mirror of
https://github.com/torvalds/linux.git
synced 2024-11-20 02:51:44 +00:00
658628e7ef
Add controller driver for QCOM SoCs that have hardware based shared resource management. The hardware IP known as RSC (Resource State Coordinator) houses multiple Direct Resource Voter (DRV) for different execution levels. A DRV is a unique voter on the state of a shared resource. A Trigger Control Set (TCS) is a bunch of slots that can house multiple resource state requests, that when triggered will issue those requests through an internal bus to the Resource Power Manager Hardened (RPMH) blocks. These hardware blocks are capable of adjusting clocks, voltages, etc. The resource state request from a DRV are aggregated along with state requests from other processors in the SoC and the aggregate value is applied on the resource. Some important aspects of the RPMH communication - - Requests are <addr, value> with some header information - Multiple requests (upto 16) may be sent through a TCS, at a time - Requests in a TCS are sent in sequence - Requests may be fire-n-forget or completion (response expected) - Multiple TCS from the same DRV may be triggered simultaneously - Cannot send a request if another request for the same addr is in progress from the same DRV - When all the requests from a TCS are complete, an IRQ is raised - The IRQ handler needs to clear the TCS before it is available for reuse - TCS configuration is specific to a DRV - Platform drivers may use DRV from different RSCs to make requests Resource state requests made when CPUs are active are called 'active' state requests. Requests made when all the CPUs are powered down (idle state) are called 'sleep' state requests. They are matched by a corresponding 'wake' state requests which puts the resources back in to previously requested active state before resuming any CPU. TCSes are dedicated for each type of requests. Active mode TCSes (AMC) are used to send requests immediately to the resource, while control TCS are used to provide specific information to the controller. Sleep and Wake TCS send sleep and wake requests, after and before the system halt respectively. Signed-off-by: Lina Iyer <ilina@codeaurora.org> Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
57 lines
1.5 KiB
C
57 lines
1.5 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
/*
|
|
* Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
|
|
*/
|
|
|
|
#ifndef __SOC_QCOM_TCS_H__
|
|
#define __SOC_QCOM_TCS_H__
|
|
|
|
#define MAX_RPMH_PAYLOAD 16
|
|
|
|
/**
|
|
* rpmh_state: state for the request
|
|
*
|
|
* RPMH_SLEEP_STATE: State of the resource when the processor subsystem
|
|
* is powered down. There is no client using the
|
|
* resource actively.
|
|
* RPMH_WAKE_ONLY_STATE: Resume resource state to the value previously
|
|
* requested before the processor was powered down.
|
|
* RPMH_ACTIVE_ONLY_STATE: Active or AMC mode requests. Resource state
|
|
* is aggregated immediately.
|
|
*/
|
|
enum rpmh_state {
|
|
RPMH_SLEEP_STATE,
|
|
RPMH_WAKE_ONLY_STATE,
|
|
RPMH_ACTIVE_ONLY_STATE,
|
|
};
|
|
|
|
/**
|
|
* struct tcs_cmd: an individual request to RPMH.
|
|
*
|
|
* @addr: the address of the resource slv_id:18:16 | offset:0:15
|
|
* @data: the resource state request
|
|
* @wait: wait for this request to be complete before sending the next
|
|
*/
|
|
struct tcs_cmd {
|
|
u32 addr;
|
|
u32 data;
|
|
u32 wait;
|
|
};
|
|
|
|
/**
|
|
* struct tcs_request: A set of tcs_cmds sent together in a TCS
|
|
*
|
|
* @state: state for the request.
|
|
* @wait_for_compl: wait until we get a response from the h/w accelerator
|
|
* @num_cmds: the number of @cmds in this request
|
|
* @cmds: an array of tcs_cmds
|
|
*/
|
|
struct tcs_request {
|
|
enum rpmh_state state;
|
|
u32 wait_for_compl;
|
|
u32 num_cmds;
|
|
struct tcs_cmd *cmds;
|
|
};
|
|
|
|
#endif /* __SOC_QCOM_TCS_H__ */
|