This define isn't used anywhere in the kernel tree -- nuke it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
The implementation for memory copy functions on ARM had a (disabled)
provision for aligning the source pointer before loading registers with
data. Turns out that aligning the _destination_ pointer is much more
useful, as the read side is already sufficiently helped with the use of
preload.
So this changes the definition of the CALGN() macro to target the
destination pointer instead, and turns it on for Feroceon processors
where the gain is very noticeable.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This adds the definition for the third USB port control register UP3OCR. It is
used on the EZX GSM mobile phones.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Macros like Fld() or FShft used in regs-lcd.h are defined in bitfield.h, but
the latter is not included.
Also fix one whitespace issue while being there.
Signed-off-by: Antonio Ospite <ao2@openezx.org>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The AT91 NAND driver needs just a few tiny modifications to work on
AVR32 as well. Rename it atmel_nand to reflect this.
Also move the ECC register definitions into drivers/mtd/nand since they
are only useful to the atmel_nand driver, and get rid of the useless
filename at the top of each file.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The power manager and core clock registers aren't present in PXA3
CPUs. Move them out of pxa-regs.h into pxa2xx-regs.h, and include
pxa2xx-regs.h where necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds support for the USB High Speed Device Port on the AT91SAM9RL
system on chip. The AT91SAM9RL uses the same UDPHS IP as the AVR32 and
the AT91CAP9 (atmel_usba_udc driver).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is patch 2 of 2 adding support for the USB High Speed Device Port
on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP
as the AVR32 and the AT91SAM9RL.
This patch declares the UDPHS ressources in the at91cap9 (cpu and
adk board) files, wires up the atmel_usba_udc driver to them,
and activates the driver in the defconfig.
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is patch 1 of 2 adding support for the USB High Speed Device Port
on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP
as the AVR32 and the AT91SAM9RL.
This patch makes the generic AT91 adaptations, mainly dealing with
the addition of the UDPHS UTMI clock.
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for three AT91-based boards available from Calao Systems:
USB_A9260, USB_A9263 and QIL_A9260.
Signed-off-by: Grégory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current __raw_write_can_lock macro tests whether the lock can be
locked by checking if it is equal to 0x80000000, whereas the lock
should be lockable if its value is 0 i.e. unlocked state is
represented by 0. Hence the macro should test the value of lock
against 0 and not 0x80000000.
Signed-off-by: Surinder Pal Singh <srplsnh@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PSKTSEL can be routed to GPIO pin 104. This configuration is used by
HP iPAQ hx4700.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some additional alternate gpio definitions relating
to FFUART and USB on the pxa27x. These are used on
the xbow imote2 platform.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Follow suit from kprobe implementations on other archs and make kretprobe_trampoline non-static. Ftrace implmentation (more specifically, kernel/trace/trace.c) requires access to it (see-> http://kerneltrap.org/mailarchive/linux-kernel/2008/5/27/1955234).
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
AT91 has one include loop in its header files:
include/asm-arm/io.h <- include/asm-arm/arch-at91/io.h <-
include/asm-arm/io.h
Circular include dependencies are dangerous since they can result in
inconsistent definitions being provided to other code, especially if
'#ifndef' constructs are used.
Solve this by removing the offending includes. Built tested using my
AT91 configuration.
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's not very critical because __REG2 isn't used in assembler code
currently.
Additionally some white space noise is fixed.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
atags.c was the only user of KEXEC_BOOT_PARAMS_SIZE and kexec.h
was only included to get that definition.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Acked-by: Uli Luckas <u.luckas@road.de>
OMAP has two include loops in its header files:
asm-arm/hardware.h <- asm-arm/arch-omap/io.h <-
asm-arm/arch-omap/hardware.h <- asm-arm/hardware.h
asm-arm/arch-omap/board-palmte.h <-
asm-arm/arch-omap/hardware.h <- asm-arm/hardware.h <-
asm-arm/arch-omap/gpio.h <- asm-arm/arch-omap/board-palmte.h
Circular include dependencies are dangerous since they can result in
inconsistent definitions being provided to other code, especially if
'#ifndef' constructs are used.
Solve these by removing the offending includes, and add additional
includes where necessary.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For the simple read_cpuid() macro case the variable processor_id has
no definition on use of the macro. Add an extern for it. Move all the
processor ID macros into the #ifndef __ASSEMBLEY__ block.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The non-MMU case also needs the type definition of pgtable_t.
So move it out of a CONFIG_MMU conditional section.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/plat-omap/clock.c:397: warning: "struct cpufreq_frequency_table" declared inside parameter list
arch/arm/plat-omap/clock.c:397: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/plat-omap/clock.c: In function `clk_init_cpufreq_table':
arch/arm/plat-omap/clock.c:402: error: structure has no member named `clk_init_cpufreq_table'
arch/arm/plat-omap/clock.c:403: error: structure has no member named `clk_init_cpufreq_table'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that all drivers using it are gone, remove the old ARM RTC library.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
collie.h:
* add some meaningfull names to some gpios
collie.c:
* initialize cpu registers correctly
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PXA25x and PXA27x USB device controller register definitions are
different. Currently, they live side by side in pxa-regs.h, but only
one set is available depending on the setting of PXA25x or PXA27x.
This means that if we build to support both PXA25x and PXA27x, the
PXA27x definitions are unavailable, even to PXA27x specific code.
Remove these definitions from pxa-regs.h, and place them in separate
files. Include these files where appropriate.
