leandrof/linux
1
0
Fork 0
forked from Minki/linux
Code Issues Pull Requests Packages Projects Releases Wiki Activity
37b68e6ded
linux/net/8021q/Kconfig

41 lines
1.2 KiB
Plaintext
Raw Normal View History

[NET]: move config options out to individual protocols Move the protocol specific config options out to the specific protocols. With this change net/Kconfig now starts to become readable and serve as a good basis for further re-structuring. The menu structure is left almost intact, except that indention is fixed in most cases. Most visible are the INET changes where several "depends on INET" are replaced with a single ifdef INET / endif pair. Several new files were created to accomplish this change - they are small but serve the purpose that config options are now distributed out where they belongs. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-07-12 04:13:56 +00:00
#
# Configuration for 802.1Q VLAN support
#
config VLAN_8021Q
net: vlan: add 802.1ad support Add support for 802.1ad VLAN devices. This mainly consists of checking for ETH_P_8021AD in addition to ETH_P_8021Q in a couple of places and check offloading capabilities based on the used protocol. Configuration is done using "ip link": # ip link add link eth0 eth0.1000 \ type vlan proto 802.1ad id 1000 # ip link add link eth0.1000 eth0.1000.1000 \ type vlan proto 802.1q id 1000 52:54:00:12:34:56 > 92:b1:54:28:e4:8c, ethertype 802.1Q (0x8100), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 20.1.0.2 > 20.1.0.1: ICMP echo request, id 3003, seq 8, length 64 92:b1:54:28:e4:8c > 52:54:00:12:34:56, ethertype 802.1Q-QinQ (0x88a8), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 47944, offset 0, flags [none], proto ICMP (1), length 84) 20.1.0.1 > 20.1.0.2: ICMP echo reply, id 3003, seq 8, length 64 Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 02:04:31 +00:00
tristate "802.1Q/802.1ad VLAN Support"
[NET]: move config options out to individual protocols Move the protocol specific config options out to the specific protocols. With this change net/Kconfig now starts to become readable and serve as a good basis for further re-structuring. The menu structure is left almost intact, except that indention is fixed in most cases. Most visible are the INET changes where several "depends on INET" are replaced with a single ifdef INET / endif pair. Several new files were created to accomplish this change - they are small but serve the purpose that config options are now distributed out where they belongs. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-07-12 04:13:56 +00:00
---help---
Select this and you will be able to create 802.1Q VLAN interfaces
8021q: update description Replace deprecated 'vconfig' tool with 'ip' from 'iproute2'. Add some beautifications like replacing 'ethernet' with 'Ethernet' and removing unneeded spaces. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-20 09:49:39 +00:00
on your Ethernet interfaces. 802.1Q VLAN supports almost
everything a regular Ethernet interface does, including
firewalling, bridging, and of course IP traffic. You will need
the 'ip' utility in order to effectively use VLANs.
See the VLAN web page for more information:
[NET]: move config options out to individual protocols Move the protocol specific config options out to the specific protocols. With this change net/Kconfig now starts to become readable and serve as a good basis for further re-structuring. The menu structure is left almost intact, except that indention is fixed in most cases. Most visible are the INET changes where several "depends on INET" are replaced with a single ifdef INET / endif pair. Several new files were created to accomplish this change - they are small but serve the purpose that config options are now distributed out where they belongs. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-07-12 04:13:56 +00:00
<http://www.candelatech.com/~greear/vlan.html>
To compile this code as a module, choose M here: the module
will be called 8021q.
If unsure, say N.
vlan: Add GVRP support Add GVRP support for dynamically registering VLANs with switches. By default GVRP is disabled because we only support the applicant-only participant model, which means it should not be enabled on vlans that are members of a bridge. Since there is currently no way to cleanly determine that, the user is responsible for enabling it. The code is pretty small and low impact, its wrapped in a config option though because it depends on the GARP implementation and the STP core. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-06 04:26:57 +00:00
config VLAN_8021Q_GVRP
bool "GVRP (GARP VLAN Registration Protocol) support"
depends on VLAN_8021Q
select GARP
help
Select this to enable GVRP end-system support. GVRP is used for
automatic propagation of registered VLANs to switches.
If unsure, say N.
net/8021q: Implement Multiple VLAN Registration Protocol (MVRP) Initial implementation of the Multiple VLAN Registration Protocol (MVRP) from IEEE 802.1Q-2011, based on the existing implementation of the GARP VLAN Registration Protocol (GVRP). Signed-off-by: David Ward <david.ward@ll.mit.edu> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08 17:17:07 +00:00
config VLAN_8021Q_MVRP
bool "MVRP (Multiple VLAN Registration Protocol) support"
depends on VLAN_8021Q
select MRP
help
Select this to enable MVRP end-system support. MVRP is used for
automatic propagation of registered VLANs to switches; it
supersedes GVRP and is not backwards-compatible.
If unsure, say N.
Reference in New Issue Copy Permalink