mirror of
https://github.com/torvalds/linux.git
synced 2024-11-16 17:12:06 +00:00
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
198 lines
7.9 KiB
Plaintext
198 lines
7.9 KiB
Plaintext
Please mail me (Jon Diekema, diekema_jon@si.com or diekema@cideas.com)
|
|
if you have questions, comments or corrections.
|
|
|
|
* EST SBC8260 Linux memory mapping rules
|
|
|
|
http://www.estc.com/
|
|
http://www.estc.com/products/boards/SBC8260-8240_ds.html
|
|
|
|
Initial conditions:
|
|
-------------------
|
|
|
|
Tasks that need to be perform by the boot ROM before control is
|
|
transferred to zImage (compressed Linux kernel):
|
|
|
|
- Define the IMMR to 0xf0000000
|
|
|
|
- Initialize the memory controller so that RAM is available at
|
|
physical address 0x00000000. On the SBC8260 is this 16M (64M)
|
|
SDRAM.
|
|
|
|
- The boot ROM should only clear the RAM that it is using.
|
|
|
|
The reason for doing this is to enhances the chances of a
|
|
successful post mortem on a Linux panic. One of the first
|
|
items to examine is the 16k (LOG_BUF_LEN) circular console
|
|
buffer called log_buf which is defined in kernel/printk.c.
|
|
|
|
- To enhance boot ROM performance, the I-cache can be enabled.
|
|
|
|
Date: Mon, 22 May 2000 14:21:10 -0700
|
|
From: Neil Russell <caret@c-side.com>
|
|
|
|
LiMon (LInux MONitor) runs with and starts Linux with MMU
|
|
off, I-cache enabled, D-cache disabled. The I-cache doesn't
|
|
need hints from the MMU to work correctly as the D-cache
|
|
does. No D-cache means no special code to handle devices in
|
|
the presence of cache (no snooping, etc). The use of the
|
|
I-cache means that the monitor can run acceptably fast
|
|
directly from ROM, rather than having to copy it to RAM.
|
|
|
|
- Build the board information structure (see
|
|
include/asm-ppc/est8260.h for its definition)
|
|
|
|
- The compressed Linux kernel (zImage) contains a bootstrap loader
|
|
that is position independent; you can load it into any RAM,
|
|
ROM or FLASH memory address >= 0x00500000 (above 5 MB), or
|
|
at its link address of 0x00400000 (4 MB).
|
|
|
|
Note: If zImage is loaded at its link address of 0x00400000 (4 MB),
|
|
then zImage will skip the step of moving itself to
|
|
its link address.
|
|
|
|
- Load R3 with the address of the board information structure
|
|
|
|
- Transfer control to zImage
|
|
|
|
- The Linux console port is SMC1, and the baud rate is controlled
|
|
from the bi_baudrate field of the board information structure.
|
|
On thing to keep in mind when picking the baud rate, is that
|
|
there is no flow control on the SMC ports. I would stick
|
|
with something safe and standard like 19200.
|
|
|
|
On the EST SBC8260, the SMC1 port is on the COM1 connector of
|
|
the board.
|
|
|
|
|
|
EST SBC8260 defaults:
|
|
---------------------
|
|
|
|
Chip
|
|
Memory Sel Bus Use
|
|
--------------------- --- --- ----------------------------------
|
|
0x00000000-0x03FFFFFF CS2 60x (16M or 64M)/64M SDRAM
|
|
0x04000000-0x04FFFFFF CS4 local 4M/16M SDRAM (soldered to the board)
|
|
0x21000000-0x21000000 CS7 60x 1B/64K Flash present detect (from the flash SIMM)
|
|
0x21000001-0x21000001 CS7 60x 1B/64K Switches (read) and LEDs (write)
|
|
0x22000000-0x2200FFFF CS5 60x 8K/64K EEPROM
|
|
0xFC000000-0xFCFFFFFF CS6 60x 2M/16M flash (8 bits wide, soldered to the board)
|
|
0xFE000000-0xFFFFFFFF CS0 60x 4M/16M flash (SIMM)
|
|
|
|
Notes:
|
|
------
|
|
|
|
- The chip selects can map 32K blocks and up (powers of 2)
|
|
|
|
- The SDRAM machine can handled up to 128Mbytes per chip select
|
|
|
|
- Linux uses the 60x bus memory (the SDRAM DIMM) for the
|
|
communications buffers.
|
|
|
|
- BATs can map 128K-256Mbytes each. There are four data BATs and
|
|
four instruction BATs. Generally the data and instruction BATs
|
|
are mapped the same.
|
|
|
|
- The IMMR must be set above the kernel virtual memory addresses,
|
|
which start at 0xC0000000. Otherwise, the kernel may crash as
|
|
soon as you start any threads or processes due to VM collisions
|
|
in the kernel or user process space.
