mirror of
https://github.com/torvalds/linux.git
synced 2024-11-13 23:51:39 +00:00
14bdef982c
No functional changes in this patch. Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
870 lines
22 KiB
C
870 lines
22 KiB
C
/*
|
|
* pata_sis.c - SiS ATA driver
|
|
*
|
|
* (C) 2005 Red Hat
|
|
* (C) 2007 Bartlomiej Zolnierkiewicz
|
|
*
|
|
* Based upon linux/drivers/ide/pci/sis5513.c
|
|
* Copyright (C) 1999-2000 Andre Hedrick <andre@linux-ide.org>
|
|
* Copyright (C) 2002 Lionel Bouton <Lionel.Bouton@inet6.fr>, Maintainer
|
|
* Copyright (C) 2003 Vojtech Pavlik <vojtech@suse.cz>
|
|
* SiS Taiwan : for direct support and hardware.
|
|
* Daniela Engert : for initial ATA100 advices and numerous others.
|
|
* John Fremlin, Manfred Spraul, Dave Morgan, Peter Kjellerstedt :
|
|
* for checking code correctness, providing patches.
|
|
* Original tests and design on the SiS620 chipset.
|
|
* ATA100 tests and design on the SiS735 chipset.
|
|
* ATA16/33 support from specs
|
|
* ATA133 support for SiS961/962 by L.C. Chang <lcchang@sis.com.tw>
|
|
*
|
|
*
|
|
* TODO
|
|
* Check MWDMA on drives that don't support MWDMA speed pio cycles ?
|
|
* More Testing
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/init.h>
|
|
#include <linux/blkdev.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/device.h>
|
|
#include <scsi/scsi_host.h>
|
|
#include <linux/libata.h>
|
|
#include <linux/ata.h>
|
|
#include "sis.h"
|
|
|
|
#define DRV_NAME "pata_sis"
|
|
#define DRV_VERSION "0.5.2"
|
|
|
|
struct sis_chipset {
|
|
u16 device; /* PCI host ID */
|
|
const struct ata_port_info *info; /* Info block */
|
|
/* Probably add family, cable detect type etc here to clean
|
|
up code later */
|
|
};
|
|
|
|
struct sis_laptop {
|
|
u16 device;
|
|
u16 subvendor;
|
|
u16 subdevice;
|
|
};
|
|
|
|
static const struct sis_laptop sis_laptop[] = {
|
|
/* devid, subvendor, subdev */
|
|
{ 0x5513, 0x1043, 0x1107 }, /* ASUS A6K */
|
|
{ 0x5513, 0x1734, 0x105F }, /* FSC Amilo A1630 */
|
|
{ 0x5513, 0x1071, 0x8640 }, /* EasyNote K5305 */
|
|
/* end marker */
|
|
{ 0, }
|
|
};
|
|
|
|
static int sis_short_ata40(struct pci_dev *dev)
|
|
{
|
|
const struct sis_laptop *lap = &sis_laptop[0];
|
|
|
|
while (lap->device) {
|
|
if (lap->device == dev->device &&
|
|
lap->subvendor == dev->subsystem_vendor &&
|
|
lap->subdevice == dev->subsystem_device)
|
|
return 1;
|
|
lap++;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* sis_old_port_base - return PCI configuration base for dev
|
|
* @adev: device
|
|
*
|
|
* Returns the base of the PCI configuration registers for this port
|
|
* number.
|
|
*/
|
|
|
|
static int sis_old_port_base(struct ata_device *adev)
|
|
{
|
|
return 0x40 + (4 * adev->link->ap->port_no) + (2 * adev->devno);
|
|
}
|
|
|
|
/**
|
|
* sis_133_cable_detect - check for 40/80 pin
|
|
* @ap: Port
|
|
* @deadline: deadline jiffies for the operation
|
|
*
|
|
* Perform cable detection for the later UDMA133 capable
|
|
* SiS chipset.
