mirror of
https://github.com/torvalds/linux.git
synced 2024-11-17 17:41:44 +00:00
d9bdffd210
Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
121 lines
2.9 KiB
C
121 lines
2.9 KiB
C
/*
|
|
* Support for the S1 button on Routerboard 532
|
|
*
|
|
* Copyright (C) 2009 Phil Sutter <n0-1@freewrt.org>
|
|
*/
|
|
|
|
#include <linux/input-polldev.h>
|
|
#include <linux/module.h>
|
|
#include <linux/platform_device.h>
|
|
|
|
#include <asm/mach-rc32434/gpio.h>
|
|
#include <asm/mach-rc32434/rb.h>
|
|
|
|
#define DRV_NAME "rb532-button"
|
|
|
|
#define RB532_BTN_RATE 100 /* msec */
|
|
#define RB532_BTN_KSYM BTN_0
|
|
|
|
/* The S1 button state is provided by GPIO pin 1. But as this
|
|
* pin is also used for uart input as alternate function, the
|
|
* operational modes must be switched first:
|
|
* 1) disable uart using set_latch_u5()
|
|
* 2) turn off alternate function implicitly through
|
|
* gpio_direction_input()
|
|
* 3) read the GPIO's current value
|
|
* 4) undo step 2 by enabling alternate function (in this
|
|
* mode the GPIO direction is fixed, so no change needed)
|
|
* 5) turn on uart again
|
|
* The GPIO value occurs to be inverted, so pin high means
|
|
* button is not pressed.
|
|
*/
|
|
static bool rb532_button_pressed(void)
|
|
{
|
|
int val;
|
|
|
|
set_latch_u5(0, LO_FOFF);
|
|
gpio_direction_input(GPIO_BTN_S1);
|
|
|
|
val = gpio_get_value(GPIO_BTN_S1);
|
|
|
|
rb532_gpio_set_func(GPIO_BTN_S1);
|
|
set_latch_u5(LO_FOFF, 0);
|
|
|
|
return !val;
|
|
}
|
|
|
|
static void rb532_button_poll(struct input_polled_dev *poll_dev)
|
|
{
|
|
input_report_key(poll_dev->input, RB532_BTN_KSYM,
|
|
rb532_button_pressed());
|
|
input_sync(poll_dev->input);
|
|
}
|
|
|
|
static int __devinit rb532_button_probe(struct platform_device *pdev)
|
|
{
|
|
struct input_polled_dev *poll_dev;
|
|
int error;
|
|
|
|
poll_dev = input_allocate_polled_device();
|
|
if (!poll_dev)
|
|
return -ENOMEM;
|
|
|
|
poll_dev->poll = rb532_button_poll;
|
|
poll_dev->poll_interval = RB532_BTN_RATE;
|
|
|
|
poll_dev->input->name = "rb532 button";
|
|
poll_dev->input->phys = "rb532/button0";
|
|
poll_dev->input->id.bustype = BUS_HOST;
|
|
poll_dev->input->dev.parent = &pdev->dev;
|
|
|
|
dev_set_drvdata(&pdev->dev, poll_dev);
|
|
|
|
input_set_capability(poll_dev->input, EV_KEY, RB532_BTN_KSYM);
|
|
|
|
error = input_register_polled_device(poll_dev);
|
|
if (error) {
|
|
input_free_polled_device(poll_dev);
|
|
return error;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __devexit rb532_button_remove(struct platform_device *pdev)
|
|
{
|
|
struct input_polled_dev *poll_dev = dev_get_drvdata(&pdev->dev);
|
|
|
|
input_unregister_polled_device(poll_dev);
|
|
input_free_polled_device(poll_dev);
|
|
dev_set_drvdata(&pdev->dev, NULL);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct platform_driver rb532_button_driver = {
|
|
.probe = rb532_button_probe,
|
|
.remove = __devexit_p(rb532_button_remove),
|
|
.driver = {
|
|
.name = DRV_NAME,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
};
|
|
|
|
static int __init rb532_button_init(void)
|
|
{
|
|
return platform_driver_register(&rb532_button_driver);
|
|
}
|
|
|
|
static void __exit rb532_button_exit(void)
|
|
{
|
|
platform_driver_unregister(&rb532_button_driver);
|
|
}
|
|
|
|
module_init(rb532_button_init);
|
|
module_exit(rb532_button_exit);
|
|
|
|
MODULE_AUTHOR("Phil Sutter <n0-1@freewrt.org>");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_DESCRIPTION("Support for S1 button on Routerboard 532");
|
|
MODULE_ALIAS("platform:" DRV_NAME);
|