linux/drivers/net/wireless/realtek/rtw88/ps.c

132 lines
2.5 KiB
C
Raw Normal View History

rtw88: new Realtek 802.11ac driver This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-26 12:17:37 +00:00
// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
/* Copyright(c) 2018-2019 Realtek Corporation
*/
#include "main.h"
#include "fw.h"
#include "ps.h"
#include "mac.h"
rtw88: add BT co-existence support Both RTL8822BE/RTL8822CE are WiFi + BT combo chips. Since WiFi and BT use 2.4GHz to transmit, it is important to make sure they run concurrently without interfering each other. To achieve this, WiFi driver requires a mechanism to collaborate with BT, whether they share the antenna(s) or not. The final decision made by the co-existence mechanism is to choose a proper strategy, or called "tdma/table", and inform either firmware or hardware of the strategy. To choose a strategy, co-existence mechanism needs to have enough information from WiFi and BT. BT information is provided through firmware C2H. The contents describe the current status of BT, such as if BT is connected or is idle, or the profile that is being used. WiFi information can be provided by WiFi itself. The WiFi driver will call various of "notify" functions each time the state of WiFi changed, such as WiFi is going to switch channel or is connected. Also WiFi driver can know if it shares antenna with BT by reading efuse content. Antenna configuration of the module will finally get a different strategy. Upon receiving any information from WiFi or BT, the WiFi driver will run the co-existence mechanism immediately. It will set the RF antenna configuration according to the strategy through the TDMA H2C to firmware and a hardware table. Based on the tdma/table, WiFi + BT should work with each other, and having a better user experience. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-07-31 12:22:47 +00:00
#include "coex.h"
rtw88: new Realtek 802.11ac driver This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-26 12:17:37 +00:00
#include "debug.h"
static int rtw_ips_pwr_up(struct rtw_dev *rtwdev)
{
int ret;
ret = rtw_core_start(rtwdev);
if (ret)
rtw_err(rtwdev, "leave idle state failed\n");
rtw_set_channel(rtwdev);
clear_bit(RTW_FLAG_INACTIVE_PS, rtwdev->flags);
rtw88: new Realtek 802.11ac driver This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-26 12:17:37 +00:00
return ret;
}
int rtw_enter_ips(struct rtw_dev *rtwdev)
{
set_bit(RTW_FLAG_INACTIVE_PS, rtwdev->flags);
rtw88: new Realtek 802.11ac driver This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-26 12:17:37 +00:00
rtw88: add BT co-existence support Both RTL8822BE/RTL8822CE are WiFi + BT combo chips. Since WiFi and BT use 2.4GHz to transmit, it is important to make sure they run concurrently without interfering each other. To achieve this, WiFi driver requires a mechanism to collaborate with BT, whether they share the antenna(s) or not. The final decision made by the co-existence mechanism is to choose a proper strategy, or called "tdma/table", and inform either firmware or hardware of the strategy. To choose a strategy, co-existence mechanism needs to have enough information from WiFi and BT. BT information is provided through firmware C2H. The contents describe the current status of BT, such as if BT is connected or is idle, or the profile that is being used. WiFi information can be provided by WiFi itself. The WiFi driver will call various of "notify" functions each time the state of WiFi changed, such as WiFi is going to switch channel or is connected. Also WiFi driver can know if it shares antenna with BT by reading efuse content. Antenna configuration of the module will finally get a different strategy. Upon receiving any information from WiFi or BT, the WiFi driver will run the co-existence mechanism immediately. It will set the RF antenna configuration according to the strategy through the TDMA H2C to firmware and a hardware table. Based on the tdma/table, WiFi + BT should work with each other, and having a better user experience. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-07-31 12:22:47 +00:00
rtw_coex_ips_notify(rtwdev, COEX_IPS_ENTER);
rtw88: new Realtek 802.11ac driver This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-26 12:17:37 +00:00
rtw_core_stop(rtwdev);
return 0;
}
static void rtw_restore_port_cfg_iter(void *data, u8 *mac,
struct ieee80211_vif *vif)
{
struct rtw_dev *rtwdev = data;
struct rtw_vif *rtwvif = (struct rtw_vif *)vif->drv_priv;
u32 config = ~0;
rtw_vif_port_config(rtwdev, rtwvif, config);
}
int rtw_leave_ips(struct rtw_dev *rtwdev)
{
int ret;
ret = rtw_ips_pwr_up(rtwdev);
if (ret) {
rtw_err(rtwdev, "failed to leave ips state\n");
return ret;
}
rtw_iterate_vifs_atomic(rtwdev, rtw_restore_port_cfg_iter, rtwdev);
rtw88: add BT co-existence support Both RTL8822BE/RTL8822CE are WiFi + BT combo chips. Since WiFi and BT use 2.4GHz to transmit, it is important to make sure they run concurrently without interfering each other. To achieve this, WiFi driver requires a mechanism to collaborate with BT, whether they share the antenna(s) or not. The final decision made by the co-existence mechanism is to choose a proper strategy, or called "tdma/table", and inform either firmware or hardware of the strategy. To choose a strategy, co-existence mechanism needs to have enough information from WiFi and BT. BT information is provided through firmware C2H. The contents describe the current status of BT, such as if BT is connected or is idle, or the profile that is being used. WiFi information can be provided by WiFi itself. The WiFi driver will call various of "notify" functions each time the state of WiFi changed, such as WiFi is going to switch channel or is connected. Also WiFi driver can know if it shares antenna with BT by reading efuse content. Antenna configuration of the module will finally get a different strategy. Upon receiving any information from WiFi or BT, the WiFi driver will run the co-existence mechanism immediately. It will set the RF antenna configuration according to the strategy through the TDMA H2C to firmware and a hardware table. Based on the tdma/table, WiFi + BT should work with each other, and having a better user experience. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-07-31 12:22:47 +00:00
