mirror of
https://github.com/torvalds/linux.git
synced 2024-11-10 06:01:57 +00:00
87dd04f9b1
It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. Convert reading boolean properties to to of_property_read_bool(). Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230310144702.1541660-1-robh@kernel.org
853 lines
22 KiB
C
853 lines
22 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
#include <linux/clk.h>
|
|
#include <linux/clocksource.h>
|
|
#include <linux/clockchips.h>
|
|
#include <linux/cpuhotplug.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/io.h>
|
|
#include <linux/iopoll.h>
|
|
#include <linux/err.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_address.h>
|
|
#include <linux/of_irq.h>
|
|
#include <linux/sched_clock.h>
|
|
|
|
#include <linux/clk/clk-conf.h>
|
|
|
|
#include <clocksource/timer-ti-dm.h>
|
|
#include <dt-bindings/bus/ti-sysc.h>
|
|
|
|
/* For type1, set SYSC_OMAP2_CLOCKACTIVITY for fck off on idle, l4 clock on */
|
|
#define DMTIMER_TYPE1_ENABLE ((1 << 9) | (SYSC_IDLE_SMART << 3) | \
|
|
SYSC_OMAP2_ENAWAKEUP | SYSC_OMAP2_AUTOIDLE)
|
|
#define DMTIMER_TYPE1_DISABLE (SYSC_OMAP2_SOFTRESET | SYSC_OMAP2_AUTOIDLE)
|
|
#define DMTIMER_TYPE2_ENABLE (SYSC_IDLE_SMART_WKUP << 2)
|
|
#define DMTIMER_RESET_WAIT 100000
|
|
|
|
#define DMTIMER_INST_DONT_CARE ~0U
|
|
|
|
static int counter_32k;
|
|
static u32 clocksource;
|
|
static u32 clockevent;
|
|
|
|
/*
|
|
* Subset of the timer registers we use. Note that the register offsets
|
|
* depend on the timer revision detected.
|
|
*/
|
|
struct dmtimer_systimer {
|
|
void __iomem *base;
|
|
u8 sysc;
|
|
u8 irq_stat;
|
|
u8 irq_ena;
|
|
u8 pend;
|
|
u8 load;
|
|
u8 counter;
|
|
u8 ctrl;
|
|
u8 wakeup;
|
|
u8 ifctrl;
|
|
struct clk *fck;
|
|
struct clk *ick;
|
|
unsigned long rate;
|
|
};
|
|
|
|
struct dmtimer_clockevent {
|
|
struct clock_event_device dev;
|
|
struct dmtimer_systimer t;
|
|
u32 period;
|
|
};
|
|
|
|
struct dmtimer_clocksource {
|
|
struct clocksource dev;
|
|
struct dmtimer_systimer t;
|
|
unsigned int loadval;
|
|
};
|
|
|
|
/* Assumes v1 ip if bits [31:16] are zero */
|
|
static bool dmtimer_systimer_revision1(struct dmtimer_systimer *t)
|
|
{
|
|
u32 tidr = readl_relaxed(t->base);
|
|
|
|
return !(tidr >> 16);
|
|
}
|
|
|
|
static void dmtimer_systimer_enable(struct dmtimer_systimer *t)
|
|
{
|
|
u32 val;
|
|
|
|
if (dmtimer_systimer_revision1(t))
|
|
val = DMTIMER_TYPE1_ENABLE;
|
|
else
|
|
val = DMTIMER_TYPE2_ENABLE;
|
|
|
|
writel_relaxed(val, t->base + t->sysc);
|
|
}
|
|
|
|
static void dmtimer_systimer_disable(struct dmtimer_systimer *t)
|
|
{
|
|
if (!dmtimer_systimer_revision1(t))
|
|
return;
|
|
|
|
writel_relaxed(DMTIMER_TYPE1_DISABLE, t->base + t->sysc);
|
|
}
|
|
|
|
static int __init dmtimer_systimer_type1_reset(struct dmtimer_systimer *t)
|
|
{
|
|
void __iomem *syss = t->base + OMAP_TIMER_V1_SYS_STAT_OFFSET;
|
|
int ret;
|
|
u32 l;
|
|
|
|
dmtimer_systimer_enable(t);
|
|
writel_relaxed(BIT(1) | BIT(2), t->base + t->ifctrl);
|
|
ret = readl_poll_timeout_atomic(syss, l, l & BIT(0), 100,
|
|
DMTIMER_RESET_WAIT);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/* Note we must use io_base instead of func_base for type2 OCP regs */
|
|
static int __init dmtimer_systimer_type2_reset(struct dmtimer_systimer *t)
