mirror of
https://github.com/torvalds/linux.git
synced 2024-11-16 17:12:06 +00:00
0e98de67ba
All the PHY configuration other than VBUS, ID GND and OTG SRP are removed from twl6030. The phy configurations are taken care by the dedicated usb2 phy driver. So twl6030 is made as comparator driver for VBUS and ID detection. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
142 lines
4.4 KiB
Plaintext
142 lines
4.4 KiB
Plaintext
#
|
|
# USB OTG infrastructure may be needed for peripheral-only, host-only,
|
|
# or OTG-capable configurations when OTG transceivers or controllers
|
|
# are used.
|
|
#
|
|
|
|
comment "OTG and related infrastructure"
|
|
|
|
config USB_OTG_UTILS
|
|
bool
|
|
help
|
|
Select this to make sure the build includes objects from
|
|
the OTG infrastructure directory.
|
|
|
|
if USB || USB_GADGET
|
|
|
|
#
|
|
# USB Transceiver Drivers
|
|
#
|
|
config USB_GPIO_VBUS
|
|
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
|
|
depends on GENERIC_GPIO
|
|
select USB_OTG_UTILS
|
|
help
|
|
Provides simple GPIO VBUS sensing for controllers with an
|
|
internal transceiver via the usb_phy interface, and
|
|
optionally control of a D+ pullup GPIO as well as a VBUS
|
|
current limit regulator.
|
|
|
|
config ISP1301_OMAP
|
|
tristate "Philips ISP1301 with OMAP OTG"
|
|
depends on I2C && ARCH_OMAP_OTG
|
|
select USB_OTG_UTILS
|
|
help
|
|
If you say yes here you get support for the Philips ISP1301
|
|
USB-On-The-Go transceiver working with the OMAP OTG controller.
|
|
The ISP1301 is a full speed USB transceiver which is used in
|
|
products including H2, H3, and H4 development boards for Texas
|
|
Instruments OMAP processors.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called isp1301_omap.
|
|
|
|
config USB_ULPI
|
|
bool "Generic ULPI Transceiver Driver"
|
|
depends on ARM
|
|
select USB_OTG_UTILS
|
|
help
|
|
Enable this to support ULPI connected USB OTG transceivers which
|
|
are likely found on embedded boards.
|
|
|
|
config USB_ULPI_VIEWPORT
|
|
bool
|
|
depends on USB_ULPI
|
|
help
|
|
Provides read/write operations to the ULPI phy register set for
|
|
controllers with a viewport register (e.g. Chipidea/ARC controllers).
|
|
|
|
config TWL4030_USB
|
|
tristate "TWL4030 USB Transceiver Driver"
|
|
depends on TWL4030_CORE && REGULATOR_TWL4030
|
|
select USB_OTG_UTILS
|
|
help
|
|
Enable this to support the USB OTG transceiver on TWL4030
|
|
family chips (including the TWL5030 and TPS659x0 devices).
|
|
This transceiver supports high and full speed devices plus,
|
|
in host mode, low speed.
|
|
|
|
config TWL6030_USB
|
|
tristate "TWL6030 USB Transceiver Driver"
|
|
depends on TWL4030_CORE && OMAP_USB2
|
|
select USB_OTG_UTILS
|
|
help
|
|
Enable this to support the USB OTG transceiver on TWL6030
|
|
family chips. This TWL6030 transceiver has the VBUS and ID GND
|
|
and OTG SRP events capabilities. For all other transceiver functionality
|
|
UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
|
|
are hooked to this driver through platform_data structure.
|
|
The definition of internal PHY APIs are in the mach-omap2 layer.
|
|
|
|
config NOP_USB_XCEIV
|
|
tristate "NOP USB Transceiver Driver"
|
|
select USB_OTG_UTILS
|
|
help
|
|
This driver is to be used by all the usb transceiver which are either
|
|
built-in with usb ip or which are autonomous and doesn't require any
|
|
phy programming such as ISP1x04 etc.
|
|
|
|
config USB_MSM_OTG
|
|
tristate "OTG support for Qualcomm on-chip USB controller"
|
|
depends on (USB || USB_GADGET) && ARCH_MSM
|
|
select USB_OTG_UTILS
|
|
help
|
|
Enable this to support the USB OTG transceiver on MSM chips. It
|
|
handles PHY initialization, clock management, and workarounds
|
|
required after resetting the hardware and power management.
|
|
This driver is required even for peripheral only or host only
|
|
mode configurations.
|
|
This driver is not supported on boards like trout which
|
|
has an external PHY.
|
|
|
|
config AB8500_USB
|
|
tristate "AB8500 USB Transceiver Driver"
|
|
depends on AB8500_CORE
|
|
select USB_OTG_UTILS
|
|
help
|
|
Enable this to support the USB OTG transceiver in AB8500 chip.
|
|
This transceiver supports high and full speed devices plus,
|
|
in host mode, low speed.
|
|
|
|
config FSL_USB2_OTG
|
|
bool "Freescale USB OTG Transceiver Driver"
|
|
depends on USB_EHCI_FSL && USB_GADGET_FSL_USB2 && USB_SUSPEND
|
|
select USB_OTG
|
|
select USB_OTG_UTILS
|
|
help
|
|
Enable this to support Freescale USB OTG transceiver.
|
|
|
|
config USB_MXS_PHY
|
|
tristate "Freescale MXS USB PHY support"
|
|
depends on ARCH_MXC || ARCH_MXS
|
|
select STMP_DEVICE
|
|
select USB_OTG_UTILS
|
|
help
|
|
Enable this to support the Freescale MXS USB PHY.
|
|
|
|
MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
|
|
|
|
config USB_MV_OTG
|
|
tristate "Marvell USB OTG support"
|
|
depends on USB_EHCI_MV && USB_MV_UDC && USB_SUSPEND
|
|
select USB_OTG
|
|
select USB_OTG_UTILS
|
|
help
|
|
Say Y here if you want to build Marvell USB OTG transciever
|
|
driver in kernel (including PXA and MMP series). This driver
|
|
implements role switch between EHCI host driver and gadget driver.
|
|
|
|
To compile this driver as a module, choose M here.
|
|
|
|
endif # USB || OTG
|