|
|
*/
|
|
|
|
static int sis_133_cable_detect(struct ata_port *ap)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u16 tmp;
|
|
|
|
/* The top bit of this register is the cable detect bit */
|
|
pci_read_config_word(pdev, 0x50 + 2 * ap->port_no, &tmp);
|
|
if ((tmp & 0x8000) && !sis_short_ata40(pdev))
|
|
return ATA_CBL_PATA40;
|
|
return ATA_CBL_PATA80;
|
|
}
|
|
|
|
/**
|
|
* sis_66_cable_detect - check for 40/80 pin
|
|
* @ap: Port
|
|
*
|
|
* Perform cable detection on the UDMA66, UDMA100 and early UDMA133
|
|
* SiS IDE controllers.
|
|
*/
|
|
|
|
static int sis_66_cable_detect(struct ata_port *ap)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u8 tmp;
|
|
|
|
/* Older chips keep cable detect in bits 4/5 of reg 0x48 */
|
|
pci_read_config_byte(pdev, 0x48, &tmp);
|
|
tmp >>= ap->port_no;
|
|
if ((tmp & 0x10) && !sis_short_ata40(pdev))
|
|
return ATA_CBL_PATA40;
|
|
return ATA_CBL_PATA80;
|
|
}
|
|
|
|
|
|
/**
|
|
* sis_pre_reset - probe begin
|
|
* @link: ATA link
|
|
* @deadline: deadline jiffies for the operation
|
|
*
|
|
* Set up cable type and use generic probe init
|
|
*/
|
|
|
|
static int sis_pre_reset(struct ata_link *link, unsigned long deadline)
|
|
{
|
|
static const struct pci_bits sis_enable_bits[] = {
|
|
{ 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
|
|
{ 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */
|
|
};
|
|
|
|
struct ata_port *ap = link->ap;
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
|
|
if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no]))
|
|
return -ENOENT;
|
|
|
|
/* Clear the FIFO settings. We can't enable the FIFO until
|
|
we know we are poking at a disk */
|
|
pci_write_config_byte(pdev, 0x4B, 0);
|
|
return ata_sff_prereset(link, deadline);
|
|
}
|
|
|
|
|
|
/**
|
|
* sis_set_fifo - Set RWP fifo bits for this device
|
|
* @ap: Port
|
|
* @adev: Device
|
|
*
|
|
* SIS chipsets implement prefetch/postwrite bits for each device
|
|
* on both channels. This functionality is not ATAPI compatible and
|
|
* must be configured according to the class of device present
|
|
*/
|
|
|
|
static void sis_set_fifo(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u8 fifoctrl;
|
|
u8 mask = 0x11;
|
|
|
|
mask <<= (2 * ap->port_no);
|
|
mask <<= adev->devno;
|
|
|
|
/* This holds various bits including the FIFO control */
|
|
pci_read_config_byte(pdev, 0x4B, &fifoctrl);
|
|
fifoctrl &= ~mask;
|
|
|
|
/* Enable for ATA (disk) only */
|
|
if (adev->class == ATA_DEV_ATA)
|
|
fifoctrl |= mask;
|
|
pci_write_config_byte(pdev, 0x4B, fifoctrl);
|
|
}
|
|
|
|
/**
|
|
* sis_old_set_piomode - Initialize host controller PATA PIO timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device we are configuring for.
|
|
*
|
|
* Set PIO mode for device, in host controller PCI config space. This
|
|
* function handles PIO set up for all chips that are pre ATA100 and
|
|
* also early ATA100 devices.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int port = sis_old_port_base(adev);
|
|
u8 t1, t2;
|
|
int speed = adev->pio_mode - XFER_PIO_0;
|
|
|
|
const u8 active[] = { 0x00, 0x07, 0x04, 0x03, 0x01 };
|
|
const u8 recovery[] = { 0x00, 0x06, 0x04, 0x03, 0x03 };
|
|
|
|
sis_set_fifo(ap, adev);
|
|
|
|
pci_read_config_byte(pdev, port, &t1);
|
|
pci_read_config_byte(pdev, port + 1, &t2);
|
|
|
|
t1 &= ~0x0F; /* Clear active/recovery timings */
|
|
t2 &= ~0x07;
|
|
|
|
t1 |= active[speed];
|
|
t2 |= recovery[speed];
|
|
|
|
pci_write_config_byte(pdev, port, t1);
|
|
pci_write_config_byte(pdev, port + 1, t2);
|
|
}
|
|
|
|
/**
|
|
* sis_100_set_piomode - Initialize host controller PATA PIO timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device we are configuring for.