|
|
{
|
|
void __iomem *sysc = t->base + t->sysc;
|
|
u32 l;
|
|
|
|
dmtimer_systimer_enable(t);
|
|
l = readl_relaxed(sysc);
|
|
l |= BIT(0);
|
|
writel_relaxed(l, sysc);
|
|
|
|
return readl_poll_timeout_atomic(sysc, l, !(l & BIT(0)), 100,
|
|
DMTIMER_RESET_WAIT);
|
|
}
|
|
|
|
static int __init dmtimer_systimer_reset(struct dmtimer_systimer *t)
|
|
{
|
|
int ret;
|
|
|
|
if (dmtimer_systimer_revision1(t))
|
|
ret = dmtimer_systimer_type1_reset(t);
|
|
else
|
|
ret = dmtimer_systimer_type2_reset(t);
|
|
if (ret < 0) {
|
|
pr_err("%s failed with %i\n", __func__, ret);
|
|
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct of_device_id counter_match_table[] = {
|
|
{ .compatible = "ti,omap-counter32k" },
|
|
{ /* Sentinel */ },
|
|
};
|
|
|
|
/*
|
|
* Check if the SoC als has a usable working 32 KiHz counter. The 32 KiHz
|
|
* counter is handled by timer-ti-32k, but we need to detect it as it
|
|
* affects the preferred dmtimer system timer configuration. There is
|
|
* typically no use for a dmtimer clocksource if the 32 KiHz counter is
|
|
* present, except on am437x as described below.
|
|
*/
|
|
static void __init dmtimer_systimer_check_counter32k(void)
|
|
{
|
|
struct device_node *np;
|
|
|
|
if (counter_32k)
|
|
return;
|
|
|
|
np = of_find_matching_node(NULL, counter_match_table);
|
|
if (!np) {
|
|
counter_32k = -ENODEV;
|
|
|
|
return;
|
|
}
|
|
|
|
if (of_device_is_available(np))
|
|
counter_32k = 1;
|
|
else
|
|
counter_32k = -ENODEV;
|
|
|
|
of_node_put(np);
|
|
}
|
|
|
|
static const struct of_device_id dmtimer_match_table[] = {
|
|
{ .compatible = "ti,omap2420-timer", },
|
|
{ .compatible = "ti,omap3430-timer", },
|
|
{ .compatible = "ti,omap4430-timer", },
|
|
{ .compatible = "ti,omap5430-timer", },
|
|
{ .compatible = "ti,am335x-timer", },
|
|
{ .compatible = "ti,am335x-timer-1ms", },
|
|
{ .compatible = "ti,dm814-timer", },
|
|
{ .compatible = "ti,dm816-timer", },
|
|
{ /* Sentinel */ },
|
|
};
|
|
|
|
/*
|
|
* Checks that system timers are configured to not reset and idle during
|
|
* the generic timer-ti-dm device driver probe. And that the system timer
|
|
* source clocks are properly configured. Also, let's not hog any DSP and
|
|
* PWM capable timers unnecessarily as system timers.
|
|
*/
|
|
static bool __init dmtimer_is_preferred(struct device_node *np)
|
|
{
|
|
if (!of_device_is_available(np))
|
|
return false;
|
|
|
|
if (!of_property_read_bool(np->parent,
|
|
"ti,no-reset-on-init"))
|
|
return false;
|
|
|
|
if (!of_property_read_bool(np->parent, "ti,no-idle"))
|
|
return false;
|
|
|
|
/* Secure gptimer12 is always clocked with a fixed source */
|
|
if (!of_property_read_bool(np, "ti,timer-secure")) {
|
|
if (!of_property_read_bool(np, "assigned-clocks"))
|
|
return false;
|
|
|
|
if (!of_property_read_bool(np, "assigned-clock-parents"))
|
|
return false;
|
|
}
|
|
|
|
if (of_property_read_bool(np, "ti,timer-dsp"))
|
|
return false;
|
|
|
|
if (of_property_read_bool(np, "ti,timer-pwm"))
|
|
return false;
|
|
|
|
return true;
|
|
}
|
|
|
|
/*
|
|
* Finds the first available usable always-on timer, and assigns it to either
|
|
* clockevent or clocksource depending if the counter_32k is available on the
|
|
* SoC or not.
