagep, struct iomap *iomap)
{
pgoff_t index = pos >> PAGE_SHIFT;
struct page *page;
int status = 0;
BUG_ON(pos + len > iomap->offset + iomap->length);
fs: break out of iomap_file_buffered_write on fatal signals Tetsuo has noticed that an OOM stress test which performs large write requests can cause the full memory reserves depletion. He has tracked this down to the following path __alloc_pages_nodemask+0x436/0x4d0 alloc_pages_current+0x97/0x1b0 __page_cache_alloc+0x15d/0x1a0 mm/filemap.c:728 pagecache_get_page+0x5a/0x2b0 mm/filemap.c:1331 grab_cache_page_write_begin+0x23/0x40 mm/filemap.c:2773 iomap_write_begin+0x50/0xd0 fs/iomap.c:118 iomap_write_actor+0xb5/0x1a0 fs/iomap.c:190 ? iomap_write_end+0x80/0x80 fs/iomap.c:150 iomap_apply+0xb3/0x130 fs/iomap.c:79 iomap_file_buffered_write+0x68/0xa0 fs/iomap.c:243 ? iomap_write_end+0x80/0x80 xfs_file_buffered_aio_write+0x132/0x390 [xfs] ? remove_wait_queue+0x59/0x60 xfs_file_write_iter+0x90/0x130 [xfs] __vfs_write+0xe5/0x140 vfs_write+0xc7/0x1f0 ? syscall_trace_enter+0x1d0/0x380 SyS_write+0x58/0xc0 do_syscall_64+0x6c/0x200 entry_SYSCALL64_slow_path+0x25/0x25 the oom victim has access to all memory reserves to make a forward progress to exit easier. But iomap_file_buffered_write and other callers of iomap_apply loop to complete the full request. We need to check for fatal signals and back off with a short write instead. As the iomap_apply delegates all the work down to the actor we have to hook into those. All callers that work with the page cache are calling iomap_write_begin so we will check for signals there. dax_iomap_actor has to handle the situation explicitly because it copies data to the userspace directly. Other callers like iomap_page_mkwrite work on a single page or iomap_fiemap_actor do not allocate memory based on the given len. Fixes: 68a9f5e7007c ("xfs: implement iomap based buffered write path") Link: http://lkml.kernel.org/r/20170201092706.9966-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-02-03 21:13:26 +00:00
if (fatal_signal_pending(current))
return -EINTR;
page = grab_cache_page_write_begin(inode->i_mapping, index, flags);
if (!page)
return -ENOMEM;
if (iomap->type == IOMAP_INLINE)
iomap_read_inline_data(inode, page, iomap);
else
status = __block_write_begin_int(page, pos, len, NULL, iomap);
if (unlikely(status)) {
unlock_page(page);
put_page(page);
page = NULL;
iomap_write_failed(inode, pos, len);
}
*pagep = page;
return status;
}
static int
iomap_write_end_inline(struct inode *inode, struct page *page,
struct iomap *iomap, loff_t pos, unsigned copied)
{
void *addr;
WARN_ON_ONCE(!PageUptodate(page));
BUG_ON(pos + copied > PAGE_SIZE - offset_in_page(iomap->inline_data));
addr = kmap_atomic(page);
memcpy(iomap->inline_data + pos, addr + pos, copied);
kunmap_atomic(addr);
mark_inode_dirty(inode);
__generic_write_end(inode, pos, copied, page);
return copied;
}
static int
iomap_write_end(struct inode *inode, loff_t pos, unsigned len,
unsigned copied, struct page *page, struct iomap *iomap)
{
int ret;
if (iomap->type == IOMAP_INLINE) {
ret = iomap_write_end_inline(inode, page, iomap, pos, copied);
} else {
ret = generic_write_end(NULL, inode->i_mapping, pos, len,
copied, page, NULL);
}
if (iomap->page_done)
iomap->page_done(inode, pos, copied, page, iomap);
if (ret < len)
iomap_write_failed(inode, pos, len);
return ret;
}
static loff_t
iomap_write_actor(struct inode *inode, loff_t pos, loff_t length, void *data,
struct iomap *iomap)
{
struct iov_iter *i = data;
long status = 0;
ssize_t written = 0;
unsigned int flags = AOP_FLAG_NOFS;
do {
struct page *page;
unsigned long offset; /* Offset into pagecache page */
unsigned long bytes; /* Bytes to write to page */
size_t copied; /* Bytes copied from user */
offset = (pos & (PAGE_SIZE - 1));
bytes = min_t(unsigned long, PAGE_SIZE - offset,
iov_iter_count(i));
again:
if (bytes > length)
bytes = length;
/*
* Bring in the user page that we will copy from _first_.
* Otherwise there's a nasty deadlock on copying from the
* same page as we're writing to, without it being marked
* up-to-date.
*
* Not only is this an optimisation, but it is also required
* to check that the address is actually valid, when atomic
* usercopies are used, below.
*/
if (unlikely(iov_iter_fault_in_readable(i, bytes))) {
status = -EFAULT;
break;
}
status = iomap_write_begin(inode, pos, bytes, flags, &page,
iomap);
if (unlikely(status))
break;
if (mapping_writably_mapped(inode->i_mapping))
flush_dcache_page(page);
copied = iov_iter_copy_from_user_atomic(page, i, offset, bytes);
flush_dcache_page(page);
status = iomap_write_end(inode, pos, bytes, copied, page,
iomap);
if (unlikely(status < 0))
break;
copied = status;
cond_resched();
iov_iter_advance(i, copied);
if (unlikely(copied == 0)) {
/*
* If we were unable to copy any data at all, we must
* fall back to a single segment length write.
*
* If we didn't fallback here, we could livelock
* because not all segments in the iov can be copied at
* once without a pagefault.
*/
bytes = min_t(unsigned long, PAGE_SIZE - offset,
iov_iter_single_seg_count(i));
goto again;
}
pos += copied;
written += copied;
length -= copied;
balance_dirty_pages_ratelimited(inode->i_mapping);
} while (iov_iter_count(i) && length);
return written ? written : status;
}
ssize_t
iomap_file_buffered_write(struct kiocb *iocb, struct iov_iter *iter,
const struct iomap_ops *ops)
{
struct inode *inode = iocb->ki_filp->f_mapping->host;
loff_t pos = iocb->ki_pos, ret = 0, written = 0;
while (iov_iter_count(iter)) {
ret = iomap_apply(inode, pos, iov_iter_count(iter),
IOMAP_WRITE, ops, iter, iomap_write_actor);
if (ret <= 0)
break;
pos += ret;
written += ret;
}
return written ? written : ret;
}
EXPORT_SYMBOL_GPL(iomap_file_buffered_write);
static struct page *
__iomap_read_page(struct inode *inode, loff_t offset)
{
struct address_space *mapping = inode->i_mapping;
struct page *page;
page = read_mapping_page(mapping, offset >> PAGE_SHIFT, NULL);
if (IS_ERR(page))
return page;
if (!PageUptodate(page)) {
put_page(page);
return ERR_PTR(-EIO);
}
return page;
}
static loff_t
iomap_dirty_actor(struct inode *inode, loff_t pos, loff_t length, void *data,
struct iomap *iomap)
{
long status = 0;
ssize_t written = 0;
do {
struct page *page, *rpage;
unsigned long offset; /* Offset into pagecache page */
unsigned long bytes; /* Bytes to write to page */
offset = (pos & (PAGE_SIZE - 1));
bytes = min_t(loff_t, PAGE_SIZE - offset, length);
rpage = __iomap_read_page(inode, pos);
if (IS_ERR(rpage))
return PTR_ERR(rpage);
status = iomap_write_begin(inode, pos, bytes,
AOP_FLAG_NOFS, &page, iomap);
put_page(rpage);
if (unlikely(status))
return status;
WARN_ON_ONCE(!PageUptodate(page));
status = iomap_write_end(inode, pos, bytes, bytes, page, iomap);
if (unlikely(status <= 0)) {
if (WARN_ON_ONCE(status == 0))
return -EIO;
return status;
}
cond_resched();
pos += status;
written += status;
length -= status;
balance_dirty_pages_ratelimited(inode->i_mapping);
} while (length);
return written;
}
int
