mirror of
https://github.com/torvalds/linux.git
synced 2024-11-15 00:21:59 +00:00
9d94ec9857
mpf_ops_write() function writes bitstream data to the FPGA by a smaller frames. Introduce mpf_spi_frame_write() function which is for writing a single data frame and use it in mpf_ops_write(). No functional changes intended. Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru> Acked-by: Conor Dooley <conor.dooley@microchip.com> Acked-by: Xu Yilun <yilun.xu@intel.com> Link: https://lore.kernel.org/r/20221230092922.18822-4-i.bornyakov@metrotek.ru Signed-off-by: Xu Yilun <yilun.xu@intel.com>
413 lines
9.7 KiB
C
413 lines
9.7 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Microchip Polarfire FPGA programming over slave SPI interface.
|
|
*/
|
|
|
|
#include <asm/unaligned.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/fpga/fpga-mgr.h>
|
|
#include <linux/iopoll.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/spi/spi.h>
|
|
|
|
#define MPF_SPI_ISC_ENABLE 0x0B
|
|
#define MPF_SPI_ISC_DISABLE 0x0C
|
|
#define MPF_SPI_READ_STATUS 0x00
|
|
#define MPF_SPI_READ_DATA 0x01
|
|
#define MPF_SPI_FRAME_INIT 0xAE
|
|
#define MPF_SPI_FRAME 0xEE
|
|
#define MPF_SPI_PRG_MODE 0x01
|
|
#define MPF_SPI_RELEASE 0x23
|
|
|
|
#define MPF_SPI_FRAME_SIZE 16
|
|
|
|
#define MPF_HEADER_SIZE_OFFSET 24
|
|
#define MPF_DATA_SIZE_OFFSET 55
|
|
|
|
#define MPF_LOOKUP_TABLE_RECORD_SIZE 9
|
|
#define MPF_LOOKUP_TABLE_BLOCK_ID_OFFSET 0
|
|
#define MPF_LOOKUP_TABLE_BLOCK_START_OFFSET 1
|
|
|
|
#define MPF_COMPONENTS_SIZE_ID 5
|
|
#define MPF_BITSTREAM_ID 8
|
|
|
|
#define MPF_BITS_PER_COMPONENT_SIZE 22
|
|
|
|
#define MPF_STATUS_POLL_TIMEOUT (2 * USEC_PER_SEC)
|
|
#define MPF_STATUS_BUSY BIT(0)
|
|
#define MPF_STATUS_READY BIT(1)
|
|
#define MPF_STATUS_SPI_VIOLATION BIT(2)
|
|
#define MPF_STATUS_SPI_ERROR BIT(3)
|
|
|
|
struct mpf_priv {
|
|
struct spi_device *spi;
|
|
bool program_mode;
|
|
u8 tx __aligned(ARCH_KMALLOC_MINALIGN);
|
|
u8 rx;
|
|
};
|
|
|
|
static int mpf_read_status(struct mpf_priv *priv)
|
|
{
|
|
/*
|
|
* HW status is returned on MISO in the first byte after CS went
|
|
* active. However, first reading can be inadequate, so we submit
|
|
* two identical SPI transfers and use result of the later one.
