Minki/linux
1
0
Fork 1
mirror of https://github.com/torvalds/linux.git synced 2024-11-17 17:41:44 +00:00
Code Issues Packages Projects Releases Wiki Activity
75b1d97535
linux/drivers/ide/pci/siimage.c
Bartlomiej Zolnierkiewicz 4728d546d7 ide: remove ide_dma_enable() 
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00

1068 lines
27 KiB
C
Raw Blame History

/*
* linux/drivers/ide/pci/siimage.c Version 1.12 Mar 10 2007
*
* Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat <alan@redhat.com>
* Copyright (C) 2007 MontaVista Software, Inc.
*
* May be copied or modified under the terms of the GNU General Public License
*
* Documentation for CMD680:
* http://gkernel.sourceforge.net/specs/sii/sii-0680a-v1.31.pdf.bz2
*
* Documentation for SiI 3112:
* http://gkernel.sourceforge.net/specs/sii/3112A_SiI-DS-0095-B2.pdf.bz2
*
* Errata and other documentation only available under NDA.
*
*
* FAQ Items:
* If you are using Marvell SATA-IDE adapters with Maxtor drives
* ensure the system is set up for ATA100/UDMA5 not UDMA6.
*
* If you are using WD drives with SATA bridges you must set the
* drive to "Single". "Master" will hang
*
* If you have strange problems with nVidia chipset systems please
* see the SI support documentation and update your system BIOS
* if neccessary
*
* The Dell DRAC4 has some interesting features including effectively hot
* unplugging/replugging the virtual CD interface when the DRAC is reset.
* This often causes drivers/ide/siimage to panic but is ok with the rather
* smarter code in libata.
*/
#include <linux/types.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>
#include <asm/io.h>
/**
* pdev_is_sata - check if device is SATA
* @pdev: PCI device to check
*
* Returns true if this is a SATA controller
*/
static int pdev_is_sata(struct pci_dev *pdev)
{
switch(pdev->device)
{
case PCI_DEVICE_ID_SII_3112:
case PCI_DEVICE_ID_SII_1210SA:
return 1;
case PCI_DEVICE_ID_SII_680:
return 0;
}
BUG();
return 0;
}
/**
* is_sata - check if hwif is SATA
* @hwif: interface to check
*
* Returns true if this is a SATA controller
*/
static inline int is_sata(ide_hwif_t *hwif)
{
return pdev_is_sata(hwif->pci_dev);
}
/**
* siimage_selreg - return register base
* @hwif: interface
* @r: config offset
*
* Turn a config register offset into the right address in either
* PCI space or MMIO space to access the control register in question
* Thankfully this is a configuration operation so isnt performance
* criticial.
*/
static unsigned long siimage_selreg(ide_hwif_t *hwif, int r)
{
unsigned long base = (unsigned long)hwif->hwif_data;
base += 0xA0 + r;
if(hwif->mmio)
base += (hwif->channel << 6);
else
base += (hwif->channel << 4);
return base;
}
/**
* siimage_seldev - return register base
* @hwif: interface
* @r: config offset
*
* Turn a config register offset into the right address in either
* PCI space or MMIO space to access the control register in question
* including accounting for the unit shift.
*/
static inline unsigned long siimage_seldev(ide_drive_t *drive, int r)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long base = (unsigned long)hwif->hwif_data;
base += 0xA0 + r;
if(hwif->mmio)
base += (hwif->channel << 6);
else
base += (hwif->channel << 4);
base |= drive->select.b.unit << drive->select.b.unit;
return base;
}
/**
* sil_udma_filter - compute UDMA mask
* @drive: IDE device
*
* Compute the available UDMA speeds for the device on the interface.
*
* For the CMD680 this depends on the clocking mode (scsc), for the
* SI3112 SATA controller life is a bit simpler.
