mirror of
https://github.com/torvalds/linux.git
synced 2024-11-18 01:51:53 +00:00
4be1fa2b55
Not all source files which include 'fdomain.h' make use of 'fdomain_pm_ops' leaving them defined but unused. Mark it as __maybe_unused to tell the compiler this is not only acceptable, but expected. Fixes the following W=1 kernel build warning(s): In file included from drivers/scsi/pcmcia/fdomain_cs.c:16: drivers/scsi/fdomain.h:106:32: warning: ‘fdomain_pm_ops’ defined but not used [-Wunused-const-variable=] 106 | static const struct dev_pm_ops fdomain_pm_ops; | ^~~~~~~~~~~~~~ Link: https://lore.kernel.org/r/20200707140055.2956235-4-lee.jones@linaro.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
115 lines
5.1 KiB
C
115 lines
5.1 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
|
|
#define FDOMAIN_REGION_SIZE 0x10
|
|
#define FDOMAIN_BIOS_SIZE 0x2000
|
|
|
|
enum {
|
|
in_arbitration = 0x02,
|
|
in_selection = 0x04,
|
|
in_other = 0x08,
|
|
disconnect = 0x10,
|
|
aborted = 0x20,
|
|
sent_ident = 0x40,
|
|
};
|
|
|
|
/* (@) = not present on TMC1800, (#) = not present on TMC1800 and TMC18C50 */
|
|
#define REG_SCSI_DATA 0 /* R/W: SCSI Data (with ACK) */
|
|
#define REG_BSTAT 1 /* R: SCSI Bus Status */
|
|
#define BSTAT_BSY BIT(0) /* Busy */
|
|
#define BSTAT_MSG BIT(1) /* Message */
|
|
#define BSTAT_IO BIT(2) /* Input/Output */
|
|
#define BSTAT_CMD BIT(3) /* Command/Data */
|
|
#define BSTAT_REQ BIT(4) /* Request and Not Ack */
|
|
#define BSTAT_SEL BIT(5) /* Select */
|
|
#define BSTAT_ACK BIT(6) /* Acknowledge and Request */
|
|
#define BSTAT_ATN BIT(7) /* Attention */
|
|
#define REG_BCTL 1 /* W: SCSI Bus Control */
|
|
#define BCTL_RST BIT(0) /* Bus Reset */
|
|
#define BCTL_SEL BIT(1) /* Select */
|
|
#define BCTL_BSY BIT(2) /* Busy */
|
|
#define BCTL_ATN BIT(3) /* Attention */
|
|
#define BCTL_IO BIT(4) /* Input/Output */
|
|
#define BCTL_CMD BIT(5) /* Command/Data */
|
|
#define BCTL_MSG BIT(6) /* Message */
|
|
#define BCTL_BUSEN BIT(7) /* Enable bus drivers */
|
|
#define REG_ASTAT 2 /* R: Adapter Status 1 */
|
|
#define ASTAT_IRQ BIT(0) /* Interrupt active */
|
|
#define ASTAT_ARB BIT(1) /* Arbitration complete */
|
|
#define ASTAT_PARERR BIT(2) /* Parity error */
|
|
#define ASTAT_RST BIT(3) /* SCSI reset occurred */
|
|
#define ASTAT_FIFODIR BIT(4) /* FIFO direction */
|
|
#define ASTAT_FIFOEN BIT(5) /* FIFO enabled */
|
|
#define ASTAT_PAREN BIT(6) /* Parity enabled */
|
|
#define ASTAT_BUSEN BIT(7) /* Bus drivers enabled */
|
|
#define REG_ICTL 2 /* W: Interrupt Control */
|
|
#define ICTL_FIFO_MASK 0x0f /* FIFO threshold, 1/16 FIFO size */
|
|
#define ICTL_FIFO BIT(4) /* Int. on FIFO count */
|
|
#define ICTL_ARB BIT(5) /* Int. on Arbitration complete */
|
|
#define ICTL_SEL BIT(6) /* Int. on SCSI Select */
|
|
#define ICTL_REQ BIT(7) /* Int. on SCSI Request */
|
|
#define REG_FSTAT 3 /* R: Adapter Status 2 (FIFO) - (@) */
|
|
#define FSTAT_ONOTEMPTY BIT(0) /* Output FIFO not empty */
|
|
#define FSTAT_INOTEMPTY BIT(1) /* Input FIFO not empty */
|
|
#define FSTAT_NOTEMPTY BIT(2) /* Main FIFO not empty */
|
|
