mirror of
https://github.com/torvalds/linux.git
synced 2024-11-10 14:11:52 +00:00
8d668bad7a
After issuing a "poweroff" command the board goes through the expected power-off sequence and turns it off completely: systemd-shutdown[1]: Powering off. imx2-wdt 30280000.watchdog: Device shutdown: Expect reboot! reboot: Power down The "Expect reboot!" message is misleading because in the power-off case, no reboot is expected to happen at all. Avoid the confusion by removing the "Expect reboot!" message. Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20230822135255.1013981-1-festevam@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
490 lines
14 KiB
C
490 lines
14 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Watchdog driver for IMX2 and later processors
|
|
*
|
|
* Copyright (C) 2010 Wolfram Sang, Pengutronix e.K. <kernel@pengutronix.de>
|
|
* Copyright (C) 2014 Freescale Semiconductor, Inc.
|
|
*
|
|
* some parts adapted by similar drivers from Darius Augulis and Vladimir
|
|
* Zapolskiy, additional improvements by Wim Van Sebroeck.
|
|
*
|
|
* NOTE: MX1 has a slightly different Watchdog than MX2 and later:
|
|
*
|
|
* MX1: MX2+:
|
|
* ---- -----
|
|
* Registers: 32-bit 16-bit
|
|
* Stopable timer: Yes No
|
|
* Need to enable clk: No Yes
|
|
* Halt on suspend: Manual Can be automatic
|
|
*/
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/init.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/io.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/moduleparam.h>
|
|
#include <linux/of.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/watchdog.h>
|
|
|
|
#define DRIVER_NAME "imx2-wdt"
|
|
|
|
#define IMX2_WDT_WCR 0x00 /* Control Register */
|
|
#define IMX2_WDT_WCR_WT (0xFF << 8) /* -> Watchdog Timeout Field */
|
|
#define IMX2_WDT_WCR_WDW BIT(7) /* -> Watchdog disable for WAIT */
|
|
#define IMX2_WDT_WCR_WDA BIT(5) /* -> External Reset WDOG_B */
|
|
#define IMX2_WDT_WCR_SRS BIT(4) /* -> Software Reset Signal */
|
|
#define IMX2_WDT_WCR_WRE BIT(3) /* -> WDOG Reset Enable */
|
|
#define IMX2_WDT_WCR_WDE BIT(2) /* -> Watchdog Enable */
|
|
#define IMX2_WDT_WCR_WDZST BIT(0) /* -> Watchdog timer Suspend */
|
|
|
|
#define IMX2_WDT_WSR 0x02 /* Service Register */
|
|
#define IMX2_WDT_SEQ1 0x5555 /* -> service sequence 1 */
|
|
#define IMX2_WDT_SEQ2 0xAAAA /* -> service sequence 2 */
|
|
|
|
#define IMX2_WDT_WRSR 0x04 /* Reset Status Register */
|
|
#define IMX2_WDT_WRSR_TOUT BIT(1) /* -> Reset due to Timeout */
|
|
|
|
#define IMX2_WDT_WICR 0x06 /* Interrupt Control Register */
|
|
#define IMX2_WDT_WICR_WIE BIT(15) /* -> Interrupt Enable */
|
|
#define IMX2_WDT_WICR_WTIS BIT(14) /* -> Interrupt Status */
|
|
#define IMX2_WDT_WICR_WICT 0xFF /* -> Interrupt Count Timeout */
|
|
|
|
#define IMX2_WDT_WMCR 0x08 /* Misc Register */
|
|
|
|
#define IMX2_WDT_MAX_TIME 128U
|
|
#define IMX2_WDT_DEFAULT_TIME 60 /* in seconds */
|
|
|
|
#define WDOG_SEC_TO_COUNT(s) ((s * 2 - 1) << 8)
|
|
|
|
struct imx2_wdt_data {
|
|
bool wdw_supported;
|
|
};
|
|
|
|
struct imx2_wdt_device {