*/
static u8 sil_udma_filter(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
unsigned long base = (unsigned long) hwif->hwif_data;
u8 mask = 0, scsc = 0;
if (hwif->mmio)
scsc = hwif->INB(base + 0x4A);
else
pci_read_config_byte(hwif->pci_dev, 0x8A, &scsc);
if (is_sata(hwif)) {
mask = strstr(drive->id->model, "Maxtor") ? 0x3f : 0x7f;
goto out;
}
if ((scsc & 0x30) == 0x10) /* 133 */
mask = 0x7f;
else if ((scsc & 0x30) == 0x20) /* 2xPCI */
mask = 0x7f;
else if ((scsc & 0x30) == 0x00) /* 100 */
mask = 0x3f;
else /* Disabled ? */
BUG();
out:
return mask;
}
/**
* siimage_taskfile_timing - turn timing data to a mode
* @hwif: interface to query
*
* Read the timing data for the interface and return the
* mode that is being used.
*/
static byte siimage_taskfile_timing (ide_hwif_t *hwif)
{
u16 timing = 0x328a;
unsigned long addr = siimage_selreg(hwif, 2);
if (hwif->mmio)
timing = hwif->INW(addr);
else
pci_read_config_word(hwif->pci_dev, addr, &timing);
switch (timing) {
case 0x10c1: return 4;
case 0x10c3: return 3;
case 0x1104:
case 0x1281: return 2;
case 0x2283: return 1;
case 0x328a:
default: return 0;
}
}
/**
* simmage_tuneproc - tune a drive
* @drive: drive to tune
* @mode_wanted: the target operating mode
*
* Load the timing settings for this device mode into the
* controller. If we are in PIO mode 3 or 4 turn on IORDY
* monitoring (bit 9). The TF timing is bits 31:16
*/
static void siimage_tuneproc (ide_drive_t *drive, byte mode_wanted)
{
ide_hwif_t *hwif = HWIF(drive);
u32 speedt = 0;
u16 speedp = 0;
unsigned long addr = siimage_seldev(drive, 0x04);
unsigned long tfaddr = siimage_selreg(hwif, 0x02);
/* cheat for now and use the docs */
switch (mode_wanted) {
case 4:
speedp = 0x10c1;
speedt = 0x10c1;
break;
case 3:
speedp = 0x10c3;
speedt = 0x10c3;
break;
case 2:
speedp = 0x1104;
speedt = 0x1281;
break;
case 1:
speedp = 0x2283;
speedt = 0x2283;
break;
case 0:
default:
speedp = 0x328a;
speedt = 0x328a;
break;
}
if (hwif->mmio) {
hwif->OUTW(speedp, addr);
hwif->OUTW(speedt, tfaddr);
/* Now set up IORDY */
if(mode_wanted == 3 || mode_wanted == 4)
hwif->OUTW(hwif->INW(tfaddr-2)|0x200, tfaddr-2);
else
hwif->OUTW(hwif->INW(tfaddr-2)&~0x200, tfaddr-2);
} else {
pci_write_config_word(hwif->pci_dev, addr, speedp);
pci_write_config_word(hwif->pci_dev, tfaddr, speedt);
pci_read_config_word(hwif->pci_dev, tfaddr-2, &speedp);
speedp &= ~0x200;
/* Set IORDY for mode 3 or 4 */
if(mode_wanted == 3 || mode_wanted == 4)
speedp |= 0x200;
pci_write_config_word(hwif->pci_dev, tfaddr-2, speedp);
}
}
/**
* config_siimage_chipset_for_pio - set drive timings
* @drive: drive to tune
* @speed we want
*
* Compute the best pio mode we can for a given device. Also honour
* the timings for the driver when dealing with mixed devices. Some
* of this is ugly but its all wrapped up here
*
* The SI680 can also do VDMA - we need to start using that
*
* FIXME: we use the BIOS channel timings to avoid driving the task
* files too fast at the disk. We need to compute the master/slave
* drive PIO mode properly so that we can up the speed on a hotplug
* system.