|
|
*
|
|
* Some omap3 boards with unreliable oscillator must not use the counter_32k
|
|
* or dmtimer1 with 32 KiHz source. Additionally, the boards with unreliable
|
|
* oscillator should really set counter_32k as disabled, and delete dmtimer1
|
|
* ti,always-on property, but let's not count on it. For these quirky cases,
|
|
* we prefer using the always-on secure dmtimer12 with the internal 32 KiHz
|
|
* clock as the clocksource, and any available dmtimer as clockevent.
|
|
*
|
|
* For am437x, we are using am335x style dmtimer clocksource. It is unclear
|
|
* if this quirk handling is really needed, but let's change it separately
|
|
* based on testing as it might cause side effects.
|
|
*/
|
|
static void __init dmtimer_systimer_assign_alwon(void)
|
|
{
|
|
struct device_node *np;
|
|
u32 pa = 0;
|
|
bool quirk_unreliable_oscillator = false;
|
|
|
|
/* Quirk unreliable 32 KiHz oscillator with incomplete dts */
|
|
if (of_machine_is_compatible("ti,omap3-beagle-ab4")) {
|
|
quirk_unreliable_oscillator = true;
|
|
counter_32k = -ENODEV;
|
|
}
|
|
|
|
/* Quirk am437x using am335x style dmtimer clocksource */
|
|
if (of_machine_is_compatible("ti,am43"))
|
|
counter_32k = -ENODEV;
|
|
|
|
for_each_matching_node(np, dmtimer_match_table) {
|
|
struct resource res;
|
|
if (!dmtimer_is_preferred(np))
|
|
continue;
|
|
|
|
if (!of_property_read_bool(np, "ti,timer-alwon"))
|
|
continue;
|
|
|
|
if (of_address_to_resource(np, 0, &res))
|
|
continue;
|
|
|
|
pa = res.start;
|
|
|
|
/* Quirky omap3 boards must use dmtimer12 */
|
|
if (quirk_unreliable_oscillator && pa == 0x48318000)
|
|
continue;
|
|
|
|
of_node_put(np);
|
|
break;
|
|
}
|
|
|
|
/* Usually no need for dmtimer clocksource if we have counter32 */
|
|
if (counter_32k >= 0) {
|
|
clockevent = pa;
|
|
clocksource = 0;
|
|
} else {
|
|
clocksource = pa;
|
|
clockevent = DMTIMER_INST_DONT_CARE;
|
|
}
|
|
}
|
|
|
|
/* Finds the first usable dmtimer, used for the don't care case */
|
|
static u32 __init dmtimer_systimer_find_first_available(void)
|
|
{
|
|
struct device_node *np;
|
|
u32 pa = 0;
|
|
|
|
for_each_matching_node(np, dmtimer_match_table) {
|
|
struct resource res;
|
|
if (!dmtimer_is_preferred(np))
|
|
continue;
|
|
|
|
if (of_address_to_resource(np, 0, &res))
|
|
continue;
|
|
|
|
if (res.start == clocksource || res.start == clockevent)
|
|
continue;
|
|
|
|
pa = res.start;
|
|
of_node_put(np);
|
|
break;
|
|
}
|
|
|
|
return pa;
|
|
}
|
|
|
|
/* Selects the best clocksource and clockevent to use */
|
|
static void __init dmtimer_systimer_select_best(void)
|
|
{
|
|
dmtimer_systimer_check_counter32k();
|
|
dmtimer_systimer_assign_alwon();
|
|
|
|
if (clockevent == DMTIMER_INST_DONT_CARE)
|
|
clockevent = dmtimer_systimer_find_first_available();
|
|
|
|
pr_debug("%s: counter_32k: %i clocksource: %08x clockevent: %08x\n",
|
|
__func__, counter_32k, clocksource, clockevent);
|
|
}
|
|
|
|
/* Interface clocks are only available on some SoCs variants */
|
|
static int __init dmtimer_systimer_init_clock(struct dmtimer_systimer *t,
|
|
struct device_node *np,
|
|
const char *name,
|
|
unsigned long *rate)
|
|
{
|
|