Note: according to the dependencies in drivers/usb/gadget/Kconfig,
we do not support the UDC on PXA27x nor PXA3xx CPUs, so remove the
platform devices from pxa27x.c and pxa3xx.c.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Parenthesis fix in include/asm-arm/arch-omap/control.h
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irqs.h:
* rename IRQ_LOCOMO_SPI_OVRN to IRQ_LOCOMO_SPI_REND
locomo.h:
* add some definition for locomo spi controller
* correct some errors
locomo.c:
* correct some errors
* add set_type for locomo gpio irq chip
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dyntick is superseded by the clocksource/clockevent infrastructure,
using the NO_HZ configuration option. No one implements dyntick on
ARM anymore, so it's pointless keeping it around. Remove dyntick
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the omap2_set_globals_{242x,243x,343x}() functions. These
functions are called early upon boot in the map_io() functions in the
board-specific init files.
This patch was accidentally left out of the earlier series.
This fixes omap2 booting as noted by Kyungmin Park <kmpark@infradead.org>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Related to d3930614e6.
RCSR is only present on PXA2xx CPUs, not on PXA3xx CPUs. Therefore,
we should not be unconditionally writing to RCSR from generic code.
Since we now clear the RCSR status from the SoC specific PXA PM code
and before reset in the arch_reset() function, the duplication in
the corgi, poodle, spitz and tosa code can be removed.
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Each time a pxa type cpu went in suspend, a portion of
kmalloc memory was corrupted.
The issue was an incorrect length allocation introduced by
the commit 711be5ccfe for
the save registers array (=> overflow).
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This modifies <asm-arm/types.h> to use the <asm-generic/int-*.h>
generic include files.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Trying to compile a kerel for ARCH_CO285 fails with the following error:
<-- snip -->
...
CC arch/arm/mach-footbridge/dc21285.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:
In function 'dc21285_base_address':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: 'PCICFG0_BASE' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:57: error: 'PCICFG1_BASE' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:
In function 'dc21285_scan_bus':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:286: error: implicit declaration of function 'pci_scan_bus'
...
make[2]: *** [arch/arm/mach-footbridge/dc21285.o] Error 1
<-- snip -->
This does not seem to be a recent breakage.
The ARCH_CO285 support is old - kernel 2.2.0 contains first traces of
it, an it seems to have been pretty complete in later 2.2 kernels.
Since it seems to be completely dead code now this patch therefore
removes it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename div64_64 to div64_u64 to make it consistent with the other divide
functions, so it clearly includes the type of the divide. Move its definition
to math64.h as currently no architecture overrides the generic implementation.
They can still override it of course, but the duplicated declarations are
avoided.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reasons:
1. straight forward: the name "LCD_COLOR_DSTN_16BPP" is much better
than "LCCR0_Pas | LCCR0_Color | LCCR0_Dual"
2. by defining LCD connection types as constants, it allows only
valid possibilities
3. by removing the dependency of register bits definitions, those
can be later moved into the body of pxafb.c, instead of having
a regs-lcd.h around
Currently, only lubbock, mainstone, zylonite and littleton have been
modified to support these types (see coming patches after this).
Other platforms are encouraged to change their way describing the
LCD controller connections.
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is part of the effort moving peripheral registers outside of pxa-regs.h,
and using ioremap() make it possible the same IP can be re-used on different
processors with different registers space
As a result, the fixed mapping in pxa_map_io() is removed.
The regs-lcd.h can actually moved to where closer to pxafb.c but some of its
bit definitions are directly used by various platform code, though this is not
a good style.
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unaligned access is ok for the following arches:
cris, m68k, mn10300, powerpc, s390, x86
Arches that use the memmove implementation for native endian, and
the byteshifting for the opposite endianness.
h8300, m32r, xtensa
Packed struct for native endian, byteshifting for other endian:
alpha, blackfin, ia64, parisc, sparc, sparc64, mips, sh
m86knommu is generic_be for Coldfire, otherwise unaligned access is ok.
frv, arm chooses endianness based on compiler settings, uses the byteshifting
versions. Remove the unaligned trap handler from frv as it is now unused.
v850 is le, uses the byteshifting versions for both be and le.
Remove the now unused asm-generic implementation.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements a set of Feroceon-specific
{copy,clear}_user_page() routines that perform more optimally than
the generic implementations. This also deals with write-allocate
caches (Feroceon can run L1 D in WA mode) which otherwise prevents
Linux from booting.
[nico: optimized the code even further]
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The ioremap() optimization used for internal register didn't cope
with the fact that paddr + size can wrap to zero if the area extends
to the end of the physical address space.
Issue isolated by Sylver Bruneau <sylver.bruneau@googlemail.com>.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
s390 for one, cannot implement VM_MIXEDMAP with pfn_valid, due to their memory
model (which is more dynamic than most). Instead, they had proposed to
implement it with an additional path through vm_normal_page(), using a bit in
the pte to determine whether or not the page should be refcounted:
vm_normal_page()
{
...
if (unlikely(vma->vm_flags & (VM_PFNMAP|VM_MIXEDMAP))) {
if (vma->vm_flags & VM_MIXEDMAP) {
#ifdef s390
if (!mixedmap_refcount_pte(pte))
return NULL;
#else
if (!pfn_valid(pfn))
return NULL;
#endif
goto out;
}
...
}
This is fine, however if we are allowed to use a bit in the pte to determine
refcountedness, we can use that to _completely_ replace all the vma based
schemes. So instead of adding more cases to the already complex vma-based
scheme, we can have a clearly seperate and simple pte-based scheme (and get
slightly better code generation in the process):
vm_normal_page()
{
#ifdef s390
if (!mixedmap_refcount_pte(pte))
return NULL;
return pte_page(pte);
#else
...
#endif
}
And finally, we may rather make this concept usable by any architecture rather
than making it s390 only, so implement a new type of pte state for this.
Unfortunately the old vma based code must stay, because some architectures may
not be able to spare pte bits. This makes vm_normal_page a little bit more
ugly than we would like, but the 2 cases are clearly seperate.
