linux/drivers/counter/Kconfig
Kamel Bouhara 106b104137 counter: Add microchip TCB capture counter
This drivers allows to use the capture mode of the Timer Counter Block
hardware block available in Microchip SoCs through the counter subsystem.

Two functions of the counter are supported for the moment: period
capture and quadrature decoder. The latter is only supported by the
SAMA5 series of SoCs.

For the period capture mode a basic setup has been chosen that will
reset the counter each time the period is actually reached. Of course
the device offers much more possibilities.

For quadrature mode, both channel 0 and 1 must be configured even if we
only capture the position (no revolution/rotation).

Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2020-07-20 13:04:40 +01:00

85 lines
2.5 KiB
Plaintext

# SPDX-License-Identifier: GPL-2.0-only
#
# Counter devices
#
menuconfig COUNTER
tristate "Counter support"
help
This enables counter device support through the Generic Counter
interface. You only need to enable this, if you also want to enable
one or more of the counter device drivers below.
if COUNTER
config 104_QUAD_8
tristate "ACCES 104-QUAD-8 driver"
depends on PC104 && X86 && IIO
select ISA_BUS_API
help
Say yes here to build support for the ACCES 104-QUAD-8 quadrature
encoder counter/interface device family (104-QUAD-8, 104-QUAD-4).
A counter's respective error flag may be cleared by performing a write
operation on the respective count value attribute. Although the
104-QUAD-8 counters have a 25-bit range, only the lower 24 bits may be
set, either directly or via the counter's preset attribute. Interrupts
are not supported by this driver.
The base port addresses for the devices may be configured via the base
array module parameter.
config STM32_TIMER_CNT
tristate "STM32 Timer encoder counter driver"
depends on MFD_STM32_TIMERS || COMPILE_TEST
help
Select this option to enable STM32 Timer quadrature encoder
and counter driver.
To compile this driver as a module, choose M here: the
module will be called stm32-timer-cnt.
config STM32_LPTIMER_CNT
tristate "STM32 LP Timer encoder counter driver"
depends on (MFD_STM32_LPTIMER || COMPILE_TEST) && IIO
help
Select this option to enable STM32 Low-Power Timer quadrature encoder
and counter driver.
To compile this driver as a module, choose M here: the
module will be called stm32-lptimer-cnt.
config TI_EQEP
tristate "TI eQEP counter driver"
depends on (SOC_AM33XX || COMPILE_TEST)
select REGMAP_MMIO
help
Select this option to enable the Texas Instruments Enhanced Quadrature
Encoder Pulse (eQEP) counter driver.
To compile this driver as a module, choose M here: the module will be
called ti-eqep.
config FTM_QUADDEC
tristate "Flex Timer Module Quadrature decoder driver"
depends on HAS_IOMEM && OF
help
Select this option to enable the Flex Timer Quadrature decoder
driver.
To compile this driver as a module, choose M here: the
module will be called ftm-quaddec.
config MICROCHIP_TCB_CAPTURE
tristate "Microchip Timer Counter Capture driver"
depends on HAS_IOMEM && OF
select REGMAP_MMIO
help
Select this option to enable the Microchip Timer Counter Block
capture driver.
To compile this driver as a module, choose M here: the
module will be called microchip-tcb-capture.
endif # COUNTER