iomap_file_dirty(struct inode *inode, loff_t pos, loff_t len,
const struct iomap_ops *ops)
{
loff_t ret;
while (len) {
ret = iomap_apply(inode, pos, len, IOMAP_WRITE, ops, NULL,
iomap_dirty_actor);
if (ret <= 0)
return ret;
pos += ret;
len -= ret;
}
return 0;
}
EXPORT_SYMBOL_GPL(iomap_file_dirty);
static int iomap_zero(struct inode *inode, loff_t pos, unsigned offset,
unsigned bytes, struct iomap *iomap)
{
struct page *page;
int status;
status = iomap_write_begin(inode, pos, bytes, AOP_FLAG_NOFS, &page,
iomap);
if (status)
return status;
zero_user(page, offset, bytes);
mark_page_accessed(page);
return iomap_write_end(inode, pos, bytes, bytes, page, iomap);
}
static int iomap_dax_zero(loff_t pos, unsigned offset, unsigned bytes,
struct iomap *iomap)
{
return __dax_zero_page_range(iomap->bdev, iomap->dax_dev,
iomap_sector(iomap, pos & PAGE_MASK), offset, bytes);
}
static loff_t
iomap_zero_range_actor(struct inode *inode, loff_t pos, loff_t count,
void *data, struct iomap *iomap)
{
bool *did_zero = data;
loff_t written = 0;
int status;
/* already zeroed? we're done. */
if (iomap->type == IOMAP_HOLE || iomap->type == IOMAP_UNWRITTEN)
return count;
do {
unsigned offset, bytes;
offset = pos & (PAGE_SIZE - 1); /* Within page */
bytes = min_t(loff_t, PAGE_SIZE - offset, count);
if (IS_DAX(inode))
status = iomap_dax_zero(pos, offset, bytes, iomap);
else
status = iomap_zero(inode, pos, offset, bytes, iomap);
if (status < 0)
return status;
pos += bytes;
count -= bytes;
written += bytes;
if (did_zero)
*did_zero = true;
} while (count > 0);
return written;
}
int
iomap_zero_range(struct inode *inode, loff_t pos, loff_t len, bool *did_zero,
const struct iomap_ops *ops)
{
loff_t ret;
while (len > 0) {
ret = iomap_apply(inode, pos, len, IOMAP_ZERO,
ops, did_zero, iomap_zero_range_actor);
if (ret <= 0)
return ret;
pos += ret;
len -= ret;
}
return 0;
}
EXPORT_SYMBOL_GPL(iomap_zero_range);
int
iomap_truncate_page(struct inode *inode, loff_t pos, bool *did_zero,
const struct iomap_ops *ops)
{
unsigned int blocksize = i_blocksize(inode);
unsigned int off = pos & (blocksize - 1);
/* Block boundary? Nothing to do */
if (!off)
return 0;
return iomap_zero_range(inode, pos, blocksize - off, did_zero, ops);
}
EXPORT_SYMBOL_GPL(iomap_truncate_page);
static loff_t
iomap_page_mkwrite_actor(struct inode *inode, loff_t pos, loff_t length,
void *data, struct iomap *iomap)
{
struct page *page = data;
int ret;
ret = __block_write_begin_int(page, pos, length, NULL, iomap);
if (ret)
return ret;
block_commit_write(page, 0, length);
return length;
}
int iomap_page_mkwrite(struct vm_fault *vmf, const struct iomap_ops *ops)
{
struct page *page = vmf->page;
struct inode *inode = file_inode(vmf->vma->vm_file);
unsigned long length;
loff_t offset, size;
ssize_t ret;
lock_page(page);
size = i_size_read(inode);
if ((page->mapping != inode->i_mapping) ||
(page_offset(page) > size)) {
/* We overload EFAULT to mean page got truncated */
ret = -EFAULT;
goto out_unlock;
}
/* page is wholly or partially inside EOF */
if (((page->index + 1) << PAGE_SHIFT) > size)
length = size & ~PAGE_MASK;
else
length = PAGE_SIZE;
offset = page_offset(page);
while (length > 0) {
ret = iomap_apply(inode, offset, length,
IOMAP_WRITE | IOMAP_FAULT, ops, page,
iomap_page_mkwrite_actor);
if (unlikely(ret <= 0))
goto out_unlock;
offset += ret;
length -= ret;
}
set_page_dirty(page);
wait_for_stable_page(page);
return VM_FAULT_LOCKED;
out_unlock:
unlock_page(page);
return block_page_mkwrite_return(ret);
}
EXPORT_SYMBOL_GPL(iomap_page_mkwrite);
struct fiemap_ctx {
struct fiemap_extent_info *fi;
struct iomap prev;
};
static int iomap_to_fiemap(struct fiemap_extent_info *fi,
struct iomap *iomap, u32 flags)
{
switch (iomap->type) {
case IOMAP_HOLE:
/* skip holes */
return 0;
case IOMAP_DELALLOC:
flags |= FIEMAP_EXTENT_DELALLOC | FIEMAP_EXTENT_UNKNOWN;
break;
case IOMAP_MAPPED:
break;
case IOMAP_UNWRITTEN:
flags |= FIEMAP_EXTENT_UNWRITTEN;
break;
case IOMAP_INLINE:
flags |= FIEMAP_EXTENT_DATA_INLINE;
break;
}
if (iomap->flags & IOMAP_F_MERGED)
flags |= FIEMAP_EXTENT_MERGED;
if (iomap->flags & IOMAP_F_SHARED)
flags |= FIEMAP_EXTENT_SHARED;
return fiemap_fill_next_extent(fi, iomap->offset,
iomap->addr != IOMAP_NULL_ADDR ? iomap->addr : 0,
iomap->length, flags);
}
static loff_t
iomap_fiemap_actor(struct inode *inode, loff_t pos, loff_t length, void *data,
struct iomap *iomap)
{
struct fiemap_ctx *ctx = data;
loff_t ret = length;
if (iomap->type == IOMAP_HOLE)
return length;
ret = iomap_to_fiemap(ctx->fi, &ctx->prev, 0);
ctx->prev = *iomap;
switch (ret) {
case 0: /* success */
return length;
case 1: /* extent array full */
return 0;
default:
return ret;
}
}
int iomap_fiemap(struct inode *inode, struct fiemap_extent_info *fi,
loff_t start, loff_t len, const struct iomap_ops *ops)
{
struct fiemap_ctx ctx;
loff_t ret;
memset(&ctx, 0, sizeof(ctx));
ctx.fi = fi;
ctx.prev.type = IOMAP_HOLE;
ret = fiemap_check_flags(fi, FIEMAP_FLAG_SYNC);
if (ret)
return ret;
if (fi->fi_flags & FIEMAP_FLAG_SYNC) {
ret = filemap_write_and_wait(inode->i_mapping);
if (ret)
return ret;
}
while (len > 0) {
ret = iomap_apply(inode, start, len, IOMAP_REPORT, ops, &ctx,
iomap_fiemap_actor);
/* inode with no (attribute) mapping will give ENOENT */
if (ret == -ENOENT)
break;
if (ret < 0)
return ret;
if (ret == 0)
break;
start += ret;
len -= ret;
}
if (ctx.prev.type != IOMAP_HOLE) {
ret = iomap_to_fiemap(fi, &ctx.prev, FIEMAP_EXTENT_LAST);
if (ret < 0)
return ret;
}
return 0;
}
EXPORT_SYMBOL_GPL(iomap_fiemap);
/*
* Seek for SEEK_DATA / SEEK_HOLE within @page, starting at @lastoff.
* Returns true if found and updates @lastoff to the offset in file.
*/
static bool
page_seek_hole_data(struct inode *inode, struct page *page, loff_t *lastoff,
int whence)
{
const struct address_space_operations *ops = inode->i_mapping->a_ops;
unsigned int bsize = i_blocksize(inode), off;
bool seek_data = whence == SEEK_DATA;
loff_t poff = page_offset(page);
if (WARN_ON_ONCE(*lastoff >= poff + PAGE_SIZE))
return false;
if (*lastoff < poff) {
/*
* Last offset smaller than the start of the page means we found
* a hole:
*/
if (whence == SEEK_HOLE)
return true;
*lastoff = poff;
}
/*
* Just check the page unless we can and should check block ranges:
*/
if (bsize == PAGE_SIZE || !ops->is_partially_uptodate)
return PageUptodate(page) == seek_data;
lock_page(page);
if (unlikely(page->mapping != inode->i_mapping))
goto out_unlock_not_found;
for (off = 0; off < PAGE_SIZE; off += bsize) {
if ((*lastoff & ~PAGE_MASK) >= off + bsize)
continue;
if (ops->is_partially_uptodate(page, off, bsize) == seek_data) {
unlock_page(page);
return true;
}
*lastoff = poff + off + bsize;
}
out_unlock_not_found:
unlock_page(page);
return false;
}
/*
* Seek for SEEK_DATA / SEEK_HOLE in the page cache.
*
* Within unwritten extents, the page cache determines which parts are holes
* and which are data: uptodate buffer heads count as data; everything else
* counts as a hole.
*
* Returns the resulting offset on successs, and -ENOENT otherwise.