|
|
*/
|
|
struct spi_transfer xfers[2] = {
|
|
{
|
|
.tx_buf = &priv->tx,
|
|
.rx_buf = &priv->rx,
|
|
.len = 1,
|
|
.cs_change = 1,
|
|
}, {
|
|
.tx_buf = &priv->tx,
|
|
.rx_buf = &priv->rx,
|
|
.len = 1,
|
|
},
|
|
};
|
|
u8 status;
|
|
int ret;
|
|
|
|
priv->tx = MPF_SPI_READ_STATUS;
|
|
|
|
ret = spi_sync_transfer(priv->spi, xfers, 2);
|
|
if (ret)
|
|
return ret;
|
|
|
|
status = priv->rx;
|
|
|
|
if ((status & MPF_STATUS_SPI_VIOLATION) ||
|
|
(status & MPF_STATUS_SPI_ERROR))
|
|
return -EIO;
|
|
|
|
return status;
|
|
}
|
|
|
|
static enum fpga_mgr_states mpf_ops_state(struct fpga_manager *mgr)
|
|
{
|
|
struct mpf_priv *priv = mgr->priv;
|
|
bool program_mode;
|
|
int status;
|
|
|
|
program_mode = priv->program_mode;
|
|
status = mpf_read_status(priv);
|
|
|
|
if (!program_mode && !status)
|
|
return FPGA_MGR_STATE_OPERATING;
|
|
|
|
return FPGA_MGR_STATE_UNKNOWN;
|
|
}
|
|
|
|
static int mpf_ops_parse_header(struct fpga_manager *mgr,
|
|
struct fpga_image_info *info,
|
|
const char *buf, size_t count)
|
|
{
|
|
size_t component_size_byte_num, component_size_byte_off,
|
|
components_size_start, bitstream_start,
|
|
block_id_offset, block_start_offset;
|
|
u8 header_size, blocks_num, block_id;
|
|
u32 block_start, component_size;
|
|
u16 components_num, i;
|
|
|
|
if (!buf) {
|
|
dev_err(&mgr->dev, "Image buffer is not provided\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
header_size = *(buf + MPF_HEADER_SIZE_OFFSET);
|
|
if (header_size > count) {
|
|
info->header_size = header_size;
|
|
return -EAGAIN;
|
|
}
|
|
|
|
/*
|
|
* Go through look-up table to find out where actual bitstream starts
|
|
* and where sizes of components of the bitstream lies.
|
|
*/
|
|
blocks_num = *(buf + header_size - 1);
|
|
block_id_offset = header_size + MPF_LOOKUP_TABLE_BLOCK_ID_OFFSET;
|
|
block_start_offset = header_size + MPF_LOOKUP_TABLE_BLOCK_START_OFFSET;
|
|
|
|
header_size += blocks_num * MPF_LOOKUP_TABLE_RECORD_SIZE;
|
|
if (header_size > count) {
|
|
info->header_size = header_size;
|
|
return -EAGAIN;
|
|
}
|
|
|
|
components_size_start = 0;
|
|
bitstream_start = 0;
|
|
|
|
while (blocks_num--) {
|
|
block_id = *(buf + block_id_offset);
|
|
block_start = get_unaligned_le32(buf + block_start_offset);
|
|
|
|
switch (block_id) {
|
|
case MPF_BITSTREAM_ID:
|
|
bitstream_start = block_start;
|
|
info->header_size = block_start;
|
|
if (block_start > count)
|
|
return -EAGAIN;
|
|
|
|
break;
|
|
case MPF_COMPONENTS_SIZE_ID:
|
|
components_size_start = block_start;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
if (bitstream_start && components_size_start)
|
|
break;
|
|
|
|
block_id_offset += MPF_LOOKUP_TABLE_RECORD_SIZE;
|
|
block_start_offset += MPF_LOOKUP_TABLE_RECORD_SIZE;
|
|
}
|
|
|
|
if (!bitstream_start || !components_size_start) {
|
|
dev_err(&mgr->dev, "Failed to parse header look-up table\n");
|
|
return -EFAULT;
|
|
}
|
|
|
|
/*
|
|
* Parse bitstream size.
|
|
* Sizes of components of the bitstream are 22-bits long placed next
|
|
* to each other. Image header should be extended by now up to where
|
|
* actual bitstream starts, so no need for overflow check anymore.
