linux/drivers/mmc/host/sdhci-xenon.c
Elad Nachman 5d40213347 mmc: xenon: Add ac5 support via bounce buffer
AC5/X/IM SOCs has a variant of the Xenon eMMC controller,
in which only 31-bit of addressing pass from the controller
on the AXI bus.
Since we cannot guarantee that only buffers from the first 2GB
of memory will reach the driver, the driver is configured for
SDMA mode, without 64-bit mode, overriding the DMA mask to 34-bit
to support the DDR memory mapping, which starts at offset 8GB.

Signed-off-by: Elad Nachman <enachman@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240104173033.2836110-1-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2024-01-05 11:03:56 +01:00

745 lines
20 KiB
C

// SPDX-License-Identifier: GPL-2.0-only
/*
* Driver for Marvell Xenon SDHC as a platform device
*
* Copyright (C) 2016 Marvell, All Rights Reserved.
*
* Author: Hu Ziji <huziji@marvell.com>
* Date: 2016-8-24
*
* Inspired by Jisheng Zhang <jszhang@marvell.com>
* Special thanks to Video BG4 project team.
*/
#include <linux/acpi.h>
#include <linux/delay.h>
#include <linux/ktime.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/pm.h>
#include <linux/pm_runtime.h>
#include <linux/mm.h>
#include <linux/dma-mapping.h>
#include "sdhci-pltfm.h"
#include "sdhci-xenon.h"
static int xenon_enable_internal_clk(struct sdhci_host *host)
{
u32 reg;
ktime_t timeout;
reg = sdhci_readl(host, SDHCI_CLOCK_CONTROL);
reg |= SDHCI_CLOCK_INT_EN;
sdhci_writel(host, reg, SDHCI_CLOCK_CONTROL);
/* Wait max 20 ms */
timeout = ktime_add_ms(ktime_get(), 20);
while (1) {
bool timedout = ktime_after(ktime_get(), timeout);
reg = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
if (reg & SDHCI_CLOCK_INT_STABLE)
break;
if (timedout) {
dev_err(mmc_dev(host->mmc), "Internal clock never stabilised.\n");
return -ETIMEDOUT;
}
usleep_range(900, 1100);
}
return 0;
}
/* Set SDCLK-off-while-idle */
static void xenon_set_sdclk_off_idle(struct sdhci_host *host,
unsigned char sdhc_id, bool enable)
{
u32 reg;
u32 mask;
reg = sdhci_readl(host, XENON_SYS_OP_CTRL);
/* Get the bit shift basing on the SDHC index */
mask = (0x1 << (XENON_SDCLK_IDLEOFF_ENABLE_SHIFT + sdhc_id));
if (enable)
reg |= mask;
else
reg &= ~mask;
sdhci_writel(host, reg, XENON_SYS_OP_CTRL);
}
/* Enable/Disable the Auto Clock Gating function */
static void xenon_set_acg(struct sdhci_host *host, bool enable)
{
u32 reg;
reg = sdhci_readl(host, XENON_SYS_OP_CTRL);
if (enable)
reg &= ~XENON_AUTO_CLKGATE_DISABLE_MASK;
else
reg |= XENON_AUTO_CLKGATE_DISABLE_MASK;
sdhci_writel(host, reg, XENON_SYS_OP_CTRL);
}
/* Enable this SDHC */
static void xenon_enable_sdhc(struct sdhci_host *host,
unsigned char sdhc_id)
{
u32 reg;
reg = sdhci_readl(host, XENON_SYS_OP_CTRL);
reg |= (BIT(sdhc_id) << XENON_SLOT_ENABLE_SHIFT);
sdhci_writel(host, reg, XENON_SYS_OP_CTRL);
host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY;
/*
* Force to clear BUS_TEST to
* skip bus_test_pre and bus_test_post
*/
host->mmc->caps &= ~MMC_CAP_BUS_WIDTH_TEST;
}
/* Disable this SDHC */
static void xenon_disable_sdhc(struct sdhci_host *host,
unsigned char sdhc_id)
{
u32 reg;
reg = sdhci_readl(host, XENON_SYS_OP_CTRL);
reg &= ~(BIT(sdhc_id) << XENON_SLOT_ENABLE_SHIFT);
sdhci_writel(host, reg, XENON_SYS_OP_CTRL);
}
/* Enable Parallel Transfer Mode */
static void xenon_enable_sdhc_parallel_tran(struct sdhci_host *host,
unsigned char sdhc_id)
{
u32 reg;