#define FSTAT_NOTFULL BIT(3) /* Main FIFO not full */
|
|
#define REG_MCTL 3 /* W: SCSI Data Mode Control */
|
|
#define MCTL_ACK_MASK 0x0f /* Acknowledge period */
|
|
#define MCTL_ACTDEASS BIT(4) /* Active deassert of REQ and ACK */
|
|
#define MCTL_TARGET BIT(5) /* Enable target mode */
|
|
#define MCTL_FASTSYNC BIT(6) /* Enable Fast Synchronous */
|
|
#define MCTL_SYNC BIT(7) /* Enable Synchronous */
|
|
#define REG_INTCOND 4 /* R: Interrupt Condition - (@) */
|
|
#define IRQ_FIFO BIT(1) /* FIFO interrupt */
|
|
#define IRQ_REQ BIT(2) /* SCSI Request interrupt */
|
|
#define IRQ_SEL BIT(3) /* SCSI Select interrupt */
|
|
#define IRQ_ARB BIT(4) /* SCSI Arbitration interrupt */
|
|
#define IRQ_RST BIT(5) /* SCSI Reset interrupt */
|
|
#define IRQ_FORCED BIT(6) /* Forced interrupt */
|
|
#define IRQ_TIMEOUT BIT(7) /* Bus timeout */
|
|
#define REG_ACTL 4 /* W: Adapter Control 1 */
|
|
#define ACTL_RESET BIT(0) /* Reset FIFO, parity, reset int. */
|
|
#define ACTL_FIRQ BIT(1) /* Set Forced interrupt */
|
|
#define ACTL_ARB BIT(2) /* Initiate Bus Arbitration */
|
|
#define ACTL_PAREN BIT(3) /* Enable SCSI Parity */
|
|
#define ACTL_IRQEN BIT(4) /* Enable interrupts */
|
|
#define ACTL_CLRFIRQ BIT(5) /* Clear Forced interrupt */
|
|
#define ACTL_FIFOWR BIT(6) /* FIFO Direction (1=write) */
|
|
#define ACTL_FIFOEN BIT(7) /* Enable FIFO */
|
|
#define REG_ID_LSB 5 /* R: ID Code (LSB) */
|
|
#define REG_ACTL2 5 /* Adapter Control 2 - (@) */
|
|
#define ACTL2_RAMOVRLY BIT(0) /* Enable RAM overlay */
|
|
#define ACTL2_SLEEP BIT(7) /* Sleep mode */
|
|
#define REG_ID_MSB 6 /* R: ID Code (MSB) */
|
|
#define REG_LOOPBACK 7 /* R/W: Loopback */
|
|
#define REG_SCSI_DATA_NOACK 8 /* R/W: SCSI Data (no ACK) */
|
|
#define REG_ASTAT3 9 /* R: Adapter Status 3 */
|
|
#define ASTAT3_ACTDEASS BIT(0) /* Active deassert enabled */
|
|
#define ASTAT3_RAMOVRLY BIT(1) /* RAM overlay enabled */
|
|
#define ASTAT3_TARGERR BIT(2) /* Target error */
|
|
#define ASTAT3_IRQEN BIT(3) /* Interrupts enabled */
|
|
#define ASTAT3_IRQMASK 0xf0 /* Enabled interrupts mask */
|
|
#define REG_CFG1 10 /* R: Configuration Register 1 */
|
|
#define CFG1_BUS BIT(0) /* 0 = ISA */
|
|
#define CFG1_IRQ_MASK 0x0e /* IRQ jumpers */
|
|
#define CFG1_IO_MASK 0x30 /* I/O base jumpers */
|
|
#define CFG1_BIOS_MASK 0xc0 /* BIOS base jumpers */
|
|
#define REG_CFG2 11 /* R/W: Configuration Register 2 (@) */
|
|
#define CFG2_ROMDIS BIT(0) /* ROM disabled */
|
|
#define CFG2_RAMDIS BIT(1) /* RAM disabled */
|
|
#define CFG2_IRQEDGE BIT(2) /* Edge-triggered interrupts */
|
|
#define CFG2_NOWS BIT(3) /* No wait states */
|
|
#define CFG2_32BIT BIT(7) /* 32-bit mode */
|
|
#define REG_FIFO 12 /* R/W: FIFO */
|
|
#define REG_FIFO_COUNT 14 /* R: FIFO Data Count */
|
|
|
|
#ifdef CONFIG_PM_SLEEP
|
|
static const struct dev_pm_ops __maybe_unused fdomain_pm_ops;
|
|
#define FDOMAIN_PM_OPS (&fdomain_pm_ops)
|
|
#else
|
|
#define FDOMAIN_PM_OPS NULL
|
|
#endif /* CONFIG_PM_SLEEP */
|
|
|
|
struct Scsi_Host *fdomain_create(int base, int irq, int this_id,
|
|
struct device *dev);
|
|
int fdomain_destroy(struct Scsi_Host *sh);
|