linux/drivers/net/mdio/Makefile
Maxime Chevallier 642af0f92c net: mdio: Introduce a regmap-based mdio driver
There exists several examples today of devices that embed an ethernet
PHY or PCS directly inside an SoC. In this situation, either the device
is controlled through a vendor-specific register set, or sometimes
exposes the standard 802.3 registers that are typically accessed over
MDIO.

As phylib and phylink are designed to use mdiodevices, this driver
allows creating a virtual MDIO bus, that translates mdiodev register
accesses to regmap accesses.

The reason we use regmap is because there are at least 3 such devices
known today, 2 of them are Altera TSE PCS's, memory-mapped, exposed
with a 4-byte stride in stmmac's dwmac-socfpga variant, and a 2-byte
stride in altera-tse. The other one (nxp,sja1110-base-tx-mdio) is
exposed over SPI.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-05 09:56:36 +01:00

35 lines
1.4 KiB
Makefile

# SPDX-License-Identifier: GPL-2.0
# Makefile for Linux MDIO bus drivers
obj-$(CONFIG_ACPI_MDIO) += acpi_mdio.o
obj-$(CONFIG_FWNODE_MDIO) += fwnode_mdio.o
obj-$(CONFIG_OF_MDIO) += of_mdio.o
obj-$(CONFIG_MDIO_ASPEED) += mdio-aspeed.o
obj-$(CONFIG_MDIO_BCM_IPROC) += mdio-bcm-iproc.o
obj-$(CONFIG_MDIO_BCM_UNIMAC) += mdio-bcm-unimac.o
obj-$(CONFIG_MDIO_BITBANG) += mdio-bitbang.o
obj-$(CONFIG_MDIO_CAVIUM) += mdio-cavium.o
obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o
obj-$(CONFIG_MDIO_HISI_FEMAC) += mdio-hisi-femac.o
obj-$(CONFIG_MDIO_I2C) += mdio-i2c.o
obj-$(CONFIG_MDIO_IPQ4019) += mdio-ipq4019.o
obj-$(CONFIG_MDIO_IPQ8064) += mdio-ipq8064.o
obj-$(CONFIG_MDIO_MOXART) += mdio-moxart.o
obj-$(CONFIG_MDIO_MSCC_MIIM) += mdio-mscc-miim.o
obj-$(CONFIG_MDIO_MVUSB) += mdio-mvusb.o
obj-$(CONFIG_MDIO_OCTEON) += mdio-octeon.o
obj-$(CONFIG_MDIO_REGMAP) += mdio-regmap.o
obj-$(CONFIG_MDIO_SUN4I) += mdio-sun4i.o
obj-$(CONFIG_MDIO_THUNDER) += mdio-thunder.o
obj-$(CONFIG_MDIO_XGENE) += mdio-xgene.o
obj-$(CONFIG_MDIO_BUS_MUX) += mdio-mux.o
obj-$(CONFIG_MDIO_BUS_MUX_BCM6368) += mdio-mux-bcm6368.o
obj-$(CONFIG_MDIO_BUS_MUX_BCM_IPROC) += mdio-mux-bcm-iproc.o
obj-$(CONFIG_MDIO_BUS_MUX_GPIO) += mdio-mux-gpio.o
obj-$(CONFIG_MDIO_BUS_MUX_MESON_G12A) += mdio-mux-meson-g12a.o
obj-$(CONFIG_MDIO_BUS_MUX_MESON_GXL) += mdio-mux-meson-gxl.o
obj-$(CONFIG_MDIO_BUS_MUX_MMIOREG) += mdio-mux-mmioreg.o
obj-$(CONFIG_MDIO_BUS_MUX_MULTIPLEXER) += mdio-mux-multiplexer.o