linux/drivers/serial/8250.h
Adrian Bunk d87a6d951c drivers/serial/: remove CVS keywords
This patch removes CVS keywords that weren't updated for a long time in
comments, printk's and MODULE_DESCRIPTION's (no printk's or
MODULE_DESCRIPTION's are completely removed).

While doing this I also found and fixed a missing \n in a printk
in m32r_sio.c

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-20 17:12:35 -07:00

79 lines
2.3 KiB
C

/*
* linux/drivers/char/8250.h
*
* Driver for 8250/16550-type serial ports
*
* Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
*
* Copyright (C) 2001 Russell King.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/serial_8250.h>
struct old_serial_port {
unsigned int uart;
unsigned int baud_base;
unsigned int port;
unsigned int irq;
unsigned int flags;
unsigned char hub6;
unsigned char io_type;
unsigned char *iomem_base;
unsigned short iomem_reg_shift;
};
/*
* This replaces serial_uart_config in include/linux/serial.h
*/
struct serial8250_config {
const char *name;
unsigned short fifo_size;
unsigned short tx_loadsz;
unsigned char fcr;
unsigned int flags;
};
#define UART_CAP_FIFO (1 << 8) /* UART has FIFO */
#define UART_CAP_EFR (1 << 9) /* UART has EFR */
#define UART_CAP_SLEEP (1 << 10) /* UART has IER sleep */
#define UART_CAP_AFE (1 << 11) /* MCR-based hw flow control */
#define UART_CAP_UUE (1 << 12) /* UART needs IER bit 6 set (Xscale) */
#define UART_BUG_QUOT (1 << 0) /* UART has buggy quot LSB */
#define UART_BUG_TXEN (1 << 1) /* UART has buggy TX IIR status */
#define UART_BUG_NOMSR (1 << 2) /* UART has buggy MSR status bits (Au1x00) */
#define PROBE_RSA (1 << 0)
#define PROBE_ANY (~0)
#define HIGH_BITS_OFFSET ((sizeof(long)-sizeof(int))*8)
#ifdef CONFIG_SERIAL_8250_SHARE_IRQ
#define SERIAL8250_SHARE_IRQS 1
#else
#define SERIAL8250_SHARE_IRQS 0
#endif
#if defined(__alpha__) && !defined(CONFIG_PCI)
/*
* Digital did something really horribly wrong with the OUT1 and OUT2
* lines on at least some ALPHA's. The failure mode is that if either
* is cleared, the machine locks up with endless interrupts.
*/
#define ALPHA_KLUDGE_MCR (UART_MCR_OUT2 | UART_MCR_OUT1)
#elif defined(CONFIG_SBC8560)
/*
* WindRiver did something similarly broken on their SBC8560 board. The
* UART tristates its IRQ output while OUT2 is clear, but they pulled
* the interrupt line _up_ instead of down, so if we register the IRQ
* while the UART is in that state, we die in an IRQ storm. */
#define ALPHA_KLUDGE_MCR (UART_MCR_OUT2)
#else
#define ALPHA_KLUDGE_MCR 0
#endif