*/
static void config_siimage_chipset_for_pio (ide_drive_t *drive, byte set_speed)
{
u8 channel_timings = siimage_taskfile_timing(HWIF(drive));
u8 speed = 0, set_pio = ide_get_best_pio_mode(drive, 4, 5, NULL);
/* WARNING PIO timing mess is going to happen b/w devices, argh */
if ((channel_timings != set_pio) && (set_pio > channel_timings))
set_pio = channel_timings;
siimage_tuneproc(drive, set_pio);
speed = XFER_PIO_0 + set_pio;
if (set_speed)
(void) ide_config_drive_speed(drive, speed);
}
/**
* siimage_tune_chipset - set controller timings
* @drive: Drive to set up
* @xferspeed: speed we want to achieve
*
* Tune the SII chipset for the desired mode. If we can't achieve
* the desired mode then tune for a lower one, but ultimately
* make the thing work.
*/
static int siimage_tune_chipset (ide_drive_t *drive, byte xferspeed)
{
u8 ultra6[] = { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 };
u8 ultra5[] = { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01 };
u16 dma[] = { 0x2208, 0x10C2, 0x10C1 };
ide_hwif_t *hwif = HWIF(drive);
u16 ultra = 0, multi = 0;
u8 mode = 0, unit = drive->select.b.unit;
u8 speed = ide_rate_filter(drive, xferspeed);
unsigned long base = (unsigned long)hwif->hwif_data;
u8 scsc = 0, addr_mask = ((hwif->channel) ?
((hwif->mmio) ? 0xF4 : 0x84) :
((hwif->mmio) ? 0xB4 : 0x80));
unsigned long ma = siimage_seldev(drive, 0x08);
unsigned long ua = siimage_seldev(drive, 0x0C);
if (hwif->mmio) {
scsc = hwif->INB(base + 0x4A);
mode = hwif->INB(base + addr_mask);
multi = hwif->INW(ma);
ultra = hwif->INW(ua);
} else {
pci_read_config_byte(hwif->pci_dev, 0x8A, &scsc);
pci_read_config_byte(hwif->pci_dev, addr_mask, &mode);
pci_read_config_word(hwif->pci_dev, ma, &multi);
pci_read_config_word(hwif->pci_dev, ua, &ultra);
}
mode &= ~((unit) ? 0x30 : 0x03);
ultra &= ~0x3F;
scsc = ((scsc & 0x30) == 0x00) ? 0 : 1;
scsc = is_sata(hwif) ? 1 : scsc;
switch(speed) {
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
siimage_tuneproc(drive, (speed - XFER_PIO_0));
mode |= ((unit) ? 0x10 : 0x01);
break;
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_MW_DMA_0:
multi = dma[speed - XFER_MW_DMA_0];
mode |= ((unit) ? 0x20 : 0x02);
config_siimage_chipset_for_pio(drive, 0);
break;
case XFER_UDMA_6:
case XFER_UDMA_5:
case XFER_UDMA_4:
case XFER_UDMA_3:
case XFER_UDMA_2:
case XFER_UDMA_1:
case XFER_UDMA_0:
multi = dma[2];
ultra |= ((scsc) ? (ultra6[speed - XFER_UDMA_0]) :
(ultra5[speed - XFER_UDMA_0]));
mode |= ((unit) ? 0x30 : 0x03);
config_siimage_chipset_for_pio(drive, 0);
break;
default:
return 1;
}
if (hwif->mmio) {
hwif->OUTB(mode, base + addr_mask);
hwif->OUTW(multi, ma);
hwif->OUTW(ultra, ua);
} else {
pci_write_config_byte(hwif->pci_dev, addr_mask, mode);
pci_write_config_word(hwif->pci_dev, ma, multi);
pci_write_config_word(hwif->pci_dev, ua, ultra);
}
return (ide_config_drive_speed(drive, speed));
}
/**
* siimage_configure_drive_for_dma - set up for DMA transfers
* @drive: drive we are going to set up
*
* Set up the drive for DMA, tune the controller and drive as
* required. If the drive isn't suitable for DMA or we hit
* other problems then we will drop down to PIO and set up
* PIO appropriately
*/
static int siimage_config_drive_for_dma (ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
config_siimage_chipset_for_pio(drive, 1);
return -1;
}
/* returns 1 if dma irq issued, 0 otherwise */
static int siimage_io_ide_dma_test_irq (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
u8 dma_altstat = 0;
unsigned long addr = siimage_selreg(hwif, 1);
/* return 1 if INTR asserted */
if ((hwif->INB(hwif->dma_status) & 4) == 4)
return 1;
/* return 1 if Device INTR asserted */
pci_read_config_byte(hwif->pci_dev, addr, &dma_altstat);
if (dma_altstat & 8)
return 0; //return 1;
return 0;
}
/**
* siimage_mmio_ide_dma_test_irq - check we caused an IRQ
* @drive: drive we are testing
*
* Check if we caused an IDE DMA interrupt. We may also have caused
* SATA status interrupts, if so we clean them up and continue.