*/
static loff_t
page_cache_seek_hole_data(struct inode *inode, loff_t offset, loff_t length,
int whence)
{
pgoff_t index = offset >> PAGE_SHIFT;
pgoff_t end = DIV_ROUND_UP(offset + length, PAGE_SIZE);
loff_t lastoff = offset;
struct pagevec pvec;
if (length <= 0)
return -ENOENT;
pagevec_init(&pvec);
do {
unsigned nr_pages, i;
nr_pages = pagevec_lookup_range(&pvec, inode->i_mapping, &index,
end - 1);
if (nr_pages == 0)
break;
for (i = 0; i < nr_pages; i++) {
struct page *page = pvec.pages[i];
if (page_seek_hole_data(inode, page, &lastoff, whence))
goto check_range;
lastoff = page_offset(page) + PAGE_SIZE;
}
pagevec_release(&pvec);
} while (index < end);
/* When no page at lastoff and we are not done, we found a hole. */
if (whence != SEEK_HOLE)
goto not_found;
check_range:
if (lastoff < offset + length)
goto out;
not_found:
lastoff = -ENOENT;
out:
pagevec_release(&pvec);
return lastoff;
}
static loff_t
iomap_seek_hole_actor(struct inode *inode, loff_t offset, loff_t length,
void *data, struct iomap *iomap)
{
switch (iomap->type) {
case IOMAP_UNWRITTEN:
offset = page_cache_seek_hole_data(inode, offset, length,
SEEK_HOLE);
if (offset < 0)
return length;
/* fall through */
case IOMAP_HOLE:
*(loff_t *)data = offset;
return 0;
default:
return length;
}
}
loff_t
iomap_seek_hole(struct inode *inode, loff_t offset, const struct iomap_ops *ops)
{
loff_t size = i_size_read(inode);
loff_t length = size - offset;
loff_t ret;
/* Nothing to be found before or beyond the end of the file. */
if (offset < 0 || offset >= size)
return -ENXIO;
while (length > 0) {
ret = iomap_apply(inode, offset, length, IOMAP_REPORT, ops,
&offset, iomap_seek_hole_actor);
if (ret < 0)
return ret;
if (ret == 0)
break;
offset += ret;
length -= ret;
}
return offset;
}
EXPORT_SYMBOL_GPL(iomap_seek_hole);
static loff_t
iomap_seek_data_actor(struct inode *inode, loff_t offset, loff_t length,
void *data, struct iomap *iomap)
{
switch (iomap->type) {
case IOMAP_HOLE:
return length;
case IOMAP_UNWRITTEN:
offset = page_cache_seek_hole_data(inode, offset, length,
SEEK_DATA);
if (offset < 0)
return length;
/*FALLTHRU*/
default:
*(loff_t *)data = offset;
return 0;
}
}
loff_t
iomap_seek_data(struct inode *inode, loff_t offset, const struct iomap_ops *ops)
{
loff_t size = i_size_read(inode);
loff_t length = size - offset;
loff_t ret;
/* Nothing to be found before or beyond the end of the file. */
if (offset < 0 || offset >= size)
return -ENXIO;
while (length > 0) {
ret = iomap_apply(inode, offset, length, IOMAP_REPORT, ops,
&offset, iomap_seek_data_actor);
if (ret < 0)
return ret;
if (ret == 0)
break;
offset += ret;
length -= ret;
}
if (length <= 0)
return -ENXIO;
return offset;
}
EXPORT_SYMBOL_GPL(iomap_seek_data);
/*
* Private flags for iomap_dio, must not overlap with the public ones in
* iomap.h:
*/
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
#define IOMAP_DIO_WRITE_FUA (1 << 28)
#define IOMAP_DIO_NEED_SYNC (1 << 29)
#define IOMAP_DIO_WRITE (1 << 30)
#define IOMAP_DIO_DIRTY (1 << 31)
struct iomap_dio {
struct kiocb *iocb;
iomap_dio_end_io_t *end_io;
loff_t i_size;
loff_t size;
atomic_t ref;
unsigned flags;
int error;
bool wait_for_completion;
union {
/* used during submission and for synchronous completion: */
struct {
struct iov_iter *iter;
struct task_struct *waiter;
struct request_queue *last_queue;
blk_qc_t cookie;
} submit;
/* used for aio completion: */
struct {
struct work_struct work;
} aio;
};
};
static ssize_t iomap_dio_complete(struct iomap_dio *dio)
{
struct kiocb *iocb = dio->iocb;
struct inode *inode = file_inode(iocb->ki_filp);
fs: invalidate page cache after end_io() in dio completion Commit 332391a9935d ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO") moved page cache invalidation from iomap_dio_rw() to iomap_dio_complete() for iomap based direct write path, but before the dio->end_io() call, and it re-introdued the bug fixed by commit c771c14baa33 ("iomap: invalidate page caches should be after iomap_dio_complete() in direct write"). I found this because fstests generic/418 started failing on XFS with v4.14-rc3 kernel, which is the regression test for this specific bug. So similarly, fix it by moving dio->end_io() (which does the unwritten extent conversion) before page cache invalidation, to make sure next buffer read reads the final real allocations not unwritten extents. I also add some comments about why should end_io() go first in case we get it wrong again in the future. Note that, there's no such problem in the non-iomap based direct write path, because we didn't remove the page cache invalidation after the ->direct_IO() in generic_file_direct_write() call, but I decided to fix dio_complete() too so we don't leave a landmine there, also be consistent with iomap_dio_complete(). Fixes: 332391a9935d ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO") Signed-off-by: Eryu Guan <eguan@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Lukas Czerner <lczerner@redhat.com>
2017-10-13 16:47:46 +00:00
loff_t offset = iocb->ki_pos;
ssize_t ret;
if (dio->end_io) {
ret = dio->end_io(iocb,
dio->error ? dio->error : dio->size,
dio->flags);
} else {
ret = dio->error;
}
if (likely(!ret)) {
ret = dio->size;
/* check for short read */
fs: invalidate page cache after end_io() in dio completion Commit 332391a9935d ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO") moved page cache invalidation from iomap_dio_rw() to iomap_dio_complete() for iomap based direct write path, but before the dio->end_io() call, and it re-introdued the bug fixed by commit c771c14baa33 ("iomap: invalidate page caches should be after iomap_dio_complete() in direct write"). I found this because fstests generic/418 started failing on XFS with v4.14-rc3 kernel, which is the regression test for this specific bug. So similarly, fix it by moving dio->end_io() (which does the unwritten extent conversion) before page cache invalidation, to make sure next buffer read reads the final real allocations not unwritten extents. I also add some comments about why should end_io() go first in case we get it wrong again in the future. Note that, there's no such problem in the non-iomap based direct write path, because we didn't remove the page cache invalidation after the ->direct_IO() in generic_file_direct_write() call, but I decided to fix dio_complete() too so we don't leave a landmine there, also be consistent with iomap_dio_complete(). Fixes: 332391a9935d ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO") Signed-off-by: Eryu Guan <eguan@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Lukas Czerner <lczerner@redhat.com>
2017-10-13 16:47:46 +00:00
if (offset + ret > dio->i_size &&
!(dio->flags & IOMAP_DIO_WRITE))
fs: invalidate page cache after end_io() in dio completion Commit 332391a9935d ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO") moved page cache invalidation from iomap_dio_rw() to iomap_dio_complete() for iomap based direct write path, but before the dio->end_io() call, and it re-introdued the bug fixed by commit c771c14baa33 ("iomap: invalidate page caches should be after iomap_dio_complete() in direct write"). I found this because fstests generic/418 started failing on XFS with v4.14-rc3 kernel, which is the regression test for this specific bug. So similarly, fix it by moving dio->end_io() (which does the unwritten extent conversion) before page cache invalidation, to make sure next buffer read reads the final real allocations not unwritten extents. I also add some comments about why should end_io() go first in case we get it wrong again in the future. Note that, there's no such problem in the non-iomap based direct write path, because we didn't remove the page cache invalidation after the ->direct_IO() in generic_file_direct_write() call, but I decided to fix dio_complete() too so we don't leave a landmine there, also be consistent with iomap_dio_complete(). Fixes: 332391a9935d ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO") Signed-off-by: Eryu Guan <eguan@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Lukas Czerner <lczerner@redhat.com>
2017-10-13 16:47:46 +00:00
ret = dio->i_size - offset;
iocb->ki_pos += ret;
}
fs: invalidate page cache after end_io() in dio completion Commit 332391a9935d ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO") moved page cache invalidation from iomap_dio_rw() to iomap_dio_complete() for iomap based direct write path, but before the dio->end_io() call, and it re-introdued the bug fixed by commit c771c14baa33 ("iomap: invalidate page caches should be after iomap_dio_complete() in direct write"). I found this because fstests generic/418 started failing on XFS with v4.14-rc3 kernel, which is the regression test for this specific bug. So similarly, fix it by moving dio->end_io() (which does the unwritten extent conversion) before page cache invalidation, to make sure next buffer read reads the final real allocations not unwritten extents. I also add some comments about why should end_io() go first in case we get it wrong again in the future. Note that, there's no such problem in the non-iomap based direct write path, because we didn't remove the page cache invalidation after the ->direct_IO() in generic_file_direct_write() call, but I decided to fix dio_complete() too so we don't leave a landmine there, also be consistent with iomap_dio_complete(). Fixes: 332391a9935d ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO") Signed-off-by: Eryu Guan <eguan@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Lukas Czerner <lczerner@redhat.com>
2017-10-13 16:47:46 +00:00
/*
* Try again to invalidate clean pages which might have been cached by
* non-direct readahead, or faulted in by get_user_pages() if the source
* of the write was an mmap'ed region of the file we're writing. Either
* one is a pretty crazy thing to do, so we don't support it 100%. If
* this invalidation fails, tough, the write still worked...
*
* And this page cache invalidation has to be after dio->end_io(), as
* some filesystems convert unwritten extents to real allocations in
* end_io() when necessary, otherwise a racing buffer read would cache
* zeros from unwritten extents.
*/
if (!dio->error &&
(dio->flags & IOMAP_DIO_WRITE) && inode->i_mapping->nrpages) {
int err;
err = invalidate_inode_pages2_range(inode->i_mapping,
offset >> PAGE_SHIFT,
(offset + dio->size - 1) >> PAGE_SHIFT);
if (err)
dio_warn_stale_pagecache(iocb->ki_filp);
fs: invalidate page cache after end_io() in dio completion Commit 332391a9935d ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO") moved page cache invalidation from iomap_dio_rw() to iomap_dio_complete() for iomap based direct write path, but before the dio->end_io() call, and it re-introdued the bug fixed by commit c771c14baa33 ("iomap: invalidate page caches should be after iomap_dio_complete() in direct write"). I found this because fstests generic/418 started failing on XFS with v4.14-rc3 kernel, which is the regression test for this specific bug. So similarly, fix it by moving dio->end_io() (which does the unwritten extent conversion) before page cache invalidation, to make sure next buffer read reads the final real allocations not unwritten extents. I also add some comments about why should end_io() go first in case we get it wrong again in the future. Note that, there's no such problem in the non-iomap based direct write path, because we didn't remove the page cache invalidation after the ->direct_IO() in generic_file_direct_write() call, but I decided to fix dio_complete() too so we don't leave a landmine there, also be consistent with iomap_dio_complete(). Fixes: 332391a9935d ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO") Signed-off-by: Eryu Guan <eguan@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Lukas Czerner <lczerner@redhat.com>
2017-10-13 16:47:46 +00:00
}
/*
* If this is a DSYNC write, make sure we push it to stable storage now
* that we've written data.