|
|
*
|
|
* Set PIO mode for device, in host controller PCI config space. This
|
|
* function handles PIO set up for ATA100 devices and early ATA133.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int port = sis_old_port_base(adev);
|
|
int speed = adev->pio_mode - XFER_PIO_0;
|
|
|
|
const u8 actrec[] = { 0x00, 0x67, 0x44, 0x33, 0x31 };
|
|
|
|
sis_set_fifo(ap, adev);
|
|
|
|
pci_write_config_byte(pdev, port, actrec[speed]);
|
|
}
|
|
|
|
/**
|
|
* sis_133_set_piomode - Initialize host controller PATA PIO timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device we are configuring for.
|
|
*
|
|
* Set PIO mode for device, in host controller PCI config space. This
|
|
* function handles PIO set up for the later ATA133 devices.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int port = 0x40;
|
|
u32 t1;
|
|
u32 reg54;
|
|
int speed = adev->pio_mode - XFER_PIO_0;
|
|
|
|
const u32 timing133[] = {
|
|
0x28269000, /* Recovery << 24 | Act << 16 | Ini << 12 */
|
|
0x0C266000,
|
|
0x04263000,
|
|
0x0C0A3000,
|
|
0x05093000
|
|
};
|
|
const u32 timing100[] = {
|
|
0x1E1C6000, /* Recovery << 24 | Act << 16 | Ini << 12 */
|
|
0x091C4000,
|
|
0x031C2000,
|
|
0x09072000,
|
|
0x04062000
|
|
};
|
|
|
|
sis_set_fifo(ap, adev);
|
|
|
|
/* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */
|
|
pci_read_config_dword(pdev, 0x54, ®54);
|
|
if (reg54 & 0x40000000)
|
|
port = 0x70;
|
|
port += 8 * ap->port_no + 4 * adev->devno;
|
|
|
|
pci_read_config_dword(pdev, port, &t1);
|
|
t1 &= 0xC0C00FFF; /* Mask out timing */
|
|
|
|
if (t1 & 0x08) /* 100 or 133 ? */
|
|
t1 |= timing133[speed];
|
|
else
|
|
t1 |= timing100[speed];
|
|
pci_write_config_byte(pdev, port, t1);
|
|
}
|
|
|
|
/**
|
|
* sis_old_set_dmamode - Initialize host controller PATA DMA timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device to program
|
|
*
|
|
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
|
|
* Handles pre UDMA and UDMA33 devices. Supports MWDMA as well unlike
|
|
* the old ide/pci driver.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void sis_old_set_dmamode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int speed = adev->dma_mode - XFER_MW_DMA_0;
|
|
int drive_pci = sis_old_port_base(adev);
|
|
u16 timing;
|
|
|
|
const u16 mwdma_bits[] = { 0x008, 0x302, 0x301 };
|
|
const u16 udma_bits[] = { 0xE000, 0xC000, 0xA000 };
|
|
|
|
pci_read_config_word(pdev, drive_pci, &timing);
|
|
|
|
if (adev->dma_mode < XFER_UDMA_0) {
|
|
/* bits 3-0 hold recovery timing bits 8-10 active timing and
|
|
the higher bits are dependant on the device */
|
|
timing &= ~0x870F;
|
|
timing |= mwdma_bits[speed];
|
|
} else {
|
|
/* Bit 15 is UDMA on/off, bit 13-14 are cycle time */
|
|
speed = adev->dma_mode - XFER_UDMA_0;
|
|
timing &= ~0x6000;
|
|
timing |= udma_bits[speed];
|
|
}
|
|
pci_write_config_word(pdev, drive_pci, timing);
|
|
}
|
|
|
|
/**
|
|
* sis_66_set_dmamode - Initialize host controller PATA DMA timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device to program
|
|
*
|
|
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
|
|
