linux/drivers/usb/musb/Kconfig
Arnd Bergmann a8d191c8bb usb: musb: omap2plus bus glue needs USB host support
The musb/omap2430.c bus glue driver calls usb_hcd_poll_rh_status,
which is only available if CONFIG_USB is also set, i.e. we
are building USB host mode and not just endpoint mode.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-05-14 09:23:32 -05:00

167 lines
4.4 KiB
Plaintext

#
# USB Dual Role (OTG-ready) Controller Drivers
# for silicon based on Mentor Graphics INVENTRA designs
#
# (M)HDRC = (Multipoint) Highspeed Dual-Role Controller
config USB_MUSB_HDRC
tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)'
depends on (USB || USB_GADGET)
help
Say Y here if your system has a dual role high speed USB
controller based on the Mentor Graphics silicon IP. Then
configure options to match your silicon and the board
it's being used with, including the USB peripheral role,
or the USB host role, or both.
Texas Instruments families using this IP include DaVinci
(35x, 644x ...), OMAP 243x, OMAP 3, and TUSB 6010.
Analog Devices parts using this IP include Blackfin BF54x,
BF525 and BF527.
If you do not know what this is, please say N.
To compile this driver as a module, choose M here; the
module will be called "musb-hdrc".
if USB_MUSB_HDRC
choice
bool "MUSB Mode Selection"
default USB_MUSB_DUAL_ROLE if (USB && USB_GADGET)
default USB_MUSB_HOST if (USB && !USB_GADGET)
default USB_MUSB_GADGET if (!USB && USB_GADGET)
config USB_MUSB_HOST
bool "Host only mode"
depends on USB=y || USB=USB_MUSB_HDRC
help
Select this when you want to use MUSB in host mode only,
thereby the gadget feature will be regressed.
config USB_MUSB_GADGET
bool "Gadget only mode"
depends on USB_GADGET=y || USB_GADGET=USB_MUSB_HDRC
depends on HAS_DMA
help
Select this when you want to use MUSB in gadget mode only,
thereby the host feature will be regressed.
config USB_MUSB_DUAL_ROLE
bool "Dual Role mode"
depends on ((USB=y || USB=USB_MUSB_HDRC) && (USB_GADGET=y || USB_GADGET=USB_MUSB_HDRC))
depends on HAS_DMA
help
This is the default mode of working of MUSB controller where
both host and gadget features are enabled.
endchoice
choice
prompt "Platform Glue Layer"
config USB_MUSB_DAVINCI
tristate "DaVinci"
depends on ARCH_DAVINCI_DMx
depends on BROKEN
config USB_MUSB_DA8XX
tristate "DA8xx/OMAP-L1x"
depends on ARCH_DAVINCI_DA8XX
depends on BROKEN
config USB_MUSB_TUSB6010
tristate "TUSB6010"
config USB_MUSB_OMAP2PLUS
tristate "OMAP2430 and onwards"
depends on ARCH_OMAP2PLUS && USB
select GENERIC_PHY
config USB_MUSB_AM35X
tristate "AM35x"
depends on ARCH_OMAP
config USB_MUSB_DSPS
tristate "TI DSPS platforms"
select USB_MUSB_AM335X_CHILD
depends on OF_IRQ
config USB_MUSB_BLACKFIN
tristate "Blackfin"
depends on (BF54x && !BF544) || (BF52x && ! BF522 && !BF523)
config USB_MUSB_UX500
tristate "Ux500 platforms"
config USB_MUSB_JZ4740
tristate "JZ4740"
depends on MACH_JZ4740 || COMPILE_TEST
depends on USB_MUSB_GADGET
depends on USB_OTG_BLACKLIST_HUB
endchoice
config USB_MUSB_AM335X_CHILD
tristate
choice
prompt 'MUSB DMA mode'
default MUSB_PIO_ONLY if ARCH_MULTIPLATFORM || USB_MUSB_JZ4740
default USB_UX500_DMA if USB_MUSB_UX500
default USB_INVENTRA_DMA if USB_MUSB_OMAP2PLUS || USB_MUSB_BLACKFIN
default USB_TI_CPPI_DMA if USB_MUSB_DAVINCI
default USB_TUSB_OMAP_DMA if USB_MUSB_TUSB6010
default MUSB_PIO_ONLY if USB_MUSB_TUSB6010 || USB_MUSB_DA8XX || USB_MUSB_AM35X \
|| USB_MUSB_DSPS
help
Unfortunately, only one option can be enabled here. Ideally one
should be able to build all these drivers into one kernel to
allow using DMA on multiplatform kernels.
config USB_UX500_DMA
bool 'ST Ericsson Ux500'
depends on USB_MUSB_UX500
help
Enable DMA transfers on UX500 platforms.
config USB_INVENTRA_DMA
bool 'Inventra'
depends on USB_MUSB_OMAP2PLUS || USB_MUSB_BLACKFIN
help
Enable DMA transfers using Mentor's engine.
config USB_TI_CPPI_DMA
bool 'TI CPPI (Davinci)'
depends on USB_MUSB_DAVINCI
help
Enable DMA transfers when TI CPPI DMA is available.
config USB_TI_CPPI41_DMA
bool 'TI CPPI 4.1 (AM335x)'
depends on ARCH_OMAP
select TI_CPPI41
config USB_TUSB_OMAP_DMA
bool 'TUSB 6010'
depends on USB_MUSB_TUSB6010 = USB_MUSB_HDRC # both built-in or both modules
depends on ARCH_OMAP
help
Enable DMA transfers on TUSB 6010 when OMAP DMA is available.
config MUSB_PIO_ONLY
bool 'Disable DMA (always use PIO)'
help
All data is copied between memory and FIFO by the CPU.
DMA controllers are ignored.
Do not choose this unless DMA support for your SOC or board
is unavailable (or unstable). When DMA is enabled at compile time,
you can still disable it at run time using the "use_dma=n" module
parameter.
endchoice
endif # USB_MUSB_HDRC