linux/drivers/net/ethernet/intel/igc/igc_defines.h

/* SPDX-License-Identifier: GPL-2.0 */
/* Copyright (c)  2018 Intel Corporation */

#ifndef _IGC_DEFINES_H_
#define _IGC_DEFINES_H_

#define IGC_CTRL_EXT_DRV_LOAD	0x10000000 /* Drv loaded bit for FW */

/* PCI Bus Info */
#define PCIE_DEVICE_CONTROL2		0x28
#define PCIE_DEVICE_CONTROL2_16ms	0x0005

/* Physical Func Reset Done Indication */
#define IGC_CTRL_EXT_LINK_MODE_MASK	0x00C00000

/* Number of 100 microseconds we wait for PCI Express master disable */
#define MASTER_DISABLE_TIMEOUT		800
/*Blocks new Master requests */
#define IGC_CTRL_GIO_MASTER_DISABLE	0x00000004
/* Status of Master requests. */
#define IGC_STATUS_GIO_MASTER_ENABLE	0x00080000

/* PCI Express Control */
#define IGC_GCR_CMPL_TMOUT_MASK		0x0000F000
#define IGC_GCR_CMPL_TMOUT_10ms		0x00001000
#define IGC_GCR_CMPL_TMOUT_RESEND	0x00010000
#define IGC_GCR_CAP_VER2		0x00040000

/* Receive Address
 * Number of high/low register pairs in the RAR. The RAR (Receive Address
 * Registers) holds the directed and multicast addresses that we monitor.
 * Technically, we have 16 spots.  However, we reserve one of these spots
 * (RAR[15]) for our directed address used by controllers with
 * manageability enabled, allowing us room for 15 multicast addresses.
 */
#define IGC_RAH_AV		0x80000000 /* Receive descriptor valid */
#define IGC_RAH_POOL_1		0x00040000
#define IGC_RAL_MAC_ADDR_LEN	4
#define IGC_RAH_MAC_ADDR_LEN	2

/* Error Codes */
#define IGC_SUCCESS			0
#define IGC_ERR_NVM			1
#define IGC_ERR_PHY			2
#define IGC_ERR_CONFIG			3
#define IGC_ERR_PARAM			4
#define IGC_ERR_MAC_INIT		5
#define IGC_ERR_RESET			9
#define IGC_ERR_MASTER_REQUESTS_PENDING	10
#define IGC_ERR_SWFW_SYNC		13

/* Device Control */
#define IGC_CTRL_RST		0x04000000  /* Global reset */

/* PBA constants */
#define IGC_PBA_34K		0x0022

/* SW Semaphore Register */
#define IGC_SWSM_SMBI		0x00000001 /* Driver Semaphore bit */
#define IGC_SWSM_SWESMBI	0x00000002 /* FW Semaphore bit */

/* SWFW_SYNC Definitions */
#define IGC_SWFW_EEP_SM		0x1
#define IGC_SWFW_PHY0_SM	0x2

/* NVM Control */
/* Number of milliseconds for NVM auto read done after MAC reset. */
#define AUTO_READ_DONE_TIMEOUT		10
#define IGC_EECD_AUTO_RD		0x00000200  /* NVM Auto Read done */
#define IGC_EECD_REQ		0x00000040 /* NVM Access Request */
#define IGC_EECD_GNT		0x00000080 /* NVM Access Grant */
/* NVM Addressing bits based on type 0=small, 1=large */
#define IGC_EECD_ADDR_BITS		0x00000400
#define IGC_NVM_GRANT_ATTEMPTS		1000 /* NVM # attempts to gain grant */
#define IGC_EECD_SIZE_EX_MASK		0x00007800  /* NVM Size */
#define IGC_EECD_SIZE_EX_SHIFT		11
#define IGC_EECD_FLUPD_I225		0x00800000 /* Update FLASH */
#define IGC_EECD_FLUDONE_I225		0x04000000 /* Update FLASH done*/
#define IGC_EECD_FLASH_DETECTED_I225	0x00080000 /* FLASH detected */
#define IGC_FLUDONE_ATTEMPTS		20000
#define IGC_EERD_EEWR_MAX_COUNT		512 /* buffered EEPROM words rw */

/* Offset to data in NVM read/write registers */
#define IGC_NVM_RW_REG_DATA	16
#define IGC_NVM_RW_REG_DONE	2    /* Offset to READ/WRITE done bit */
#define IGC_NVM_RW_REG_START	1    /* Start operation */
#define IGC_NVM_RW_ADDR_SHIFT	2    /* Shift to the address bits */
#define IGC_NVM_POLL_READ	0    /* Flag for polling for read complete */

/* NVM Word Offsets */
#define NVM_CHECKSUM_REG		0x003F

/* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
#define NVM_SUM				0xBABA

#define NVM_PBA_OFFSET_0		8
#define NVM_PBA_OFFSET_1		9
#define NVM_RESERVED_WORD		0xFFFF
#define NVM_PBA_PTR_GUARD		0xFAFA
#define NVM_WORD_SIZE_BASE_SHIFT	6