* Handles UDMA66 and early UDMA100 devices. Supports MWDMA as well unlike
|
|
* the old ide/pci driver.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int speed = adev->dma_mode - XFER_MW_DMA_0;
|
|
int drive_pci = sis_old_port_base(adev);
|
|
u16 timing;
|
|
|
|
/* MWDMA 0-2 and UDMA 0-5 */
|
|
const u16 mwdma_bits[] = { 0x008, 0x302, 0x301 };
|
|
const u16 udma_bits[] = { 0xF000, 0xD000, 0xB000, 0xA000, 0x9000, 0x8000 };
|
|
|
|
pci_read_config_word(pdev, drive_pci, &timing);
|
|
|
|
if (adev->dma_mode < XFER_UDMA_0) {
|
|
/* bits 3-0 hold recovery timing bits 8-10 active timing and
|
|
the higher bits are dependant on the device, bit 15 udma */
|
|
timing &= ~0x870F;
|
|
timing |= mwdma_bits[speed];
|
|
} else {
|
|
/* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
|
|
speed = adev->dma_mode - XFER_UDMA_0;
|
|
timing &= ~0xF000;
|
|
timing |= udma_bits[speed];
|
|
}
|
|
pci_write_config_word(pdev, drive_pci, timing);
|
|
}
|
|
|
|
/**
|
|
* sis_100_set_dmamode - Initialize host controller PATA DMA timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device to program
|
|
*
|
|
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
|
|
* Handles UDMA66 and early UDMA100 devices.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void sis_100_set_dmamode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int speed = adev->dma_mode - XFER_MW_DMA_0;
|
|
int drive_pci = sis_old_port_base(adev);
|
|
u8 timing;
|
|
|
|
const u8 udma_bits[] = { 0x8B, 0x87, 0x85, 0x83, 0x82, 0x81};
|
|
|
|
pci_read_config_byte(pdev, drive_pci + 1, &timing);
|
|
|
|
if (adev->dma_mode < XFER_UDMA_0) {
|
|
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
|
|
} else {
|
|
/* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
|
|
speed = adev->dma_mode - XFER_UDMA_0;
|
|
timing &= ~0x8F;
|
|
timing |= udma_bits[speed];
|
|
}
|
|
pci_write_config_byte(pdev, drive_pci + 1, timing);
|
|
}
|
|
|
|
/**
|
|
* sis_133_early_set_dmamode - Initialize host controller PATA DMA timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device to program
|
|
*
|
|
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
|
|
* Handles early SiS 961 bridges.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void sis_133_early_set_dmamode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int speed = adev->dma_mode - XFER_MW_DMA_0;
|
|
int drive_pci = sis_old_port_base(adev);
|
|
u8 timing;
|
|
/* Low 4 bits are timing */
|
|
static const u8 udma_bits[] = { 0x8F, 0x8A, 0x87, 0x85, 0x83, 0x82, 0x81};
|
|
|
|
pci_read_config_byte(pdev, drive_pci + 1, &timing);
|
|
|
|
if (adev->dma_mode < XFER_UDMA_0) {
|
|
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
|
|
} else {
|
|
/* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
|
|
speed = adev->dma_mode - XFER_UDMA_0;
|
|
timing &= ~0x8F;
|
|
timing |= udma_bits[speed];
|
|
}
|
|
pci_write_config_byte(pdev, drive_pci + 1, timing);
|
|
}
|
|
|
|
/**
|
|
* sis_133_set_dmamode - Initialize host controller PATA DMA timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device to program
|
|
*
|
|