struct clk *clock;
|
|
unsigned long r;
|
|
bool is_ick = false;
|
|
int error;
|
|
|
|
is_ick = !strncmp(name, "ick", 3);
|
|
|
|
clock = of_clk_get_by_name(np, name);
|
|
if ((PTR_ERR(clock) == -EINVAL) && is_ick)
|
|
return 0;
|
|
else if (IS_ERR(clock))
|
|
return PTR_ERR(clock);
|
|
|
|
error = clk_prepare_enable(clock);
|
|
if (error)
|
|
return error;
|
|
|
|
r = clk_get_rate(clock);
|
|
if (!r) {
|
|
clk_disable_unprepare(clock);
|
|
return -ENODEV;
|
|
}
|
|
|
|
if (is_ick)
|
|
t->ick = clock;
|
|
else
|
|
t->fck = clock;
|
|
|
|
*rate = r;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __init dmtimer_systimer_setup(struct device_node *np,
|
|
struct dmtimer_systimer *t)
|
|
{
|
|
unsigned long rate;
|
|
u8 regbase;
|
|
int error;
|
|
|
|
if (!of_device_is_compatible(np->parent, "ti,sysc"))
|
|
return -EINVAL;
|
|
|
|
t->base = of_iomap(np, 0);
|
|
if (!t->base)
|
|
return -ENXIO;
|
|
|
|
/*
|
|
* Enable optional assigned-clock-parents configured at the timer
|
|
* node level. For regular device drivers, this is done automatically
|
|
* by bus related code such as platform_drv_probe().
|
|
*/
|
|
error = of_clk_set_defaults(np, false);
|
|
if (error < 0)
|
|
pr_err("%s: clock source init failed: %i\n", __func__, error);
|
|
|
|
/* For ti-sysc, we have timer clocks at the parent module level */
|
|
error = dmtimer_systimer_init_clock(t, np->parent, "fck", &rate);
|
|
if (error)
|
|
goto err_unmap;
|
|
|
|
t->rate = rate;
|
|
|
|
error = dmtimer_systimer_init_clock(t, np->parent, "ick", &rate);
|
|
if (error)
|
|
goto err_unmap;
|
|
|
|
if (dmtimer_systimer_revision1(t)) {
|
|
t->irq_stat = OMAP_TIMER_V1_STAT_OFFSET;
|
|
t->irq_ena = OMAP_TIMER_V1_INT_EN_OFFSET;
|
|
t->pend = _OMAP_TIMER_WRITE_PEND_OFFSET;
|
|
regbase = 0;
|
|
} else {
|
|
t->irq_stat = OMAP_TIMER_V2_IRQSTATUS;
|
|
t->irq_ena = OMAP_TIMER_V2_IRQENABLE_SET;
|
|
regbase = OMAP_TIMER_V2_FUNC_OFFSET;
|
|
t->pend = regbase + _OMAP_TIMER_WRITE_PEND_OFFSET;
|
|
}
|
|
|
|
t->sysc = OMAP_TIMER_OCP_CFG_OFFSET;
|
|
t->load = regbase + _OMAP_TIMER_LOAD_OFFSET;
|
|
t->counter = regbase + _OMAP_TIMER_COUNTER_OFFSET;
|
|
t->ctrl = regbase + _OMAP_TIMER_CTRL_OFFSET;
|
|
t->wakeup = regbase + _OMAP_TIMER_WAKEUP_EN_OFFSET;
|
|
t->ifctrl = regbase + _OMAP_TIMER_IF_CTRL_OFFSET;
|
|
|
|
dmtimer_systimer_reset(t);
|
|
dmtimer_systimer_enable(t);
|
|
pr_debug("dmtimer rev %08x sysc %08x\n", readl_relaxed(t->base),
|
|
readl_relaxed(t->base + t->sysc));
|
|
|
|
return 0;
|
|
|
|
err_unmap:
|
|
iounmap(t->base);
|
|
|
|
return error;
|
|
}
|
|
|
|
/* Clockevent */
|
|
static struct dmtimer_clockevent *
|
|
to_dmtimer_clockevent(struct clock_event_device *clockevent)
|
|
{
|
|
return container_of(clockevent, struct dmtimer_clockevent, dev);
|
|
}
|
|
|
|
static irqreturn_t dmtimer_clockevent_interrupt(int irq, void *data)
|
|
{
|
|
struct dmtimer_clockevent *clkevt = data;
|
|
struct dmtimer_systimer *t = &clkevt->t;
|
|
|
|
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->irq_stat);
|
|
clkevt->dev.event_handler(&clkevt->dev);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int dmtimer_set_next_event(unsigned long cycles,