/* Collision related configuration parameters */
#define IGC_COLLISION_THRESHOLD		15
#define IGC_CT_SHIFT			4
#define IGC_COLLISION_DISTANCE		63
#define IGC_COLD_SHIFT			12

/* Device Status */
#define IGC_STATUS_FD		0x00000001      /* Full duplex.0=half,1=full */
#define IGC_STATUS_LU		0x00000002      /* Link up.0=no,1=link */
#define IGC_STATUS_FUNC_MASK	0x0000000C      /* PCI Function Mask */
#define IGC_STATUS_FUNC_SHIFT	2
#define IGC_STATUS_FUNC_1	0x00000004      /* Function 1 */
#define IGC_STATUS_TXOFF	0x00000010      /* transmission paused */
#define IGC_STATUS_SPEED_100	0x00000040      /* Speed 100Mb/s */
#define IGC_STATUS_SPEED_1000	0x00000080      /* Speed 1000Mb/s */
#define IGC_STATUS_SPEED_2500	0x00400000	/* Speed 2.5Gb/s */

#define SPEED_10		10
#define SPEED_100		100
#define SPEED_1000		1000
#define SPEED_2500		2500
#define HALF_DUPLEX		1
#define FULL_DUPLEX		2

/* Interrupt Cause Read */
#define IGC_ICR_TXDW		BIT(0)	/* Transmit desc written back */
#define IGC_ICR_TXQE		BIT(1)	/* Transmit Queue empty */
#define IGC_ICR_LSC		BIT(2)	/* Link Status Change */
#define IGC_ICR_RXSEQ		BIT(3)	/* Rx sequence error */
#define IGC_ICR_RXDMT0		BIT(4)	/* Rx desc min. threshold (0) */
#define IGC_ICR_RXO		BIT(6)	/* Rx overrun */
#define IGC_ICR_RXT0		BIT(7)	/* Rx timer intr (ring 0) */
#define IGC_ICR_DRSTA		BIT(30)	/* Device Reset Asserted */

/* If this bit asserted, the driver should claim the interrupt */
#define IGC_ICR_INT_ASSERTED	BIT(31)

#define IGC_ICS_RXT0		IGC_ICR_RXT0 /* Rx timer intr */

#define IMS_ENABLE_MASK ( \
	IGC_IMS_RXT0   |    \
	IGC_IMS_TXDW   |    \
	IGC_IMS_RXDMT0 |    \
	IGC_IMS_RXSEQ  |    \
	IGC_IMS_LSC)

/* Interrupt Mask Set */
#define IGC_IMS_TXDW		IGC_ICR_TXDW	/* Tx desc written back */
#define IGC_IMS_RXSEQ		IGC_ICR_RXSEQ	/* Rx sequence error */
#define IGC_IMS_LSC		IGC_ICR_LSC	/* Link Status Change */
#define IGC_IMS_DOUTSYNC	IGC_ICR_DOUTSYNC /* NIC DMA out of sync */
#define IGC_IMS_DRSTA		IGC_ICR_DRSTA	/* Device Reset Asserted */
#define IGC_IMS_RXT0		IGC_ICR_RXT0	/* Rx timer intr */
#define IGC_IMS_RXDMT0		IGC_ICR_RXDMT0	/* Rx desc min. threshold */

#define IGC_QVECTOR_MASK	0x7FFC		/* Q-vector mask */
#define IGC_ITR_VAL_MASK	0x04		/* ITR value mask */

#define IGC_ICR_DOUTSYNC	0x10000000 /* NIC DMA out of sync */
#define IGC_EITR_CNT_IGNR	0x80000000 /* Don't reset counters on write */
#define IGC_IVAR_VALID		0x80
#define IGC_GPIE_NSICR		0x00000001
#define IGC_GPIE_MSIX_MODE	0x00000010
#define IGC_GPIE_EIAME		0x40000000
#define IGC_GPIE_PBA		0x80000000