|
|
struct clk *clk;
|
|
struct regmap *regmap;
|
|
struct watchdog_device wdog;
|
|
const struct imx2_wdt_data *data;
|
|
bool ext_reset;
|
|
bool clk_is_on;
|
|
bool no_ping;
|
|
bool sleep_wait;
|
|
};
|
|
|
|
static bool nowayout = WATCHDOG_NOWAYOUT;
|
|
module_param(nowayout, bool, 0);
|
|
MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default="
|
|
__MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
|
|
|
|
static unsigned timeout;
|
|
module_param(timeout, uint, 0);
|
|
MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds (default="
|
|
__MODULE_STRING(IMX2_WDT_DEFAULT_TIME) ")");
|
|
|
|
static const struct watchdog_info imx2_wdt_info = {
|
|
.identity = "imx2+ watchdog",
|
|
.options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
|
|
};
|
|
|
|
static const struct watchdog_info imx2_wdt_pretimeout_info = {
|
|
.identity = "imx2+ watchdog",
|
|
.options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE |
|
|
WDIOF_PRETIMEOUT,
|
|
};
|
|
|
|
static int imx2_wdt_restart(struct watchdog_device *wdog, unsigned long action,
|
|
void *data)
|
|
{
|
|
struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
|
|
unsigned int wcr_enable = IMX2_WDT_WCR_WDE;
|
|
|
|
/* Use internal reset or external - not both */
|
|
if (wdev->ext_reset)
|
|
wcr_enable |= IMX2_WDT_WCR_SRS; /* do not assert int reset */
|
|
else
|
|
wcr_enable |= IMX2_WDT_WCR_WDA; /* do not assert ext-reset */
|
|
|
|
/* Assert SRS signal */
|
|
regmap_write(wdev->regmap, IMX2_WDT_WCR, wcr_enable);
|
|
/*
|
|
* Due to imx6q errata ERR004346 (WDOG: WDOG SRS bit requires to be
|
|
* written twice), we add another two writes to ensure there must be at
|
|
* least two writes happen in the same one 32kHz clock period. We save
|
|
* the target check here, since the writes shouldn't be a huge burden
|
|
* for other platforms.
|
|
*/
|
|
regmap_write(wdev->regmap, IMX2_WDT_WCR, wcr_enable);
|
|
regmap_write(wdev->regmap, IMX2_WDT_WCR, wcr_enable);
|
|
|
|
/* wait for reset to assert... */
|
|
mdelay(500);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static inline void imx2_wdt_setup(struct watchdog_device *wdog)
|
|
{
|
|
struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
|
|
u32 val;
|
|
|
|
regmap_read(wdev->regmap, IMX2_WDT_WCR, &val);
|
|
|
|
/* Suspend timer in low power mode, write once-only */
|
|
val |= IMX2_WDT_WCR_WDZST;
|
|
/* Suspend timer in low power WAIT mode, write once-only */
|
|
if (wdev->sleep_wait)
|
|
val |= IMX2_WDT_WCR_WDW;
|
|
/* Strip the old watchdog Time-Out value */
|
|
val &= ~IMX2_WDT_WCR_WT;
|
|
/* Generate internal chip-level reset if WDOG times out */
|
|
if (!wdev->ext_reset)
|
|
val &= ~IMX2_WDT_WCR_WRE;
|
|
/* Or if external-reset assert WDOG_B reset only on time-out */
|
|
else
|
|
val |= IMX2_WDT_WCR_WRE;
|
|
/* Keep Watchdog Disabled */
|
|
val &= ~IMX2_WDT_WCR_WDE;
|
|
/* Set the watchdog's Time-Out value */
|
|
val |= WDOG_SEC_TO_COUNT(wdog->timeout);
|
|
|
|
regmap_write(wdev->regmap, IMX2_WDT_WCR, val);
|
|
|
|
/* enable the watchdog */
|
