linux/drivers/bus/Kconfig
Linus Torvalds d461e96cd2 ARM: SoC drivers for 5.16
These are all the driver updates for SoC specific drivers. There
 are a couple of subsystems with individual maintainers picking up
 their patches here:
 
  - The reset controller subsystem add support for a few new SoC
    variants to existing drivers, along with other minor improvements
 
  - The OP-TEE subsystem gets a driver for the ARM FF-A transport
 
  - The memory controller subsystem has improvements for Tegra,
    Mediatek, Renesas, Freescale and Broadcom specific drivers.
 
  - The tegra cpuidle driver changes get merged through this
    tree this time. There are only minor changes, but they depend
    on other tegra driver updates here.
 
  - The ep93xx platform finally moves to using the drivers/clk/
    subsystem, moving the code out of arch/arm in the process.
    This depends on a small sound driver change that is included
    here as well.
 
  - There are some minor updates for Qualcomm and Tegra specific
    firmware drivers.
 
 The other driver updates are mainly for drivers/soc, which contains
 a mixture of vendor specific drivers that don't really fit elsewhere:
 
  - Mediatek drivers gain more support for MT8192, with new support for
    hw-mutex and mmsys routing, plus support for reset lines in the
    mmsys driver.
 
  - Qualcomm gains a new "sleep stats" driver, and support for
    the "Generic Packet Router" in the APR driver.
 
  - There is a new user interface for routing the UARTS on ASpeed
    BMCs, something that apparently nobody else has needed so far.
 
  - More drivers can now be built as loadable modules, in particular
    for Broadcom and Samsung platforms.
 
  - Lots of improvements to the TI sysc driver for better suspend/resume
    support
 
 Finally, there are lots of minor cleanups and new device IDs for
 amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx, layerscape,
 allwinner, broadcom, and omap.
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmGCvKgACgkQmmx57+YA
 GNnNfw/8DDTfMUycVvtaNslYlWri0/2O0nSqhNIIbTAcVuD/x5qo/McDhKuv+ldM
 BoTDMjRYZfQkrNXSEj3MaxB9E0o6Srva5SM8y4+Koe0VVtvEVovjYkXOhXqSEWWl
 aqVIe0S6Y1rF/KxJlvAfGxYHb5d+6aYqzdmhjURpXNGxqpSHb9/hqisY97Q9TpnD
 6lQZOz9d1JNDq0eOh1qjcfuMjg1EHZHDZJyioCvyX38KIl2q7p3ll2z/eqrrDhQZ
 TrvL/YVosTXqBcAfi47Oz+n/CX2i0MrjVO8nfPSGOq5UL4Al3SZD4XYY96IOIQrH
 +XGFigGGAkV2LfKSEPNJWaq7g+SiQUr2jc3p8b4Zxde8/+5M127/gotiPddyG2LX
 1OnFRnPskgRApGqHjGEcEzzJUTag7Hc+YVH82TMEHZhSDMq6i30k9UnyfXsziZDV
 8CrkOpjuSg+YxFv/83bfa1pIoYtFfjGr16mq4muajodnX7+b7My9iv+2Oo2iQM9y
 DwRUKj7+eap23SEUpi4et6HlNpoF6yJMbt5Ae1k+gTK2DvQ4Cx6n4QJz/I7WC1Wp
 BdVhvSH8XVppVLtQqODud+VWvLgLerRxUpGRdbS8r5VsnNUJTvaS4YGMpm9616G7
 TrgUSSvsyu1lLqbWMh+pOCk4l3r64vSUn581hrIw6jtioNGvMdE=
 =tUuj
 -----END PGP SIGNATURE-----

Merge tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "These are all the driver updates for SoC specific drivers. There are a
  couple of subsystems with individual maintainers picking up their
  patches here:

   - The reset controller subsystem add support for a few new SoC
     variants to existing drivers, along with other minor improvements

   - The OP-TEE subsystem gets a driver for the ARM FF-A transport

   - The memory controller subsystem has improvements for Tegra,
     Mediatek, Renesas, Freescale and Broadcom specific drivers.

   - The tegra cpuidle driver changes get merged through this tree this
     time. There are only minor changes, but they depend on other tegra
     driver updates here.

   - The ep93xx platform finally moves to using the drivers/clk/
     subsystem, moving the code out of arch/arm in the process. This
     depends on a small sound driver change that is included here as
     well.

   - There are some minor updates for Qualcomm and Tegra specific
     firmware drivers.

  The other driver updates are mainly for drivers/soc, which contains a
  mixture of vendor specific drivers that don't really fit elsewhere:

   - Mediatek drivers gain more support for MT8192, with new support for
     hw-mutex and mmsys routing, plus support for reset lines in the
     mmsys driver.

   - Qualcomm gains a new "sleep stats" driver, and support for the
     "Generic Packet Router" in the APR driver.

   - There is a new user interface for routing the UARTS on ASpeed BMCs,
     something that apparently nobody else has needed so far.

   - More drivers can now be built as loadable modules, in particular
     for Broadcom and Samsung platforms.

