linux/arch/arm/mach-omap1/board-palmte.c
Tony Lindgren 652bcd8f72 omap mmc: Remove broken MMC init code
Most of the omap1 MMC boards got broken by an earlier patch
138ab9f832. If you look closely,
the MMC init funtions are pretty much just stubs.

Remove broken init code to make room for cleaner MMC init code.

Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-12-10 17:37:16 -08:00

390 lines
9.7 KiB
C

/*
* linux/arch/arm/mach-omap1/board-palmte.c
*
* Modified from board-generic.c
*
* Support for the Palm Tungsten E PDA.
*
* Original version : Laurent Gonzalez
*
* Maintainers : http://palmtelinux.sf.net
* palmtelinux-developpers@lists.sf.net
*
* Copyright (c) 2006 Andrzej Zaborowski <balrog@zabor.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/input.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/interrupt.h>
#include <linux/apm-emulation.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
#include <mach/gpio.h>
#include <mach/mux.h>
#include <mach/usb.h>
#include <mach/tc.h>
#include <mach/dma.h>
#include <mach/board.h>
#include <mach/irda.h>
#include <mach/keypad.h>
#include <mach/common.h>
#include <mach/mcbsp.h>
#include <mach/omap-alsa.h>
static void __init omap_palmte_init_irq(void)
{
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
}
static const int palmte_keymap[] = {
KEY(0, 0, KEY_F1), /* Calendar */
KEY(0, 1, KEY_F2), /* Contacts */
KEY(0, 2, KEY_F3), /* Tasks List */
KEY(0, 3, KEY_F4), /* Note Pad */
KEY(0, 4, KEY_POWER),
KEY(1, 0, KEY_LEFT),
KEY(1, 1, KEY_DOWN),
KEY(1, 2, KEY_UP),
KEY(1, 3, KEY_RIGHT),
KEY(1, 4, KEY_ENTER),
0,
};
static struct omap_kp_platform_data palmte_kp_data = {
.rows = 8,
.cols = 8,
.keymap = (int *) palmte_keymap,
.rep = 1,
.delay = 12,
};
static struct resource palmte_kp_resources[] = {
[0] = {
.start = INT_KEYBOARD,
.end = INT_KEYBOARD,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device palmte_kp_device = {
.name = "omap-keypad",
.id = -1,
.dev = {
.platform_data = &palmte_kp_data,
},
.num_resources = ARRAY_SIZE(palmte_kp_resources),
.resource = palmte_kp_resources,
};
static struct mtd_partition palmte_rom_partitions[] = {
/* PalmOS "Small ROM", contains the bootloader and the debugger */
{
.name = "smallrom",
.offset = 0,
.size = 0xa000,
.mask_flags = MTD_WRITEABLE,
},
/* PalmOS "Big ROM", a filesystem with all the OS code and data */
{
.name = "bigrom",
.offset = SZ_128K,
/*
* 0x5f0000 bytes big in the multi-language ("EFIGS") version,
* 0x7b0000 bytes in the English-only ("enUS") version.