|
|
*/
|
|
components_num = get_unaligned_le16(buf + MPF_DATA_SIZE_OFFSET);
|
|
|
|
for (i = 0; i < components_num; i++) {
|
|
component_size_byte_num =
|
|
(i * MPF_BITS_PER_COMPONENT_SIZE) / BITS_PER_BYTE;
|
|
component_size_byte_off =
|
|
(i * MPF_BITS_PER_COMPONENT_SIZE) % BITS_PER_BYTE;
|
|
|
|
component_size = get_unaligned_le32(buf +
|
|
components_size_start +
|
|
component_size_byte_num);
|
|
component_size >>= component_size_byte_off;
|
|
component_size &= GENMASK(MPF_BITS_PER_COMPONENT_SIZE - 1, 0);
|
|
|
|
info->data_size += component_size * MPF_SPI_FRAME_SIZE;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mpf_poll_status(struct mpf_priv *priv, u8 mask)
|
|
{
|
|
int ret, status;
|
|
|
|
/*
|
|
* Busy poll HW status. Polling stops if any of the following
|
|
* conditions are met:
|
|
* - timeout is reached
|
|
* - mpf_read_status() returns an error
|
|
* - busy bit is cleared AND mask bits are set
|
|
*/
|
|
ret = read_poll_timeout(mpf_read_status, status,
|
|
(status < 0) ||
|
|
((status & (MPF_STATUS_BUSY | mask)) == mask),
|
|
0, MPF_STATUS_POLL_TIMEOUT, false, priv);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return status;
|
|
}
|
|
|
|
static int mpf_spi_write(struct mpf_priv *priv, const void *buf, size_t buf_size)
|
|
{
|
|
int status = mpf_poll_status(priv, 0);
|
|
|
|
if (status < 0)
|
|
return status;
|
|
|
|
return spi_write_then_read(priv->spi, buf, buf_size, NULL, 0);
|
|
}
|
|
|
|
static int mpf_spi_write_then_read(struct mpf_priv *priv,
|
|
const void *txbuf, size_t txbuf_size,
|
|
void *rxbuf, size_t rxbuf_size)
|
|
{
|
|
const u8 read_command[] = { MPF_SPI_READ_DATA };
|
|
int ret;
|
|
|
|
ret = mpf_spi_write(priv, txbuf, txbuf_size);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = mpf_poll_status(priv, MPF_STATUS_READY);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return spi_write_then_read(priv->spi, read_command, sizeof(read_command),
|
|
rxbuf, rxbuf_size);
|
|
}
|
|
|
|
static int mpf_ops_write_init(struct fpga_manager *mgr,
|
|
struct fpga_image_info *info, const char *buf,
|
|
size_t count)
|
|
{
|
|
const u8 program_mode[] = { MPF_SPI_FRAME_INIT, MPF_SPI_PRG_MODE };
|
|
const u8 isc_en_command[] = { MPF_SPI_ISC_ENABLE };
|
|
struct mpf_priv *priv = mgr->priv;
|
|
struct device *dev = &mgr->dev;
|
|
u32 isc_ret = 0;
|
|
int ret;
|
|
|
|
if (info->flags & FPGA_MGR_PARTIAL_RECONFIG) {
|
|
dev_err(dev, "Partial reconfiguration is not supported\n");
|
|
return -EOPNOTSUPP;
|
|
}
|
|
|
|
ret = mpf_spi_write_then_read(priv, isc_en_command, sizeof(isc_en_command),
|
|
&isc_ret, sizeof(isc_ret));
|
|
if (ret || isc_ret) {
|
|
dev_err(dev, "Failed to enable ISC: spi_ret %d, isc_ret %u\n",
|
|
ret, isc_ret);
|
|
return -EFAULT;
|
|
}
|
|
|
|
ret = mpf_spi_write(priv, program_mode, sizeof(program_mode));
|
|
if (ret) {
|
|
dev_err(dev, "Failed to enter program mode: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
priv->program_mode = true;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mpf_spi_frame_write(struct mpf_priv *priv, const char *buf)
|
|
{
|
|
struct spi_transfer xfers[2] = {
|
|
{
|
|
.tx_buf = &priv->tx,
|
|
.len = 1,
|
|
}, {
|
|
.tx_buf = buf,
|
|
