linux/drivers/net/fddi/Kconfig
Jeff Kirsher 33f810b203 fddi: Move the FDDI drivers
Move the FDDI drivers into drivers/net/fddi/ and make the
necessary Kconfig and Makefile changes.

CC: "Maciej W. Rozycki" <macro@linux-mips.org>
CC: Christoph Goos <cgoos@syskonnect.de>
CC: <linux@syskonnect.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-08-27 00:58:13 -07:00

78 lines
2.4 KiB
Plaintext

#
# FDDI network device configuration
#
config FDDI
tristate "FDDI driver support"
depends on PCI || EISA || TC
---help---
Fiber Distributed Data Interface is a high speed local area network
design; essentially a replacement for high speed Ethernet. FDDI can
run over copper or fiber. If you are connected to such a network and
want a driver for the FDDI card in your computer, say Y here (and
then also Y to the driver for your FDDI card, below). Most people
will say N.
if FDDI
config DEFXX
tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
depends on FDDI && (PCI || EISA || TC)
---help---
This is support for the DIGITAL series of TURBOchannel (DEFTA),
EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
to a local FDDI network.
To compile this driver as a module, choose M here: the module
will be called defxx. If unsure, say N.
config DEFXX_MMIO
bool
prompt "Use MMIO instead of PIO" if PCI || EISA
depends on DEFXX
default n if PCI || EISA
default y
---help---
This instructs the driver to use EISA or PCI memory-mapped I/O
(MMIO) as appropriate instead of programmed I/O ports (PIO).
Enabling this gives an improvement in processing time in parts
of the driver, but it may cause problems with EISA (DEFEA)
adapters. TURBOchannel does not have the concept of I/O ports,
so MMIO is always used for these (DEFTA) adapters.
If unsure, say N.
config SKFP
tristate "SysKonnect FDDI PCI support"
depends on FDDI && PCI
select BITREVERSE
---help---
Say Y here if you have a SysKonnect FDDI PCI adapter.
The following adapters are supported by this driver:
- SK-5521 (SK-NET FDDI-UP)
- SK-5522 (SK-NET FDDI-UP DAS)
- SK-5541 (SK-NET FDDI-FP)
- SK-5543 (SK-NET FDDI-LP)
- SK-5544 (SK-NET FDDI-LP DAS)
- SK-5821 (SK-NET FDDI-UP64)
- SK-5822 (SK-NET FDDI-UP64 DAS)
- SK-5841 (SK-NET FDDI-FP64)
- SK-5843 (SK-NET FDDI-LP64)
- SK-5844 (SK-NET FDDI-LP64 DAS)
- Netelligent 100 FDDI DAS Fibre SC
- Netelligent 100 FDDI SAS Fibre SC
- Netelligent 100 FDDI DAS UTP
- Netelligent 100 FDDI SAS UTP
- Netelligent 100 FDDI SAS Fibre MIC
Read <file:Documentation/networking/skfp.txt> for information about
the driver.
Questions concerning this driver can be addressed to:
<linux@syskonnect.de>
To compile this driver as a module, choose M here: the module
will be called skfp. This is recommended.
endif # FDDI