So introduce a pte_special pte state, and use it in mm/memory.c. It is
currently a noop for all architectures, so this doesn't actually result in any
compiled code changes to mm/memory.o.
BTW:
I haven't put vm_normal_page() into arch code as-per an earlier suggestion.
The reason is that, regardless of where vm_normal_page is actually
implemented, the *abstraction* is still exactly the same. Also, while it
depends on whether the architecture has pte_special or not, that is the
only two possible cases, and it really isn't an arch specific function --
the role of the arch code should be to provide primitive functions and
accessors with which to build the core code; pte_special does that. We do
not want architectures to know or care about vm_normal_page itself, and
we definitely don't want them being able to invent something new there
out of sight of mm/ code. If we made vm_normal_page an arch function, then
we have to make vm_insert_mixed (next patch) an arch function too. So I
don't think moving it to arch code fundamentally improves any abstractions,
while it does practically make the code more difficult to follow, for both
mm and arch developers, and easier to misuse.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Carsten Otte <cotte@de.ibm.com>
Cc: Jared Hulbert <jaredeh@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Add struct ide_io_ports and use it instead of `unsigned long io_ports[]`
in ide_hwif_t.
* Rename io_ports[] in hw_regs_t to io_ports_array[].
* Use un-named union for 'unsigned long io_ports_array[]' and 'struct
ide_io_ports io_ports' in hw_regs_t.
* Remove IDE_*_OFFSET defines.
v2:
* scc_pata.c build fix from Stephen Rothwell.
v3:
* Fix ctl_adrr typo in Sparc-specific part of ns87415.c.
(Noticed by Andrew Morton)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The kernel should clean stale bits from reset status, so that
they won't confuse the bootloader.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch kills the use of IRQ_GPIO() and adds
#if NR_IRQS < (IT8152_LAST_IRQ+1) statement.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support to disable ECC checking for a given chip
when passed by the board via the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for the ECC layout to be passed via the
platform data specified by the board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If a block's ecc field is all 0xff, then ignore the ECC
correction. This is for systems where some of the blocks,
such as the initial cramfs are written without ECC and
need to be loaded on start.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is preliminary since:
1. It supports only _one_ chip select at the moment. As there is no
existing platforms available using two chip selects of the NAND
controller, it shall really not include code for supporting the
2nd chip select for now, as such code cannot be verified.
2. It resorts to the default and simpliest memory based badblock
table
3. Only limited types of nand flash are currently supported. Most
PXA3xx processors come with on-chip NAND flash dies, so there
isn't much flexibility for other types of NAND.
4. The NAND controller should be configured to detect the device's
ID, thus making it difficult to use nand_scan_ident() to assist
the detection process (though it's not impossible)
TODO: fix all the above limitations of cuz :-)
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (26 commits)
mmc: sdio_ops.c should #include "sdio_ops.h"
mmc: proper prototypes for mmc_attach_*()
mmc: make __mmc_release_bus() static
sdhci: improve no card, no reset quirk
MMC: OMAP: Do not busy wait for end of command for ever
MMC: OMAP: Start new commands from work queue instead of irq
MMC: OMAP: Lazy clock shutdown
MMC: OMAP: Move failing command abortion to workqueue
MMC: OMAP: Use tasklet instead of workqueue for cover switch notification
MMC: OMAP: Check the get_cover_state function pointer if not set
MMC: OMAP: Using setup_timer instead of init_timer
MMC: OMAP: Abort stuck commands
MMC: OMAP: General cleanup for MMC multislot support
MMC: OMAP: Power functions modified to MMC multislot support
MMC: OMAP: Fix timeout calculation for MMC multislot support
MMC: OMAP: New release dma and abort xfer functions
MMC: OMAP: Add back cover switch support
MMC: OMAP: Introduce new multislot structure and change driver to use it
MMC: OMAP: Remove cover switch handling to allow adding multislot support
MMC: OMAP: Fix the BYTEBLOCK capability removal
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/juhl/trivial: (24 commits)
DOC: A couple corrections and clarifications in USB doc.
Generate a slightly more informative error msg for bad HZ
fix typo "is" -> "if" in Makefile
ext*: spelling fix prefered -> preferred
DOCUMENTATION: Use newer DEFINE_SPINLOCK macro in docs.
KEYS: Fix the comment to match the file name in rxrpc-type.h.
RAID: remove trailing space from printk line
DMA engine: typo fixes
Remove unused MAX_NODES_SHIFT
MAINTAINERS: Clarify access to OCFS2 development mailing list.
V4L: Storage class should be before const qualifier (sn9c102)
V4L: Storage class should be before const qualifier
sonypi: Storage class should be before const qualifier
intel_menlow: Storage class should be before const qualifier
DVB: Storage class should be before const qualifier
arm: Storage class should be before const qualifier
ALSA: Storage class should be before const qualifier
acpi: Storage class should be before const qualifier
firmware_sample_driver.c: fix coding style
MAINTAINERS: Add ati_remote2 driver
...
Fixed up trivial conflicts in firmware_sample_driver.c
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Alternate function and direction setting is now handled
by the MFP config code or the generic GPIO API.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a driver for the Quick Capture Interface on the PXA270.
It is based on the original driver from Intel, but has been re-worked
multiple times since then, now it also supports the V4L2 API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds support for the generic GPIO lib to the EP93xx family. The gpio
handling code has been moved from core.c to a new file called gpio.c.
The GPIO based IRQ code has not been changed.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for two more leds:
the wlan one (found in SL-6000W and SL-6000L) and
the blutooth one (found in SL-6000W).
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that scoop gpio's are converted to generic_gpio,
tosascoop_device and tosascoop_jc_device don't have
to be exported.