.len = MPF_SPI_FRAME_SIZE,
|
|
},
|
|
};
|
|
int ret;
|
|
|
|
ret = mpf_poll_status(priv, 0);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
priv->tx = MPF_SPI_FRAME;
|
|
|
|
return spi_sync_transfer(priv->spi, xfers, ARRAY_SIZE(xfers));
|
|
}
|
|
|
|
static int mpf_ops_write(struct fpga_manager *mgr, const char *buf, size_t count)
|
|
{
|
|
struct mpf_priv *priv = mgr->priv;
|
|
struct device *dev = &mgr->dev;
|
|
int ret, i;
|
|
|
|
if (count % MPF_SPI_FRAME_SIZE) {
|
|
dev_err(dev, "Bitstream size is not a multiple of %d\n",
|
|
MPF_SPI_FRAME_SIZE);
|
|
return -EINVAL;
|
|
}
|
|
|
|
for (i = 0; i < count / MPF_SPI_FRAME_SIZE; i++) {
|
|
ret = mpf_spi_frame_write(priv, buf + i * MPF_SPI_FRAME_SIZE);
|
|
if (ret) {
|
|
dev_err(dev, "Failed to write bitstream frame %d/%zu\n",
|
|
i, count / MPF_SPI_FRAME_SIZE);
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mpf_ops_write_complete(struct fpga_manager *mgr,
|
|
struct fpga_image_info *info)
|
|
{
|
|
const u8 isc_dis_command[] = { MPF_SPI_ISC_DISABLE };
|
|
const u8 release_command[] = { MPF_SPI_RELEASE };
|
|
struct mpf_priv *priv = mgr->priv;
|
|
struct device *dev = &mgr->dev;
|
|
int ret;
|
|
|
|
ret = mpf_spi_write(priv, isc_dis_command, sizeof(isc_dis_command));
|
|
if (ret) {
|
|
dev_err(dev, "Failed to disable ISC: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
usleep_range(1000, 2000);
|
|
|
|
ret = mpf_spi_write(priv, release_command, sizeof(release_command));
|
|
if (ret) {
|
|
dev_err(dev, "Failed to exit program mode: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
priv->program_mode = false;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct fpga_manager_ops mpf_ops = {
|
|
.state = mpf_ops_state,
|
|
.initial_header_size = 71,
|
|
.skip_header = true,
|
|
.parse_header = mpf_ops_parse_header,
|
|
.write_init = mpf_ops_write_init,
|
|
.write = mpf_ops_write,
|
|
.write_complete = mpf_ops_write_complete,
|
|
};
|
|
|
|
static int mpf_probe(struct spi_device *spi)
|
|
{
|
|
struct device *dev = &spi->dev;
|
|
struct fpga_manager *mgr;
|
|
struct mpf_priv *priv;
|
|
|
|
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
|
|
if (!priv)
|
|
return -ENOMEM;
|
|
|
|
priv->spi = spi;
|
|
|
|
mgr = devm_fpga_mgr_register(dev, "Microchip Polarfire SPI FPGA Manager",
|
|
&mpf_ops, priv);
|
|
|
|
return PTR_ERR_OR_ZERO(mgr);
|
|
}
|
|
|
|
static const struct spi_device_id mpf_spi_ids[] = {
|
|
{ .name = "mpf-spi-fpga-mgr", },
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(spi, mpf_spi_ids);
|
|
|
|
#if IS_ENABLED(CONFIG_OF)
|
|
static const struct of_device_id mpf_of_ids[] = {
|
|
{ .compatible = "microchip,mpf-spi-fpga-mgr" },
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(of, mpf_of_ids);
|
|
#endif /* IS_ENABLED(CONFIG_OF) */
|
|
|
|
static struct spi_driver mpf_driver = {
|
|
.probe = mpf_probe,
|
|
.id_table = mpf_spi_ids,
|
|
.driver = {
|
|
.name = "microchip_mpf_spi_fpga_mgr",
|
|
.of_match_table = of_match_ptr(mpf_of_ids),
|
|
},
|
|
};
|
|
|
|
module_spi_driver(mpf_driver);
|
|
|
|
MODULE_DESCRIPTION("Microchip Polarfire SPI FPGA Manager");
|
|
MODULE_AUTHOR("Ivan Bornyakov <i.bornyakov@metrotek.ru>");
|
|
MODULE_LICENSE("GPL");
|