mirror of
https://github.com/torvalds/linux.git
synced 2024-12-27 05:11:48 +00:00
87 lines
3.5 KiB
C
87 lines
3.5 KiB
C
#ifndef HOSTAP_CONFIG_H
|
|
#define HOSTAP_CONFIG_H
|
|
|
|
#define PRISM2_VERSION "CVS"
|
|
|
|
/* In the previous versions of Host AP driver, support for user space version
|
|
* of IEEE 802.11 management (hostapd) used to be disabled in the default
|
|
* configuration. From now on, support for hostapd is always included and it is
|
|
* possible to disable kernel driver version of IEEE 802.11 management with a
|
|
* separate define, PRISM2_NO_KERNEL_IEEE80211_MGMT. */
|
|
/* #define PRISM2_NO_KERNEL_IEEE80211_MGMT */
|
|
|
|
/* Maximum number of events handler per one interrupt */
|
|
#define PRISM2_MAX_INTERRUPT_EVENTS 20
|
|
|
|
/* Use PCI bus master to copy data to/from BAP (only available for
|
|
* hostap_pci.o).
|
|
*
|
|
* Note! This is extremely experimental. PCI bus master is not supported by
|
|
* Intersil and it seems to have some problems at least on TX path (see below).
|
|
* The driver code for implementing bus master support is based on guessing
|
|
* and experimenting suitable control bits and these might not be correct.
|
|
* This code is included because using bus master makes a huge difference in
|
|
* host CPU load (something like 40% host CPU usage to 5-10% when sending or
|
|
* receiving at maximum throughput).
|
|
*
|
|
* Note2! Station firmware version 1.3.5 and primary firmware version 1.0.7
|
|
* have some fixes for PCI corruption and these (or newer) versions are
|
|
* recommended especially when using bus mastering.
|
|
*
|
|
* NOTE: PCI bus mastering code has not been updated for long time and it is
|
|
* not likely to compile and it will _not_ work as is. Only enable this if you
|
|
* are prepared to first fix the implementation..
|
|
*/
|
|
/* #define PRISM2_BUS_MASTER */
|
|
|
|
#ifdef PRISM2_BUS_MASTER
|
|
|
|
/* PCI bus master implementation seems to be broken in current
|
|
* hardware/firmware versions. Enable this to use enable command to fix
|
|
* something before starting bus master operation on TX path. This will add
|
|
* some latency and an extra interrupt to each TX packet. */
|
|
#define PRISM2_ENABLE_BEFORE_TX_BUS_MASTER
|
|
|
|
#endif /* PRISM2_BUS_MASTER */
|
|
|
|
/* Include code for downloading firmware images into volatile RAM. */
|
|
#define PRISM2_DOWNLOAD_SUPPORT
|
|
|
|
/* Allow kernel configuration to enable download support. */
|
|
#if !defined(PRISM2_DOWNLOAD_SUPPORT) && defined(CONFIG_HOSTAP_FIRMWARE)
|
|
#define PRISM2_DOWNLOAD_SUPPORT
|
|
#endif
|
|
|
|
#ifdef PRISM2_DOWNLOAD_SUPPORT
|
|
/* Allow writing firmware images into flash, i.e., to non-volatile storage.
|
|
* Before you enable this option, you should make absolutely sure that you are
|
|
* using prism2_srec utility that comes with THIS version of the driver!
|
|
* In addition, please note that it is possible to kill your card with
|
|
* non-volatile download if you are using incorrect image. This feature has not
|
|
* been fully tested, so please be careful with it. */
|
|
/* #define PRISM2_NON_VOLATILE_DOWNLOAD */
|
|
#endif /* PRISM2_DOWNLOAD_SUPPORT */
|
|
|
|
/* Save low-level I/O for debugging. This should not be enabled in normal use.
|
|
*/
|
|
/* #define PRISM2_IO_DEBUG */
|
|
|
|
/* Following defines can be used to remove unneeded parts of the driver, e.g.,
|
|
* to limit the size of the kernel module. Definitions can be added here in
|
|
* hostap_config.h or they can be added to make command with EXTRA_CFLAGS,
|
|
* e.g.,
|
|
* 'make pccard EXTRA_CFLAGS="-DPRISM2_NO_DEBUG -DPRISM2_NO_PROCFS_DEBUG"'
|
|
*/
|
|
|
|
/* Do not include debug messages into the driver */
|
|
/* #define PRISM2_NO_DEBUG */
|
|
|
|
/* Do not include /proc/net/prism2/wlan#/{registers,debug} */
|
|
/* #define PRISM2_NO_PROCFS_DEBUG */
|
|
|
|
/* Do not include station functionality (i.e., allow only Master (Host AP) mode
|
|
*/
|
|
/* #define PRISM2_NO_STATION_MODES */
|
|
|
|
#endif /* HOSTAP_CONFIG_H */
|