|
|
struct clock_event_device *evt)
|
|
{
|
|
struct dmtimer_clockevent *clkevt = to_dmtimer_clockevent(evt);
|
|
struct dmtimer_systimer *t = &clkevt->t;
|
|
void __iomem *pend = t->base + t->pend;
|
|
|
|
while (readl_relaxed(pend) & WP_TCRR)
|
|
cpu_relax();
|
|
writel_relaxed(0xffffffff - cycles, t->base + t->counter);
|
|
|
|
while (readl_relaxed(pend) & WP_TCLR)
|
|
cpu_relax();
|
|
writel_relaxed(OMAP_TIMER_CTRL_ST, t->base + t->ctrl);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dmtimer_clockevent_shutdown(struct clock_event_device *evt)
|
|
{
|
|
struct dmtimer_clockevent *clkevt = to_dmtimer_clockevent(evt);
|
|
struct dmtimer_systimer *t = &clkevt->t;
|
|
void __iomem *ctrl = t->base + t->ctrl;
|
|
u32 l;
|
|
|
|
l = readl_relaxed(ctrl);
|
|
if (l & OMAP_TIMER_CTRL_ST) {
|
|
l &= ~BIT(0);
|
|
writel_relaxed(l, ctrl);
|
|
/* Flush posted write */
|
|
l = readl_relaxed(ctrl);
|
|
/* Wait for functional clock period x 3.5 */
|
|
udelay(3500000 / t->rate + 1);
|
|
}
|
|
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->irq_stat);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dmtimer_set_periodic(struct clock_event_device *evt)
|
|
{
|
|
struct dmtimer_clockevent *clkevt = to_dmtimer_clockevent(evt);
|
|
struct dmtimer_systimer *t = &clkevt->t;
|
|
void __iomem *pend = t->base + t->pend;
|
|
|
|
dmtimer_clockevent_shutdown(evt);
|
|
|
|
/* Looks like we need to first set the load value separately */
|
|
while (readl_relaxed(pend) & WP_TLDR)
|
|
cpu_relax();
|
|
writel_relaxed(clkevt->period, t->base + t->load);
|
|
|
|
while (readl_relaxed(pend) & WP_TCRR)
|
|
cpu_relax();
|
|
writel_relaxed(clkevt->period, t->base + t->counter);
|
|
|
|
while (readl_relaxed(pend) & WP_TCLR)
|
|
cpu_relax();
|
|
writel_relaxed(OMAP_TIMER_CTRL_AR | OMAP_TIMER_CTRL_ST,
|
|
t->base + t->ctrl);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void omap_clockevent_idle(struct clock_event_device *evt)
|
|
{
|
|
struct dmtimer_clockevent *clkevt = to_dmtimer_clockevent(evt);
|
|
struct dmtimer_systimer *t = &clkevt->t;
|
|
|
|
dmtimer_systimer_disable(t);
|
|
clk_disable(t->fck);
|
|
}
|
|
|
|
static void omap_clockevent_unidle(struct clock_event_device *evt)
|
|
{
|
|
struct dmtimer_clockevent *clkevt = to_dmtimer_clockevent(evt);
|
|
struct dmtimer_systimer *t = &clkevt->t;
|
|
int error;
|
|
|
|
error = clk_enable(t->fck);
|
|
if (error)
|
|
pr_err("could not enable timer fck on resume: %i\n", error);
|
|
|
|
dmtimer_systimer_enable(t);
|
|
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->irq_ena);
|
|
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->wakeup);
|
|
}
|
|
|
|
static int __init dmtimer_clkevt_init_common(struct dmtimer_clockevent *clkevt,
|
|
struct device_node *np,
|
|
unsigned int features,
|
|
const struct cpumask *cpumask,
|
|
const char *name,
|
|
int rating)
|
|
{
|
|
struct clock_event_device *dev;
|
|
struct dmtimer_systimer *t;
|
|
int error;
|
|
|
|
t = &clkevt->t;
|
|
dev = &clkevt->dev;
|
|
|
|
/*
|
|
* We mostly use cpuidle_coupled with ARM local timers for runtime,
|
|
* so there's probably no use for CLOCK_EVT_FEAT_DYNIRQ here.