*/
.size = 0x7b0000,
.mask_flags = MTD_WRITEABLE,
},
};
static struct flash_platform_data palmte_rom_data = {
.map_name = "map_rom",
.width = 2,
.parts = palmte_rom_partitions,
.nr_parts = ARRAY_SIZE(palmte_rom_partitions),
};
static struct resource palmte_rom_resource = {
.start = OMAP_CS0_PHYS,
.end = OMAP_CS0_PHYS + SZ_8M - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device palmte_rom_device = {
.name = "omapflash",
.id = -1,
.dev = {
.platform_data = &palmte_rom_data,
},
.num_resources = 1,
.resource = &palmte_rom_resource,
};
static struct platform_device palmte_lcd_device = {
.name = "lcd_palmte",
.id = -1,
};
static struct omap_backlight_config palmte_backlight_config = {
.default_intensity = 0xa0,
};
static struct platform_device palmte_backlight_device = {
.name = "omap-bl",
.id = -1,
.dev = {
.platform_data = &palmte_backlight_config,
},
};
static struct omap_irda_config palmte_irda_config = {
.transceiver_cap = IR_SIRMODE,
.rx_channel = OMAP_DMA_UART3_RX,
.tx_channel = OMAP_DMA_UART3_TX,
.dest_start = UART3_THR,
.src_start = UART3_RHR,
.tx_trigger = 0,
.rx_trigger = 0,
};
static struct resource palmte_irda_resources[] = {
[0] = {
.start = INT_UART3,
.end = INT_UART3,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device palmte_irda_device = {
.name = "omapirda",
.id = -1,
.dev = {
.platform_data = &palmte_irda_config,
},
.num_resources = ARRAY_SIZE(palmte_irda_resources),
.resource = palmte_irda_resources,
};
static struct platform_device *palmte_devices[] __initdata = {
&palmte_rom_device,
&palmte_kp_device,
&palmte_lcd_device,
&palmte_backlight_device,
&palmte_irda_device,
};
static struct omap_usb_config palmte_usb_config __initdata = {
.register_dev = 1, /* Mini-B only receptacle */
.hmc_mode = 0,
.pins[0] = 2,
};
static struct omap_mmc_config palmte_mmc_config __initdata = {
.mmc[0] = {
.enabled = 1,
.wp_pin = PALMTE_MMC_WP_GPIO,
.power_pin = PALMTE_MMC_POWER_GPIO,
.switch_pin = PALMTE_MMC_SWITCH_GPIO,
},
};
static struct omap_lcd_config palmte_lcd_config __initdata = {
.ctrl_name = "internal",
};
static struct omap_uart_config palmte_uart_config __initdata = {
.enabled_uarts = (1 << 0) | (1 << 1) | (0 << 2),
};
static struct omap_mcbsp_reg_cfg palmte_mcbsp1_regs = {
.spcr2 = FRST | GRST | XRST | XINTM(3),
.xcr2 = XDATDLY(1) | XFIG,
.xcr1 = XWDLEN1(OMAP_MCBSP_WORD_32),
.pcr0 = SCLKME | FSXP | CLKXP,
};
static struct omap_alsa_codec_config palmte_alsa_config = {
.name = "TSC2102 audio",
.mcbsp_regs_alsa = &palmte_mcbsp1_regs,
.codec_configure_dev = NULL, /* tsc2102_configure, */
.codec_set_samplerate = NULL, /* tsc2102_set_samplerate, */
.codec_clock_setup = NULL, /* tsc2102_clock_setup, */
.codec_clock_on = NULL, /* tsc2102_clock_on, */
.codec_clock_off = NULL, /* tsc2102_clock_off, */
.get_default_samplerate = NULL, /* tsc2102_get_default_samplerate, */
};
#ifdef CONFIG_APM
/*
* Values measured in 10 minute intervals averaged over 10 samples.
* May differ slightly from device to device but should be accurate
* enough to give basic idea of battery life left and trigger
* potential alerts.
*/
static const int palmte_battery_sample[] = {
2194, 2157, 2138, 2120,
2104, 2089, 2075, 2061,
2048, 2038, 2026, 2016,
2008, 1998, 1989, 1980,
1970, 1958, 1945, 1928,
1910, 1888, 1860, 1827,
1791, 1751, 1709, 1656,
};
#define INTERVAL 10
#define BATTERY_HIGH_TRESHOLD 66
#define BATTERY_LOW_TRESHOLD 33
static void palmte_get_power_status(struct apm_power_info *info, int *battery)
{
int charging, batt, hi, lo, mid;
charging = !gpio_get_value(PALMTE_DC_GPIO);