reg = sdhci_readl(host, XENON_SYS_EXT_OP_CTRL);
reg |= BIT(sdhc_id);
sdhci_writel(host, reg, XENON_SYS_EXT_OP_CTRL);
}
/* Mask command conflict error */
static void xenon_mask_cmd_conflict_err(struct sdhci_host *host)
{
u32 reg;
reg = sdhci_readl(host, XENON_SYS_EXT_OP_CTRL);
reg |= XENON_MASK_CMD_CONFLICT_ERR;
sdhci_writel(host, reg, XENON_SYS_EXT_OP_CTRL);
}
static void xenon_retune_setup(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
u32 reg;
/* Disable the Re-Tuning Request functionality */
reg = sdhci_readl(host, XENON_SLOT_RETUNING_REQ_CTRL);
reg &= ~XENON_RETUNING_COMPATIBLE;
sdhci_writel(host, reg, XENON_SLOT_RETUNING_REQ_CTRL);
/* Disable the Re-tuning Interrupt */
reg = sdhci_readl(host, SDHCI_SIGNAL_ENABLE);
reg &= ~SDHCI_INT_RETUNE;
sdhci_writel(host, reg, SDHCI_SIGNAL_ENABLE);
reg = sdhci_readl(host, SDHCI_INT_ENABLE);
reg &= ~SDHCI_INT_RETUNE;
sdhci_writel(host, reg, SDHCI_INT_ENABLE);
/* Force to use Tuning Mode 1 */
host->tuning_mode = SDHCI_TUNING_MODE_1;
/* Set re-tuning period */
host->tuning_count = 1 << (priv->tuning_count - 1);
}
/*
* Operations inside struct sdhci_ops
*/
/* Recover the Register Setting cleared during SOFTWARE_RESET_ALL */
static void xenon_reset_exit(struct sdhci_host *host,
unsigned char sdhc_id, u8 mask)
{
/* Only SOFTWARE RESET ALL will clear the register setting */
if (!(mask & SDHCI_RESET_ALL))
return;
/* Disable tuning request and auto-retuning again */
xenon_retune_setup(host);
/*
* The ACG should be turned off at the early init time, in order
* to solve a possible issues with the 1.8V regulator stabilization.
* The feature is enabled in later stage.
*/
xenon_set_acg(host, false);
xenon_set_sdclk_off_idle(host, sdhc_id, false);
xenon_mask_cmd_conflict_err(host);
}
static void xenon_reset(struct sdhci_host *host, u8 mask)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
sdhci_reset(host, mask);
xenon_reset_exit(host, priv->sdhc_id, mask);
}
/*
* Xenon defines different values for HS200 and HS400
* in Host_Control_2
*/
static void xenon_set_uhs_signaling(struct sdhci_host *host,
unsigned int timing)
{
u16 ctrl_2;
ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
/* Select Bus Speed Mode for host */
ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
if (timing == MMC_TIMING_MMC_HS200)
ctrl_2 |= XENON_CTRL_HS200;
else if (timing == MMC_TIMING_UHS_SDR104)
ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
else if (timing == MMC_TIMING_UHS_SDR12)
ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
else if (timing == MMC_TIMING_UHS_SDR25)
ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
else if (timing == MMC_TIMING_UHS_SDR50)
ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
else if ((timing == MMC_TIMING_UHS_DDR50) ||
(timing == MMC_TIMING_MMC_DDR52))
ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
else if (timing == MMC_TIMING_MMC_HS400)
ctrl_2 |= XENON_CTRL_HS400;
sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
}
static void xenon_set_power(struct sdhci_host *host, unsigned char mode,
unsigned short vdd)
{
struct mmc_host *mmc = host->mmc;
u8 pwr = host->pwr;
sdhci_set_power_noreg(host, mode, vdd);
if (host->pwr == pwr)
return;
if (host->pwr == 0)
vdd = 0;
if (!IS_ERR(mmc->supply.vmmc))
mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
}
static void xenon_voltage_switch(struct sdhci_host *host)
{
/* Wait for 5ms after set 1.8V signal enable bit */