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void sis_133_set_dmamode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int speed = adev->dma_mode - XFER_MW_DMA_0;
|
|
int port = 0x40;
|
|
u32 t1;
|
|
u32 reg54;
|
|
|
|
/* bits 4- cycle time 8 - cvs time */
|
|
static const u32 timing_u100[] = { 0x6B0, 0x470, 0x350, 0x140, 0x120, 0x110, 0x000 };
|
|
static const u32 timing_u133[] = { 0x9F0, 0x6A0, 0x470, 0x250, 0x230, 0x220, 0x210 };
|
|
|
|
/* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */
|
|
pci_read_config_dword(pdev, 0x54, ®54);
|
|
if (reg54 & 0x40000000)
|
|
port = 0x70;
|
|
port += (8 * ap->port_no) + (4 * adev->devno);
|
|
|
|
pci_read_config_dword(pdev, port, &t1);
|
|
|
|
if (adev->dma_mode < XFER_UDMA_0) {
|
|
t1 &= ~0x00000004;
|
|
/* FIXME: need data sheet to add MWDMA here. Also lacking on
|
|
ide/pci driver */
|
|
} else {
|
|
speed = adev->dma_mode - XFER_UDMA_0;
|
|
/* if & 8 no UDMA133 - need info for ... */
|
|
t1 &= ~0x00000FF0;
|
|
t1 |= 0x00000004;
|
|
if (t1 & 0x08)
|
|
t1 |= timing_u133[speed];
|
|
else
|
|
t1 |= timing_u100[speed];
|
|
}
|
|
pci_write_config_dword(pdev, port, t1);
|
|
}
|
|
|
|
static struct scsi_host_template sis_sht = {
|
|
ATA_BMDMA_SHT(DRV_NAME),
|
|
};
|
|
|
|
static struct ata_port_operations sis_133_for_sata_ops = {
|
|
.inherits = &ata_bmdma_port_ops,
|
|
.set_piomode = sis_133_set_piomode,
|
|
.set_dmamode = sis_133_set_dmamode,
|
|
.cable_detect = sis_133_cable_detect,
|
|
};
|
|
|
|
static struct ata_port_operations sis_base_ops = {
|
|
.inherits = &ata_bmdma_port_ops,
|
|
.prereset = sis_pre_reset,
|
|
};
|
|
|
|
static struct ata_port_operations sis_133_ops = {
|
|
.inherits = &sis_base_ops,
|
|
.set_piomode = sis_133_set_piomode,
|
|
.set_dmamode = sis_133_set_dmamode,
|
|
.cable_detect = sis_133_cable_detect,
|
|
};
|
|
|
|
static struct ata_port_operations sis_133_early_ops = {
|
|
.inherits = &sis_base_ops,
|
|
.set_piomode = sis_100_set_piomode,
|
|
.set_dmamode = sis_133_early_set_dmamode,
|
|
.cable_detect = sis_66_cable_detect,
|
|
};
|
|
|
|
static struct ata_port_operations sis_100_ops = {
|
|
.inherits = &sis_base_ops,
|
|
.set_piomode = sis_100_set_piomode,
|
|
.set_dmamode = sis_100_set_dmamode,
|
|
.cable_detect = sis_66_cable_detect,
|
|
};
|
|
|
|
static struct ata_port_operations sis_66_ops = {
|
|
.inherits = &sis_base_ops,
|
|
.set_piomode = sis_old_set_piomode,
|
|
.set_dmamode = sis_66_set_dmamode,
|
|
.cable_detect = sis_66_cable_detect,
|
|
};
|
|
|
|
static struct ata_port_operations sis_old_ops = {
|
|
.inherits = &sis_base_ops,
|
|
.set_piomode = sis_old_set_piomode,
|
|
.set_dmamode = sis_old_set_dmamode,
|
|
.cable_detect = ata_cable_40wire,
|
|
};
|
|
|
|
static const struct ata_port_info sis_info = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
/* No UDMA */
|
|
.port_ops = &sis_old_ops,
|
|
};
|
|
static const struct ata_port_info sis_info33 = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = ATA_UDMA2,
|
|
.port_ops = &sis_old_ops,
|
|
};
|
|
static const struct ata_port_info sis_info66 = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
/* No MWDMA */
