mirror of
https://github.com/torvalds/linux.git
synced 2024-11-18 10:01:43 +00:00
6568eccd10
We used to set up the GPIO used for the SMC ethernet IRQ by requesting the GPIO line explicitly. As we recently established that specifying the GPIO controller as interrupt parent and requesting one of its interrupts by reference should be enough, we do away with this. Incidentally, the Nomadik GPIO chip driver handles this just fine: the IRQ is set up and fired as expected. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
102 lines
2.0 KiB
Plaintext
102 lines
2.0 KiB
Plaintext
/*
|
|
* Device Tree for the ST-Ericsson Nomadik S8815 board
|
|
* Produced by Calao Systems
|
|
*/
|
|
|
|
/dts-v1/;
|
|
/include/ "ste-nomadik-stn8815.dtsi"
|
|
|
|
/ {
|
|
model = "Calao Systems USB-S8815";
|
|
compatible = "calaosystems,usb-s8815";
|
|
|
|
chosen {
|
|
bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
|
|
};
|
|
|
|
/* This is where the interrupt is routed on the S8815 board */
|
|
external-bus@34000000 {
|
|
ethernet@300 {
|
|
interrupt-parent = <&gpio3>;
|
|
interrupts = <8 0x1>;
|
|
};
|
|
};
|
|
|
|
src@101e0000 {
|
|
/* These chrystal drivers are not used on this board */
|
|
disable-sxtalo;
|
|
disable-mxtalo;
|
|
};
|
|
|
|
pinctrl {
|
|
/* Hog CD pins */
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cd_default_mode>;
|
|
|
|
mmcsd-cd {
|
|
cd_default_mode: cd_default {
|
|
cd_default_cfg1 {
|
|
/* CD input GPIO */
|
|
ste,pins = "GPIO111_H21";
|
|
ste,input = <0>;
|
|
};
|
|
cd_default_cfg2 {
|
|
/* CD GPIO biasing */
|
|
ste,pins = "GPIO112_J21";
|
|
ste,output = <0>;
|
|
};
|
|
};
|
|
};
|
|
user-led {
|
|
user_led_default_mode: user_led_default {
|
|
user_led_default_cfg {
|
|
ste,pins = "GPIO2_C5";
|
|
ste,output = <1>;
|
|
};
|
|
};
|
|
};
|
|
user-button {
|
|
user_button_default_mode: user_button_default {
|
|
user_button_default_cfg {
|
|
ste,pins = "GPIO3_A4";
|
|
ste,input = <0>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
/* Custom board node with GPIO pins to active etc */
|
|
usb-s8815 {
|
|
/* This will bias the MMC/SD card detect line */
|
|
mmcsd-gpio {
|
|
gpios = <&gpio3 16 0x1>;
|
|
};
|
|
};
|
|
|
|
/* The user LED on the board is set up to be used for heartbeat */
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
user-led {
|
|
label = "user_led";
|
|
gpios = <&gpio0 2 0x1>;
|
|
default-state = "off";
|
|
linux,default-trigger = "heartbeat";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&user_led_default_mode>;
|
|
};
|
|
};
|
|
|
|
/* User key mapped in as "escape" */
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
user-button {
|
|
label = "user_button";
|
|
gpios = <&gpio0 3 0x1>;
|
|
linux,code = <1>; /* KEY_ESC */
|
|
gpio-key,wakeup;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&user_button_default_mode>;
|
|
};
|
|
};
|
|
};
|