Also make tosa_gpio_* static
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Set up the IRQ line for the WM9713 device on the Zylonite.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-tosa.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert set/reset_scoop_gpio to generic gpio calls.
This patch depends on the pxaficp_ir hooks patch.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let platform do some specific initialisation and cleanup
things during pxaficp_ir probing and removing. E.g. this
can be usefull to request/free gpios used by the platform
to control the transceiver.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes misprint in definition of CICR1_RGBT_CONV in include/asm-arm/arch-pxa/pxa-regs.h
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All magician devices I've encountered so far have featured the Toppoly
TD028STEB1 display, so the Samsung LTP280QV support is untested.
The power-on sequence is not correct because pxafb doesn't yet support
enabling the LCD controller in the middle of the it.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
needed for power management (audio, BT, charging, GSM, LCD, SD), GSM, flash and SD operation and audio routing.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA GPIO definitions were split from pxa-regs.h into pxa2xx-gpio.h.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements support for Gumstix-F flash, udc and mci. Fixes since the last time are:
- Steve Sakoman as maintainer
- cleanup for udc and mci setup
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Keypad registers are now fully defined within pxa27x-keypad.c, no
need to keep those definitions in pxa-regs.h
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
also update the clk definitions in pxa27x and pxa3xx.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changes include:
1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
the board capability of this pin to wakeup the system
2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
enable/disable wakeup from GPIOs and keypad GPIO
* these functions are currently kept in mfp-pxa2xx.c due to their
dependency to the MFP configuration
3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
is set on incorrect pins
So that the GPIO's wakeup capability is now decided by the following:
a) processor's capability: (only those GPIOs which have dedicated
bits within PWER/PRER/PFER can wakeup the system), this is
initialized by pxa{25x,27x}_init_mfp()
b) board design decides:
- whether the pin is designed to wakeup the system (some of
the GPIOs are configured as other functions, which is not
intended to be a wakeup source), by OR'ing the pin config
with MFP_LPM_CAN_WAKEUP
- which edge the pin is designed to wakeup the system, this
may depends on external peripherals/connections, which is
totally board specific; this is indicated by MFP_LPM_EDGE_*
c) the corresponding device's (most likely the gpio_keys.c) wakeup
attribute:
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes the code better organized and simplified a bit. The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.
This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable. The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)
The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).
"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enhanced GPIO alternate functions descriptions,
taken from Intel PXA270 Developers Manual.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Expose control of the PXA3xx 13MHz CLK_POUT pin via the clock API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the base files for the PB1176 platform support.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the base files for the PB11MPCore platform support.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch changes the IO_ADDRESS macro for the RealView platforms to
accomodate a wider range of physical addresses on PB11MPCore.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The upcoming PB11MPCore and PB1176 have different memory maps and some
of the definitions in platform.h are no longer common. This patch
moves them to the board-eb.h file and updates their usage in
realview_eb.c.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since the PB1176 has different UART base addresses, this patch moves
the definitions form platorm.h to board-eb.h. It also modifies
uncompress.h to detect the platform type at run-time.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the timer definitions from platform.h into board-eb.h
as they are different on PB11MPCore and PB1176. It also adds
timerX_va_base variables in core.c which are set by the
realview_eb_timer_init function before invoking realview_timer_init.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the patch definitions into board-eb.h and
realview_eb.c (from core.c) as they are different on the PB11MPCore
and PB1176 platforms.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This is in preparation for the RealView PB11MPCore and PB1176 patches
which have different base addresses for the GIC.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the SCU initialisation from __v6_setup to the
smp_prepare_cpus() function as it relies on platform-specific
settings. Changes to get_core_count() are mainly for allowing cleaner
code with the upcoming PB11MPCore patches.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds a prefetch abort handler similar to the data abort one
and renames the latter for consistency. Initial implementation by Paul
Brook with some renaming by Catalin Marinas.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Introduce new MMC multislot structure and change driver to use it.
Note that MMC clocking is now enabled in mmc_omap_select_slot()
and disabled in mmc_omap_release_slot().
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: ack to flags: make use of the unused bits in the 'ack' field
iop-adma: remove the workaround for missed interrupts on iop3xx
async_tx: kill ->device_dependency_added
async_tx: fix multiple dependency submission
fsldma: Split the MPC83xx event from MPC85xx and refine irq codes.
fsldma: Remove CONFIG_FSL_DMA_SELFTEST, keep fsl_dma_self_test() running always.
It is always == '((base) + 0x206)' if CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS=y
and it is not needed otherwise (arm, blackfin, parisc, ppc64, sh, sparc[64]).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a small addition of forgotten defines to regs-gpio.h include file for the Samsung S3C2410 ARM9 SoC
Signed-off-by: Davide Rizzo <davide@elpa.it>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There seems to be some problem with at-least the S3C2440 and
bus traffic during an reset. It is unlikely, but still possible
that the system will hang in such a way that the watchdog cannot
get the system out of the state it is in.
Change to making the code that calls the watchdog reset run from
cached memory so that instruction fetches have quiesced before the
watchdog fires.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the name of the S3C2412_CLKDIVN_ARMDIVN define.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add initial defines for the S3C2412's memory controller registers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Juergen Beisert <j.beisert@pengutronix.de>
This patch separates the current code into i.MX2 and i.MX3 and modifies
the Kconfig files to reflect this separation in the menus.
Things happend since last review:
- make i.MX3 compile again
- fix some structure names to be conform with all the shared/common
sources from i.MX1/i.MX2
Previous changes:
- stay conform to other Kconfig files (note from Russell King)
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Simple gpio-connected LED driver for KS8695 platforms.
(Based on old AT91 LED driver)
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
The SPI core now expects num_chipselect to be set correctly as due to added
checks on the chip being selected before an transfer is allowed. This patch
adds a num_cs field to the platform data which needs to be set correctly
before adding the SPI platform device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes is the result of the discussion with Paul Walmsley.
