mirror of
https://github.com/torvalds/linux.git
synced 2024-11-19 02:21:47 +00:00
ccae7af2bf
Move the tuners one level up, as the "common" directory will be used by drivers that are shared between more than one driver. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
105 lines
4.2 KiB
C
105 lines
4.2 KiB
C
/*
|
|
* Driver for Microtune MT2060 "Single chip dual conversion broadband tuner"
|
|
*
|
|
* Copyright (c) 2006 Olivier DANET <odanet@caramail.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
*
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.=
|
|
*/
|
|
|
|
#ifndef MT2060_PRIV_H
|
|
#define MT2060_PRIV_H
|
|
|
|
// Uncomment the #define below to enable spurs checking. The results where quite unconvincing.
|
|
// #define MT2060_SPURCHECK
|
|
|
|
/* This driver is based on the information available in the datasheet of the
|
|
"Comtech SDVBT-3K6M" tuner ( K1000737843.pdf ) which features the MT2060 register map :
|
|
|
|
I2C Address : 0x60
|
|
|
|
Reg.No | B7 | B6 | B5 | B4 | B3 | B2 | B1 | B0 | ( defaults )
|
|
--------------------------------------------------------------------------------
|
|
00 | [ PART ] | [ REV ] | R = 0x63
|
|
01 | [ LNABAND ] | [ NUM1(5:2) ] | RW = 0x3F
|
|
02 | [ DIV1 ] | RW = 0x74
|
|
03 | FM1CA | FM1SS | [ NUM1(1:0) ] | [ NUM2(3:0) ] | RW = 0x00
|
|
04 | NUM2(11:4) ] | RW = 0x08
|
|
05 | [ DIV2 ] |NUM2(12)| RW = 0x93
|
|
06 | L1LK | [ TAD1 ] | L2LK | [ TAD2 ] | R
|
|
07 | [ FMF ] | R
|
|
08 | ? | FMCAL | ? | ? | ? | ? | ? | TEMP | R
|
|
09 | 0 | 0 | [ FMGC ] | 0 | GP02 | GP01 | 0 | RW = 0x20
|
|
0A | ??
|
|
0B | 0 | 0 | 1 | 1 | 0 | 0 | [ VGAG ] | RW = 0x30
|
|
0C | V1CSE | 1 | 1 | 1 | 1 | 1 | 1 | 1 | RW = 0xFF
|
|
0D | 1 | 0 | [ V1CS ] | RW = 0xB0
|
|
0E | ??
|
|
0F | ??
|
|
10 | ??
|
|
11 | [ LOTO ] | 0 | 0 | 1 | 0 | RW = 0x42
|
|
|
|
PART : Part code : 6 for MT2060
|
|
REV : Revision code : 3 for current revision
|
|
LNABAND : Input frequency range : ( See code for details )
|
|
NUM1 / DIV1 / NUM2 / DIV2 : Frequencies programming ( See code for details )
|
|
FM1CA : Calibration Start Bit
|
|
FM1SS : Calibration Single Step bit
|
|
L1LK : LO1 Lock Detect
|
|
TAD1 : Tune Line ADC ( ? )
|
|
L2LK : LO2 Lock Detect
|
|
TAD2 : Tune Line ADC ( ? )
|
|
FMF : Estimated first IF Center frequency Offset ( ? )
|
|
FM1CAL : Calibration done bit
|
|
TEMP : On chip temperature sensor
|
|
FMCG : Mixer 1 Cap Gain ( ? )
|
|
GP01 / GP02 : Programmable digital outputs. Unconnected pins ?
|
|
V1CSE : LO1 VCO Automatic Capacitor Select Enable ( ? )
|
|
V1CS : LO1 Capacitor Selection Value ( ? )
|
|
LOTO : LO Timeout ( ? )
|
|
VGAG : Tuner Output gain
|
|
*/
|
|
|
|
#define I2C_ADDRESS 0x60
|
|
|
|
#define REG_PART_REV 0
|
|
#define REG_LO1C1 1
|
|
#define REG_LO1C2 2
|
|
#define REG_LO2C1 3
|
|
#define REG_LO2C2 4
|
|
#define REG_LO2C3 5
|
|
#define REG_LO_STATUS 6
|
|
#define REG_FM_FREQ 7
|
|
#define REG_MISC_STAT 8
|
|
#define REG_MISC_CTRL 9
|
|
#define REG_RESERVED_A 0x0A
|
|
#define REG_VGAG 0x0B
|
|
#define REG_LO1B1 0x0C
|
|
#define REG_LO1B2 0x0D
|
|
#define REG_LOTO 0x11
|
|
|
|
#define PART_REV 0x63 // The current driver works only with PART=6 and REV=3 chips
|
|
|
|
struct mt2060_priv {
|
|
struct mt2060_config *cfg;
|
|
struct i2c_adapter *i2c;
|
|
|
|
u32 frequency;
|
|
u16 if1_freq;
|
|
u8 fmfreq;
|
|
};
|
|
|
|
#endif
|