|
|
*/
|
|
dev->features = features;
|
|
dev->rating = rating;
|
|
dev->set_next_event = dmtimer_set_next_event;
|
|
dev->set_state_shutdown = dmtimer_clockevent_shutdown;
|
|
dev->set_state_periodic = dmtimer_set_periodic;
|
|
dev->set_state_oneshot = dmtimer_clockevent_shutdown;
|
|
dev->set_state_oneshot_stopped = dmtimer_clockevent_shutdown;
|
|
dev->tick_resume = dmtimer_clockevent_shutdown;
|
|
dev->cpumask = cpumask;
|
|
|
|
dev->irq = irq_of_parse_and_map(np, 0);
|
|
if (!dev->irq)
|
|
return -ENXIO;
|
|
|
|
error = dmtimer_systimer_setup(np, &clkevt->t);
|
|
if (error)
|
|
return error;
|
|
|
|
clkevt->period = 0xffffffff - DIV_ROUND_CLOSEST(t->rate, HZ);
|
|
|
|
/*
|
|
* For clock-event timers we never read the timer counter and
|
|
* so we are not impacted by errata i103 and i767. Therefore,
|
|
* we can safely ignore this errata for clock-event timers.
|
|
*/
|
|
writel_relaxed(OMAP_TIMER_CTRL_POSTED, t->base + t->ifctrl);
|
|
|
|
error = request_irq(dev->irq, dmtimer_clockevent_interrupt,
|
|
IRQF_TIMER, name, clkevt);
|
|
if (error)
|
|
goto err_out_unmap;
|
|
|
|
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->irq_ena);
|
|
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->wakeup);
|
|
|
|
pr_info("TI gptimer %s: %s%lu Hz at %pOF\n",
|
|
name, of_property_read_bool(np, "ti,timer-alwon") ?
|
|
"always-on " : "", t->rate, np->parent);
|
|
|
|
return 0;
|
|
|
|
err_out_unmap:
|
|
iounmap(t->base);
|
|
|
|
return error;
|
|
}
|
|
|
|
static int __init dmtimer_clockevent_init(struct device_node *np)
|
|
{
|
|
struct dmtimer_clockevent *clkevt;
|
|
int error;
|
|
|
|
clkevt = kzalloc(sizeof(*clkevt), GFP_KERNEL);
|
|
if (!clkevt)
|
|
return -ENOMEM;
|
|
|
|
error = dmtimer_clkevt_init_common(clkevt, np,
|
|
CLOCK_EVT_FEAT_PERIODIC |
|
|
CLOCK_EVT_FEAT_ONESHOT,
|
|
cpu_possible_mask, "clockevent",
|
|
300);
|
|
if (error)
|
|
goto err_out_free;
|
|
|
|
clockevents_config_and_register(&clkevt->dev, clkevt->t.rate,
|
|
3, /* Timer internal resync latency */
|
|
0xffffffff);
|
|
|
|
if (of_machine_is_compatible("ti,am33xx") ||
|
|
of_machine_is_compatible("ti,am43")) {
|
|
clkevt->dev.suspend = omap_clockevent_idle;
|
|
clkevt->dev.resume = omap_clockevent_unidle;
|
|
}
|
|
|
|
return 0;
|
|
|
|
err_out_free:
|
|
kfree(clkevt);
|
|
|
|
return error;
|
|
}
|
|
|
|
/* Dmtimer as percpu timer. See dra7 ARM architected timer wrap erratum i940 */
|
|
static DEFINE_PER_CPU(struct dmtimer_clockevent, dmtimer_percpu_timer);
|
|
|
|
static int __init dmtimer_percpu_timer_init(struct device_node *np, int cpu)
|
|
{
|
|
struct dmtimer_clockevent *clkevt;
|
|
int error;
|
|
|
|
if (!cpu_possible(cpu))
|
|
return -EINVAL;
|
|
|
|
if (!of_property_read_bool(np->parent, "ti,no-reset-on-init") ||
|
|
!of_property_read_bool(np->parent, "ti,no-idle"))
|
|
pr_warn("Incomplete dtb for percpu dmtimer %pOF\n", np->parent);
|
|
|
|
clkevt = per_cpu_ptr(&dmtimer_percpu_timer, cpu);
|
|
|
|
error = dmtimer_clkevt_init_common(clkevt, np, CLOCK_EVT_FEAT_ONESHOT,
|
|
cpumask_of(cpu), "percpu-dmtimer",