usleep_range(5000, 5500);
}
static unsigned int xenon_get_max_clock(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
if (pltfm_host->clk)
return sdhci_pltfm_clk_get_max_clock(host);
else
return pltfm_host->clock;
}
static const struct sdhci_ops sdhci_xenon_ops = {
.voltage_switch = xenon_voltage_switch,
.set_clock = sdhci_set_clock,
.set_power = xenon_set_power,
.set_bus_width = sdhci_set_bus_width,
.reset = xenon_reset,
.set_uhs_signaling = xenon_set_uhs_signaling,
.get_max_clock = xenon_get_max_clock,
};
static const struct sdhci_pltfm_data sdhci_xenon_pdata = {
.ops = &sdhci_xenon_ops,
.quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER |
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
};
/*
* Xenon Specific Operations in mmc_host_ops
*/
static void xenon_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
{
struct sdhci_host *host = mmc_priv(mmc);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
u32 reg;
/*
* HS400/HS200/eMMC HS doesn't have Preset Value register.
* However, sdhci_set_ios will read HS400/HS200 Preset register.
* Disable Preset Value register for HS400/HS200.
* eMMC HS with preset_enabled set will trigger a bug in
* get_preset_value().
*/
if ((ios->timing == MMC_TIMING_MMC_HS400) ||
(ios->timing == MMC_TIMING_MMC_HS200) ||
(ios->timing == MMC_TIMING_MMC_HS)) {
host->preset_enabled = false;
host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
host->flags &= ~SDHCI_PV_ENABLED;
reg = sdhci_readw(host, SDHCI_HOST_CONTROL2);
reg &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
sdhci_writew(host, reg, SDHCI_HOST_CONTROL2);
} else {
host->quirks2 &= ~SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
}
sdhci_set_ios(mmc, ios);
xenon_phy_adj(host, ios);
if (host->clock > XENON_DEFAULT_SDCLK_FREQ)
xenon_set_sdclk_off_idle(host, priv->sdhc_id, true);
}
static int xenon_start_signal_voltage_switch(struct mmc_host *mmc,
struct mmc_ios *ios)
{
struct sdhci_host *host = mmc_priv(mmc);
/*
* Before SD/SDIO set signal voltage, SD bus clock should be
* disabled. However, sdhci_set_clock will also disable the Internal
* clock in mmc_set_signal_voltage().
* If Internal clock is disabled, the 3.3V/1.8V bit can not be updated.
* Thus here manually enable internal clock.
*
* After switch completes, it is unnecessary to disable internal clock,
* since keeping internal clock active obeys SD spec.
*/
xenon_enable_internal_clk(host);
xenon_soc_pad_ctrl(host, ios->signal_voltage);
/*
* If Vqmmc is fixed on platform, vqmmc regulator should be unavailable.
* Thus SDHCI_CTRL_VDD_180 bit might not work then.
* Skip the standard voltage switch to avoid any issue.
*/
if (PTR_ERR(mmc->supply.vqmmc) == -ENODEV)
return 0;
return sdhci_start_signal_voltage_switch(mmc, ios);
}
/*
* Update card type.
* priv->init_card_type will be used in PHY timing adjustment.
*/
static void xenon_init_card(struct mmc_host *mmc, struct mmc_card *card)
{
struct sdhci_host *host = mmc_priv(mmc);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
/* Update card type*/
priv->init_card_type = card->type;
}
static int xenon_execute_tuning(struct mmc_host *mmc, u32 opcode)
{
struct sdhci_host *host = mmc_priv(mmc);
if (host->timing == MMC_TIMING_UHS_DDR50 ||
host->timing == MMC_TIMING_MMC_DDR52)
return 0;
/*
* Currently force Xenon driver back to support mode 1 only,
* even though Xenon might claim to support mode 2 or mode 3.
