mirror of
https://github.com/torvalds/linux.git
synced 2024-11-19 18:41:48 +00:00
e260d2bbc9
Add pinctrl driver support for IPQ4019 platform Signed-off-by: Sricharan R <sricharan@codeaurora.org> Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org> Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org> Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Andy Gross <andy.gross@linaro.org> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> [Dropped .owner assignment] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
75 lines
2.6 KiB
Plaintext
75 lines
2.6 KiB
Plaintext
Qualcomm Atheros IPQ4019 TLMM block
|
|
|
|
This is the Top Level Mode Multiplexor block found on the Qualcomm IPQ8019
|
|
platform, it provides pinctrl, pinmux, pinconf, and gpiolib facilities.
|
|
|
|
Required properties:
|
|
- compatible: "qcom,ipq4019-pinctrl"
|
|
- reg: Should be the base address and length of the TLMM block.
|
|
- interrupts: Should be the parent IRQ of the TLMM block.
|
|
- interrupt-controller: Marks the device node as an interrupt controller.
|
|
- #interrupt-cells: Should be two.
|
|
- gpio-controller: Marks the device node as a GPIO controller.
|
|
- #gpio-cells : Should be two.
|
|
The first cell is the gpio pin number and the
|
|
second cell is used for optional parameters.
|
|
|
|
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
|
|
a general description of GPIO and interrupt bindings.
|
|
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
|
common pinctrl bindings used by client devices, including the meaning of the
|
|
phrase "pin configuration node".
|
|
|
|
The pin configuration nodes act as a container for an abitrary number of
|
|
subnodes. Each of these subnodes represents some desired configuration for a
|
|
pin, a group, or a list of pins or groups. This configuration can include the
|
|
mux function to select on those pin(s)/group(s), and various pin configuration
|
|
parameters, such as pull-up, drive strength, etc.
|
|
|
|
The name of each subnode is not important; all subnodes should be enumerated
|
|
and processed purely based on their content.
|
|
|
|
Each subnode only affects those parameters that are explicitly listed. In
|
|
other words, a subnode that lists a mux function but no pin configuration
|
|
parameters implies no information about any pin configuration parameters.
|
|
Similarly, a pin subnode that describes a pullup parameter implies no
|
|
information about e.g. the mux function.
|
|
|
|
|
|
The following generic properties as defined in pinctrl-bindings.txt are valid
|
|
to specify in a pin configuration subnode:
|
|
pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength.
|
|
|
|
Non-empty subnodes must specify the 'pins' property.
|
|
Note that not all properties are valid for all pins.
|
|
|
|
|
|
Valid values for qcom,pins are:
|
|
gpio0-gpio99
|
|
Supports mux, bias and drive-strength
|
|
|
|
Valid values for qcom,function are:
|
|
gpio, blsp_uart1, blsp_i2c0, blsp_i2c1, blsp_uart0, blsp_spi1, blsp_spi0
|
|
|
|
Example:
|
|
|
|
tlmm: pinctrl@1000000 {
|
|
compatible = "qcom,ipq4019-pinctrl";
|
|
reg = <0x1000000 0x300000>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupts = <0 208 0>;
|
|
|
|
serial_pins: serial_pinmux {
|
|
mux {
|
|
pins = "gpio60", "gpio61";
|
|
function = "blsp_uart0";
|
|
bias-disable;
|
|
};
|
|
};
|
|
};
|