*/
static int siimage_mmio_ide_dma_test_irq (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long base = (unsigned long)hwif->hwif_data;
unsigned long addr = siimage_selreg(hwif, 0x1);
if (SATA_ERROR_REG) {
u32 ext_stat = readl((void __iomem *)(base + 0x10));
u8 watchdog = 0;
if (ext_stat & ((hwif->channel) ? 0x40 : 0x10)) {
u32 sata_error = readl((void __iomem *)SATA_ERROR_REG);
writel(sata_error, (void __iomem *)SATA_ERROR_REG);
watchdog = (sata_error & 0x00680000) ? 1 : 0;
printk(KERN_WARNING "%s: sata_error = 0x%08x, "
"watchdog = %d, %s\n",
drive->name, sata_error, watchdog,
__FUNCTION__);
} else {
watchdog = (ext_stat & 0x8000) ? 1 : 0;
}
ext_stat >>= 16;
if (!(ext_stat & 0x0404) && !watchdog)
return 0;
}
/* return 1 if INTR asserted */
if ((readb((void __iomem *)hwif->dma_status) & 0x04) == 0x04)
return 1;
/* return 1 if Device INTR asserted */
if ((readb((void __iomem *)addr) & 8) == 8)
return 0; //return 1;
return 0;
}
/**
* siimage_busproc - bus isolation ioctl
* @drive: drive to isolate/restore
* @state: bus state to set
*
* Used by the SII3112 to handle bus isolation. As this is a
* SATA controller the work required is quite limited, we
* just have to clean up the statistics
*/
static int siimage_busproc (ide_drive_t * drive, int state)
{
ide_hwif_t *hwif = HWIF(drive);
u32 stat_config = 0;
unsigned long addr = siimage_selreg(hwif, 0);
if (hwif->mmio)
stat_config = readl((void __iomem *)addr);
else
pci_read_config_dword(hwif->pci_dev, addr, &stat_config);
switch (state) {
case BUSSTATE_ON:
hwif->drives[0].failures = 0;
hwif->drives[1].failures = 0;
break;
case BUSSTATE_OFF:
hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
break;
case BUSSTATE_TRISTATE:
hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
break;
default:
return -EINVAL;
}
hwif->bus_state = state;
return 0;
}
/**
* siimage_reset_poll - wait for sata reset
* @drive: drive we are resetting
*
* Poll the SATA phy and see whether it has come back from the dead
* yet.
*/
static int siimage_reset_poll (ide_drive_t *drive)
{
if (SATA_STATUS_REG) {
ide_hwif_t *hwif = HWIF(drive);
/* SATA_STATUS_REG is valid only when in MMIO mode */
if ((readl((void __iomem *)SATA_STATUS_REG) & 0x03) != 0x03) {
printk(KERN_WARNING "%s: reset phy dead, status=0x%08x\n",
hwif->name, readl((void __iomem *)SATA_STATUS_REG));
HWGROUP(drive)->polling = 0;
return ide_started;
}
return 0;
} else {
return 0;
}
}
/**
* siimage_pre_reset - reset hook
* @drive: IDE device being reset
*
* For the SATA devices we need to handle recalibration/geometry
* differently
*/
static void siimage_pre_reset (ide_drive_t *drive)
{
if (drive->media != ide_disk)
return;
if (is_sata(HWIF(drive)))
{
drive->special.b.set_geometry = 0;
drive->special.b.recalibrate = 0;
}
}
/**
* siimage_reset - reset a device on an siimage controller
* @drive: drive to reset
*
* Perform a controller level reset fo the device. For
* SATA we must also check the PHY.