|
|
|
|
|
|
Details from Dan Malek <dan_malek@mvista.com> on 10/29/1999:
|
|
|
|
The user application virtual space consumes the first 2 Gbytes
|
|
(0x00000000 to 0x7FFFFFFF). The kernel virtual text starts at
|
|
0xC0000000, with data following. There is a "protection hole"
|
|
between the end of kernel data and the start of the kernel
|
|
dynamically allocated space, but this space is still within
|
|
0xCxxxxxxx.
|
|
|
|
Obviously the kernel can't map any physical addresses 1:1 in
|
|
these ranges.
|
|
|
|
|
|
Details from Dan Malek <dan_malek@mvista.com> on 5/19/2000:
|
|
|
|
During the early kernel initialization, the kernel virtual
|
|
memory allocator is not operational. Prior to this KVM
|
|
initialization, we choose to map virtual to physical addresses
|
|
1:1. That is, the kernel virtual address exactly matches the
|
|
physical address on the bus. These mappings are typically done
|
|
in arch/ppc/kernel/head.S, or arch/ppc/mm/init.c. Only
|
|
absolutely necessary mappings should be done at this time, for
|
|
example board control registers or a serial uart. Normal device
|
|
driver initialization should map resources later when necessary.
|
|
|
|
Although platform dependent, and certainly the case for embedded
|
|
8xx, traditionally memory is mapped at physical address zero,
|
|
and I/O devices above physical address 0x80000000. The lowest
|
|
and highest (above 0xf0000000) I/O addresses are traditionally
|
|
used for devices or registers we need to map during kernel
|
|
initialization and prior to KVM operation. For this reason,
|
|
and since it followed prior PowerPC platform examples, I chose
|
|
to map the embedded 8xx kernel to the 0xc0000000 virtual address.
|
|
This way, we can enable the MMU to map the kernel for proper
|
|
operation, and still map a few windows before the KVM is operational.
|
|
|
|
On some systems, you could possibly run the kernel at the
|
|
0x80000000 or any other virtual address. It just depends upon
|
|
mapping that must be done prior to KVM operational. You can never
|
|
map devices or kernel spaces that overlap with the user virtual
|
|
space. This is why default IMMR mapping used by most BDM tools
|
|
won't work. They put the IMMR at something like 0x10000000 or
|
|
0x02000000 for example. You simply can't map these addresses early
|
|
in the kernel, and continue proper system operation.
|
|
|
|
The embedded 8xx/82xx kernel is mature enough that all you should
|
|
need to do is map the IMMR someplace at or above 0xf0000000 and it
|
|
should boot far enough to get serial console messages and KGDB
|
|
connected on any platform. There are lots of other subtle memory
|
|
management design features that you simply don't need to worry
|
|
about. If you are changing functions related to MMU initialization,
|
|
you are likely breaking things that are known to work and are
|
|
heading down a path of disaster and frustration. Your changes
|
|
should be to make the flexibility of the processor fit Linux,
|
|
not force arbitrary and non-workable memory mappings into Linux.
|
|
|
|
- You don't want to change KERNELLOAD or KERNELBASE, otherwise the
|
|
virtual memory and MMU code will get confused.
|
|
|
|
arch/ppc/Makefile:KERNELLOAD = 0xc0000000
|
|
|
|
include/asm-ppc/page.h:#define PAGE_OFFSET 0xc0000000
|
|
include/asm-ppc/page.h:#define KERNELBASE PAGE_OFFSET
|
|
|
|
- RAM is at physical address 0x00000000, and gets mapped to
|
|
virtual address 0xC0000000 for the kernel.
|
|
|
|
|
|
Physical addresses used by the Linux kernel:
|
|
--------------------------------------------
|
|
|
|
0x00000000-0x3FFFFFFF 1GB reserved for RAM
|
|
0xF0000000-0xF001FFFF 128K IMMR 64K used for dual port memory,
|
|
64K for 8260 registers
|
|
|
|
|
|
Logical addresses used by the Linux kernel:
|
|
-------------------------------------------
|
|
|
|
0xF0000000-0xFFFFFFFF 256M BAT0 (IMMR: dual port RAM, registers)
|
|
0xE0000000-0xEFFFFFFF 256M BAT1 (I/O space for custom boards)
|
|
0xC0000000-0xCFFFFFFF 256M BAT2 (RAM)
|
|
0xD0000000-0xDFFFFFFF 256M BAT3 (if RAM > 256MByte)
|
|
|
|
|
|
EST SBC8260 Linux mapping:
|
|
--------------------------
|
|
|
|
DBAT0, IBAT0, cache inhibited:
|
|
|
|
Chip
|
|
Memory Sel Use
|
|
--------------------- --- ---------------------------------
|
|
0xF0000000-0xF001FFFF n/a IMMR: dual port RAM, registers
|
|
|
|
DBAT1, IBAT1, cache inhibited:
|
|
|