   - Lots of improvements to the TI sysc driver for better
     suspend/resume support"

  Finally, there are lots of minor cleanups and new device IDs for
  amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
  layerscape, allwinner, broadcom, and omap"

* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
  optee: Fix spelling mistake "reclain" -> "reclaim"
  Revert "firmware: qcom: scm: Add support for MC boot address API"
  qcom: spm: allow compile-testing
  firmware: arm_ffa: Remove unused 'compat_version' variable
  soc: samsung: exynos-chipid: add exynosautov9 SoC support
  firmware: qcom: scm: Don't break compile test on non-ARM platforms
  soc: qcom: smp2p: Add of_node_put() before goto
  soc: qcom: apr: Add of_node_put() before return
  soc: qcom: qcom_stats: Fix client votes offset
  soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
  dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
  ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
  firmware: qcom: scm: Add support for MC boot address API
  soc: qcom: spm: Add 8916 SPM register data
  dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
  soc: qcom: socinfo: Add PM8150C and SMB2351 models
  firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
  soc: aspeed: Add UART routing support
  soc: fsl: dpio: rename the enqueue descriptor variable
  soc: fsl: dpio: use an explicit NULL instead of 0
  ...
2021-11-03 17:00:52 -07:00

245 lines
7.7 KiB
Plaintext

# SPDX-License-Identifier: GPL-2.0
#
# Bus Devices
#
menu "Bus devices"
config ARM_CCI
bool
config ARM_CCI400_COMMON
bool
select ARM_CCI
config ARM_CCI400_PORT_CTRL
bool
depends on ARM && OF && CPU_V7
select ARM_CCI400_COMMON
help
Low level power management driver for CCI400 cache coherent
interconnect for ARM platforms.
config ARM_INTEGRATOR_LM
bool "ARM Integrator Logic Module bus"
depends on HAS_IOMEM
depends on ARCH_INTEGRATOR || COMPILE_TEST
default ARCH_INTEGRATOR
help
Say y here to enable support for the ARM Logic Module bus
found on the ARM Integrator AP (Application Platform)
config BRCMSTB_GISB_ARB
tristate "Broadcom STB GISB bus arbiter"
depends on ARM || ARM64 || MIPS
default ARCH_BRCMSTB || BMIPS_GENERIC
help
Driver for the Broadcom Set Top Box System-on-a-chip internal bus
arbiter. This driver provides timeout and target abort error handling
and internal bus master decoding.
config BT1_APB
bool "Baikal-T1 APB-bus driver"
depends on MIPS_BAIKAL_T1 || COMPILE_TEST
select REGMAP_MMIO
help
Baikal-T1 AXI-APB bridge is used to access the SoC subsystem CSRs.
IO requests are routed to this bus by means of the DW AMBA 3 AXI
Interconnect. In case of any APB protocol collisions, slave device
not responding on timeout an IRQ is raised with an erroneous address
reported to the APB terminator (APB Errors Handler Block). This
driver provides the interrupt handler to detect the erroneous
address, prints an error message about the address fault, updates an
errors counter. The counter and the APB-bus operations timeout can be
accessed via corresponding sysfs nodes.
config BT1_AXI
bool "Baikal-T1 AXI-bus driver"
depends on MIPS_BAIKAL_T1 || COMPILE_TEST
select MFD_SYSCON
help
AXI3-bus is the main communication bus connecting all high-speed
peripheral IP-cores with RAM controller and with MIPS P5600 cores on
Baikal-T1 SoC. Traffic arbitration is done by means of DW AMBA 3 AXI
Interconnect (so called AXI Main Interconnect) routing IO requests
from one SoC block to another. This driver provides a way to detect
any bus protocol errors and device not responding situations by
means of an embedded on top of the interconnect errors handler
block (EHB). AXI Interconnect QoS arbitration tuning is currently
unsupported.
config MOXTET
tristate "CZ.NIC Turris Mox module configuration bus"
depends on SPI_MASTER && OF
help
Say yes here to add support for the module configuration bus found
on CZ.NIC's Turris Mox. This is needed for the ability to discover
the order in which the modules are connected and to get/set some of
their settings. For example the GPIOs on Mox SFP module are
configured through this bus.
config HISILICON_LPC
bool "Support for ISA I/O space on HiSilicon Hip06/7"
depends on (ARM64 && ARCH_HISI) || (COMPILE_TEST && !ALPHA && !HEXAGON && !PARISC)
depends on HAS_IOMEM
select INDIRECT_PIO if ARM64
help
Driver to enable I/O access to devices attached to the Low Pin
Count bus on the HiSilicon Hip06/7 SoC.
config IMX_WEIM
bool "Freescale EIM DRIVER"
depends on ARCH_MXC
help
