Commit Graph

5 Commits

Author SHA1 Message Date
NeilBrown
6712ecf8f6 Drop 'size' argument from bio_endio and bi_end_io
As bi_end_io is only called once when the reqeust is complete,
the 'size' argument is now redundant.  Remove it.

Now there is no need for bio_endio to subtract the size completed
from bi_size.  So don't do that either.

While we are at it, change bi_end_io to return void.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10 09:25:57 +02:00
Jens Axboe
165125e1e4 [BLOCK] Get rid of request_queue_t typedef
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-07-24 09:28:11 +02:00
Vasily Tarasov
f772b3d9ca block: blk_max_pfn is somtimes wrong
There is a small problem in handling page bounce.

At the moment blk_max_pfn equals max_pfn, which is in fact not maximum
possible _number_ of a page frame, but the _amount_ of page frames.  For
example for the 32bit x86 node with 4Gb RAM, max_pfn = 0x100000, but not
0xFFFF.

request_queue structure has a member q->bounce_pfn and queue needs bounce
pages for the pages _above_ this limit.  This routine is handled by
blk_queue_bounce(), where the following check is produced:

	if (q->bounce_pfn >= blk_max_pfn)
		return;

Assume, that a driver has set q->bounce_pfn to 0xFFFF, but blk_max_pfn
equals 0x10000.  In such situation the check above fails and for each bio
we always fall down for iterating over pages tied to the bio.

I want to notice, that for quite a big range of device drivers (ide, md,
...) such problem doesn't happen because they use BLK_BOUNCE_ANY for
bounce_pfn.  BLK_BOUNCE_ANY is defined as blk_max_pfn << PAGE_SHIFT, and
then the check above doesn't fail.  But for other drivers, which obtain
reuired value from drivers, it fails.  For example sata_nv uses
ATA_DMA_MASK or dev->dma_mask.

I propose to use (max_pfn - 1) for blk_max_pfn.  And the same for
blk_max_low_pfn.  The patch also cleanses some checks related with
bounce_pfn.

Signed-off-by: Vasily Tarasov <vtaras@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-03-27 08:52:47 +02:00
Jens Axboe
c43a5082a6 [PATCH] blktrace: only add a bounce trace when we really bounce
Currently we issue a bounce trace when __blk_queue_bounce() is called,
but that merely means that the device has a lower dma mask than the
higher pages in the system. The bio itself may still be lower pages. So
move the bounce trace into __blk_queue_bounce(), when we know there will
actually be page bouncing.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2007-01-12 10:46:49 -08:00
David Howells
831058dec3 [PATCH] BLOCK: Separate the bounce buffering code from the highmem code [try #6]
Move the bounce buffer code from mm/highmem.c to mm/bounce.c so that it can be
more easily disabled when the block layer is disabled.

!!!NOTE!!! There may be a bug in this code: Should init_emergency_pool() be
	   contingent on CONFIG_HIGHMEM?

Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2006-09-30 20:32:11 +02:00