|
|
.udma_mask = ATA_UDMA4,
|
|
.port_ops = &sis_66_ops,
|
|
};
|
|
static const struct ata_port_info sis_info100 = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
/* No MWDMA */
|
|
.udma_mask = ATA_UDMA5,
|
|
.port_ops = &sis_100_ops,
|
|
};
|
|
static const struct ata_port_info sis_info100_early = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
/* No MWDMA */
|
|
.udma_mask = ATA_UDMA5,
|
|
.port_ops = &sis_66_ops,
|
|
};
|
|
static const struct ata_port_info sis_info133 = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
/* No MWDMA */
|
|
.udma_mask = ATA_UDMA6,
|
|
.port_ops = &sis_133_ops,
|
|
};
|
|
const struct ata_port_info sis_info133_for_sata = {
|
|
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
|
|
.pio_mask = ATA_PIO4,
|
|
/* No MWDMA */
|
|
.udma_mask = ATA_UDMA6,
|
|
.port_ops = &sis_133_for_sata_ops,
|
|
};
|
|
static const struct ata_port_info sis_info133_early = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
/* No MWDMA */
|
|
.udma_mask = ATA_UDMA6,
|
|
.port_ops = &sis_133_early_ops,
|
|
};
|
|
|
|
/* Privately shared with the SiS180 SATA driver, not for use elsewhere */
|
|
EXPORT_SYMBOL_GPL(sis_info133_for_sata);
|
|
|
|
static void sis_fixup(struct pci_dev *pdev, struct sis_chipset *sis)
|
|
{
|
|
u16 regw;
|
|
u8 reg;
|
|
|
|
if (sis->info == &sis_info133) {
|
|
pci_read_config_word(pdev, 0x50, ®w);
|
|
if (regw & 0x08)
|
|
pci_write_config_word(pdev, 0x50, regw & ~0x08);
|
|
pci_read_config_word(pdev, 0x52, ®w);
|
|
if (regw & 0x08)
|
|
pci_write_config_word(pdev, 0x52, regw & ~0x08);
|
|
return;
|
|
}
|
|
|
|
if (sis->info == &sis_info133_early || sis->info == &sis_info100) {
|
|
/* Fix up latency */
|
|
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80);
|
|
/* Set compatibility bit */
|
|
pci_read_config_byte(pdev, 0x49, ®);
|
|
if (!(reg & 0x01))
|
|
pci_write_config_byte(pdev, 0x49, reg | 0x01);
|
|
return;
|
|
}
|
|
|
|
if (sis->info == &sis_info66 || sis->info == &sis_info100_early) {
|
|
/* Fix up latency */
|
|
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80);
|
|
/* Set compatibility bit */
|
|
pci_read_config_byte(pdev, 0x52, ®);
|
|
if (!(reg & 0x04))
|
|
pci_write_config_byte(pdev, 0x52, reg | 0x04);
|
|
return;
|
|
}
|
|
|
|
if (sis->info == &sis_info33) {
|
|
pci_read_config_byte(pdev, PCI_CLASS_PROG, ®);
|
|
if (( reg & 0x0F ) != 0x00)
|
|
pci_write_config_byte(pdev, PCI_CLASS_PROG, reg & 0xF0);
|
|
/* Fall through to ATA16 fixup below */
|
|
}
|
|
|
|
if (sis->info == &sis_info || sis->info == &sis_info33) {
|
|
/* force per drive recovery and active timings
|
|
needed on ATA_33 and below chips */
|
|
pci_read_config_byte(pdev, 0x52, ®);
|
|
if (!(reg & 0x08))
|
|
pci_write_config_byte(pdev, 0x52, reg|0x08);
|
|
return;
|
|
}
|
|
|
|
BUG();
|
|
}
|
|
|
|
/**
|
|
* sis_init_one - Register SiS ATA PCI device with kernel services
|
|
* @pdev: PCI device to register
|
|
* @ent: Entry in sis_pci_tbl matching with @pdev
|
|
*
|
|
* Called from kernel PCI layer. We probe for combined mode (sigh),
|
|
* and then hand over control to libata, for it to do the rest.