|
|
500);
|
|
if (error)
|
|
return error;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* See TRM for timer internal resynch latency */
|
|
static int omap_dmtimer_starting_cpu(unsigned int cpu)
|
|
{
|
|
struct dmtimer_clockevent *clkevt = per_cpu_ptr(&dmtimer_percpu_timer, cpu);
|
|
struct clock_event_device *dev = &clkevt->dev;
|
|
struct dmtimer_systimer *t = &clkevt->t;
|
|
|
|
clockevents_config_and_register(dev, t->rate, 3, ULONG_MAX);
|
|
irq_force_affinity(dev->irq, cpumask_of(cpu));
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __init dmtimer_percpu_timer_startup(void)
|
|
{
|
|
struct dmtimer_clockevent *clkevt = per_cpu_ptr(&dmtimer_percpu_timer, 0);
|
|
struct dmtimer_systimer *t = &clkevt->t;
|
|
|
|
if (t->sysc) {
|
|
cpuhp_setup_state(CPUHP_AP_TI_GP_TIMER_STARTING,
|
|
"clockevents/omap/gptimer:starting",
|
|
omap_dmtimer_starting_cpu, NULL);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
subsys_initcall(dmtimer_percpu_timer_startup);
|
|
|
|
static int __init dmtimer_percpu_quirk_init(struct device_node *np, u32 pa)
|
|
{
|
|
struct device_node *arm_timer;
|
|
|
|
arm_timer = of_find_compatible_node(NULL, NULL, "arm,armv7-timer");
|
|
if (of_device_is_available(arm_timer)) {
|
|
pr_warn_once("ARM architected timer wrap issue i940 detected\n");
|
|
return 0;
|
|
}
|
|
|
|
if (pa == 0x4882c000) /* dra7 dmtimer15 */
|
|
return dmtimer_percpu_timer_init(np, 0);
|
|
else if (pa == 0x4882e000) /* dra7 dmtimer16 */
|
|
return dmtimer_percpu_timer_init(np, 1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Clocksource */
|
|
static struct dmtimer_clocksource *
|
|
to_dmtimer_clocksource(struct clocksource *cs)
|
|
{
|
|
return container_of(cs, struct dmtimer_clocksource, dev);
|
|
}
|
|
|
|
static u64 dmtimer_clocksource_read_cycles(struct clocksource *cs)
|
|
{
|
|
struct dmtimer_clocksource *clksrc = to_dmtimer_clocksource(cs);
|
|
struct dmtimer_systimer *t = &clksrc->t;
|
|
|
|
return (u64)readl_relaxed(t->base + t->counter);
|
|
}
|
|
|
|
static void __iomem *dmtimer_sched_clock_counter;
|
|
|
|
static u64 notrace dmtimer_read_sched_clock(void)
|
|
{
|
|
return readl_relaxed(dmtimer_sched_clock_counter);
|
|
}
|
|
|
|
static void dmtimer_clocksource_suspend(struct clocksource *cs)
|
|
{
|
|
struct dmtimer_clocksource *clksrc = to_dmtimer_clocksource(cs);
|
|
struct dmtimer_systimer *t = &clksrc->t;
|
|
|
|
clksrc->loadval = readl_relaxed(t->base + t->counter);
|
|
dmtimer_systimer_disable(t);
|
|
clk_disable(t->fck);
|
|
}
|
|
|
|
static void dmtimer_clocksource_resume(struct clocksource *cs)
|
|
{
|
|
struct dmtimer_clocksource *clksrc = to_dmtimer_clocksource(cs);
|
|
struct dmtimer_systimer *t = &clksrc->t;
|
|
int error;
|
|
|
|
error = clk_enable(t->fck);
|
|
if (error)
|
|
pr_err("could not enable timer fck on resume: %i\n", error);
|
|
|
|
dmtimer_systimer_enable(t);
|
|
writel_relaxed(clksrc->loadval, t->base + t->counter);
|
|
writel_relaxed(OMAP_TIMER_CTRL_ST | OMAP_TIMER_CTRL_AR,
|
|
t->base + t->ctrl);
|
|
}
|
|
|
|