His ideas are included into this patch.
Remove DPLL output divider handling from DPLLs and CLKOUTX2 clocks,
and place it into specific DPLL output divider clocks (e.g., dpll3_m2_clk).
omap2_get_dpll_rate() now returns the correct DPLL rate, as represented
by the DPLL's CLKOUT output. Also add MPU and IVA2 subsystem clocks, along
with high-frequency bypass support.
Add support for DPLLs function in locked and bypass clock modes.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes 24xx to use shared clock code and new register
access.
Note that patch adds some temporary OLD_CK defines to keep patch
more readable. These temporary defines will be removed in the next
patch. Also not all clocks are changed in this patch to limit the
size.
Also, the patch fixes few incorrect clock defines in clock24xx.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes 24xx to use new register access, except for clock
framework. Clock framework register access will get updates in the
next patch.
Note that board-*.c files change GPMC (General Purpose Memory Controller)
access to use gpmc_cs_write_reg() instead of accessing the registers
directly. The code also uses gpmc_fck instead of it's parent clock
core_l3_ck for GPMC clock.
The H4 board file also adds h4_init_flash() function, which specify the
flash start and end addresses.
Also note that sleep.S removes some unused registers addresses.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds common register access for 24xx and 34xx power
and clock management in order to share code between 24xx and 34xx.
Only change USB platform init code to use new register access, other
access will be changed in later patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Misc clean-up for the mux code and remove some unnecessary
ifdefs. Patch changes debug function so it can be used on
both 24xx and 34xx.
Changes are mostly for omap2, but patch also cleans up some
omap1 and common mux code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes pin multiplexing init to allow registering
custom function. The omap_cfg_reg() func will be split into
omap processor specific functions in later patch.
This is done to make adding omap3 pin multiplexing easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OSK board to use new tps65010 gpiolib support. This
includes moving its LED support from leds-osk to gpio-leds,
giving more trigger options and a net platform code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update OMAP to use the new GPIO implementation framework. This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This deprecates old set/reset_scoop_gpio interfacein favour of
support for generic gpio interface.
It requires gpiolib, so it depends on the previous patch
(gpiolib for SA-1100).
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds gpiolib support for the SA-1100 arch:
- Move all GPIO API functions from generic.c into gpio.c
- Convert all gpio functions into gpiolib callbacks.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The allowed values for the MDIV field (Master Clock Division) in the
PMC controller differ between the AT91RM9200 and AT91SAM9/CAP9.
To remove possible confusion, change the definitions to be more explicit.
Also define the Processor Clock Division bits.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Freecom-FSG3 is a small network-attached-storage device with the
following feature set:
* Intel IXP422
* 4MB Flash (ixp4xx flash driver)
* 64MB RAM
* 4 USB 2.0 host ports (ehci and ohci drivers)
* 1 WAN (eth1) and 3 LAN (eth0) ethernet ports
* Supported by the open source ixp4xx ethernet driver
* Via VT6421 disk controller (libata and sata-via drivers)
* Internal hard disk (PATA supported, SATA not yet supported)
* External SATA port (not yet supported)
* ISL1208 RTC chip
* Winbond 83782 temp sensor and fan controller
* MiniPCI slot
The ixp4xx_defconfig is also updated to support this device (the
leds-fsg driver is to be submitted separately via the leds tree after
this initial support is merged, as it depends on header gpio defines).
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Reset controller on the SAM9/CAP9 processors will store the reason
for the last system reset.
On startup, display this information (wakeup signal, RTT alarm,
watchdog reset, user reset, etc)
Based on patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On AT91 processors that include an ECC controller, pass its base
address to the NAND driver via platform_device resources.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91CAP9 processor includes the same Static Memory Controller
(SMC) peripheral as the SAM9 processors, but replaces the SDRAM
Controller with a DDR/SDR Controller (DDRSDRC).
This patch splits the existing
include/asm-arm/arch-at91/at91sam926x_mc.h into at91sam9_sdramc.h and
at91sam9_smc.h.
It also adds an at91cap9_ddrsdr.h for the DDRSDRC controller.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently include/linux/kvm.h is not considered by make headers_install,
because Kbuild cannot handle " unifdef-$(CONFIG_FOO) += foo.h. This problem
was introduced by
commit fb56dbb31c
Author: Avi Kivity <avi@qumranet.com>
Date: Sun Dec 2 10:50:06 2007 +0200
KVM: Export include/linux/kvm.h only if $ARCH actually supports KVM
Currently, make headers_check barfs due to <asm/kvm.h>, which <linux/kvm.h>
includes, not existing. Rather than add a zillion <asm/kvm.h>s, export kvm.
only if the arch actually supports it.
Signed-off-by: Avi Kivity <avi@qumranet.com>
which makes this an 2.6.25 regression.
One way of solving the issue is to enhance Kbuild, but Avi and David conviced
me, that changing headers_install is not the way to go. This patch changes
the definition for linux/kvm.h to unifdef-y.
If unifdef-y is used for linux/kvm.h "make headers_check" will fail on all
architectures without asm/kvm.h. Therefore, this patch also provides
asm/kvm.h on all architectures.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Avi Kivity <avi@qumranet.com>
Cc: Sam Ravnborg <sam@ravnborg.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From: Juergen Beisert <j.beisert@pengutronix.de>
Clean up current header files from doxygen style comments. There are
probably more such comments left, but we start with these.
Things happend since last review:
- needless blank lines removed (note by Russell King)
- re-format comments (note by Ross Wille)
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Ross Wille <wille@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now putc writes to the first enabled internal UART. If there is none
the external UART on the a9m9750dev board is used (if enabled).