*/
if (ret > 0 && (dio->flags & IOMAP_DIO_NEED_SYNC))
ret = generic_write_sync(iocb, ret);
inode_dio_end(file_inode(iocb->ki_filp));
kfree(dio);
return ret;
}
static void iomap_dio_complete_work(struct work_struct *work)
{
struct iomap_dio *dio = container_of(work, struct iomap_dio, aio.work);
struct kiocb *iocb = dio->iocb;
iocb->ki_complete(iocb, iomap_dio_complete(dio), 0);
}
/*
* Set an error in the dio if none is set yet. We have to use cmpxchg
* as the submission context and the completion context(s) can race to
* update the error.
*/
static inline void iomap_dio_set_error(struct iomap_dio *dio, int ret)
{
cmpxchg(&dio->error, 0, ret);
}
static void iomap_dio_bio_end_io(struct bio *bio)
{
struct iomap_dio *dio = bio->bi_private;
bool should_dirty = (dio->flags & IOMAP_DIO_DIRTY);
if (bio->bi_status)
iomap_dio_set_error(dio, blk_status_to_errno(bio->bi_status));
if (atomic_dec_and_test(&dio->ref)) {
if (dio->wait_for_completion) {
struct task_struct *waiter = dio->submit.waiter;
WRITE_ONCE(dio->submit.waiter, NULL);
wake_up_process(waiter);
} else if (dio->flags & IOMAP_DIO_WRITE) {
struct inode *inode = file_inode(dio->iocb->ki_filp);
INIT_WORK(&dio->aio.work, iomap_dio_complete_work);
queue_work(inode->i_sb->s_dio_done_wq, &dio->aio.work);
} else {
iomap_dio_complete_work(&dio->aio.work);
}
}
if (should_dirty) {
bio_check_pages_dirty(bio);
} else {
struct bio_vec *bvec;
int i;
bio_for_each_segment_all(bvec, bio, i)
put_page(bvec->bv_page);
bio_put(bio);
}
}
static blk_qc_t
iomap_dio_zero(struct iomap_dio *dio, struct iomap *iomap, loff_t pos,
unsigned len)
{
struct page *page = ZERO_PAGE(0);
struct bio *bio;
bio = bio_alloc(GFP_KERNEL, 1);
bio_set_dev(bio, iomap->bdev);
bio->bi_iter.bi_sector = iomap_sector(iomap, pos);
bio->bi_private = dio;
bio->bi_end_io = iomap_dio_bio_end_io;
get_page(page);
__bio_add_page(bio, page, len, 0);
xfs: updates for 4.10-rc1 Contained in this update: - DAX PMD vaults via iomap infrastructure - Direct-io support in iomap infrastructure - removal of now-redundant XFS inode iolock, replaced with VFS i_rwsem - synchronisation with fixes and changes in userspace libxfs code - extent tree lookup helpers - lots of little corruption detection improvements to verifiers - optimised CRC calculations - faster buffer cache lookups - deprecation of barrier/nobarrier mount options - we always use REQ_FUA/REQ_FLUSH where appropriate for data integrity now - cleanups to speculative preallocation - miscellaneous minor bug fixes and cleanups -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJYUgqdAAoJEK3oKUf0dfodQgsP/1dJ4qUc6cRk8kL+f10FoIek oFzdViRHZj8cROGe2n2YTBJtPa9KjU5DNHnxaxWZBN4ZpItp/uN1sAQhgtNQ4/cN C3JF6B/+/dIbNSbd7DwvSl0dMWknzmrB+Myfs2ZPpMA1S4GInk1MOJSj7AQdYAvJ dS0dQWAuIB20cahwuGA4y7zUniYL1IcF/BH8hlmzpcUNUoJ9AkR1hTg5/aVfmga3 w2p1vZyT2E4xs/Ff4FYW5MzPGxLVQMZVNIAXAcJl+c61z46ndXqidSmVHGvc+Tlt ouxftHy/7KqowZlCFss1pSXg9HlXHhjS+iLbZerfcjO2qldriZS+QqQyASmQzPAz +PpnMfVOj+yjsXKyIHWuS1G35aV16pPWwdA0ECeU6yv9iZ7tSz5rvSrsPZPLFz4x RVhcKbmXR3y8DugkmtznU5ozxPt5hbbstEV3leCzxJpZu5reRJThUW7nYkSd0CEJ ZyT/GP6Aq/MM8O/hOgVutAH409dsrYok8m/lq1J7VbNUt8inylcsMWsBeX/0/AHY aC7I2Vx8bnbfL+C8wYKYhuShOGSch93O5hDUXdH2K/Sm5cK4y2asWge6MfFsS6Lu waVYwd5aYBlNbzkvUMm2I5EV4cCCR3YwWYwfBEP7kPYUDxN14huOz6lVXnQPDLQ1 qsV1aNfK9PPiw6Fcaop0 =HwDG -----END PGP SIGNATURE----- Merge tag 'xfs-for-linus-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs Pull xfs updates from Dave Chinner: "There is quite a varied bunch of stuff in this update, and some of it you will have already merged through the ext4 tree which imported the dax-4.10-iomap-pmd topic branch from the XFS tree. There is also a new direct IO implementation that uses the iomap infrastructure. It's much simpler, faster, and has lower IO latency than the existing direct IO infrastructure. Summary: - DAX PMD faults via iomap infrastructure - Direct-io support in iomap infrastructure - removal of now-redundant XFS inode iolock, replaced with VFS i_rwsem - synchronisation with fixes and changes in userspace libxfs code - extent tree lookup helpers - lots of little corruption detection improvements to verifiers - optimised CRC calculations - faster buffer cache lookups - deprecation of barrier/nobarrier mount options - we always use REQ_FUA/REQ_FLUSH where appropriate for data integrity now - cleanups to speculative preallocation - miscellaneous minor bug fixes and cleanups" * tag 'xfs-for-linus-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (63 commits) xfs: nuke unused tracepoint definitions xfs: use GPF_NOFS when allocating btree cursors xfs: use xfs_vn_setattr_size to check on new size xfs: deprecate barrier/nobarrier mount option xfs: Always flush caches when integrity is required xfs: ignore leaf attr ichdr.count in verifier during log replay xfs: use rhashtable to track buffer cache xfs: optimise CRC updates xfs: make xfs btree stats less huge xfs: don't cap maximum dedupe request length xfs: don't allow di_size with high bit set xfs: error out if trying to add attrs and anextents > 0 xfs: don't crash if reading a directory results in an unexpected hole xfs: complain if we don't get nextents bmap records xfs: check for bogus values in btree block headers xfs: forbid AG btrees with level == 0 xfs: several xattr functions can be void xfs: handle cow fork in xfs_bmap_trace_exlist xfs: pass state not whichfork to trace_xfs_extlist xfs: Move AGI buffer type setting to xfs_read_agi ...
2016-12-15 05:35:31 +00:00
bio_set_op_attrs(bio, REQ_OP_WRITE, REQ_SYNC | REQ_IDLE);
atomic_inc(&dio->ref);
return submit_bio(bio);
}
static loff_t
iomap_dio_actor(struct inode *inode, loff_t pos, loff_t length,
void *data, struct iomap *iomap)
{
struct iomap_dio *dio = data;
unsigned int blkbits = blksize_bits(bdev_logical_block_size(iomap->bdev));
unsigned int fs_block_size = i_blocksize(inode), pad;
unsigned int align = iov_iter_alignment(dio->submit.iter);
struct iov_iter iter;
struct bio *bio;
bool need_zeroout = false;
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
bool use_fua = false;
int nr_pages, ret;
size_t copied = 0;
if ((pos | length | align) & ((1 << blkbits) - 1))
return -EINVAL;
switch (iomap->type) {
case IOMAP_HOLE:
if (WARN_ON_ONCE(dio->flags & IOMAP_DIO_WRITE))
return -EIO;
/*FALLTHRU*/
case IOMAP_UNWRITTEN:
if (!(dio->flags & IOMAP_DIO_WRITE)) {
length = iov_iter_zero(length, dio->submit.iter);
dio->size += length;
return length;
}
dio->flags |= IOMAP_DIO_UNWRITTEN;
need_zeroout = true;
break;
case IOMAP_MAPPED:
if (iomap->flags & IOMAP_F_SHARED)
dio->flags |= IOMAP_DIO_COW;
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
if (iomap->flags & IOMAP_F_NEW) {
need_zeroout = true;
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
} else {
/*
* Use a FUA write if we need datasync semantics, this
* is a pure data IO that doesn't require any metadata
* updates and the underlying device supports FUA. This
* allows us to avoid cache flushes on IO completion.
*/
if (!(iomap->flags & (IOMAP_F_SHARED|IOMAP_F_DIRTY)) &&
(dio->flags & IOMAP_DIO_WRITE_FUA) &&
blk_queue_fua(bdev_get_queue(iomap->bdev)))
use_fua = true;
}
break;
default:
WARN_ON_ONCE(1);
return -EIO;
}
/*
* Operate on a partial iter trimmed to the extent we were called for.
