mirror of
https://github.com/torvalds/linux.git
synced 2024-12-30 14:52:05 +00:00
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
117 lines
4.9 KiB
Plaintext
117 lines
4.9 KiB
Plaintext
In Linux 2.5 kernels (and later), USB device drivers have additional control
|
|
over how DMA may be used to perform I/O operations. The APIs are detailed
|
|
in the kernel usb programming guide (kerneldoc, from the source code).
|
|
|
|
|
|
API OVERVIEW
|
|
|
|
The big picture is that USB drivers can continue to ignore most DMA issues,
|
|
though they still must provide DMA-ready buffers (see DMA-mapping.txt).
|
|
That's how they've worked through the 2.4 (and earlier) kernels.
|
|
|
|
OR: they can now be DMA-aware.
|
|
|
|
- New calls enable DMA-aware drivers, letting them allocate dma buffers and
|
|
manage dma mappings for existing dma-ready buffers (see below).
|
|
|
|
- URBs have an additional "transfer_dma" field, as well as a transfer_flags
|
|
bit saying if it's valid. (Control requests also have "setup_dma" and a
|
|
corresponding transfer_flags bit.)
|
|
|
|
- "usbcore" will map those DMA addresses, if a DMA-aware driver didn't do
|
|
it first and set URB_NO_TRANSFER_DMA_MAP or URB_NO_SETUP_DMA_MAP. HCDs
|
|
don't manage dma mappings for URBs.
|
|
|
|
- There's a new "generic DMA API", parts of which are usable by USB device
|
|
drivers. Never use dma_set_mask() on any USB interface or device; that
|
|
would potentially break all devices sharing that bus.
|
|
|
|
|
|
ELIMINATING COPIES
|
|
|
|
It's good to avoid making CPUs copy data needlessly. The costs can add up,
|
|
and effects like cache-trashing can impose subtle penalties.
|
|
|
|
- When you're allocating a buffer for DMA purposes anyway, use the buffer
|
|
primitives. Think of them as kmalloc and kfree that give you the right
|
|
kind of addresses to store in urb->transfer_buffer and urb->transfer_dma,
|
|
while guaranteeing that no hidden copies through DMA "bounce" buffers will
|
|
slow things down. You'd also set URB_NO_TRANSFER_DMA_MAP in
|
|
urb->transfer_flags:
|
|
|
|
void *usb_buffer_alloc (struct usb_device *dev, size_t size,
|
|
int mem_flags, dma_addr_t *dma);
|
|
|
|
void usb_buffer_free (struct usb_device *dev, size_t size,
|
|
void *addr, dma_addr_t dma);
|
|
|
|
For control transfers you can use the buffer primitives or not for each
|
|
of the transfer buffer and setup buffer independently. Set the flag bits
|
|
URB_NO_TRANSFER_DMA_MAP and URB_NO_SETUP_DMA_MAP to indicate which
|
|
buffers you have prepared. For non-control transfers URB_NO_SETUP_DMA_MAP
|
|
is ignored.
|
|
|
|
The memory buffer returned is "dma-coherent"; sometimes you might need to
|
|
force a consistent memory access ordering by using memory barriers. It's
|
|
not using a streaming DMA mapping, so it's good for small transfers on
|
|
systems where the I/O would otherwise tie up an IOMMU mapping. (See
|
|
Documentation/DMA-mapping.txt for definitions of "coherent" and "streaming"
|
|
DMA mappings.)
|
|
|
|
Asking for 1/Nth of a page (as well as asking for N pages) is reasonably
|
|
space-efficient.
|
|
|
|
- Devices on some EHCI controllers could handle DMA to/from high memory.
|
|
Driver probe() routines can notice this using a generic DMA call, then
|
|
tell higher level code (network, scsi, etc) about it like this:
|
|
|
|
if (dma_supported (&intf->dev, 0xffffffffffffffffULL))
|
|
net->features |= NETIF_F_HIGHDMA;
|
|
|
|
That can eliminate dma bounce buffering of requests that originate (or
|
|
terminate) in high memory, in cases where the buffers aren't allocated
|
|
with usb_buffer_alloc() but instead are dma-mapped.
|
|
|
|
|
|
WORKING WITH EXISTING BUFFERS
|
|
|
|
Existing buffers aren't usable for DMA without first being mapped into the
|
|
DMA address space of the device.
|
|
|
|
- When you're using scatterlists, you can map everything at once. On some
|
|
systems, this kicks in an IOMMU and turns the scatterlists into single
|
|
DMA transactions:
|
|
|
|
int usb_buffer_map_sg (struct usb_device *dev, unsigned pipe,
|
|
struct scatterlist *sg, int nents);
|
|
|
|
void usb_buffer_dmasync_sg (struct usb_device *dev, unsigned pipe,
|
|
struct scatterlist *sg, int n_hw_ents);
|
|
|
|
void usb_buffer_unmap_sg (struct usb_device *dev, unsigned pipe,
|
|
struct scatterlist *sg, int n_hw_ents);
|
|
|
|
It's probably easier to use the new usb_sg_*() calls, which do the DMA
|
|
mapping and apply other tweaks to make scatterlist i/o be fast.
|
|
|
|
- Some drivers may prefer to work with the model that they're mapping large
|
|
buffers, synchronizing their safe re-use. (If there's no re-use, then let
|
|
usbcore do the map/unmap.) Large periodic transfers make good examples
|
|
here, since it's cheaper to just synchronize the buffer than to unmap it
|
|
each time an urb completes and then re-map it on during resubmission.
|
|
|
|
These calls all work with initialized urbs: urb->dev, urb->pipe,
|
|
urb->transfer_buffer, and urb->transfer_buffer_length must all be
|
|
valid when these calls are used (urb->setup_packet must be valid too
|
|
if urb is a control request):
|
|
|
|
struct urb *usb_buffer_map (struct urb *urb);
|
|
|
|
void usb_buffer_dmasync (struct urb *urb);
|
|
|
|
void usb_buffer_unmap (struct urb *urb);
|
|
|
|
The calls manage urb->transfer_dma for you, and set URB_NO_TRANSFER_DMA_MAP
|
|
so that usbcore won't map or unmap the buffer. The same goes for
|
|
urb->setup_dma and URB_NO_SETUP_DMA_MAP for control requests.
|