/* Transmit Descriptor bit definitions */
#define IGC_TXD_DTYP_D		0x00100000 /* Data Descriptor */
#define IGC_TXD_DTYP_C		0x00000000 /* Context Descriptor */
#define IGC_TXD_POPTS_IXSM	0x01       /* Insert IP checksum */
#define IGC_TXD_POPTS_TXSM	0x02       /* Insert TCP/UDP checksum */
#define IGC_TXD_CMD_EOP		0x01000000 /* End of Packet */
#define IGC_TXD_CMD_IFCS	0x02000000 /* Insert FCS (Ethernet CRC) */
#define IGC_TXD_CMD_IC		0x04000000 /* Insert Checksum */
#define IGC_TXD_CMD_RS		0x08000000 /* Report Status */
#define IGC_TXD_CMD_RPS		0x10000000 /* Report Packet Sent */
#define IGC_TXD_CMD_DEXT	0x20000000 /* Desc extension (0 = legacy) */
#define IGC_TXD_CMD_VLE		0x40000000 /* Add VLAN tag */
#define IGC_TXD_CMD_IDE		0x80000000 /* Enable Tidv register */
#define IGC_TXD_STAT_DD		0x00000001 /* Descriptor Done */
#define IGC_TXD_STAT_EC		0x00000002 /* Excess Collisions */
#define IGC_TXD_STAT_LC		0x00000004 /* Late Collisions */
#define IGC_TXD_STAT_TU		0x00000008 /* Transmit underrun */
#define IGC_TXD_CMD_TCP		0x01000000 /* TCP packet */
#define IGC_TXD_CMD_IP		0x02000000 /* IP packet */
#define IGC_TXD_CMD_TSE		0x04000000 /* TCP Seg enable */
#define IGC_TXD_STAT_TC		0x00000004 /* Tx Underrun */
#define IGC_TXD_EXTCMD_TSTAMP	0x00000010 /* IEEE1588 Timestamp packet */

/* Transmit Control */
#define IGC_TCTL_EN		0x00000002 /* enable Tx */
#define IGC_TCTL_PSP		0x00000008 /* pad short packets */
#define IGC_TCTL_CT		0x00000ff0 /* collision threshold */
#define IGC_TCTL_COLD		0x003ff000 /* collision distance */
#define IGC_TCTL_RTLC		0x01000000 /* Re-transmit on late collision */
#define IGC_TCTL_MULR		0x10000000 /* Multiple request support */

#define IGC_CT_SHIFT			4
#define IGC_COLLISION_THRESHOLD		15

/* Flow Control Constants */
#define FLOW_CONTROL_ADDRESS_LOW	0x00C28001
#define FLOW_CONTROL_ADDRESS_HIGH	0x00000100
#define FLOW_CONTROL_TYPE		0x8808
/* Enable XON frame transmission */
#define IGC_FCRTL_XONE			0x80000000

/* Management Control */
#define IGC_MANC_RCV_TCO_EN	0x00020000 /* Receive TCO Packets Enabled */

/* Receive Control */
#define IGC_RCTL_RST		0x00000001 /* Software reset */
#define IGC_RCTL_EN		0x00000002 /* enable */
#define IGC_RCTL_SBP		0x00000004 /* store bad packet */
#define IGC_RCTL_UPE		0x00000008 /* unicast promisc enable */
#define IGC_RCTL_MPE		0x00000010 /* multicast promisc enable */
#define IGC_RCTL_LPE		0x00000020 /* long packet enable */
#define IGC_RCTL_LBM_MAC	0x00000040 /* MAC loopback mode */
#define IGC_RCTL_LBM_TCVR	0x000000C0 /* tcvr loopback mode */

#define IGC_RCTL_RDMTS_HALF	0x00000000 /* Rx desc min thresh size */
#define IGC_RCTL_BAM		0x00008000 /* broadcast enable */

/* Receive Descriptor bit definitions */
#define IGC_RXD_STAT_EOP	0x02    /* End of Packet */

#define IGC_RXDEXT_STATERR_CE		0x01000000
#define IGC_RXDEXT_STATERR_SE		0x02000000
#define IGC_RXDEXT_STATERR_SEQ		0x04000000
#define IGC_RXDEXT_STATERR_CXE		0x10000000
#define IGC_RXDEXT_STATERR_TCPE		0x20000000
#define IGC_RXDEXT_STATERR_IPE		0x40000000
#define IGC_RXDEXT_STATERR_RXE		0x80000000

/* Same mask, but for extended and packet split descriptors */
#define IGC_RXDEXT_ERR_FRAME_ERR_MASK ( \
	IGC_RXDEXT_STATERR_CE  |	\
	IGC_RXDEXT_STATERR_SE  |	\
	IGC_RXDEXT_STATERR_SEQ |	\
	IGC_RXDEXT_STATERR_CXE |	\
	IGC_RXDEXT_STATERR_RXE)

/* Header split receive */
#define IGC_RFCTL_IPV6_EX_DIS	0x00010000
#define IGC_RFCTL_LEF		0x00040000

#define IGC_RCTL_SZ_256		0x00030000 /* Rx buffer size 256 */

#define IGC_RCTL_MO_SHIFT	12 /* multicast offset shift */
#define IGC_RCTL_CFIEN		0x00080000 /* canonical form enable */
#define IGC_RCTL_DPF		0x00400000 /* discard pause frames */
#define IGC_RCTL_PMCF		0x00800000 /* pass MAC control frames */
#define IGC_RCTL_SECRC		0x04000000 /* Strip Ethernet CRC */

#define I225_RXPBSIZE_DEFAULT	0x000000A2 /* RXPBSIZE default */
#define I225_TXPBSIZE_DEFAULT	0x04000014 /* TXPBSIZE default */

#define IGC_N0_QUEUE -1

#endif /* _IGC_DEFINES_H_ */