batt = battery[0];
if (charging)
batt -= 60;
hi = ARRAY_SIZE(palmte_battery_sample);
lo = 0;
info->battery_flag = 0;
info->units = APM_UNITS_MINS;
if (batt > palmte_battery_sample[lo]) {
info->battery_life = 100;
info->time = INTERVAL * ARRAY_SIZE(palmte_battery_sample);
} else if (batt <= palmte_battery_sample[hi - 1]) {
info->battery_life = 0;
info->time = 0;
} else {
while (hi > lo + 1) {
mid = (hi + lo) >> 1;
if (batt <= palmte_battery_sample[mid])
lo = mid;
else
hi = mid;
}
mid = palmte_battery_sample[lo] - palmte_battery_sample[hi];
hi = palmte_battery_sample[lo] - batt;
info->battery_life = 100 - (100 * lo + 100 * hi / mid) /
ARRAY_SIZE(palmte_battery_sample);
info->time = INTERVAL * (ARRAY_SIZE(palmte_battery_sample) -
lo) - INTERVAL * hi / mid;
}
if (charging) {
info->ac_line_status = APM_AC_ONLINE;
info->battery_status = APM_BATTERY_STATUS_CHARGING;
info->battery_flag |= APM_BATTERY_FLAG_CHARGING;
} else {
info->ac_line_status = APM_AC_OFFLINE;
if (info->battery_life > BATTERY_HIGH_TRESHOLD)
info->battery_status = APM_BATTERY_STATUS_HIGH;
else if (info->battery_life > BATTERY_LOW_TRESHOLD)
info->battery_status = APM_BATTERY_STATUS_LOW;
else
info->battery_status = APM_BATTERY_STATUS_CRITICAL;
}
if (info->battery_life > BATTERY_HIGH_TRESHOLD)
info->battery_flag |= APM_BATTERY_FLAG_HIGH;
else if (info->battery_life > BATTERY_LOW_TRESHOLD)
info->battery_flag |= APM_BATTERY_FLAG_LOW;
else
info->battery_flag |= APM_BATTERY_FLAG_CRITICAL;
}
#else
#define palmte_get_power_status NULL
#endif
static struct omap_board_config_kernel palmte_config[] __initdata = {
{ OMAP_TAG_USB, &palmte_usb_config },
{ OMAP_TAG_LCD, &palmte_lcd_config },
{ OMAP_TAG_UART, &palmte_uart_config },
};
static struct spi_board_info palmte_spi_info[] __initdata = {
{
.modalias = "tsc2102",
.bus_num = 2, /* uWire (officially) */
.chip_select = 0, /* As opposed to 3 */
.irq = OMAP_GPIO_IRQ(PALMTE_PINTDAV_GPIO),
.max_speed_hz = 8000000,
},
};
static void palmte_headphones_detect(void *data, int state)
{
if (state) {
/* Headphones connected, disable speaker */
gpio_set_value(PALMTE_SPEAKER_GPIO, 0);
printk(KERN_INFO "PM: speaker off\n");
} else {
/* Headphones unplugged, re-enable speaker */
gpio_set_value(PALMTE_SPEAKER_GPIO, 1);
printk(KERN_INFO "PM: speaker on\n");
}
}
static void __init palmte_misc_gpio_setup(void)
{
/* Set TSC2102 PINTDAV pin as input (used by TSC2102 driver) */
if (gpio_request(PALMTE_PINTDAV_GPIO, "TSC2102 PINTDAV") < 0) {
printk(KERN_ERR "Could not reserve PINTDAV GPIO!\n");
return;
}
gpio_direction_input(PALMTE_PINTDAV_GPIO);
/* Set USB-or-DC-IN pin as input (unused) */
if (gpio_request(PALMTE_USB_OR_DC_GPIO, "USB/DC-IN") < 0) {
printk(KERN_ERR "Could not reserve cable signal GPIO!\n");
return;
}
gpio_direction_input(PALMTE_USB_OR_DC_GPIO);
}
static void __init omap_palmte_init(void)
{
omap_board_config = palmte_config;
omap_board_config_size = ARRAY_SIZE(palmte_config);
platform_add_devices(palmte_devices, ARRAY_SIZE(palmte_devices));
spi_register_board_info(palmte_spi_info, ARRAY_SIZE(palmte_spi_info));
palmte_misc_gpio_setup();
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
}
static void __init omap_palmte_map_io(void)
{
omap1_map_common_io();
}
MACHINE_START(OMAP_PALMTE, "OMAP310 based Palm Tungsten E")
.phys_io = 0xfff00000,
.io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
.boot_params = 0x10000100,
.map_io = omap_palmte_map_io,
.init_irq = omap_palmte_init_irq,
.init_machine = omap_palmte_init,
.timer = &omap_timer,
MACHINE_END