*/
static void siimage_reset (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
u8 reset = 0;
unsigned long addr = siimage_selreg(hwif, 0);
if (hwif->mmio) {
reset = hwif->INB(addr);
hwif->OUTB((reset|0x03), addr);
/* FIXME:posting */
udelay(25);
hwif->OUTB(reset, addr);
(void) hwif->INB(addr);
} else {
pci_read_config_byte(hwif->pci_dev, addr, &reset);
pci_write_config_byte(hwif->pci_dev, addr, reset|0x03);
udelay(25);
pci_write_config_byte(hwif->pci_dev, addr, reset);
pci_read_config_byte(hwif->pci_dev, addr, &reset);
}
if (SATA_STATUS_REG) {
/* SATA_STATUS_REG is valid only when in MMIO mode */
u32 sata_stat = readl((void __iomem *)SATA_STATUS_REG);
printk(KERN_WARNING "%s: reset phy, status=0x%08x, %s\n",
hwif->name, sata_stat, __FUNCTION__);
if (!(sata_stat)) {
printk(KERN_WARNING "%s: reset phy dead, status=0x%08x\n",
hwif->name, sata_stat);
drive->failures++;
}
}
}
/**
* proc_reports_siimage - add siimage controller to proc
* @dev: PCI device
* @clocking: SCSC value
* @name: controller name
*
* Report the clocking mode of the controller and add it to
* the /proc interface layer
*/
static void proc_reports_siimage (struct pci_dev *dev, u8 clocking, const char *name)
{
if (!pdev_is_sata(dev)) {
printk(KERN_INFO "%s: BASE CLOCK ", name);
clocking &= 0x03;
switch (clocking) {
case 0x03: printk("DISABLED!\n"); break;
case 0x02: printk("== 2X PCI\n"); break;
case 0x01: printk("== 133\n"); break;
case 0x00: printk("== 100\n"); break;
}
}
}
/**
* setup_mmio_siimage - switch an SI controller into MMIO
* @dev: PCI device we are configuring
* @name: device name
*
* Attempt to put the device into mmio mode. There are some slight
* complications here with certain systems where the mmio bar isnt
* mapped so we have to be sure we can fall back to I/O.
*/
static unsigned int setup_mmio_siimage (struct pci_dev *dev, const char *name)
{
unsigned long bar5 = pci_resource_start(dev, 5);
unsigned long barsize = pci_resource_len(dev, 5);
u8 tmpbyte = 0;
void __iomem *ioaddr;
u32 tmp, irq_mask;
/*
* Drop back to PIO if we can't map the mmio. Some
* systems seem to get terminally confused in the PCI
* spaces.
*/
if(!request_mem_region(bar5, barsize, name))
{
printk(KERN_WARNING "siimage: IDE controller MMIO ports not available.\n");
return 0;
}
ioaddr = ioremap(bar5, barsize);
if (ioaddr == NULL)
{
release_mem_region(bar5, barsize);
return 0;
}
pci_set_master(dev);
pci_set_drvdata(dev, (void *) ioaddr);
if (pdev_is_sata(dev)) {
/* make sure IDE0/1 interrupts are not masked */
irq_mask = (1 << 22) | (1 << 23);
tmp = readl(ioaddr + 0x48);
if (tmp & irq_mask) {
tmp &= ~irq_mask;
writel(tmp, ioaddr + 0x48);
readl(ioaddr + 0x48); /* flush */
}
writel(0, ioaddr + 0x148);
writel(0, ioaddr + 0x1C8);
}
writeb(0, ioaddr + 0xB4);
writeb(0, ioaddr + 0xF4);
tmpbyte = readb(ioaddr + 0x4A);
switch(tmpbyte & 0x30) {
case 0x00:
/* In 100 MHz clocking, try and switch to 133 */
writeb(tmpbyte|0x10, ioaddr + 0x4A);
break;
case 0x10:
/* On 133Mhz clocking */
break;
case 0x20:
/* On PCIx2 clocking */
break;
case 0x30:
/* Clocking is disabled */
/* 133 clock attempt to force it on */
writeb(tmpbyte & ~0x20, ioaddr + 0x4A);
break;
}
writeb( 0x72, ioaddr + 0xA1);
writew( 0x328A, ioaddr + 0xA2);
writel(0x62DD62DD, ioaddr + 0xA4);
writel(0x43924392, ioaddr + 0xA8);
writel(0x40094009, ioaddr + 0xAC);
writeb( 0x72, ioaddr + 0xE1);
writew( 0x328A, ioaddr + 0xE2);
writel(0x62DD62DD, ioaddr + 0xE4);
writel(0x43924392, ioaddr + 0xE8);
writel(0x40094009, ioaddr + 0xEC);
if (pdev_is_sata(dev)) {
writel(0xFFFF0000, ioaddr + 0x108);
writel(0xFFFF0000, ioaddr + 0x188);
writel(0x00680000, ioaddr + 0x148);
writel(0x00680000, ioaddr + 0x1C8);
}
tmpbyte = readb(ioaddr + 0x4A);
proc_reports_siimage(dev, (tmpbyte>>4), name);
return 1;
}
/**
* init_chipset_siimage - set up an SI device
* @dev: PCI device
* @name: device name
*
* Perform the initial PCI set up for this device. Attempt to switch
* to 133MHz clocking if the system isn't already set up to do it.
*/
static unsigned int __devinit init_chipset_siimage(struct pci_dev *dev, const char *name)
{
u32 class_rev = 0;
u8 tmpbyte = 0;
u8 BA5_EN = 0;
pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
class_rev &= 0xff;
pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (class_rev) ? 1 : 255);
pci_read_config_byte(dev, 0x8A, &BA5_EN);
if ((BA5_EN & 0x01) || (pci_resource_start(dev, 5))) {
if (setup_mmio_siimage(dev, name)) {
return 0;
}
}
pci_write_config_byte(dev, 0x80, 0x00);
pci_write_config_byte(dev, 0x84, 0x00);
pci_read_config_byte(dev, 0x8A, &tmpbyte);
switch(tmpbyte & 0x30) {
case 0x00:
/* 133 clock attempt to force it on */
pci_write_config_byte(dev, 0x8A, tmpbyte|0x10);
case 0x30:
/* if clocking is disabled */
/* 133 clock attempt to force it on */
pci_write_config_byte(dev, 0x8A, tmpbyte & ~0x20);
case 0x10:
/* 133 already */
break;
case 0x20:
/* BIOS set PCI x2 clocking */
break;
}
pci_read_config_byte(dev, 0x8A, &tmpbyte);
pci_write_config_byte(dev, 0xA1, 0x72);
pci_write_config_word(dev, 0xA2, 0x328A);
pci_write_config_dword(dev, 0xA4, 0x62DD62DD);
pci_write_config_dword(dev, 0xA8, 0x43924392);
pci_write_config_dword(dev, 0xAC, 0x40094009);
pci_write_config_byte(dev, 0xB1, 0x72);
pci_write_config_word(dev, 0xB2, 0x328A);
pci_write_config_dword(dev, 0xB4, 0x62DD62DD);
pci_write_config_dword(dev, 0xB8, 0x43924392);
pci_write_config_dword(dev, 0xBC, 0x40094009);
proc_reports_siimage(dev, (tmpbyte>>4), name);
return 0;
}
/**
* init_mmio_iops_siimage - set up the iops for MMIO
* @hwif: interface to set up
*
* The basic setup here is fairly simple, we can use standard MMIO
* operations. However we do have to set the taskfile register offsets
* by hand as there isnt a standard defined layout for them this
* time.