Otherwise there is no output.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
The hardware team changed some things that were taken as being common to
all ns9xxx processors up to now.
This patch addresses:
- irqs: s/IRQ_/IRQ_NS9360_/
- system module registers: some registers are still general, their
definition lives now in include/asm-arm/arch-ns9xxx/regs-sys-common.h.
The ns9360 specific ones are in .../regs-sys-ns9360.h
As a result ns9360_systemclock cannot be static inline any more as its
definition needs regs-sys-ns9360.h. This becomes a real problem when
adding support for ns9215 as this will need regs-sys-ns9215.h and
including both files will not work. For the same reason
ns9360_reset() is now non-inline and gpio functions live in their own
file.
- register mapping: s/ns9xxx_map_io/ns9360_map_io/
- timer registers: move time.c to time-ns9360.c;
s/ns9xxx_timer/ns9360_timer/
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
This patch optimizes the irq handling a bit. Now the base register is only
computed once if more than one irq is pending.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Do a global s/orion/orion5x/ of the Orion 5x-specific bits (i.e.
not the plat-orion bits.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Various Orion cleanups:
- Unify GPL license banner format across all files.
- Unify naming of .h double inclusion guard preprocessor macros.
- Unify spelling of "PCIe" (variants seen: PCIE, PCIe, PCI-EX.)
- Various typo fixes.
- Remove __init attributes from prototypes declared in headers.
- Remove trailing comments from #endif statements.
- Mark a couple of locally-used-only structs static.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Save some TLB entries by making ioremap() return pointers into the
boot-time Orion peripheral iotable mapping whenever someone tries
to ioremap any part of the Orion peripheral register space.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Move the Orion register accessor macros out of orion.h, to prevent
them from ending up in the decompressor image (Orion uncompress.h
includes orion.h.) Move them into io.h, which seems a better place
for this kind of stuff.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Include a table describing our physical address map in orion.h.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Split off Orion time handling code into plat-orion/.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Split off Orion PCIe handling code into plat-orion/.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Split off Orion IRQ handling code into plat-orion/, and add
support for multiple sets of (32) interrupts.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Make it possible to pass mbus_dram_target_info to the ehci-orion
driver via the platform data, make the ehci-orion driver program
the window registers based on this data if it is passed in, and
make the Orion platform setup code use this method instead of
programming the EHCI mbus window registers by hand.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Platforms like iq80321 and iq80331 which may be host-bus-adapters
require 'iop3xx_init_atu=y' to be specified on the kernel command line.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is a bug correction for a macro that generated wrong results.
Nobody used it in official kernel tree, my driver did.
Signed-off-by: Davide Rizzo <davide@elpa.it>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Until DSP MMU code is merged, dsp_request_mem() does not exist.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define AT91_USART0, 1, 2 so the selection of the UART for early kernel
messages works.
(See commit fa3218d859).
Replace AT91_SHDC with AT91_SHDWC to be consistent with other AT91 platforms.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The nonmmu version of pgtable.h needs to include asm-generic/pgtable.h
as well. It needs to pick up empty definitions of things like
arch_enter_lazy_cpu_mode() to compile cleanly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of build warnings and errors in mainline for H3 boards; not
all the H3 updates were correct, it seems like the OMAP1 boards are
not getting proper build testing.
Also, commit e27a93a944 introduced a
regression related to the tps65013 chip.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CONFIG_HAVE_KRETPROBES to the arch/<arch>/Kconfig file for relevant
architectures with kprobes support. This facilitates easy handling of
in-kernel modules (like samples/kprobes/kretprobe_example.c) that depend on
kretprobes being present in the kernel.
Thanks to Sam Ravnborg for helping make the patch more lean.
Per Mathieu's suggestion, added CONFIG_KRETPROBES and fixed up dependencies.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PXA3xx AC97 controller has an additional control bit GCR_CLKBPB
which must be used during cold reset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This typo causes the incorrect calculation of the IRQ numbers
in the ICIP2 registers.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch sets KEXEC_CONTROL_MEMORY_LIMIT to (-1)UL. As the value is
compared with physical addresses TASK_SIZE makes no sense. Machines
where the RAM addresses start above TASK_SIZE kexecs eats all memory
and crashes the kernel without this patch.
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Sandeen tracked an XFS on ARM corruption bug down to a function
under fs/xfs/ involving some get_unaligned() calls on u64 pointers.
As it turns out, calling ARM's get_unaligned() on a u64 pointer
pointing to the following byte sequence:
80 81 82 83 84 85 86 87
would return ffffffff83828180 (LE mode.) This turns out to be
because of implicit u8 -> int promotion in ARM's implementation of
various helpers for get_unaligned(), causing them to accidentally
return signed instead of unsigned values, which in turn caused the
subsequent casts to unsigned long long in __get_unaligned_8_[bl]e()
to sign-extend the lower words.
Fix by casting the return values of __get_unaligned_[24]_[bl]e()
to unsigned int.
Cc: Eric Sandeen <sandeen@sandeen.net>
Cc: Rabeeh Khoury <rabeeh@marvell.com>
Cc: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes a sequencing bug in spi driver pxa2xx_spi.c in which the chip select
for a transfer may be asserted before the clock polarity is set on the
interface. As a result of this bug, the clock signal may have the wrong
polarity at transfer start, so it may need to make an extra half transition
before the intended clock/data signals begin. (This probably means all
transfers are one bit out of sequence.)
This only occurs on the first transfer following a change in clock polarity
in systems using more than one more than one such polarity. The fix
assures that the clock mode is properly set before asserting chip select.
This bug was introduced in a patch merged on 2006/12/10, kernel 2.6.20.
