linux/drivers/net/can/dev/bittiming.c

// SPDX-License-Identifier: GPL-2.0-only
/* Copyright (C) 2005 Marc Kleine-Budde, Pengutronix
 * Copyright (C) 2006 Andrey Volkov, Varma Electronics
 * Copyright (C) 2008-2009 Wolfgang Grandegger <wg@grandegger.com>
 */

#include <linux/units.h>
#include <linux/can/dev.h>

#ifdef CONFIG_CAN_CALC_BITTIMING
#define CAN_CALC_MAX_ERROR 50 /* in one-tenth of a percent */

/* Bit-timing calculation derived from:
 *
 * Code based on LinCAN sources and H8S2638 project
 * Copyright 2004-2006 Pavel Pisa - DCE FELK CVUT cz
 * Copyright 2005      Stanislav Marek
 * email: pisa@cmp.felk.cvut.cz
 *
 * Calculates proper bit-timing parameters for a specified bit-rate
 * and sample-point, which can then be used to set the bit-timing
 * registers of the CAN controller. You can find more information
 * in the header file linux/can/netlink.h.
 */
static int
can_update_sample_point(const struct can_bittiming_const *btc,
			unsigned int sample_point_nominal, unsigned int tseg,
			unsigned int *tseg1_ptr, unsigned int *tseg2_ptr,
			unsigned int *sample_point_error_ptr)
{
	unsigned int sample_point_error, best_sample_point_error = UINT_MAX;
	unsigned int sample_point, best_sample_point = 0;
	unsigned int tseg1, tseg2;
	int i;

	for (i = 0; i <= 1; i++) {
		tseg2 = tseg + CAN_SYNC_SEG -
			(sample_point_nominal * (tseg + CAN_SYNC_SEG)) /
			1000 - i;
		tseg2 = clamp(tseg2, btc->tseg2_min, btc->tseg2_max);
		tseg1 = tseg - tseg2;
		if (tseg1 > btc->tseg1_max) {
			tseg1 = btc->tseg1_max;
			tseg2 = tseg - tseg1;
		}

		sample_point = 1000 * (tseg + CAN_SYNC_SEG - tseg2) /
			(tseg + CAN_SYNC_SEG);
		sample_point_error = abs(sample_point_nominal - sample_point);

		if (sample_point <= sample_point_nominal &&
		    sample_point_error < best_sample_point_error) {
			best_sample_point = sample_point;
			best_sample_point_error = sample_point_error;
			*tseg1_ptr = tseg1;
			*tseg2_ptr = tseg2;
		}
	}

	if (sample_point_error_ptr)
		*sample_point_error_ptr = best_sample_point_error;

	return best_sample_point;
}

int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt,
		       const struct can_bittiming_const *btc)
{
	struct can_priv *priv = netdev_priv(dev);
	unsigned int bitrate;			/* current bitrate */
	unsigned int bitrate_error;		/* difference between current and nominal value */
	unsigned int best_bitrate_error = UINT_MAX;
	unsigned int sample_point_error;	/* difference between current and nominal value */
	unsigned int best_sample_point_error = UINT_MAX;
	unsigned int sample_point_nominal;	/* nominal sample point */
	unsigned int best_tseg = 0;		/* current best value for tseg */
	unsigned int best_brp = 0;		/* current best value for brp */
	unsigned int brp, tsegall, tseg, tseg1 = 0, tseg2 = 0;
	u64 v64;

	/* Use CiA recommended sample points */
	if (bt->sample_point) {
		sample_point_nominal = bt->sample_point;
	} else {
		if (bt->bitrate > 800 * KILO /* BPS */)
			sample_point_nominal = 750;
		else if (bt->bitrate > 500 * KILO /* BPS */)
			sample_point_nominal = 800;
		else
			sample_point_nominal = 875;
	}

	/* tseg even = round down, odd = round up */
	for (tseg = (btc->tseg1_max + btc->tseg2_max) * 2 + 1;
	     tseg >= (btc->tseg1_min + btc->tseg2_min) * 2; tseg--) {
		tsegall = CAN_SYNC_SEG + tseg / 2;

		/* Compute all possible tseg choices (tseg=tseg1+tseg2) */
		brp = priv->clock.freq / (tsegall * bt->bitrate) + tseg % 2;

		/* choose brp step which is possible in system */
		brp = (brp / btc->brp_inc) * btc->brp_inc;
		if (brp < btc->brp_min || brp > btc->brp_max)
			continue;

		bitrate = priv->clock.freq / (brp * tsegall);
		bitrate_error = abs(bt->bitrate - bitrate);

		/* tseg brp biterror */
		if (bitrate_error > best_bitrate_error)
			continue;

		/* reset sample point error if we have a better bitrate */
		if (bitrate_error < best_bitrate_error)
			best_sample_point_error = UINT_MAX;

		can_update_sample_point(btc, sample_point_nominal, tseg / 2,
					&tseg1, &tseg2, &sample_point_error);
		if (sample_point_error > best_sample_point_error)
			continue;

		best_sample_point_error = sample_point_error;
		best_bitrate_error = bitrate_error;
		best_tseg = tseg / 2;
		best_brp = brp;

		if (bitrate_error == 0 && sample_point_error == 0)
			break;
	}

	if (best_bitrate_error) {
		/* Error in one-tenth of a percent */
		v64 = (u64)best_bitrate_error * 1000;
		do_div(v64, bt->bitrate);
		bitrate_error = (u32)v64;
		if (bitrate_error > CAN_CALC_MAX_ERROR) {
			netdev_err(dev,
				   "bitrate error %d.%d%% too high\n",
				   bitrate_error / 10, bitrate_error % 10);
			return -EDOM;
		}
		netdev_warn(dev, "bitrate error %d.%d%%\n",
			    bitrate_error / 10, bitrate_error % 10);
	}