* We'll update the iter in the dio once we're done with this extent.
*/
iter = *dio->submit.iter;
iov_iter_truncate(&iter, length);
nr_pages = iov_iter_npages(&iter, BIO_MAX_PAGES);
if (nr_pages <= 0)
return nr_pages;
if (need_zeroout) {
/* zero out from the start of the block to the write offset */
pad = pos & (fs_block_size - 1);
if (pad)
iomap_dio_zero(dio, iomap, pos - pad, pad);
}
do {
size_t n;
if (dio->error) {
iov_iter_revert(dio->submit.iter, copied);
return 0;
}
bio = bio_alloc(GFP_KERNEL, nr_pages);
bio_set_dev(bio, iomap->bdev);
bio->bi_iter.bi_sector = iomap_sector(iomap, pos);
bio->bi_write_hint = dio->iocb->ki_hint;
bio->bi_ioprio = dio->iocb->ki_ioprio;
bio->bi_private = dio;
bio->bi_end_io = iomap_dio_bio_end_io;
ret = bio_iov_iter_get_pages(bio, &iter);
if (unlikely(ret)) {
bio_put(bio);
return copied ? copied : ret;
}
n = bio->bi_iter.bi_size;
if (dio->flags & IOMAP_DIO_WRITE) {
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
bio->bi_opf = REQ_OP_WRITE | REQ_SYNC | REQ_IDLE;
if (use_fua)
bio->bi_opf |= REQ_FUA;
else
dio->flags &= ~IOMAP_DIO_WRITE_FUA;
task_io_account_write(n);
} else {
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
bio->bi_opf = REQ_OP_READ;
if (dio->flags & IOMAP_DIO_DIRTY)
bio_set_pages_dirty(bio);
}
iov_iter_advance(dio->submit.iter, n);
dio->size += n;
pos += n;
copied += n;
nr_pages = iov_iter_npages(&iter, BIO_MAX_PAGES);
atomic_inc(&dio->ref);
dio->submit.last_queue = bdev_get_queue(iomap->bdev);
dio->submit.cookie = submit_bio(bio);
} while (nr_pages);
if (need_zeroout) {
/* zero out from the end of the write to the end of the block */
pad = pos & (fs_block_size - 1);
if (pad)
iomap_dio_zero(dio, iomap, pos, fs_block_size - pad);
}
return copied;
}
/*
* iomap_dio_rw() always completes O_[D]SYNC writes regardless of whether the IO
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
* is being issued as AIO or not. This allows us to optimise pure data writes
* to use REQ_FUA rather than requiring generic_write_sync() to issue a
* REQ_FLUSH post write. This is slightly tricky because a single request here
* can be mapped into multiple disjoint IOs and only a subset of the IOs issued
* may be pure data writes. In that case, we still need to do a full data sync
* completion.
*/
ssize_t
iomap_dio_rw(struct kiocb *iocb, struct iov_iter *iter,
const struct iomap_ops *ops, iomap_dio_end_io_t end_io)
{
struct address_space *mapping = iocb->ki_filp->f_mapping;
struct inode *inode = file_inode(iocb->ki_filp);
size_t count = iov_iter_count(iter);
iomap: invalidate page caches should be after iomap_dio_complete() in direct write After XFS switching to iomap based DIO (commit acdda3aae146 ("xfs: use iomap_dio_rw")), I started to notice dio29/dio30 tests failures from LTP run on ppc64 hosts, and they can be reproduced on x86_64 hosts with 512B/1k block size XFS too. dio29 diotest3 -b 65536 -n 100 -i 1000 -o 1024000 dio30 diotest6 -b 65536 -n 100 -i 1000 -o 1024000 The failure message is like: bufcmp: offset 0: Expected: 0x62, got 0x0 diotest03 1 TPASS : Read with Direct IO, Write without diotest03 2 TFAIL : diotest3.c:142: comparsion failed; child=98 offset=1425408 diotest03 3 TFAIL : diotest3.c:194: Write Direct-child 98 failed Direct write wrote 0x62 but buffer read got zero. This is because, when doing direct write to a hole or preallocated file, we invalidate the page caches before converting the extent from unwritten state to normal state, which is done by iomap_dio_complete(), thus leave a window for other buffer reader to cache the unwritten state extent. Consider this case, with sub-page blocksize XFS, two processes are direct writing to different blocksize-aligned regions (say 512B) of the same preallocated file, and reading the region back via buffered I/O to compare contents. process A, region [0,512] process B, region [512,1024] xfs_file_write_iter xfs_file_aio_dio_write iomap_dio_rw iomap_apply invalidate_inode_pages2_range xfs_file_write_iter xfs_file_aio_dio_write iomap_dio_rw iomap_apply invalidate_inode_pages2_range iomap_dio_complete xfs_file_read_iter xfs_file_buffered_aio_read generic_file_read_iter do_generic_file_read <readahead fills pagecache with 0> iomap_dio_complete xfs_file_read_iter <read gets 0 from pagecache> Process A first invalidates page caches, at this point the underlying extent is still in unwritten state (iomap_dio_complete not called yet), and process B finishs direct write and populates page caches via readahead, which caches zeros in page for region A, then process A reads zeros from page cache, instead of the actual data. Fix it by invalidating page caches after converting unwritten extent to make sure we read content from disk after extent state changed, as what we did before switching to iomap based dio. Also introduce a new 'start' variable to save the original write offset (iomap_dio_complete() updates iocb->ki_pos), and a 'err' variable for invalidating caches result, cause we can't reuse 'ret' anymore. Signed-off-by: Eryu Guan <eguan@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2017-03-02 23:02:06 +00:00
loff_t pos = iocb->ki_pos, start = pos;
loff_t end = iocb->ki_pos + count - 1, ret = 0;
unsigned int flags = IOMAP_DIRECT;
struct blk_plug plug;
struct iomap_dio *dio;
lockdep_assert_held(&inode->i_rwsem);
if (!count)
return 0;
dio = kmalloc(sizeof(*dio), GFP_KERNEL);
if (!dio)
return -ENOMEM;
dio->iocb = iocb;
atomic_set(&dio->ref, 1);
dio->size = 0;
dio->i_size = i_size_read(inode);
dio->end_io = end_io;
dio->error = 0;
dio->flags = 0;
dio->wait_for_completion = is_sync_kiocb(iocb);
dio->submit.iter = iter;
dio->submit.waiter = current;
dio->submit.cookie = BLK_QC_T_NONE;
dio->submit.last_queue = NULL;
if (iov_iter_rw(iter) == READ) {
if (pos >= dio->i_size)
goto out_free_dio;
if (iter->type == ITER_IOVEC)
dio->flags |= IOMAP_DIO_DIRTY;
} else {
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
flags |= IOMAP_WRITE;
dio->flags |= IOMAP_DIO_WRITE;
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
/* for data sync or sync, we need sync completion processing */
if (iocb->ki_flags & IOCB_DSYNC)
dio->flags |= IOMAP_DIO_NEED_SYNC;
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
/*
* For datasync only writes, we optimistically try using FUA for
* this IO. Any non-FUA write that occurs will clear this flag,
* hence we know before completion whether a cache flush is
* necessary.
*/
if ((iocb->ki_flags & (IOCB_DSYNC | IOCB_SYNC)) == IOCB_DSYNC)
dio->flags |= IOMAP_DIO_WRITE_FUA;
}
if (iocb->ki_flags & IOCB_NOWAIT) {
if (filemap_range_has_page(mapping, start, end)) {
ret = -EAGAIN;
goto out_free_dio;
}
flags |= IOMAP_NOWAIT;
}
fs: fix data invalidation in the cleancache during direct IO Patch series "Properly invalidate data in the cleancache", v2. We've noticed that after direct IO write, buffered read sometimes gets stale data which is coming from the cleancache. The reason for this is that some direct write hooks call call invalidate_inode_pages2[_range]() conditionally iff mapping->nrpages is not zero, so we may not invalidate data in the cleancache. Another odd thing is that we check only for ->nrpages and don't check for ->nrexceptional, but invalidate_inode_pages2[_range] also invalidates exceptional entries as well. So we invalidate exceptional entries only if ->nrpages != 0? This doesn't feel right. - Patch 1 fixes direct IO writes by removing ->nrpages check. - Patch 2 fixes similar case in invalidate_bdev(). Note: I only fixed conditional cleancache_invalidate_inode() here. Do we also need to add ->nrexceptional check in into invalidate_bdev()? - Patches 3-4: some optimizations. This patch (of 4): Some direct IO write fs hooks call invalidate_inode_pages2[_range]() conditionally iff mapping->nrpages is not zero. This can't be right, because invalidate_inode_pages2[_range]() also invalidate data in the cleancache via cleancache_invalidate_inode() call. So if page cache is empty but there is some data in the cleancache, buffered read after direct IO write would get stale data from the cleancache. Also it doesn't feel right to check only for ->nrpages because invalidate_inode_pages2[_range] invalidates exceptional entries as well. Fix this by calling invalidate_inode_pages2[_range]() regardless of nrpages state. Note: nfs,cifs,9p doesn't need similar fix because the never call cleancache_get_page() (nor directly, nor via mpage_readpage[s]()), so they are not affected by this bug. Fixes: c515e1fd361c ("mm/fs: add hooks to support cleancache") Link: http://lkml.kernel.org/r/20170424164135.22350-2-aryabinin@virtuozzo.com Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Jan Kara <jack@suse.cz> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Alexey Kuznetsov <kuznet@virtuozzo.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Nikolay Borisov <n.borisov.lkml@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-05-03 21:55:59 +00:00
ret = filemap_write_and_wait_range(mapping, start, end);
if (ret)
goto out_free_dio;
/*
* Try to invalidate cache pages for the range we're direct
* writing. If this invalidation fails, tough, the write will
* still work, but racing two incompatible write paths is a
* pretty crazy thing to do, so we don't support it 100%.