|
val |= IMX2_WDT_WCR_WDE;
|
|
regmap_write(wdev->regmap, IMX2_WDT_WCR, val);
|
|
}
|
|
|
|
static inline bool imx2_wdt_is_running(struct imx2_wdt_device *wdev)
|
|
{
|
|
u32 val;
|
|
|
|
regmap_read(wdev->regmap, IMX2_WDT_WCR, &val);
|
|
|
|
return val & IMX2_WDT_WCR_WDE;
|
|
}
|
|
|
|
static int imx2_wdt_ping(struct watchdog_device *wdog)
|
|
{
|
|
struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
|
|
|
|
if (!wdev->clk_is_on)
|
|
return 0;
|
|
|
|
regmap_write(wdev->regmap, IMX2_WDT_WSR, IMX2_WDT_SEQ1);
|
|
regmap_write(wdev->regmap, IMX2_WDT_WSR, IMX2_WDT_SEQ2);
|
|
return 0;
|
|
}
|
|
|
|
static void __imx2_wdt_set_timeout(struct watchdog_device *wdog,
|
|
unsigned int new_timeout)
|
|
{
|
|
struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
|
|
|
|
regmap_update_bits(wdev->regmap, IMX2_WDT_WCR, IMX2_WDT_WCR_WT,
|
|
WDOG_SEC_TO_COUNT(new_timeout));
|
|
}
|
|
|
|
static int imx2_wdt_set_timeout(struct watchdog_device *wdog,
|
|
unsigned int new_timeout)
|
|
{
|
|
unsigned int actual;
|
|
|
|
actual = min(new_timeout, IMX2_WDT_MAX_TIME);
|
|
__imx2_wdt_set_timeout(wdog, actual);
|
|
wdog->timeout = new_timeout;
|
|
return 0;
|
|
}
|
|
|
|
static int imx2_wdt_set_pretimeout(struct watchdog_device *wdog,
|
|
unsigned int new_pretimeout)
|
|
{
|
|
struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
|
|
|
|
if (new_pretimeout >= IMX2_WDT_MAX_TIME)
|
|
return -EINVAL;
|
|
|
|
wdog->pretimeout = new_pretimeout;
|
|
|
|
regmap_update_bits(wdev->regmap, IMX2_WDT_WICR,
|
|
IMX2_WDT_WICR_WIE | IMX2_WDT_WICR_WICT,
|
|
IMX2_WDT_WICR_WIE | (new_pretimeout << 1));
|
|
return 0;
|
|
}
|
|
|
|
static irqreturn_t imx2_wdt_isr(int irq, void *wdog_arg)
|
|
{
|
|
struct watchdog_device *wdog = wdog_arg;
|
|
struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
|
|
|
|
regmap_write_bits(wdev->regmap, IMX2_WDT_WICR,
|
|
IMX2_WDT_WICR_WTIS, IMX2_WDT_WICR_WTIS);
|
|
|
|
watchdog_notify_pretimeout(wdog);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int imx2_wdt_start(struct watchdog_device *wdog)
|
|
{
|
|
struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
|
|
|
|
if (imx2_wdt_is_running(wdev))
|
|
imx2_wdt_set_timeout(wdog, wdog->timeout);
|
|
else
|
|
imx2_wdt_setup(wdog);
|
|
|
|
set_bit(WDOG_HW_RUNNING, &wdog->status);
|
|
|
|
return imx2_wdt_ping(wdog);
|
|
}
|
|
|
|
static const struct watchdog_ops imx2_wdt_ops = {
|
|
.owner = THIS_MODULE,
|
|
.start = imx2_wdt_start,
|
|
.ping = imx2_wdt_ping,
|
|
.set_timeout = imx2_wdt_set_timeout,
|
|
.set_pretimeout = imx2_wdt_set_pretimeout,
|
|
.restart = imx2_wdt_restart,
|
|
};
|
|
|
|
static const struct regmap_config imx2_wdt_regmap_config = {
|
|
.reg_bits = 16,
|
|
.reg_stride = 2,
|
|
.val_bits = 16,
|
|
.max_register = 0x8,
|
|
};
|
|
|
|
static void imx2_wdt_action(void *data)
|
|
{
|
|
clk_disable_unprepare(data);
|
|
}
|
|
|
|
static int __init imx2_wdt_probe(struct platform_device *pdev)
|
|
{
|
|
struct device *dev = &pdev->dev;
|
|
struct imx2_wdt_device *wdev;
|
|
struct watchdog_device *wdog;
|
|