	/* real sample point */
	bt->sample_point = can_update_sample_point(btc, sample_point_nominal,
						   best_tseg, &tseg1, &tseg2,
						   NULL);

	v64 = (u64)best_brp * 1000 * 1000 * 1000;
	do_div(v64, priv->clock.freq);
	bt->tq = (u32)v64;
	bt->prop_seg = tseg1 / 2;
	bt->phase_seg1 = tseg1 - bt->prop_seg;
	bt->phase_seg2 = tseg2;

	/* check for sjw user settings */
	if (!bt->sjw || !btc->sjw_max) {
		bt->sjw = 1;
	} else {
		/* bt->sjw is at least 1 -> sanitize upper bound to sjw_max */
		if (bt->sjw > btc->sjw_max)
			bt->sjw = btc->sjw_max;
		/* bt->sjw must not be higher than tseg2 */
		if (tseg2 < bt->sjw)
			bt->sjw = tseg2;
	}

	bt->brp = best_brp;

	/* real bitrate */
	bt->bitrate = priv->clock.freq /
		(bt->brp * (CAN_SYNC_SEG + tseg1 + tseg2));

	return 0;
}

void can_calc_tdco(struct can_tdc *tdc, const struct can_tdc_const *tdc_const,
		   const struct can_bittiming *dbt,
		   u32 *ctrlmode, u32 ctrlmode_supported)

{
	if (!tdc_const || !(ctrlmode_supported & CAN_CTRLMODE_TDC_AUTO))
		return;

	*ctrlmode &= ~CAN_CTRLMODE_TDC_MASK;

	/* As specified in ISO 11898-1 section 11.3.3 "Transmitter
	 * delay compensation" (TDC) is only applicable if data BRP is
	 * one or two.
	 */
	if (dbt->brp == 1 || dbt->brp == 2) {
		/* Sample point in clock periods */
		u32 sample_point_in_tc = (CAN_SYNC_SEG + dbt->prop_seg +
					  dbt->phase_seg1) * dbt->brp;

		if (sample_point_in_tc < tdc_const->tdco_min)
			return;
		tdc->tdco = min(sample_point_in_tc, tdc_const->tdco_max);
		*ctrlmode |= CAN_CTRLMODE_TDC_AUTO;
	}
}
#endif /* CONFIG_CAN_CALC_BITTIMING */

/* Checks the validity of the specified bit-timing parameters prop_seg,
 * phase_seg1, phase_seg2 and sjw and tries to determine the bitrate
 * prescaler value brp. You can find more information in the header
 * file linux/can/netlink.h.
 */
static int can_fixup_bittiming(struct net_device *dev, struct can_bittiming *bt,
			       const struct can_bittiming_const *btc)
{
	struct can_priv *priv = netdev_priv(dev);
	unsigned int tseg1, alltseg;
	u64 brp64;

	tseg1 = bt->prop_seg + bt->phase_seg1;
	if (!bt->sjw)
		bt->sjw = 1;
	if (bt->sjw > btc->sjw_max ||
	    tseg1 < btc->tseg1_min || tseg1 > btc->tseg1_max ||
	    bt->phase_seg2 < btc->tseg2_min || bt->phase_seg2 > btc->tseg2_max)
		return -ERANGE;

	brp64 = (u64)priv->clock.freq * (u64)bt->tq;
	if (btc->brp_inc > 1)
		do_div(brp64, btc->brp_inc);
	brp64 += 500000000UL - 1;
	do_div(brp64, 1000000000UL); /* the practicable BRP */
	if (btc->brp_inc > 1)
		brp64 *= btc->brp_inc;
	bt->brp = (u32)brp64;

	if (bt->brp < btc->brp_min || bt->brp > btc->brp_max)
		return -EINVAL;

	alltseg = bt->prop_seg + bt->phase_seg1 + bt->phase_seg2 + 1;
	bt->bitrate = priv->clock.freq / (bt->brp * alltseg);
	bt->sample_point = ((tseg1 + 1) * 1000) / alltseg;

	return 0;
}

/* Checks the validity of predefined bitrate settings */
static int
can_validate_bitrate(struct net_device *dev, struct can_bittiming *bt,
		     const u32 *bitrate_const,
		     const unsigned int bitrate_const_cnt)
{
	struct can_priv *priv = netdev_priv(dev);
	unsigned int i;

	for (i = 0; i < bitrate_const_cnt; i++) {
		if (bt->bitrate == bitrate_const[i])
			break;
	}

	if (i >= priv->bitrate_const_cnt)
		return -EINVAL;

	return 0;
}

int can_get_bittiming(struct net_device *dev, struct can_bittiming *bt,
		      const struct can_bittiming_const *btc,
		      const u32 *bitrate_const,
		      const unsigned int bitrate_const_cnt)
{
	int err;

	/* Depending on the given can_bittiming parameter structure the CAN
	 * timing parameters are calculated based on the provided bitrate OR
	 * alternatively the CAN timing parameters (tq, prop_seg, etc.) are
	 * provided directly which are then checked and fixed up.
	 */
	if (!bt->tq && bt->bitrate && btc)
		err = can_calc_bittiming(dev, bt, btc);
	else if (bt->tq && !bt->bitrate && btc)
		err = can_fixup_bittiming(dev, bt, btc);
	else if (!bt->tq && bt->bitrate && bitrate_const)
		err = can_validate_bitrate(dev, bt, bitrate_const,
					   bitrate_const_cnt);
	else
		err = -EINVAL;

	return err;
}