*/
fs: fix data invalidation in the cleancache during direct IO Patch series "Properly invalidate data in the cleancache", v2. We've noticed that after direct IO write, buffered read sometimes gets stale data which is coming from the cleancache. The reason for this is that some direct write hooks call call invalidate_inode_pages2[_range]() conditionally iff mapping->nrpages is not zero, so we may not invalidate data in the cleancache. Another odd thing is that we check only for ->nrpages and don't check for ->nrexceptional, but invalidate_inode_pages2[_range] also invalidates exceptional entries as well. So we invalidate exceptional entries only if ->nrpages != 0? This doesn't feel right. - Patch 1 fixes direct IO writes by removing ->nrpages check. - Patch 2 fixes similar case in invalidate_bdev(). Note: I only fixed conditional cleancache_invalidate_inode() here. Do we also need to add ->nrexceptional check in into invalidate_bdev()? - Patches 3-4: some optimizations. This patch (of 4): Some direct IO write fs hooks call invalidate_inode_pages2[_range]() conditionally iff mapping->nrpages is not zero. This can't be right, because invalidate_inode_pages2[_range]() also invalidate data in the cleancache via cleancache_invalidate_inode() call. So if page cache is empty but there is some data in the cleancache, buffered read after direct IO write would get stale data from the cleancache. Also it doesn't feel right to check only for ->nrpages because invalidate_inode_pages2[_range] invalidates exceptional entries as well. Fix this by calling invalidate_inode_pages2[_range]() regardless of nrpages state. Note: nfs,cifs,9p doesn't need similar fix because the never call cleancache_get_page() (nor directly, nor via mpage_readpage[s]()), so they are not affected by this bug. Fixes: c515e1fd361c ("mm/fs: add hooks to support cleancache") Link: http://lkml.kernel.org/r/20170424164135.22350-2-aryabinin@virtuozzo.com Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Jan Kara <jack@suse.cz> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Alexey Kuznetsov <kuznet@virtuozzo.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Nikolay Borisov <n.borisov.lkml@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-05-03 21:55:59 +00:00
ret = invalidate_inode_pages2_range(mapping,
start >> PAGE_SHIFT, end >> PAGE_SHIFT);
if (ret)
dio_warn_stale_pagecache(iocb->ki_filp);
fs: fix data invalidation in the cleancache during direct IO Patch series "Properly invalidate data in the cleancache", v2. We've noticed that after direct IO write, buffered read sometimes gets stale data which is coming from the cleancache. The reason for this is that some direct write hooks call call invalidate_inode_pages2[_range]() conditionally iff mapping->nrpages is not zero, so we may not invalidate data in the cleancache. Another odd thing is that we check only for ->nrpages and don't check for ->nrexceptional, but invalidate_inode_pages2[_range] also invalidates exceptional entries as well. So we invalidate exceptional entries only if ->nrpages != 0? This doesn't feel right. - Patch 1 fixes direct IO writes by removing ->nrpages check. - Patch 2 fixes similar case in invalidate_bdev(). Note: I only fixed conditional cleancache_invalidate_inode() here. Do we also need to add ->nrexceptional check in into invalidate_bdev()? - Patches 3-4: some optimizations. This patch (of 4): Some direct IO write fs hooks call invalidate_inode_pages2[_range]() conditionally iff mapping->nrpages is not zero. This can't be right, because invalidate_inode_pages2[_range]() also invalidate data in the cleancache via cleancache_invalidate_inode() call. So if page cache is empty but there is some data in the cleancache, buffered read after direct IO write would get stale data from the cleancache. Also it doesn't feel right to check only for ->nrpages because invalidate_inode_pages2[_range] invalidates exceptional entries as well. Fix this by calling invalidate_inode_pages2[_range]() regardless of nrpages state. Note: nfs,cifs,9p doesn't need similar fix because the never call cleancache_get_page() (nor directly, nor via mpage_readpage[s]()), so they are not affected by this bug. Fixes: c515e1fd361c ("mm/fs: add hooks to support cleancache") Link: http://lkml.kernel.org/r/20170424164135.22350-2-aryabinin@virtuozzo.com Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Jan Kara <jack@suse.cz> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Alexey Kuznetsov <kuznet@virtuozzo.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Nikolay Borisov <n.borisov.lkml@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-05-03 21:55:59 +00:00
ret = 0;
if (iov_iter_rw(iter) == WRITE && !dio->wait_for_completion &&
iomap_dio_rw: Allocate AIO completion queue before submitting dio Executing xfs/104 test in a loop on Linux-v4.13 kernel on a ppc64 machine can cause the following NULL pointer dereference, .queue_work_on+0x4c/0x80 .iomap_dio_bio_end_io+0xbc/0x1f0 .bio_endio+0x118/0x1f0 .blk_update_request+0xd0/0x470 .blk_mq_end_request+0x24/0xc0 .lo_complete_rq+0x40/0xe0 .__blk_mq_complete_request_remote+0x28/0x40 .flush_smp_call_function_queue+0xc4/0x1e0 .smp_ipi_demux_relaxed+0x8c/0x100 .icp_hv_ipi_action+0x54/0xa0 .__handle_irq_event_percpu+0x84/0x2c0 .handle_irq_event_percpu+0x28/0x80 .handle_percpu_irq+0x78/0xc0 .generic_handle_irq+0x40/0x70 .__do_irq+0x88/0x200 .call_do_irq+0x14/0x24 .do_IRQ+0x84/0x130 This occurs due to the following sequence of events, 1. Allocate dio for Direct I/O write. 2. Invoke iomap_apply() until iov_iter_count() bytes have been submitted. - Assume that we have submitted atleast one bio. Hence iomap_dio->ref value will be >= 2. - If during the second iteration, iomap_apply() ends up returning -ENOSPC, we would break out of the loop and since the 'ret' value is a negative number we end up not allocating memory for super_block->s_dio_done_wq. 3. Meanwhile, iomap_dio_bio_end_io() is invoked for bios that have been submitted and here the code ends up dereferencing the NULL pointer stored at super_block->s_dio_done_wq. This commit fixes the bug by allocating memory for super_block->s_dio_done_wq before iomap_apply() is invoked. Reported-by: Eryu Guan <eguan@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: Eryu Guan <eguan@redhat.com> Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2017-09-22 18:47:33 +00:00
!inode->i_sb->s_dio_done_wq) {
ret = sb_init_dio_done_wq(inode->i_sb);
if (ret < 0)
goto out_free_dio;
}
inode_dio_begin(inode);
blk_start_plug(&plug);
do {
ret = iomap_apply(inode, pos, count, flags, ops, dio,
iomap_dio_actor);
if (ret <= 0) {
/* magic error code to fall back to buffered I/O */
if (ret == -ENOTBLK) {
dio->wait_for_completion = true;
ret = 0;
}
break;
}
pos += ret;
iomap_dio_rw: Prevent reading file data beyond iomap_dio->i_size On a ppc64 machine executing overlayfs/019 with xfs as the lower and upper filesystem causes the following call trace, WARNING: CPU: 2 PID: 8034 at /root/repos/linux/fs/iomap.c:765 .iomap_dio_actor+0xcc/0x420 Modules linked in: CPU: 2 PID: 8034 Comm: fsstress Tainted: G L 4.11.0-rc5-next-20170405 #100 task: c000000631314880 task.stack: c0000003915d4000 NIP: c00000000035a72c LR: c00000000035a6f4 CTR: c00000000035a660 REGS: c0000003915d7570 TRAP: 0700 Tainted: G L (4.11.0-rc5-next-20170405) MSR: 800000000282b032 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI> CR: 24004284 XER: 00000000 CFAR: c0000000006f7190 SOFTE: 1 GPR00: c00000000035a6f4 c0000003915d77f0 c0000000015a3f00 000000007c22f600 GPR04: 000000000022d000 0000000000002600 c0000003b2d56360 c0000003915d7960 GPR08: c0000003915d7cd0 0000000000000002 0000000000002600 c000000000521cc0 GPR12: 0000000024004284 c00000000fd80a00 000000004b04ae64 ffffffffffffffff GPR16: 000000001000ca70 0000000000000000 c0000003b2d56380 c00000000153d2b8 GPR20: 0000000000000010 c0000003bc87bac8 0000000000223000 000000000022f5ff GPR24: c0000003b2d56360 000000000000000c 0000000000002600 000000000022d000 GPR28: 0000000000000000 c0000003915d7960 c0000003b2d56360 00000000000001ff NIP [c00000000035a72c] .iomap_dio_actor+0xcc/0x420 LR [c00000000035a6f4] .iomap_dio_actor+0x94/0x420 Call Trace: [c0000003915d77f0] [c00000000035a6f4] .iomap_dio_actor+0x94/0x420 (unreliable) [c0000003915d78f0] [c00000000035b9f4] .iomap_apply+0xf4/0x1f0 [c0000003915d79d0] [c00000000035c320] .iomap_dio_rw+0x230/0x420 [c0000003915d7ae0] [c000000000512a14] .xfs_file_dio_aio_read+0x84/0x160 [c0000003915d7b80] [c000000000512d24] .xfs_file_read_iter+0x104/0x130 [c0000003915d7c10] [c0000000002d6234] .