The patch defines an additional bit in: include/asm-arm/arch-pxa/regs-ssp.h
for 2.6.25 and newer kernels but this addition must be made in:
include/asm-arm/arch-pxa/pxa-regs.h for kernels between 2.6.20 and 2.6.24,
inclusive
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch updates stale comment that pointed to nonexistent file.
Signed-off-by: Leonid Evdokimov <leon@darkk.net.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master:
[ARM] constify function pointer tables
[ARM] 4823/1: AT91 section fix
[ARM] 4824/1: pxa: clear RDH bit after any reset
[ARM] pxa: remove debugging PM: printk
* omap1-upstream:
ARM: OMAP1: Misc clean-up
ARM: OMAP1: Update defconfigs for omap1
ARM: OMAP1: Palm Tungsten E board clean-up
ARM: OMAP1: Use I2C bus registration helper for omap1
ARM: OMAP1: Remove omap_sram_idle()
ARM: OMAP1: PM fixes for OMAP1
ARM: OMAP1: Use MMC multislot structures for Siemens SX1 board
ARM: OMAP1: Make omap1 use MMC multislot structures
ARM: OMAP1: Change the comments to C style
ARM: OMAP1: Make omap1 boards to use omap_nand_platform_data
ARM: OMAP: Add helper module for board specific I2C bus registration
ARM: OMAP: Add dmtimer support for OMAP3
ARM: OMAP: Pre-3430 clean-up for dmtimer.c
ARM: OMAP: Add DMA support for chaining and 3430
ARM: OMAP: Add 24xx GPIO debounce support
ARM: OMAP: Get rid of unnecessary ifdefs in GPIO code
ARM: OMAP: Add 3430 gpio support
ARM: OMAP: Add 3430 CPU identification macros
ARM: OMAP: Request DSP memory for McBSP
* orion:
[ARM] Orion: Use the sata_mv driver for the TS-209 SATA
[ARM] Orion: Use the sata_mv driver for the Kurobox SATA
[ARM] Orion: free up kernel virtual address space
[ARM] Orion: distinguish between physical and virtual addresses
[ARM] Orion: kill orion_early_putstr()
[ARM] Orion: update defconfig
[ARM] Orion: Use the sata_mv driver for the integrated SATA controller
Use MMC multislot structures for Siemens SX1 board
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make omap1 use new MMC multislot structures. The related MMC
patches will be sent separately.
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br>
Signed-off-by: Anderson Briglia <anderson.briglia@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: David Cohen <david.cohen@indt.org.br>
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap_nand_platform data based on a patch
by Shahrom Sharif-Kashani <sshahrom@micron.com>, and makes
omap1 boards to use omap_nand_platform_data instead of
nand_platform_data used earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This helper module simplifies I2C bus registration for different OMAP
platforms by doing registration in one place only and to allow board
specific bus configuration like clock rate and number of busses configured.
Helper should cover OMAP processors from first to third generation.
This patch just adds the feature and current implementation cleanup and
board file modifications will be done in following patches.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DMA support for chaining and 3430.
Also remove old DEBUG_PRINTS as noted by Russell King.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add 24xx GPIO debounce support. Also minor formatting
clean-up.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 3430 gpio support.
It also contains a fix by Paul Walmsley <paul@pwsan.com> to use the
correct clock names for OMAP3430.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap3430 CPU identification macros.
Silicon revision check macros added by Girish S G <girishsg@ti.com>.
CPU identification macro and silicon revision check macros
cleaned up by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Girish S G <girishsg@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Background: I've implemented 1K/2K page tables for s390. These sub-page
page tables are required to properly support the s390 virtualization
instruction with KVM. The SIE instruction requires that the page tables
have 256 page table entries (pte) followed by 256 page status table entries
(pgste). The pgstes are only required if the process is using the SIE
instruction. The pgstes are updated by the hardware and by the hypervisor
for a number of reasons, one of them is dirty and reference bit tracking.
To avoid wasting memory the standard pte table allocation should return
1K/2K (31/64 bit) and 2K/4K if the process is using SIE.
Problem: Page size on s390 is 4K, page table size is 1K or 2K. That means
the s390 version for pte_alloc_one cannot return a pointer to a struct
page. Trouble is that with the CONFIG_HIGHPTE feature on x86 pte_alloc_one
cannot return a pointer to a pte either, since that would require more than
32 bit for the return value of pte_alloc_one (and the pte * would not be
accessible since its not kmapped).
Solution: The only solution I found to this dilemma is a new typedef: a
pgtable_t. For s390 pgtable_t will be a (pte *) - to be introduced with a
later patch. For everybody else it will be a (struct page *). The
additional problem with the initialization of the ptl lock and the
NR_PAGETABLE accounting is solved with a constructor pgtable_page_ctor and
a destructor pgtable_page_dtor. The page table allocation and free
functions need to call these two whenever a page table page is allocated or
freed. pmd_populate will get a pgtable_t instead of a struct page pointer.
To get the pgtable_t back from a pmd entry that has been installed with
pmd_populate a new function pmd_pgtable is added. It replaces the pmd_page
call in free_pte_range and apply_to_pte_range.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some arches (like alpha and ia64) already have a clean posix_types.h header.
This brings all the others in line by removing all references to __GLIBC__
(and some undocumented __USE_ALL).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suppress A.OUT library support if CONFIG_ARCH_SUPPORTS_AOUT is not set.
Not all architectures support the A.OUT binfmt, so the ELF binfmt should not
be permitted to go looking for A.OUT libraries to load in such a case. Not
only that, but under such conditions A.OUT core dumps are not produced either.
To make this work, this patch also does the following:
(1) Makes the existence of the contents of linux/a.out.h contingent on
CONFIG_ARCH_SUPPORTS_AOUT.
(2) Renames dump_thread() to aout_dump_thread() as it's only called by A.OUT
core dumping code.
