mirror of
https://github.com/torvalds/linux.git
synced 2024-11-15 00:21:59 +00:00
e35a4a4e13
* Replace the expert mode symbols with a single helper
* Fix misuses of of_match_ptr()
* Remove partid and partname debugfs files
* tests: Fix eraseblock read speed miscalculation for lower partition sizes
* TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
* spear_smi: use GFP_KERNEL
* mchp48l640: Add SPI ID table
* mchp23k256: Add SPI ID table
* blkdevs: Avoid soft lockups with some mtd/spi devices
* aspeed-smc: Improve probe resilience
Hyperbus changes:
* HBMC_AM654 should depend on ARCH_K3
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
* Fix misuses of of_match_node()
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI NOR core changes:
* Move vendor specific code out of the core into vendor drivers.
* Unify all function and object names in the vendor modules.
* Make setup() callback optional to improve readability.
* Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
* Dropped mtd/cortina,gemini-flash.txt
* Convert BCM47xx partitions to json-schema
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI7WJcACgkQJWrqGEe9
VoSzpAgAutzRv9TRUiXdBGGlJ851QaZ6ZUvT1bHKTQA+xZi+MZyNmc0cWNg3B70I
PnwyxNAmRkUQKwV5Vgy/sQrt42qZnPmr+8XMq+UiziPmgFdjiTdLqGcN619Hi12t
JqtoKL828R064LSEq5nWsJ2waoGT1nNtZK8kA2qe8ctvmH0YTThriVZUQR4/Befb
OGFheceLFycE/vkktPPr3As4603fMiyDOT7EA3Mtzgjohry0a0TqoakHCaHC/fYo
0/h+x+jJATPtgbWm1ZiV3cZ/Su00+rKuQOsiAWvM/pqDaijsVntBmtK0PRtums2Q
m8LCspuQYNnCINeQXqba9RxACpibDg==
=+6Zk
-----END PGP SIGNATURE-----
Merge tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
|
||
|---|---|---|
| .. | ||
| bcma_private.h | ||
| core.c | ||
| driver_chipcommon_b.c | ||
| driver_chipcommon_nflash.c | ||
| driver_chipcommon_pflash.c | ||
| driver_chipcommon_pmu.c | ||
| driver_chipcommon_sflash.c | ||
| driver_chipcommon.c | ||
| driver_gmac_cmn.c | ||
| driver_gpio.c | ||
| driver_mips.c | ||
| driver_pci_host.c | ||
| driver_pci.c | ||
| driver_pcie2.c | ||
| host_pci.c | ||
| host_soc.c | ||
| Kconfig | ||
| main.c | ||
| Makefile | ||
| README | ||
| scan.c | ||
| scan.h | ||
| sprom.c | ||
| TODO | ||
Broadcom introduced new bus as replacement for older SSB. It is based on AMBA, however from programming point of view there is nothing AMBA specific we use. Standard AMBA drivers are platform specific, have hardcoded addresses and use AMBA standard fields like CID and PID. In case of Broadcom's cards every device consists of: 1) Broadcom specific AMBA device. It is put on AMBA bus, but can not be treated as standard AMBA device. Reading it's CID or PID can cause machine lockup. 2) AMBA standard devices called ports or wrappers. They have CIDs (AMBA_CID) and PIDs (0x103BB369), but we do not use that info for anything. One of that devices is used for managing Broadcom specific core. Addresses of AMBA devices are not hardcoded in driver and have to be read from EPROM. In this situation we decided to introduce separated bus. It can contain up to 16 devices identified by Broadcom specific fields: manufacturer, id, revision and class.