__vfs_read+0x114/0x1a0 [c0000003915d7cf0] [c0000000002d7a8c] .vfs_read+0xac/0x1a0 [c0000003915d7d90] [c0000000002d96b8] .SyS_read+0x58/0x100 [c0000003915d7e30] [c00000000000b8e0] system_call+0x38/0xfc Instruction dump: 78630020 7f831b78 7ffc07b4 7c7ce039 40820360 a13d0018 2f890003 419e0288 2f890004 419e00a0 2f890001 419e02a8 <0fe00000> 3b80fffb 38210100 7f83e378 The above problem can also be recreated on a regular xfs filesystem using the command, $ fsstress -d /mnt -l 1000 -n 1000 -p 1000 The reason for the call trace is, 1. When 'reserving' blocks for delayed allocation , XFS reserves more blocks (i.e. past file's current EOF) than required. This is done because XFS assumes that userspace might write more data and hence 'reserving' more blocks might lead to the file's new data being stored contiguously on disk. 2. The in-memory 'struct xfs_bmbt_irec' mapping the file's last extent would then cover the prealloc-ed EOF blocks in addition to the regular blocks. 3. When flushing the dirty blocks to disk, we only flush data till the file's EOF. But before writing out the dirty data, we allocate blocks on the disk for holding the file's new data. This allocation includes the blocks that are part of the 'prealloc EOF blocks'. 4. Later, when the last reference to the inode is being closed, XFS frees the unused 'prealloc EOF blocks' in xfs_inactive(). In step 3 above, When allocating space on disk for the delayed allocation range, the space allocator might sometimes allocate less blocks than required. If such an allocation ends right at the current EOF of the file, We will not be able to clear the "delayed allocation" flag for the 'prealloc EOF blocks', since we won't have dirty buffer heads associated with that range of the file. In such a situation if a Direct I/O read operation is performed on file range [X, Y] (where X < EOF and Y > EOF), we flush dirty data in the range [X, Y] and invalidate page cache for that range (Refer to iomap_dio_rw()). Later for performing the Direct I/O read, XFS obtains the extent items (which are still cached in memory) for the file range. When doing so we are not supposed to get an extent item with IOMAP_DELALLOC flag set, since the previous "flush" operation should have converted any delayed allocation data in the range [X, Y]. Hence we end up hitting a WARN_ON_ONCE(1) statement in iomap_dio_actor(). This commit fixes the bug by preventing the read operation from going beyond iomap_dio->i_size. Reported-by: Santhosh G <santhog4@linux.vnet.ibm.com> Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2017-04-12 18:03:20 +00:00
if (iov_iter_rw(iter) == READ && pos >= dio->i_size)
break;
} while ((count = iov_iter_count(iter)) > 0);
blk_finish_plug(&plug);
if (ret < 0)
iomap_dio_set_error(dio, ret);
iomap: Use FUA for pure data O_DSYNC DIO writes If we are doing direct IO writes with datasync semantics, we often have to flush metadata changes along with the data write. However, if we are overwriting existing data, there are no metadata changes that we need to flush. In this case, optimising the IO by using FUA write makes sense. We know from the IOMAP_F_DIRTY flag as to whether a specific inode requires a metadata flush - this is currently used by DAX to ensure extent modification as stable in page fault operations. For direct IO writes, we can use it to determine if we need to flush metadata or not once the data is on disk. Hence if we have been returned a mapped extent that is not new and the IO mapping is not dirty, then we can use a FUA write to provide datasync semantics. This allows us to short-cut the generic_write_sync() call in IO completion and hence avoid unnecessary operations. This makes pure direct IO data write behaviour identical to the way block devices use REQ_FUA to provide datasync semantics. On a FUA enabled device, a synchronous direct IO write workload (sequential 4k overwrites in 32MB file) had the following results: # xfs_io -fd -c "pwrite -V 1 -D 0 32m" /mnt/scratch/boo kernel time write()s write iops Write b/w ------ ---- -------- ---------- --------- (no dsync) 4s 2173/s 2173 8.5MB/s vanilla 22s 370/s 750 1.4MB/s patched 19s 420/s 420 1.6MB/s The patched code clearly doesn't send cache flushes anymore, but instead uses FUA (confirmed via blktrace), and performance improves a bit as a result. However, the benefits will be higher on workloads that mix O_DSYNC overwrites with other write IO as we won't be flushing the entire device cache on every DSYNC overwrite IO anymore. Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2018-05-02 19:54:53 +00:00
/*
* If all the writes we issued were FUA, we don't need to flush the
* cache on IO completion. Clear the sync flag for this case.
*/
if (dio->flags & IOMAP_DIO_WRITE_FUA)
dio->flags &= ~IOMAP_DIO_NEED_SYNC;
if (!atomic_dec_and_test(&dio->ref)) {
if (!dio->wait_for_completion)
return -EIOCBQUEUED;
for (;;) {
set_current_state(TASK_UNINTERRUPTIBLE);
if (!READ_ONCE(dio->submit.waiter))
break;
if (!(iocb->ki_flags & IOCB_HIPRI) ||
!dio->submit.last_queue ||
!blk_poll(dio->submit.last_queue,
xfs: updates for 4.10-rc1 Contained in this update: - DAX PMD vaults via iomap infrastructure - Direct-io support in iomap infrastructure - removal of now-redundant XFS inode iolock, replaced with VFS i_rwsem - synchronisation with fixes and changes in userspace libxfs code - extent tree lookup helpers - lots of little corruption detection improvements to verifiers - optimised CRC calculations - faster buffer cache lookups - deprecation of barrier/nobarrier mount options - we always use REQ_FUA/REQ_FLUSH where appropriate for data integrity now - cleanups to speculative preallocation - miscellaneous minor bug fixes and cleanups -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJYUgqdAAoJEK3oKUf0dfodQgsP/1dJ4qUc6cRk8kL+f10FoIek oFzdViRHZj8cROGe2n2YTBJtPa9KjU5DNHnxaxWZBN4ZpItp/uN1sAQhgtNQ4/cN C3JF6B/+/dIbNSbd7DwvSl0dMWknzmrB+Myfs2ZPpMA1S4GInk1MOJSj7AQdYAvJ dS0dQWAuIB20cahwuGA4y7zUniYL1IcF/BH8hlmzpcUNUoJ9AkR1hTg5/aVfmga3 w2p1vZyT2E4xs/Ff4FYW5MzPGxLVQMZVNIAXAcJl+c61z46ndXqidSmVHGvc+Tlt ouxftHy/7KqowZlCFss1pSXg9HlXHhjS+iLbZerfcjO2qldriZS+QqQyASmQzPAz +PpnMfVOj+yjsXKyIHWuS1G35aV16pPWwdA0ECeU6yv9iZ7tSz5rvSrsPZPLFz4x RVhcKbmXR3y8DugkmtznU5ozxPt5hbbstEV3leCzxJpZu5reRJThUW7nYkSd0CEJ ZyT/GP6Aq/MM8O/hOgVutAH409dsrYok8m/lq1J7VbNUt8inylcsMWsBeX/0/AHY aC7I2Vx8bnbfL+C8wYKYhuShOGSch93O5hDUXdH2K/Sm5cK4y2asWge6MfFsS6Lu waVYwd5aYBlNbzkvUMm2I5EV4cCCR3YwWYwfBEP7kPYUDxN14huOz6lVXnQPDLQ1 qsV1aNfK9PPiw6Fcaop0 =HwDG -----END PGP SIGNATURE----- Merge tag 'xfs-for-linus-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs Pull xfs updates from Dave Chinner: "There is quite a varied bunch of stuff in this update, and some of it you will have already merged through the ext4 tree which imported the dax-4.10-iomap-pmd topic branch from the XFS tree. There is also a new direct IO implementation that uses the iomap infrastructure. It's much simpler, faster, and has lower IO latency than the existing direct IO infrastructure. Summary: - DAX PMD faults via iomap infrastructure - Direct-io support in iomap infrastructure - removal of now-redundant XFS inode iolock, replaced with VFS i_rwsem - synchronisation with fixes and changes in userspace libxfs code - extent tree lookup helpers - lots of little corruption detection improvements to verifiers - optimised CRC calculations - faster buffer cache lookups - deprecation of barrier/nobarrier mount options - we always use REQ_FUA/REQ_FLUSH where appropriate for data integrity now - cleanups to speculative preallocation - miscellaneous minor bug fixes and cleanups" * tag 'xfs-for-linus-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (63 commits) xfs: nuke unused tracepoint definitions xfs: use GPF_NOFS when allocating btree cursors xfs: use xfs_vn_setattr_size to check on new size xfs: deprecate barrier/nobarrier mount option xfs: Always flush caches when integrity is required xfs: ignore leaf attr ichdr.count in verifier during log replay xfs: use rhashtable to track buffer cache xfs: optimise CRC updates xfs: make xfs btree stats less huge xfs: don't cap maximum dedupe request length xfs: don't allow di_size with high bit set xfs: error out if trying to add attrs and anextents > 0 xfs: don't crash if reading a directory results in an unexpected hole xfs: complain if we don't get nextents bmap records xfs: check for bogus values in btree block headers xfs: forbid AG btrees with level == 0 xfs: several xattr functions can be void xfs: handle cow fork in xfs_bmap_trace_exlist xfs: pass state not whichfork to trace_xfs_extlist xfs: Move AGI buffer type setting to xfs_read_agi ...
