mirror of
https://github.com/torvalds/linux.git
synced 2024-11-17 09:31:50 +00:00
f22978400e
Link: https://lore.kernel.org/r/212fd7961c134c5bd73d87cd818bcddc30270804.1583136624.git.mchehab+huawei@kernel.org Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
93 lines
3.4 KiB
ReStructuredText
93 lines
3.4 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0
|
|
|
|
===================
|
|
Adaptec dpti driver
|
|
===================
|
|
|
|
Redistribution and use in source form, with or without modification, are
|
|
permitted provided that redistributions of source code must retain the
|
|
above copyright notice, this list of conditions and the following disclaimer.
|
|
|
|
This software is provided ``as is`` by Adaptec and
|
|
any express or implied warranties, including, but not limited to, the
|
|
implied warranties of merchantability and fitness for a particular purpose,
|
|
are disclaimed. In no event shall Adaptec be
|
|
liable for any direct, indirect, incidental, special, exemplary or
|
|
consequential damages (including, but not limited to, procurement of
|
|
substitute goods or services; loss of use, data, or profits; or business
|
|
interruptions) however caused and on any theory of liability, whether in
|
|
contract, strict liability, or tort (including negligence or otherwise)
|
|
arising in any way out of the use of this driver software, even if advised
|
|
of the possibility of such damage.
|
|
|
|
This driver supports the Adaptec I2O RAID and DPT SmartRAID V I2O boards.
|
|
|
|
Credits
|
|
=======
|
|
|
|
The original linux driver was ported to Linux by Karen White while at
|
|
Dell Computer. It was ported from Bob Pasteur's (of DPT) original
|
|
non-Linux driver. Mark Salyzyn and Bob Pasteur consulted on the original
|
|
driver.
|
|
|
|
2.0 version of the driver by Deanna Bonds and Mark Salyzyn.
|
|
|
|
History
|
|
=======
|
|
|
|
The driver was originally ported to linux version 2.0.34
|
|
|
|
==== ==========================================================================
|
|
V2.0 Rewrite of driver. Re-architectured based on i2o subsystem.
|
|
This was the first full GPL version since the last version used
|
|
i2osig headers which were not GPL. Developer Testing version.
|
|
V2.1 Internal testing
|
|
V2.2 First released version
|
|
|
|
V2.3 Changes:
|
|
|
|
- Added Raptor Support
|
|
- Fixed bug causing system to hang under extreme load with
|
|
- management utilities running (removed GFP_DMA from kmalloc flags)
|
|
|
|
V2.4 First version ready to be submitted to be embedded in the kernel
|
|
|
|
Changes:
|
|
|
|
- Implemented suggestions from Alan Cox
|
|
- Added calculation of resid for sg layer
|
|
- Better error handling
|
|
- Added checking underflow conditions
|
|
- Added DATAPROTECT checking
|
|
- Changed error return codes
|
|
- Fixed pointer bug in bus reset routine
|
|
- Enabled hba reset from ioctls (allows a FW flash to reboot and use
|
|
the new FW without having to reboot)
|
|
- Changed proc output
|
|
==== ==========================================================================
|
|
|
|
TODO
|
|
====
|
|
- Add 64 bit Scatter Gather when compiled on 64 bit architectures
|
|
- Add sparse lun scanning
|
|
- Add code that checks if a device that had been taken offline is
|
|
now online (at the FW level) when test unit ready or inquiry
|
|
command from scsi-core
|
|
- Add proc read interface
|
|
- busrescan command
|
|
- rescan command
|
|
- Add code to rescan routine that notifies scsi-core about new devices
|
|
- Add support for C-PCI (hotplug stuff)
|
|
- Add ioctl passthru error recovery
|
|
|
|
Notes
|
|
=====
|
|
The DPT card optimizes the order of processing commands. Consequently,
|
|
a command may take up to 6 minutes to complete after it has been sent
|
|
to the board.
|
|
|
|
The files dpti_ioctl.h dptsig.h osd_defs.h osd_util.h sys_info.h are part of the
|
|
interface files for Adaptec's management routines. These define the structures used
|
|
in the ioctls. They are written to be portable. They are hard to read, but I need
|
|
to use them 'as is' or I can miss changes in the interface.
|