|
|
*
|
|
* LOCKING:
|
|
* Inherited from PCI layer (may sleep).
|
|
*
|
|
* RETURNS:
|
|
* Zero on success, or -ERRNO value.
|
|
*/
|
|
|
|
static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
|
|
{
|
|
static int printed_version;
|
|
const struct ata_port_info *ppi[] = { NULL, NULL };
|
|
struct pci_dev *host = NULL;
|
|
struct sis_chipset *chipset = NULL;
|
|
struct sis_chipset *sets;
|
|
int rc;
|
|
|
|
static struct sis_chipset sis_chipsets[] = {
|
|
|
|
{ 0x0968, &sis_info133 },
|
|
{ 0x0966, &sis_info133 },
|
|
{ 0x0965, &sis_info133 },
|
|
{ 0x0745, &sis_info100 },
|
|
{ 0x0735, &sis_info100 },
|
|
{ 0x0733, &sis_info100 },
|
|
{ 0x0635, &sis_info100 },
|
|
{ 0x0633, &sis_info100 },
|
|
|
|
{ 0x0730, &sis_info100_early }, /* 100 with ATA 66 layout */
|
|
{ 0x0550, &sis_info100_early }, /* 100 with ATA 66 layout */
|
|
|
|
{ 0x0640, &sis_info66 },
|
|
{ 0x0630, &sis_info66 },
|
|
{ 0x0620, &sis_info66 },
|
|
{ 0x0540, &sis_info66 },
|
|
{ 0x0530, &sis_info66 },
|
|
|
|
{ 0x5600, &sis_info33 },
|
|
{ 0x5598, &sis_info33 },
|
|
{ 0x5597, &sis_info33 },
|
|
{ 0x5591, &sis_info33 },
|
|
{ 0x5582, &sis_info33 },
|
|
{ 0x5581, &sis_info33 },
|
|
|
|
{ 0x5596, &sis_info },
|
|
{ 0x5571, &sis_info },
|
|
{ 0x5517, &sis_info },
|
|
{ 0x5511, &sis_info },
|
|
|
|
{0}
|
|
};
|
|
static struct sis_chipset sis133_early = {
|
|
0x0, &sis_info133_early
|
|
};
|
|
static struct sis_chipset sis133 = {
|
|
0x0, &sis_info133
|
|
};
|
|
static struct sis_chipset sis100_early = {
|
|
0x0, &sis_info100_early
|
|
};
|
|
static struct sis_chipset sis100 = {
|
|
0x0, &sis_info100
|
|
};
|
|
|
|
if (!printed_version++)
|
|
dev_printk(KERN_DEBUG, &pdev->dev,
|
|
"version " DRV_VERSION "\n");
|
|
|
|
rc = pcim_enable_device(pdev);
|
|
if (rc)
|
|
return rc;
|
|
|
|
/* We have to find the bridge first */
|
|
for (sets = &sis_chipsets[0]; sets->device; sets++) {
|
|
host = pci_get_device(PCI_VENDOR_ID_SI, sets->device, NULL);
|
|
if (host != NULL) {
|
|
chipset = sets; /* Match found */
|
|
if (sets->device == 0x630) { /* SIS630 */
|
|
if (host->revision >= 0x30) /* 630 ET */
|
|
chipset = &sis100_early;
|
|
}
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* Look for concealed bridges */
|
|
if (chipset == NULL) {
|
|
/* Second check */
|
|
u32 idemisc;
|
|
u16 trueid;
|
|
|
|
/* Disable ID masking and register remapping then
|
|
see what the real ID is */
|
|
|
|
pci_read_config_dword(pdev, 0x54, &idemisc);
|
|
pci_write_config_dword(pdev, 0x54, idemisc & 0x7fffffff);
|
|
pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid);
|
|
pci_write_config_dword(pdev, 0x54, idemisc);
|
|
|
|
switch(trueid) {
|
|
case 0x5518: /* SIS 962/963 */
|
|
chipset = &sis133;
|
|
if ((idemisc & 0x40000000) == 0) {
|
|
pci_write_config_dword(pdev, 0x54, idemisc | 0x40000000);
|
|
printk(KERN_INFO "SIS5513: Switching to 5513 register mapping\n");
|
|
}
|
|
break;
|
|
case 0x0180: /* SIS 965/965L */
|
|
chipset = &sis133;
|
|
break;
|
|
case 0x1180: /* SIS 966/966L */
|
|
chipset = &sis133;
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* Further check */
|
|
if (chipset == NULL) {
|
|
struct pci_dev *lpc_bridge;
|
|
u16 trueid;
|
|
u8 prefctl;
|
|
u8 idecfg;
|
|
|
|
/* Try the second unmasking technique */
|
|
pci_read_config_byte(pdev, 0x4a, &idecfg);
|
|
pci_write_config_byte(pdev, 0x4a, idecfg | 0x10);
|
|
pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid);
|
|
pci_write_config_byte(pdev, 0x4a, idecfg);
|
|
|
|
switch(trueid) {
|
|
case 0x5517:
|
|
lpc_bridge = pci_get_slot(pdev->bus, 0x10); /* Bus 0 Dev 2 Fn 0 */
|
|
if (lpc_bridge == NULL)
|
|
break;
|
|
pci_read_config_byte(pdev, 0x49, &prefctl);
|
|
pci_dev_put(lpc_bridge);
|
|
|
|
if (lpc_bridge->revision == 0x10 && (prefctl & 0x80)) {
|
|
chipset = &sis133_early;
|
|
break;
|
|
}
|
|
chipset = &sis100;
|
|
break;
|
|
}
|
|
}
|
|
pci_dev_put(host);
|
|
|
|
/* No chipset info, no support */
|
|
if (chipset == NULL)
|
|
return -ENODEV;
|
|
|
|
ppi[0] = chipset->info;
|
|
|
|
sis_fixup(pdev, chipset);
|
|
|
|
return ata_pci_sff_init_one(pdev, ppi, &sis_sht, chipset);
|
|
}
|
|
|
|
static const struct pci_device_id sis_pci_tbl[] = {
|
|
{ PCI_VDEVICE(SI, 0x5513), }, /* SiS 5513 */
|
|
{ PCI_VDEVICE(SI, 0x5518), }, /* SiS 5518 */
|
|
{ PCI_VDEVICE(SI, 0x1180), }, /* SiS 1180 */
|
|
|
|
{ }
|
|
};
|
|
|
|
static struct pci_driver sis_pci_driver = {
|
|
.name = DRV_NAME,
|
|
.id_table = sis_pci_tbl,
|
|
.probe = sis_init_one,
|
|
.remove = ata_pci_remove_one,
|
|
#ifdef CONFIG_PM
|
|
.suspend = ata_pci_device_suspend,
|
|
.resume = ata_pci_device_resume,
|
|
#endif
|
|
};
|
|
|
|
static int __init sis_init(void)
|
|
{
|
|
return pci_register_driver(&sis_pci_driver);
|
|
}
|
|
|
|
static void __exit sis_exit(void)
|
|
{
|
|
pci_unregister_driver(&sis_pci_driver);
|
|
}
|
|
|
|
module_init(sis_init);
|
|
module_exit(sis_exit);
|
|
|
|
MODULE_AUTHOR("Alan Cox");
|
|
MODULE_DESCRIPTION("SCSI low-level driver for SiS ATA");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_DEVICE_TABLE(pci, sis_pci_tbl);
|
|
MODULE_VERSION(DRV_VERSION);
|
|
|