* It requires more time to test mode 2/mode 3 on more platforms.
*/
if (host->tuning_mode != SDHCI_TUNING_MODE_1)
xenon_retune_setup(host);
return sdhci_execute_tuning(mmc, opcode);
}
static void xenon_enable_sdio_irq(struct mmc_host *mmc, int enable)
{
struct sdhci_host *host = mmc_priv(mmc);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
u32 reg;
u8 sdhc_id = priv->sdhc_id;
sdhci_enable_sdio_irq(mmc, enable);
if (enable) {
/*
* Set SDIO Card Inserted indication
* to enable detecting SDIO async irq.
*/
reg = sdhci_readl(host, XENON_SYS_CFG_INFO);
reg |= (1 << (sdhc_id + XENON_SLOT_TYPE_SDIO_SHIFT));
sdhci_writel(host, reg, XENON_SYS_CFG_INFO);
} else {
/* Clear SDIO Card Inserted indication */
reg = sdhci_readl(host, XENON_SYS_CFG_INFO);
reg &= ~(1 << (sdhc_id + XENON_SLOT_TYPE_SDIO_SHIFT));
sdhci_writel(host, reg, XENON_SYS_CFG_INFO);
}
}
static void xenon_replace_mmc_host_ops(struct sdhci_host *host)
{
host->mmc_host_ops.set_ios = xenon_set_ios;
host->mmc_host_ops.start_signal_voltage_switch =
xenon_start_signal_voltage_switch;
host->mmc_host_ops.init_card = xenon_init_card;
host->mmc_host_ops.execute_tuning = xenon_execute_tuning;
host->mmc_host_ops.enable_sdio_irq = xenon_enable_sdio_irq;
}
/*
* Parse Xenon specific DT properties:
* sdhc-id: the index of current SDHC.
* Refer to XENON_SYS_CFG_INFO register
* tun-count: the interval between re-tuning
*/
static int xenon_probe_params(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct sdhci_host *host = platform_get_drvdata(pdev);
struct mmc_host *mmc = host->mmc;
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
u32 sdhc_id, nr_sdhc;
u32 tuning_count;
struct sysinfo si;
/* Disable HS200 on Armada AP806 */
if (priv->hw_version == XENON_AP806)
host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200;
sdhc_id = 0x0;
if (!device_property_read_u32(dev, "marvell,xenon-sdhc-id", &sdhc_id)) {
nr_sdhc = sdhci_readl(host, XENON_SYS_CFG_INFO);
nr_sdhc &= XENON_NR_SUPPORTED_SLOT_MASK;
if (unlikely(sdhc_id > nr_sdhc)) {
dev_err(mmc_dev(mmc), "SDHC Index %d exceeds Number of SDHCs %d\n",
sdhc_id, nr_sdhc);
return -EINVAL;
}
}
priv->sdhc_id = sdhc_id;
tuning_count = XENON_DEF_TUNING_COUNT;
if (!device_property_read_u32(dev, "marvell,xenon-tun-count",
&tuning_count)) {
if (unlikely(tuning_count >= XENON_TMR_RETUN_NO_PRESENT)) {
dev_err(mmc_dev(mmc), "Wrong Re-tuning Count. Set default value %d\n",
XENON_DEF_TUNING_COUNT);
tuning_count = XENON_DEF_TUNING_COUNT;
}
}
priv->tuning_count = tuning_count;
/*
* AC5/X/IM HW has only 31-bits passed in the crossbar switch.
* If we have more than 2GB of memory, this means we might pass
* memory pointers which are above 2GB and which cannot be properly
* represented. In this case, disable ADMA, 64-bit DMA and allow only SDMA.