2016-12-15 05:35:31 +00:00
dio->submit.cookie))
io_schedule();
}
__set_current_state(TASK_RUNNING);
}
iomap: invalidate page caches should be after iomap_dio_complete() in direct write After XFS switching to iomap based DIO (commit acdda3aae146 ("xfs: use iomap_dio_rw")), I started to notice dio29/dio30 tests failures from LTP run on ppc64 hosts, and they can be reproduced on x86_64 hosts with 512B/1k block size XFS too. dio29 diotest3 -b 65536 -n 100 -i 1000 -o 1024000 dio30 diotest6 -b 65536 -n 100 -i 1000 -o 1024000 The failure message is like: bufcmp: offset 0: Expected: 0x62, got 0x0 diotest03 1 TPASS : Read with Direct IO, Write without diotest03 2 TFAIL : diotest3.c:142: comparsion failed; child=98 offset=1425408 diotest03 3 TFAIL : diotest3.c:194: Write Direct-child 98 failed Direct write wrote 0x62 but buffer read got zero. This is because, when doing direct write to a hole or preallocated file, we invalidate the page caches before converting the extent from unwritten state to normal state, which is done by iomap_dio_complete(), thus leave a window for other buffer reader to cache the unwritten state extent. Consider this case, with sub-page blocksize XFS, two processes are direct writing to different blocksize-aligned regions (say 512B) of the same preallocated file, and reading the region back via buffered I/O to compare contents. process A, region [0,512] process B, region [512,1024] xfs_file_write_iter xfs_file_aio_dio_write iomap_dio_rw iomap_apply invalidate_inode_pages2_range xfs_file_write_iter xfs_file_aio_dio_write iomap_dio_rw iomap_apply invalidate_inode_pages2_range iomap_dio_complete xfs_file_read_iter xfs_file_buffered_aio_read generic_file_read_iter do_generic_file_read <readahead fills pagecache with 0> iomap_dio_complete xfs_file_read_iter <read gets 0 from pagecache> Process A first invalidates page caches, at this point the underlying extent is still in unwritten state (iomap_dio_complete not called yet), and process B finishs direct write and populates page caches via readahead, which caches zeros in page for region A, then process A reads zeros from page cache, instead of the actual data. Fix it by invalidating page caches after converting unwritten extent to make sure we read content from disk after extent state changed, as what we did before switching to iomap based dio. Also introduce a new 'start' variable to save the original write offset (iomap_dio_complete() updates iocb->ki_pos), and a 'err' variable for invalidating caches result, cause we can't reuse 'ret' anymore. Signed-off-by: Eryu Guan <eguan@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2017-03-02 23:02:06 +00:00
ret = iomap_dio_complete(dio);
return ret;
out_free_dio:
kfree(dio);
return ret;
}
EXPORT_SYMBOL_GPL(iomap_dio_rw);
/* Swapfile activation */
#ifdef CONFIG_SWAP
struct iomap_swapfile_info {
struct iomap iomap; /* accumulated iomap */
struct swap_info_struct *sis;
uint64_t lowest_ppage; /* lowest physical addr seen (pages) */
uint64_t highest_ppage; /* highest physical addr seen (pages) */
unsigned long nr_pages; /* number of pages collected */
int nr_extents; /* extent count */
};
/*
* Collect physical extents for this swap file. Physical extents reported to
* the swap code must be trimmed to align to a page boundary. The logical
* offset within the file is irrelevant since the swapfile code maps logical
* page numbers of the swap device to the physical page-aligned extents.
*/
static int iomap_swapfile_add_extent(struct iomap_swapfile_info *isi)
{
struct iomap *iomap = &isi->iomap;
unsigned long nr_pages;
uint64_t first_ppage;
uint64_t first_ppage_reported;
uint64_t next_ppage;
int error;
/*
* Round the start up and the end down so that the physical
* extent aligns to a page boundary.
*/
first_ppage = ALIGN(iomap->addr, PAGE_SIZE) >> PAGE_SHIFT;
next_ppage = ALIGN_DOWN(iomap->addr + iomap->length, PAGE_SIZE) >>
PAGE_SHIFT;
/* Skip too-short physical extents. */
if (first_ppage >= next_ppage)
return 0;
nr_pages = next_ppage - first_ppage;
/*
* Calculate how much swap space we're adding; the first page contains
* the swap header and doesn't count. The mm still wants that first
* page fed to add_swap_extent, however.
*/
first_ppage_reported = first_ppage;
if (iomap->offset == 0)
first_ppage_reported++;
if (isi->lowest_ppage > first_ppage_reported)
isi->lowest_ppage = first_ppage_reported;
if (isi->highest_ppage < (next_ppage - 1))
isi->highest_ppage = next_ppage - 1;
/* Add extent, set up for the next call. */
error = add_swap_extent(isi->sis, isi->nr_pages, nr_pages, first_ppage);
if (error < 0)
return error;
isi->nr_extents += error;
isi->nr_pages += nr_pages;
return 0;
}
/*
* Accumulate iomaps for this swap file. We have to accumulate iomaps because
* swap only cares about contiguous page-aligned physical extents and makes no
* distinction between written and unwritten extents.
*/
static loff_t iomap_swapfile_activate_actor(struct inode *inode, loff_t pos,
loff_t count, void *data, struct iomap *iomap)
{
struct iomap_swapfile_info *isi = data;
int error;
switch (iomap->type) {
case IOMAP_MAPPED:
case IOMAP_UNWRITTEN:
/* Only real or unwritten extents. */
break;
case IOMAP_INLINE:
/* No inline data. */
pr_err("swapon: file is inline\n");
return -EINVAL;
default:
pr_err("swapon: file has unallocated extents\n");
return -EINVAL;
}
/* No uncommitted metadata or shared blocks. */
if (iomap->flags & IOMAP_F_DIRTY) {
pr_err("swapon: file is not committed\n");
return -EINVAL;
}
if (iomap->flags & IOMAP_F_SHARED) {
pr_err("swapon: file has shared extents\n");
return -EINVAL;
}
/* Only one bdev per swap file. */
if (iomap->bdev != isi->sis->bdev) {
pr_err("swapon: file is on multiple devices\n");
return -EINVAL;
}
if (isi->iomap.length == 0) {
/* No accumulated extent, so just store it. */
memcpy(&isi->iomap, iomap, sizeof(isi->iomap));
} else if (isi->iomap.addr + isi->iomap.length == iomap->addr) {
/* Append this to the accumulated extent. */
isi->iomap.length += iomap->length;
} else {
/* Otherwise, add the retained iomap and store this one. */
error = iomap_swapfile_add_extent(isi);
if (error)
return error;
memcpy(&isi->iomap, iomap, sizeof(isi->iomap));
}
return count;
}
/*
* Iterate a swap file's iomaps to construct physical extents that can be
* passed to the swapfile subsystem.
*/
int iomap_swapfile_activate(struct swap_info_struct *sis,
struct file *swap_file, sector_t *pagespan,
const struct iomap_ops *ops)
{
struct iomap_swapfile_info isi = {
.sis = sis,
.lowest_ppage = (sector_t)-1ULL,
};
struct address_space *mapping = swap_file->f_mapping;
struct inode *inode = mapping->host;
loff_t pos = 0;
loff_t len = ALIGN_DOWN(i_size_read(inode), PAGE_SIZE);
loff_t ret;
/*
* Persist all file mapping metadata so that we won't have any
* IOMAP_F_DIRTY iomaps.
*/
ret = vfs_fsync(swap_file, 1);
if (ret)
return ret;
while (len > 0) {
ret = iomap_apply(inode, pos, len, IOMAP_REPORT,
ops, &isi, iomap_swapfile_activate_actor);
if (ret <= 0)
return ret;
pos += ret;
len -= ret;
}
if (isi.iomap.length) {
ret = iomap_swapfile_add_extent(&isi);
if (ret)
return ret;
}
*pagespan = 1 + isi.highest_ppage - isi.lowest_ppage;
sis->max = isi.nr_pages;
sis->pages = isi.nr_pages - 1;
sis->highest_bit = isi.nr_pages - 1;
return isi.nr_extents;
}
EXPORT_SYMBOL_GPL(iomap_swapfile_activate);
#endif /* CONFIG_SWAP */
static loff_t
iomap_bmap_actor(struct inode *inode, loff_t pos, loff_t length,
void *data, struct iomap *iomap)
{
sector_t *bno = data, addr;
if (iomap->type == IOMAP_MAPPED) {
addr = (pos - iomap->offset + iomap->addr) >> inode->i_blkbits;
if (addr > INT_MAX)
WARN(1, "would truncate bmap result\n");
else
*bno = addr;
}
return 0;
}
/* legacy ->bmap interface. 0 is the error return (!) */
sector_t
iomap_bmap(struct address_space *mapping, sector_t bno,
const struct iomap_ops *ops)
{
struct inode *inode = mapping->host;
loff_t pos = bno >> inode->i_blkbits;
unsigned blocksize = i_blocksize(inode);
if (filemap_write_and_wait(mapping))
return 0;
bno = 0;
iomap_apply(inode, pos, blocksize, 0, ops, &bno, iomap_bmap_actor);
return bno;
}
EXPORT_SYMBOL_GPL(iomap_bmap);