Driver for i.MX WEIM controller.
The WEIM(Wireless External Interface Module) works like a bus.
You can attach many different devices on it, such as NOR, onenand.
config INTEL_IXP4XX_EB
bool "Intel IXP4xx expansion bus interface driver"
depends on HAS_IOMEM
depends on ARCH_IXP4XX || COMPILE_TEST
default ARCH_IXP4XX
select MFD_SYSCON
help
Driver for the Intel IXP4xx expansion bus interface. The driver is
needed to set up various chip select configuration parameters before
devices on the expansion bus can be discovered.
config MIPS_CDMM
bool "MIPS Common Device Memory Map (CDMM) Driver"
depends on CPU_MIPSR2 || CPU_MIPSR5
help
Driver needed for the MIPS Common Device Memory Map bus in MIPS
cores. This bus is for per-CPU tightly coupled devices such as the
Fast Debug Channel (FDC).
For this to work, either your bootloader needs to enable the CDMM
region at an unused physical address on the boot CPU, or else your
platform code needs to implement mips_cdmm_phys_base() (see
asm/cdmm.h).
config MVEBU_MBUS
bool
depends on PLAT_ORION
help
Driver needed for the MBus configuration on Marvell EBU SoCs
(Kirkwood, Dove, Orion5x, MV78XX0 and Armada 370/XP).
config OMAP_INTERCONNECT
tristate "OMAP INTERCONNECT DRIVER"
depends on ARCH_OMAP2PLUS
help
Driver to enable OMAP interconnect error handling driver.
config OMAP_OCP2SCP
tristate "OMAP OCP2SCP DRIVER"
depends on ARCH_OMAP2PLUS
help
Driver to enable ocp2scp module which transforms ocp interface
protocol to scp protocol. In OMAP4, USB PHY is connected via
OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
OCP2SCP.
config QCOM_EBI2
bool "Qualcomm External Bus Interface 2 (EBI2)"
depends on HAS_IOMEM
depends on ARCH_QCOM || COMPILE_TEST
default ARCH_QCOM
help
Say y here to enable support for the Qualcomm External Bus
Interface 2, which can be used to connect things like NAND Flash,
SRAM, ethernet adapters, FPGAs and LCD displays.
config SUN50I_DE2_BUS
bool "Allwinner A64 DE2 Bus Driver"
default ARM64
depends on ARCH_SUNXI
select SUNXI_SRAM
help
Say y here to enable support for Allwinner A64 DE2 bus driver. It's
mostly transparent, but a SRAM region needs to be claimed in the SRAM
controller to make the all blocks in the DE2 part accessible.
config SUNXI_RSB
tristate "Allwinner sunXi Reduced Serial Bus Driver"
default MACH_SUN8I || MACH_SUN9I || ARM64
depends on ARCH_SUNXI
select REGMAP
help
Say y here to enable support for Allwinner's Reduced Serial Bus
(RSB) support. This controller is responsible for communicating
with various RSB based devices, such as AXP223, AXP8XX PMICs,
and AC100/AC200 ICs.
config TEGRA_ACONNECT
tristate "Tegra ACONNECT Bus Driver"
depends on ARCH_TEGRA_210_SOC
depends on OF && PM
help
Driver for the Tegra ACONNECT bus which is used to interface with
the devices inside the Audio Processing Engine (APE) for Tegra210.
config TEGRA_GMI
tristate "Tegra Generic Memory Interface bus driver"
depends on ARCH_TEGRA
help
Driver for the Tegra Generic Memory Interface bus which can be used
to attach devices such as NOR, UART, FPGA and more.
config TI_PWMSS
bool
default y if (ARCH_OMAP2PLUS) && (PWM_TIECAP || PWM_TIEHRPWM || TI_EQEP)
help
PWM Subsystem driver support for AM33xx SOC.
PWM submodules require PWM config space access from submodule
drivers and require common parent driver support.
config TI_SYSC
bool "TI sysc interconnect target module driver"
depends on ARCH_OMAP2PLUS
help
Generic driver for Texas Instruments interconnect target module
found on many TI SoCs.
config TS_NBUS
tristate "Technologic Systems NBUS Driver"
depends on SOC_IMX28
depends on OF_GPIO && PWM
help
Driver for the Technologic Systems NBUS which is used to interface
with the peripherals in the FPGA of the TS-4600 SoM.
config UNIPHIER_SYSTEM_BUS
tristate "UniPhier System Bus driver"
depends on ARCH_UNIPHIER && OF
default y
help
Support for UniPhier System Bus, a simple external bus. This is
needed to use on-board devices connected to UniPhier SoCs.
config VEXPRESS_CONFIG
tristate "Versatile Express configuration bus"
default y if ARCH_VEXPRESS
depends on ARM || ARM64
depends on OF
select REGMAP
help
Platform configuration infrastructure for the ARM Ltd.
Versatile Express.
config DA8XX_MSTPRI
bool "TI da8xx master peripheral priority driver"
depends on ARCH_DAVINCI_DA8XX
help
Driver for Texas Instruments da8xx master peripheral priority
configuration. Allows to adjust the priorities of all master
peripherals.
source "drivers/bus/fsl-mc/Kconfig"
source "drivers/bus/mhi/Kconfig"
endmenu