*
* The hardware supports buffered taskfiles and also some rather nice
* extended PRD tables. For better SI3112 support use the libata driver
*/
static void __devinit init_mmio_iops_siimage(ide_hwif_t *hwif)
{
struct pci_dev *dev = hwif->pci_dev;
void *addr = pci_get_drvdata(dev);
u8 ch = hwif->channel;
hw_regs_t hw;
unsigned long base;
/*
* Fill in the basic HWIF bits
*/
default_hwif_mmiops(hwif);
hwif->hwif_data = addr;
/*
* Now set up the hw. We have to do this ourselves as
* the MMIO layout isnt the same as the standard port
* based I/O
*/
memset(&hw, 0, sizeof(hw_regs_t));
base = (unsigned long)addr;
if (ch)
base += 0xC0;
else
base += 0x80;
/*
* The buffered task file doesn't have status/control
* so we can't currently use it sanely since we want to
* use LBA48 mode.
*/
hw.io_ports[IDE_DATA_OFFSET] = base;
hw.io_ports[IDE_ERROR_OFFSET] = base + 1;
hw.io_ports[IDE_NSECTOR_OFFSET] = base + 2;
hw.io_ports[IDE_SECTOR_OFFSET] = base + 3;
hw.io_ports[IDE_LCYL_OFFSET] = base + 4;
hw.io_ports[IDE_HCYL_OFFSET] = base + 5;
hw.io_ports[IDE_SELECT_OFFSET] = base + 6;
hw.io_ports[IDE_STATUS_OFFSET] = base + 7;
hw.io_ports[IDE_CONTROL_OFFSET] = base + 10;
hw.io_ports[IDE_IRQ_OFFSET] = 0;
if (pdev_is_sata(dev)) {
base = (unsigned long)addr;
if (ch)
base += 0x80;
hwif->sata_scr[SATA_STATUS_OFFSET] = base + 0x104;
hwif->sata_scr[SATA_ERROR_OFFSET] = base + 0x108;
hwif->sata_scr[SATA_CONTROL_OFFSET] = base + 0x100;
hwif->sata_misc[SATA_MISC_OFFSET] = base + 0x140;
hwif->sata_misc[SATA_PHY_OFFSET] = base + 0x144;
hwif->sata_misc[SATA_IEN_OFFSET] = base + 0x148;
}
hw.irq = hwif->pci_dev->irq;
memcpy(&hwif->hw, &hw, sizeof(hw));
memcpy(hwif->io_ports, hwif->hw.io_ports, sizeof(hwif->hw.io_ports));
hwif->irq = hw.irq;
base = (unsigned long) addr;
hwif->dma_base = base + (ch ? 0x08 : 0x00);
hwif->mmio = 1;
}
static int is_dev_seagate_sata(ide_drive_t *drive)
{
const char *s = &drive->id->model[0];
unsigned len;
if (!drive->present)
return 0;
len = strnlen(s, sizeof(drive->id->model));
if ((len > 4) && (!memcmp(s, "ST", 2))) {
if ((!memcmp(s + len - 2, "AS", 2)) ||
(!memcmp(s + len - 3, "ASL", 3))) {
printk(KERN_INFO "%s: applying pessimistic Seagate "
"errata fix\n", drive->name);
return 1;
}
}
return 0;
}
/**
* siimage_fixup - post probe fixups
* @hwif: interface to fix up
*
* Called after drive probe we use this to decide whether the
* Seagate fixup must be applied. This used to be in init_iops but
* that can occur before we know what drives are present.
*/
static void __devinit siimage_fixup(ide_hwif_t *hwif)
{
/* Try and raise the rqsize */
if (!is_sata(hwif) || !is_dev_seagate_sata(&hwif->drives[0]))
hwif->rqsize = 128;
}
/**
* init_iops_siimage - set up iops
* @hwif: interface to set up
*
* Do the basic setup for the SIIMAGE hardware interface
* and then do the MMIO setup if we can. This is the first
* look in we get for setting up the hwif so that we
* can get the iops right before using them.
*/
static void __devinit init_iops_siimage(ide_hwif_t *hwif)
{
struct pci_dev *dev = hwif->pci_dev;
u32 class_rev = 0;
pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
class_rev &= 0xff;
hwif->hwif_data = NULL;
/* Pessimal until we finish probing */
hwif->rqsize = 15;
if (pci_get_drvdata(dev) == NULL)
return;
init_mmio_iops_siimage(hwif);
}
/**
* ata66_siimage - check for 80 pin cable
* @hwif: interface to check
*
* Check for the presence of an ATA66 capable cable on the
* interface.