void __iomem *base;
|
|
int ret;
|
|
u32 val;
|
|
|
|
wdev = devm_kzalloc(dev, sizeof(*wdev), GFP_KERNEL);
|
|
if (!wdev)
|
|
return -ENOMEM;
|
|
|
|
base = devm_platform_ioremap_resource(pdev, 0);
|
|
if (IS_ERR(base))
|
|
return PTR_ERR(base);
|
|
|
|
wdev->regmap = devm_regmap_init_mmio_clk(dev, NULL, base,
|
|
&imx2_wdt_regmap_config);
|
|
if (IS_ERR(wdev->regmap)) {
|
|
dev_err(dev, "regmap init failed\n");
|
|
return PTR_ERR(wdev->regmap);
|
|
}
|
|
|
|
wdev->clk = devm_clk_get(dev, NULL);
|
|
if (IS_ERR(wdev->clk)) {
|
|
dev_err(dev, "can't get Watchdog clock\n");
|
|
return PTR_ERR(wdev->clk);
|
|
}
|
|
|
|
wdog = &wdev->wdog;
|
|
wdog->info = &imx2_wdt_info;
|
|
wdog->ops = &imx2_wdt_ops;
|
|
wdog->min_timeout = 1;
|
|
wdog->timeout = IMX2_WDT_DEFAULT_TIME;
|
|
wdog->max_hw_heartbeat_ms = IMX2_WDT_MAX_TIME * 1000;
|
|
wdog->parent = dev;
|
|
|
|
wdev->data = of_device_get_match_data(dev);
|
|
|
|
ret = platform_get_irq(pdev, 0);
|
|
if (ret > 0)
|
|
if (!devm_request_irq(dev, ret, imx2_wdt_isr, 0,
|
|
dev_name(dev), wdog))
|
|
wdog->info = &imx2_wdt_pretimeout_info;
|
|
|
|
ret = clk_prepare_enable(wdev->clk);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = devm_add_action_or_reset(dev, imx2_wdt_action, wdev->clk);
|
|
if (ret)
|
|
return ret;
|
|
|
|
wdev->clk_is_on = true;
|
|
|
|
regmap_read(wdev->regmap, IMX2_WDT_WRSR, &val);
|
|
wdog->bootstatus = val & IMX2_WDT_WRSR_TOUT ? WDIOF_CARDRESET : 0;
|
|
|
|
wdev->ext_reset = of_property_read_bool(dev->of_node,
|
|
"fsl,ext-reset-output");
|
|
|
|
if (of_property_read_bool(dev->of_node, "fsl,suspend-in-wait")) {
|
|
if (!wdev->data->wdw_supported) {
|
|
dev_err(dev, "suspend-in-wait not supported\n");
|
|
return -EINVAL;
|
|
}
|
|
wdev->sleep_wait = true;
|
|
}
|
|
|
|
/*
|
|
* The i.MX7D doesn't support low power mode, so we need to ping the watchdog
|
|
* during suspend. Interaction with "fsl,suspend-in-wait" is unknown!
|
|
*/
|
|
wdev->no_ping = !of_device_is_compatible(dev->of_node, "fsl,imx7d-wdt");
|
|
platform_set_drvdata(pdev, wdog);
|
|
watchdog_set_drvdata(wdog, wdev);
|
|
watchdog_set_nowayout(wdog, nowayout);
|
|
watchdog_set_restart_priority(wdog, 128);
|
|
watchdog_init_timeout(wdog, timeout, dev);
|
|
if (wdev->no_ping)
|
|
watchdog_stop_ping_on_suspend(wdog);
|
|
|
|
if (imx2_wdt_is_running(wdev)) {
|
|
imx2_wdt_set_timeout(wdog, wdog->timeout);
|
|
set_bit(WDOG_HW_RUNNING, &wdog->status);
|
|
}
|
|
|
|
/*
|
|
* Disable the watchdog power down counter at boot. Otherwise the power
|
|
* down counter will pull down the #WDOG interrupt line for one clock
|
|
* cycle.
|
|
*/
|
|
regmap_write(wdev->regmap, IMX2_WDT_WMCR, 0);
|
|
|
|
return devm_watchdog_register_device(dev, wdog);
|
|
}
|
|
|
|
static void imx2_wdt_shutdown(struct platform_device *pdev)
|
|
{
|
|
struct watchdog_device *wdog = platform_get_drvdata(pdev);
|
|
struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
|
|
|
|
if (imx2_wdt_is_running(wdev)) {
|
|
/*
|
|
* We are running, configure max timeout before reboot
|
|
* will take place.