rtw_coex_ips_notify(rtwdev, COEX_IPS_LEAVE);
rtw88: new Realtek 802.11ac driver This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-26 12:17:37 +00:00
return 0;
}
static void rtw_leave_lps_core(struct rtw_dev *rtwdev)
{
struct rtw_lps_conf *conf = &rtwdev->lps_conf;
conf->state = RTW_ALL_ON;
conf->awake_interval = 1;
conf->rlbm = 0;
conf->smart_ps = 0;
rtw_fw_set_pwr_mode(rtwdev);
clear_bit(RTW_FLAG_LEISURE_PS, rtwdev->flags);
rtw88: add BT co-existence support Both RTL8822BE/RTL8822CE are WiFi + BT combo chips. Since WiFi and BT use 2.4GHz to transmit, it is important to make sure they run concurrently without interfering each other. To achieve this, WiFi driver requires a mechanism to collaborate with BT, whether they share the antenna(s) or not. The final decision made by the co-existence mechanism is to choose a proper strategy, or called "tdma/table", and inform either firmware or hardware of the strategy. To choose a strategy, co-existence mechanism needs to have enough information from WiFi and BT. BT information is provided through firmware C2H. The contents describe the current status of BT, such as if BT is connected or is idle, or the profile that is being used. WiFi information can be provided by WiFi itself. The WiFi driver will call various of "notify" functions each time the state of WiFi changed, such as WiFi is going to switch channel or is connected. Also WiFi driver can know if it shares antenna with BT by reading efuse content. Antenna configuration of the module will finally get a different strategy. Upon receiving any information from WiFi or BT, the WiFi driver will run the co-existence mechanism immediately. It will set the RF antenna configuration according to the strategy through the TDMA H2C to firmware and a hardware table. Based on the tdma/table, WiFi + BT should work with each other, and having a better user experience. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-07-31 12:22:47 +00:00
rtw_coex_lps_notify(rtwdev, COEX_LPS_DISABLE);
rtw88: new Realtek 802.11ac driver This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-26 12:17:37 +00:00
}
static void rtw_enter_lps_core(struct rtw_dev *rtwdev)
{
struct rtw_lps_conf *conf = &rtwdev->lps_conf;
conf->state = RTW_RF_OFF;
conf->awake_interval = 1;
conf->rlbm = 1;
conf->smart_ps = 2;
rtw88: add BT co-existence support Both RTL8822BE/RTL8822CE are WiFi + BT combo chips. Since WiFi and BT use 2.4GHz to transmit, it is important to make sure they run concurrently without interfering each other. To achieve this, WiFi driver requires a mechanism to collaborate with BT, whether they share the antenna(s) or not. The final decision made by the co-existence mechanism is to choose a proper strategy, or called "tdma/table", and inform either firmware or hardware of the strategy. To choose a strategy, co-existence mechanism needs to have enough information from WiFi and BT. BT information is provided through firmware C2H. The contents describe the current status of BT, such as if BT is connected or is idle, or the profile that is being used. WiFi information can be provided by WiFi itself. The WiFi driver will call various of "notify" functions each time the state of WiFi changed, such as WiFi is going to switch channel or is connected. Also WiFi driver can know if it shares antenna with BT by reading efuse content. Antenna configuration of the module will finally get a different strategy. Upon receiving any information from WiFi or BT, the WiFi driver will run the co-existence mechanism immediately. It will set the RF antenna configuration according to the strategy through the TDMA H2C to firmware and a hardware table. Based on the tdma/table, WiFi + BT should work with each other, and having a better user experience. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-07-31 12:22:47 +00:00
rtw_coex_lps_notify(rtwdev, COEX_LPS_ENABLE);
rtw88: new Realtek 802.11ac driver This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-26 12:17:37 +00:00
rtw_fw_set_pwr_mode(rtwdev);
set_bit(RTW_FLAG_LEISURE_PS, rtwdev->flags);
rtw88: new Realtek 802.11ac driver This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-26 12:17:37 +00:00
}
bool rtw_in_lps(struct rtw_dev *rtwdev)
{
return test_bit(RTW_FLAG_LEISURE_PS, rtwdev->flags);
rtw88: new Realtek 802.11ac driver This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-26 12:17:37 +00:00
}
void rtw_enter_lps(struct rtw_dev *rtwdev, struct rtw_vif *rtwvif)
{
struct rtw_lps_conf *conf = &rtwdev->lps_conf;
if (WARN_ON(!rtwvif))
return;
if (rtwvif->in_lps)
return;
conf->mode = RTW_MODE_LPS;
conf->rtwvif = rtwvif;
rtwvif->in_lps = true;
rtw_enter_lps_core(rtwdev);
}
void rtw_leave_lps(struct rtw_dev *rtwdev, struct rtw_vif *rtwvif)
{
struct rtw_lps_conf *conf = &rtwdev->lps_conf;
if (WARN_ON(!rtwvif))
return;
if (!rtwvif->in_lps)
return;
conf->mode = RTW_MODE_ACTIVE;
conf->rtwvif = rtwvif;
rtwvif->in_lps = false;
rtw_leave_lps_core(rtwdev);
}