static int __init dmtimer_clocksource_init(struct device_node *np)
|
|
{
|
|
struct dmtimer_clocksource *clksrc;
|
|
struct dmtimer_systimer *t;
|
|
struct clocksource *dev;
|
|
int error;
|
|
|
|
clksrc = kzalloc(sizeof(*clksrc), GFP_KERNEL);
|
|
if (!clksrc)
|
|
return -ENOMEM;
|
|
|
|
dev = &clksrc->dev;
|
|
t = &clksrc->t;
|
|
|
|
error = dmtimer_systimer_setup(np, t);
|
|
if (error)
|
|
goto err_out_free;
|
|
|
|
dev->name = "dmtimer";
|
|
dev->rating = 300;
|
|
dev->read = dmtimer_clocksource_read_cycles;
|
|
dev->mask = CLOCKSOURCE_MASK(32);
|
|
dev->flags = CLOCK_SOURCE_IS_CONTINUOUS;
|
|
|
|
/* Unlike for clockevent, legacy code sets suspend only for am4 */
|
|
if (of_machine_is_compatible("ti,am43")) {
|
|
dev->suspend = dmtimer_clocksource_suspend;
|
|
dev->resume = dmtimer_clocksource_resume;
|
|
}
|
|
|
|
writel_relaxed(0, t->base + t->counter);
|
|
writel_relaxed(OMAP_TIMER_CTRL_ST | OMAP_TIMER_CTRL_AR,
|
|
t->base + t->ctrl);
|
|
|
|
pr_info("TI gptimer clocksource: %s%pOF\n",
|
|
of_property_read_bool(np, "ti,timer-alwon") ?
|
|
"always-on " : "", np->parent);
|
|
|
|
if (!dmtimer_sched_clock_counter) {
|
|
dmtimer_sched_clock_counter = t->base + t->counter;
|
|
sched_clock_register(dmtimer_read_sched_clock, 32, t->rate);
|
|
}
|
|
|
|
if (clocksource_register_hz(dev, t->rate))
|
|
pr_err("Could not register clocksource %pOF\n", np);
|
|
|
|
return 0;
|
|
|
|
err_out_free:
|
|
kfree(clksrc);
|
|
|
|
return -ENODEV;
|
|
}
|
|
|
|
/*
|
|
* To detect between a clocksource and clockevent, we assume the device tree
|
|
* has no interrupts configured for a clocksource timer.
|
|
*/
|
|
static int __init dmtimer_systimer_init(struct device_node *np)
|
|
{
|
|
struct resource res;
|
|
u32 pa;
|
|
|
|
/* One time init for the preferred timer configuration */
|
|
if (!clocksource && !clockevent)
|
|
dmtimer_systimer_select_best();
|
|
|
|
if (!clocksource && !clockevent) {
|
|
pr_err("%s: unable to detect system timers, update dtb?\n",
|
|
__func__);
|
|
|
|
return -EINVAL;
|
|
}
|
|
|
|
|
|
of_address_to_resource(np, 0, &res);
|
|
pa = (u32)res.start;
|
|
if (!pa)
|
|
return -EINVAL;
|
|
|
|
if (counter_32k <= 0 && clocksource == pa)
|
|
return dmtimer_clocksource_init(np);
|
|
|
|
if (clockevent == pa)
|
|
return dmtimer_clockevent_init(np);
|
|
|
|
if (of_machine_is_compatible("ti,dra7"))
|
|
return dmtimer_percpu_quirk_init(np, pa);
|
|
|
|
return 0;
|
|
}
|
|
|
|
TIMER_OF_DECLARE(systimer_omap2, "ti,omap2420-timer", dmtimer_systimer_init);
|
|
TIMER_OF_DECLARE(systimer_omap3, "ti,omap3430-timer", dmtimer_systimer_init);
|
|
TIMER_OF_DECLARE(systimer_omap4, "ti,omap4430-timer", dmtimer_systimer_init);
|
|
TIMER_OF_DECLARE(systimer_omap5, "ti,omap5430-timer", dmtimer_systimer_init);
|
|
TIMER_OF_DECLARE(systimer_am33x, "ti,am335x-timer", dmtimer_systimer_init);
|
|
TIMER_OF_DECLARE(systimer_am3ms, "ti,am335x-timer-1ms", dmtimer_systimer_init);
|
|
TIMER_OF_DECLARE(systimer_dm814, "ti,dm814-timer", dmtimer_systimer_init);
|
|
TIMER_OF_DECLARE(systimer_dm816, "ti,dm816-timer", dmtimer_systimer_init);
|