* This effectively will enable bounce buffer quirk in the
* generic SDHCI driver, which will make sure DMA is only done
* from supported memory regions:
*/
if (priv->hw_version == XENON_AC5) {
si_meminfo(&si);
if (si.totalram * si.mem_unit > SZ_2G) {
host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
host->quirks2 |= SDHCI_QUIRK2_BROKEN_64_BIT_DMA;
}
}
return xenon_phy_parse_params(dev, host);
}
static int xenon_sdhc_prepare(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
u8 sdhc_id = priv->sdhc_id;
/* Enable SDHC */
xenon_enable_sdhc(host, sdhc_id);
/* Enable ACG */
xenon_set_acg(host, true);
/* Enable Parallel Transfer Mode */
xenon_enable_sdhc_parallel_tran(host, sdhc_id);
/* Disable SDCLK-Off-While-Idle before card init */
xenon_set_sdclk_off_idle(host, sdhc_id, false);
xenon_mask_cmd_conflict_err(host);
return 0;
}
static void xenon_sdhc_unprepare(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
u8 sdhc_id = priv->sdhc_id;
/* disable SDHC */
xenon_disable_sdhc(host, sdhc_id);
}
static int xenon_probe(struct platform_device *pdev)
{
struct sdhci_pltfm_host *pltfm_host;
struct device *dev = &pdev->dev;
struct sdhci_host *host;
struct xenon_priv *priv;
int err;
host = sdhci_pltfm_init(pdev, &sdhci_xenon_pdata,
sizeof(struct xenon_priv));
if (IS_ERR(host))
return PTR_ERR(host);
pltfm_host = sdhci_priv(host);
priv = sdhci_pltfm_priv(pltfm_host);
priv->hw_version = (unsigned long)device_get_match_data(&pdev->dev);
/*
* Link Xenon specific mmc_host_ops function,
* to replace standard ones in sdhci_ops.
*/
xenon_replace_mmc_host_ops(host);
if (dev->of_node) {
pltfm_host->clk = devm_clk_get(&pdev->dev, "core");
if (IS_ERR(pltfm_host->clk)) {
err = PTR_ERR(pltfm_host->clk);
dev_err(&pdev->dev, "Failed to setup input clk: %d\n", err);
goto free_pltfm;
}
err = clk_prepare_enable(pltfm_host->clk);
if (err)
goto free_pltfm;
priv->axi_clk = devm_clk_get(&pdev->dev, "axi");
if (IS_ERR(priv->axi_clk)) {
err = PTR_ERR(priv->axi_clk);
if (err == -EPROBE_DEFER)
goto err_clk;
} else {
err = clk_prepare_enable(priv->axi_clk);
if (err)
goto err_clk;
}
}
err = mmc_of_parse(host->mmc);
if (err)
goto err_clk_axi;
sdhci_get_property(pdev);
xenon_set_acg(host, false);
/* Xenon specific parameters parse */
err = xenon_probe_params(pdev);
if (err)
goto err_clk_axi;
err = xenon_sdhc_prepare(host);
if (err)
goto err_clk_axi;
pm_runtime_get_noresume(&pdev->dev);
pm_runtime_set_active(&pdev->dev);
pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
pm_runtime_use_autosuspend(&pdev->dev);
pm_runtime_enable(&pdev->dev);
pm_suspend_ignore_children(&pdev->dev, 1);
err = sdhci_add_host(host);
if (err)
goto remove_sdhc;
pm_runtime_put_autosuspend(&pdev->dev);
/*
* If we previously detected AC5 with over 2GB of memory,
* then we disable ADMA and 64-bit DMA.