*/
static unsigned int __devinit ata66_siimage(ide_hwif_t *hwif)
{
unsigned long addr = siimage_selreg(hwif, 0);
if (pci_get_drvdata(hwif->pci_dev) == NULL) {
u8 ata66 = 0;
pci_read_config_byte(hwif->pci_dev, addr, &ata66);
return (ata66 & 0x01) ? 1 : 0;
}
return (hwif->INB(addr) & 0x01) ? 1 : 0;
}
/**
* init_hwif_siimage - set up hwif structs
* @hwif: interface to set up
*
* We do the basic set up of the interface structure. The SIIMAGE
* requires several custom handlers so we override the default
* ide DMA handlers appropriately
*/
static void __devinit init_hwif_siimage(ide_hwif_t *hwif)
{
hwif->autodma = 0;
hwif->resetproc = &siimage_reset;
hwif->speedproc = &siimage_tune_chipset;
hwif->tuneproc = &siimage_tuneproc;
hwif->reset_poll = &siimage_reset_poll;
hwif->pre_reset = &siimage_pre_reset;
hwif->udma_filter = &sil_udma_filter;
if(is_sata(hwif)) {
static int first = 1;
hwif->busproc = &siimage_busproc;
if (first) {
printk(KERN_INFO "siimage: For full SATA support you should use the libata sata_sil module.\n");
first = 0;
}
}
if (!hwif->dma_base) {
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
return;
}
hwif->ultra_mask = 0x7f;
hwif->mwdma_mask = 0x07;
if (!is_sata(hwif))
hwif->atapi_dma = 1;
hwif->ide_dma_check = &siimage_config_drive_for_dma;
if (!(hwif->udma_four))
hwif->udma_four = ata66_siimage(hwif);
if (hwif->mmio) {
hwif->ide_dma_test_irq = &siimage_mmio_ide_dma_test_irq;
} else {
hwif->ide_dma_test_irq = & siimage_io_ide_dma_test_irq;
}
/*
* The BIOS often doesn't set up DMA on this controller
* so we always do it.
*/
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
#define DECLARE_SII_DEV(name_str) \
{ \
.name = name_str, \
.init_chipset = init_chipset_siimage, \
.init_iops = init_iops_siimage, \
.init_hwif = init_hwif_siimage, \
.fixup = siimage_fixup, \
.channels = 2, \
.autodma = AUTODMA, \
.bootable = ON_BOARD, \
}
static ide_pci_device_t siimage_chipsets[] __devinitdata = {
/* 0 */ DECLARE_SII_DEV("SiI680"),
/* 1 */ DECLARE_SII_DEV("SiI3112 Serial ATA"),
/* 2 */ DECLARE_SII_DEV("Adaptec AAR-1210SA")
};
/**
* siimage_init_one - pci layer discovery entry
* @dev: PCI device
* @id: ident table entry
*
* Called by the PCI code when it finds an SI680 or SI3112 controller.
* We then use the IDE PCI generic helper to do most of the work.
*/
static int __devinit siimage_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
return ide_setup_pci_device(dev, &siimage_chipsets[id->driver_data]);
}
static struct pci_device_id siimage_pci_tbl[] = {
{ PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
#ifdef CONFIG_BLK_DEV_IDE_SATA
{ PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_1210SA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
#endif
{ 0, },
};
MODULE_DEVICE_TABLE(pci, siimage_pci_tbl);
static struct pci_driver driver = {
.name = "SiI_IDE",
.id_table = siimage_pci_tbl,
.probe = siimage_init_one,
};
static int __init siimage_ide_init(void)
{
return ide_pci_register_driver(&driver);
}
module_init(siimage_ide_init);
MODULE_AUTHOR("Andre Hedrick, Alan Cox");
MODULE_DESCRIPTION("PCI driver module for SiI IDE");
MODULE_LICENSE("GPL");
Reference in New Issue View Git Blame Copy Permalink