|
|
*/
|
|
imx2_wdt_set_timeout(wdog, IMX2_WDT_MAX_TIME);
|
|
imx2_wdt_ping(wdog);
|
|
dev_crit(&pdev->dev, "Device shutdown.\n");
|
|
}
|
|
}
|
|
|
|
/* Disable watchdog if it is active or non-active but still running */
|
|
static int __maybe_unused imx2_wdt_suspend(struct device *dev)
|
|
{
|
|
struct watchdog_device *wdog = dev_get_drvdata(dev);
|
|
struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
|
|
|
|
/* The watchdog IP block is running */
|
|
if (imx2_wdt_is_running(wdev)) {
|
|
/*
|
|
* Don't update wdog->timeout, we'll restore the current value
|
|
* during resume.
|
|
*/
|
|
__imx2_wdt_set_timeout(wdog, IMX2_WDT_MAX_TIME);
|
|
imx2_wdt_ping(wdog);
|
|
}
|
|
|
|
if (wdev->no_ping) {
|
|
clk_disable_unprepare(wdev->clk);
|
|
|
|
wdev->clk_is_on = false;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Enable watchdog and configure it if necessary */
|
|
static int __maybe_unused imx2_wdt_resume(struct device *dev)
|
|
{
|
|
struct watchdog_device *wdog = dev_get_drvdata(dev);
|
|
struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
|
|
int ret;
|
|
|
|
if (wdev->no_ping) {
|
|
ret = clk_prepare_enable(wdev->clk);
|
|
|
|
if (ret)
|
|
return ret;
|
|
|
|
wdev->clk_is_on = true;
|
|
}
|
|
|
|
if (watchdog_active(wdog) && !imx2_wdt_is_running(wdev)) {
|
|
/*
|
|
* If the watchdog is still active and resumes
|
|
* from deep sleep state, need to restart the
|
|
* watchdog again.
|
|
*/
|
|
imx2_wdt_setup(wdog);
|
|
}
|
|
if (imx2_wdt_is_running(wdev)) {
|
|
imx2_wdt_set_timeout(wdog, wdog->timeout);
|
|
imx2_wdt_ping(wdog);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static SIMPLE_DEV_PM_OPS(imx2_wdt_pm_ops, imx2_wdt_suspend,
|
|
imx2_wdt_resume);
|
|
|
|
static struct imx2_wdt_data imx_wdt = {
|
|
.wdw_supported = true,
|
|
};
|
|
|
|
static struct imx2_wdt_data imx_wdt_legacy = {
|
|
.wdw_supported = false,
|
|
};
|
|
|
|
static const struct of_device_id imx2_wdt_dt_ids[] = {
|
|
{ .compatible = "fsl,imx21-wdt", .data = &imx_wdt_legacy },
|
|
{ .compatible = "fsl,imx25-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx27-wdt", .data = &imx_wdt_legacy },
|
|
{ .compatible = "fsl,imx31-wdt", .data = &imx_wdt_legacy },
|
|
{ .compatible = "fsl,imx35-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx50-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx51-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx53-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx6q-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx6sl-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx6sll-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx6sx-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx6ul-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx7d-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx8mm-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx8mn-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx8mp-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,imx8mq-wdt", .data = &imx_wdt },
|
|
{ .compatible = "fsl,ls1012a-wdt", .data = &imx_wdt_legacy },
|
|
{ .compatible = "fsl,ls1043a-wdt", .data = &imx_wdt_legacy },
|
|
{ .compatible = "fsl,vf610-wdt", .data = &imx_wdt },
|
|
{ /* sentinel */ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, imx2_wdt_dt_ids);
|
|
|
|
static struct platform_driver imx2_wdt_driver = {
|
|
.shutdown = imx2_wdt_shutdown,
|
|
.driver = {
|
|
.name = DRIVER_NAME,
|
|
.pm = &imx2_wdt_pm_ops,
|
|
.of_match_table = imx2_wdt_dt_ids,
|
|
},
|
|
};
|
|
|
|
module_platform_driver_probe(imx2_wdt_driver, imx2_wdt_probe);
|
|
|
|
MODULE_AUTHOR("Wolfram Sang");
|
|
MODULE_DESCRIPTION("Watchdog driver for IMX2 and later");
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_ALIAS("platform:" DRIVER_NAME);
|