* This means generic SDHCI driver has set the DMA mask to
* 32-bit. Since DDR starts at 0x2_0000_0000, we must use
* 34-bit DMA mask to access this DDR memory:
*/
if (priv->hw_version == XENON_AC5 &&
host->quirks2 & SDHCI_QUIRK2_BROKEN_64_BIT_DMA)
dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(34));
return 0;
remove_sdhc:
pm_runtime_disable(&pdev->dev);
pm_runtime_put_noidle(&pdev->dev);
xenon_sdhc_unprepare(host);
err_clk_axi:
clk_disable_unprepare(priv->axi_clk);
err_clk:
clk_disable_unprepare(pltfm_host->clk);
free_pltfm:
sdhci_pltfm_free(pdev);
return err;
}
static void xenon_remove(struct platform_device *pdev)
{
struct sdhci_host *host = platform_get_drvdata(pdev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
pm_runtime_get_sync(&pdev->dev);
pm_runtime_disable(&pdev->dev);
pm_runtime_put_noidle(&pdev->dev);
sdhci_remove_host(host, 0);
xenon_sdhc_unprepare(host);
clk_disable_unprepare(priv->axi_clk);
clk_disable_unprepare(pltfm_host->clk);
sdhci_pltfm_free(pdev);
}
#ifdef CONFIG_PM_SLEEP
static int xenon_suspend(struct device *dev)
{
struct sdhci_host *host = dev_get_drvdata(dev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
int ret;
ret = pm_runtime_force_suspend(dev);
priv->restore_needed = true;
return ret;
}
#endif
#ifdef CONFIG_PM
static int xenon_runtime_suspend(struct device *dev)
{
struct sdhci_host *host = dev_get_drvdata(dev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
int ret;
ret = sdhci_runtime_suspend_host(host);
if (ret)
return ret;
if (host->tuning_mode != SDHCI_TUNING_MODE_3)
mmc_retune_needed(host->mmc);
clk_disable_unprepare(pltfm_host->clk);
/*
* Need to update the priv->clock here, or when runtime resume
* back, phy don't aware the clock change and won't adjust phy
* which will cause cmd err
*/
priv->clock = 0;
return 0;
}
static int xenon_runtime_resume(struct device *dev)
{
struct sdhci_host *host = dev_get_drvdata(dev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
int ret;
ret = clk_prepare_enable(pltfm_host->clk);
if (ret) {
dev_err(dev, "can't enable mainck\n");
return ret;
}
if (priv->restore_needed) {
ret = xenon_sdhc_prepare(host);
if (ret)
goto out;
priv->restore_needed = false;
}
ret = sdhci_runtime_resume_host(host, 0);
if (ret)
goto out;
return 0;
out:
clk_disable_unprepare(pltfm_host->clk);
return ret;
}
#endif /* CONFIG_PM */
static const struct dev_pm_ops sdhci_xenon_dev_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(xenon_suspend,
pm_runtime_force_resume)
SET_RUNTIME_PM_OPS(xenon_runtime_suspend,
xenon_runtime_resume,
NULL)
};
static const struct of_device_id sdhci_xenon_dt_ids[] = {
{ .compatible = "marvell,armada-ap806-sdhci", .data = (void *)XENON_AP806},
{ .compatible = "marvell,armada-ap807-sdhci", .data = (void *)XENON_AP807},
{ .compatible = "marvell,armada-cp110-sdhci", .data = (void *)XENON_CP110},
{ .compatible = "marvell,armada-3700-sdhci", .data = (void *)XENON_A3700},
{ .compatible = "marvell,ac5-sdhci", .data = (void *)XENON_AC5},
{}
};
MODULE_DEVICE_TABLE(of, sdhci_xenon_dt_ids);
#ifdef CONFIG_ACPI
static const struct acpi_device_id sdhci_xenon_acpi_ids[] = {
{ .id = "MRVL0002", XENON_AP806},
{ .id = "MRVL0003", XENON_AP807},
{ .id = "MRVL0004", XENON_CP110},
{}
};
MODULE_DEVICE_TABLE(acpi, sdhci_xenon_acpi_ids);
#endif
static struct platform_driver sdhci_xenon_driver = {
.driver = {
.name = "xenon-sdhci",
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
.of_match_table = sdhci_xenon_dt_ids,
.acpi_match_table = ACPI_PTR(sdhci_xenon_acpi_ids),
.pm = &sdhci_xenon_dev_pm_ops,
},
.probe = xenon_probe,
.remove_new = xenon_remove,
};
module_platform_driver(sdhci_xenon_driver);
MODULE_DESCRIPTION("SDHCI platform driver for Marvell Xenon SDHC");
MODULE_AUTHOR("Hu Ziji <huziji@marvell.com>");
MODULE_LICENSE("GPL v2");