mirror of
https://github.com/torvalds/linux.git
synced 2024-11-19 10:31:48 +00:00
e8b1cc3a34
Add basic DMA configuration for u5500 supporting memcpy. Make way for SDI0 dma support by setting SDI0 to -1, indicating it will be configured in runtime. Signed-off-by: Per Forlin <per.forlin@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
121 lines
3.2 KiB
C
121 lines
3.2 KiB
C
/*
|
|
* Copyright (C) ST-Ericsson SA 2010
|
|
*
|
|
* Author: Per Forlin <per.forlin@stericsson.com> for ST-Ericsson
|
|
* Author: Jonas Aaberg <jonas.aberg@stericsson.com> for ST-Ericsson
|
|
* Author: Rabin Vincent <rabinv.vincent@stericsson.com> for ST-Ericsson
|
|
*
|
|
* License terms: GNU General Public License (GPL), version 2
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/platform_device.h>
|
|
|
|
#include <plat/ste_dma40.h>
|
|
#include <mach/setup.h>
|
|
#include <mach/hardware.h>
|
|
|
|
#include "ste-dma40-db5500.h"
|
|
|
|
static struct resource dma40_resources[] = {
|
|
[0] = {
|
|
.start = U5500_DMA_BASE,
|
|
.end = U5500_DMA_BASE + SZ_4K - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
.name = "base",
|
|
},
|
|
[1] = {
|
|
.start = U5500_DMA_LCPA_BASE,
|
|
.end = U5500_DMA_LCPA_BASE + 2 * SZ_1K - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
.name = "lcpa",
|
|
},
|
|
[2] = {
|
|
.start = IRQ_DB5500_DMA,
|
|
.end = IRQ_DB5500_DMA,
|
|
.flags = IORESOURCE_IRQ
|
|
}
|
|
};
|
|
|
|
/* Default configuration for physical memcpy */
|
|
static struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
|
|
.mode = STEDMA40_MODE_PHYSICAL,
|
|
.dir = STEDMA40_MEM_TO_MEM,
|
|
|
|
.src_info.data_width = STEDMA40_BYTE_WIDTH,
|
|
.src_info.psize = STEDMA40_PSIZE_PHY_1,
|
|
.src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
|
|
|
|
.dst_info.data_width = STEDMA40_BYTE_WIDTH,
|
|
.dst_info.psize = STEDMA40_PSIZE_PHY_1,
|
|
.dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
|
|
};
|
|
|
|
/* Default configuration for logical memcpy */
|
|
static struct stedma40_chan_cfg dma40_memcpy_conf_log = {
|
|
.dir = STEDMA40_MEM_TO_MEM,
|
|
|
|
.src_info.data_width = STEDMA40_BYTE_WIDTH,
|
|
.src_info.psize = STEDMA40_PSIZE_LOG_1,
|
|
.src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
|
|
|
|
.dst_info.data_width = STEDMA40_BYTE_WIDTH,
|
|
.dst_info.psize = STEDMA40_PSIZE_LOG_1,
|
|
.dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
|
|
};
|
|
|
|
/*
|
|
* Mapping between soruce event lines and physical device address This was
|
|
* created assuming that the event line is tied to a device and therefore the
|
|
* address is constant, however this is not true for at least USB, and the
|
|
* values are just placeholders for USB. This table is preserved and used for
|
|
* now.
|
|
*/
|
|
static const dma_addr_t dma40_rx_map[DB5500_DMA_NR_DEV] = {
|
|
[DB5500_DMA_DEV24_SDMMC0_RX] = -1,
|
|
};
|
|
|
|
/* Mapping between destination event lines and physical device address */
|
|
static const dma_addr_t dma40_tx_map[DB5500_DMA_NR_DEV] = {
|
|
[DB5500_DMA_DEV24_SDMMC0_TX] = -1,
|
|
};
|
|
|
|
static int dma40_memcpy_event[] = {
|
|
DB5500_DMA_MEMCPY_TX_1,
|
|
DB5500_DMA_MEMCPY_TX_2,
|
|
DB5500_DMA_MEMCPY_TX_3,
|
|
DB5500_DMA_MEMCPY_TX_4,
|
|
DB5500_DMA_MEMCPY_TX_5,
|
|
};
|
|
|
|
static struct stedma40_platform_data dma40_plat_data = {
|
|
.dev_len = ARRAY_SIZE(dma40_rx_map),
|
|
.dev_rx = dma40_rx_map,
|
|
.dev_tx = dma40_tx_map,
|
|
.memcpy = dma40_memcpy_event,
|
|
.memcpy_len = ARRAY_SIZE(dma40_memcpy_event),
|
|
.memcpy_conf_phy = &dma40_memcpy_conf_phy,
|
|
.memcpy_conf_log = &dma40_memcpy_conf_log,
|
|
.disabled_channels = {-1},
|
|
};
|
|
|
|
static struct platform_device dma40_device = {
|
|
.dev = {
|
|
.platform_data = &dma40_plat_data,
|
|
},
|
|
.name = "dma40",
|
|
.id = 0,
|
|
.num_resources = ARRAY_SIZE(dma40_resources),
|
|
.resource = dma40_resources
|
|
};
|
|
|
|
void __init db5500_dma_init(void)
|
|
{
|
|
int ret;
|
|
|
|
ret = platform_device_register(&dma40_device);
|
|
if (ret)
|
|
dev_err(&dma40_device.dev, "unable to register device: %d\n", ret);
|
|
|
|
}
|