(3) Moves aout_dump_thread() into asm/a.out-core.h and makes it inline. This
is then included only where needed. This means that this bit of arch
code will be stored in the appropriate A.OUT binfmt module rather than
the core kernel.
(4) Drops A.OUT support for Blackfin (according to Mike Frysinger it's not
needed) and FRV.
This patch depends on the previous patch to move STACK_TOP[_MAX] out of
asm/a.out.h and into asm/processor.h as they're required whether or not A.OUT
format is available.
[jdike@addtoit.com: uml: re-remove accidentally restored code]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move STACK_TOP[_MAX] out of asm/a.out.h and into asm/processor.h as they're
required whether or not A.OUT format is available.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move Orion virtual mappings higher up in the address space, to free
up more kernel virtual address space.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Hack up the Orion port to distinguish between virtual and physical
addresses of register windows. This will allow moving virtual
mappings higher up in the address space, to free up more kernel
virtual address space.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Kill orion_early_putstr(), as it isn't used anywhere.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Use the new generic cmpxchg_local (disables interrupt). Also use the generic
cmpxchg as fallback if SMP is not set.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct user.u_ar0 is defined to contain a pointer offset on all
architectures in which it is defined (all architectures which define an
a.out format except SPARC.) However, it has a pointer type in the headers,
which is pointless -- <asm/user.h> is not exported to userspace, and it
just makes the code messy.
Redefine the field as "unsigned long" (which is the same size as a pointer
on all Linux architectures) and change the setting code to user offsetof()
instead of hand-coded arithmetic.
Cc: Linux Arch Mailing List <linux-arch@vger.kernel.org>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Håvard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm/elf.h, asm/page.h and asm/user.h don't export to userspace now, so we can
drop #ifdef __KERNEL__ for them.
[k.shutemov@gmail.com: remove #ifdef __KERNEL_]
Signed-off-by: Kirill A. Shutemov <k.shutemov@gmail.com>
Reviewed-by: David Woodhouse <dwmw2@infradead.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Kirill A. Shutemov <k.shutemov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'async-tx-for-linus' of git://lost.foo-projects.org/~dwillia2/git/iop:
async_tx: allow architecture specific async_tx_find_channel implementations
async_tx: replace 'int_en' with operation preparation flags
async_tx: kill tx_set_src and tx_set_dest methods
async_tx: kill ASYNC_TX_ASSUME_COHERENT
iop-adma: use LIST_HEAD instead of LIST_HEAD_INIT
async_tx: use LIST_HEAD instead of LIST_HEAD_INIT
async_tx: fix compile breakage, mark do_async_xor __always_inline
Add support for the S3C2412 to the S3C2410 frame buffer driver
by ensuring that any moved registers can be dealt with.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The two S3C SPI master drivers got merged without much review, so I just
noticed that they're doing something that the SPI core code is responsible
for, rather than any adapter driver: they try to register SPI devices.
This removes that support from those drivers so they act normally.
Interestingly, none of the current boards are affected. So it's a net code
shrink with no loss of functionality.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass a full set of flags to drivers' per-operation 'prep' routines.
Currently the only flag passed is DMA_PREP_INTERRUPT. The expectation is
that arch-specific async_tx_find_channel() implementations can exploit this
capability to find the best channel for an operation.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
(with Martin Schwidefsky <schwidefsky@de.ibm.com>)
The pgd/pud/pmd/pte page table allocation functions get a mm_struct pointer as
first argument. The free functions do not get the mm_struct argument. This
is 1) asymmetrical and 2) to do mm related page table allocations the mm
argument is needed on the free function as well.
[kamalesh@linux.vnet.ibm.com: i386 fix]
[akpm@linux-foundation.org: coding-syle fixes]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds gpiolib support for the PXA architecture:
- move all GPIO API functions from generic.c into gpio.c
- convert the gpio_get/set_value macros into inline functions
This makes it easier to hook up GPIOs provided by external chips like
ASICs and CPLDs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Minor ARM fixup from David Brownell folded into this ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
* at91:
[ARM] 4802/1: Fix typo and remove vague comment
[ARM] 4660/3: at91: allow selecting UART for early kernel messages
[ARM] 4739/1: at91sam9263: make gpio bank C and D irqs work
* ixp:
[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c
[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c
[ARM] 4807/2: ixp4xx: Merge nslu2-power.c into nslu2-setup.c
[ARM] 4806/1: ixp4xx: Ethernet support for the nslu2 and nas100d boards
[ARM] 4805/1: ixp4xx: Use leds-gpio driver instead of IXP4XX-GPIO-LED driver
[ARM] 4715/2: Ethernet support for IXDP425 boards
[ARM] 4714/2: Headers for IXP4xx built-in Ethernet and WAN drivers
[ARM] 4713/3: Adds drivers for IXP4xx QMgr and NPE features
[ARM] 4712/2: Adds functions to read and write IXP4xx "feature" bits
[ARM] 4774/2: ixp4xx: Register dsmg600 rtc i2c_board_info
[ARM] 4773/2: ixp4xx: Register nas100d rtc i2c_board_info
[ARM] 4772/2: ixp4xx: Register nslu2 rtc i2c_board_info
[ARM] 4769/2: ixp4xx: Button updates for the dsmg600 board
[ARM] 4768/2: ixp4xx: Button and LED updates for the nas100d board
[ARM] 4767/2: ixp4xx: Add bitops.h include to io.h
[ARM] 4766/2: ixp4xx: Update ixp4xx_defconfig, enabling all supported boards
* master:
[ARM] 4810/1: - Fix 'section mismatch' building warnings
[ARM] xtime_seqlock: fix more ARM machines for xtime deadlocking
[ARM] 21285 serial: fix build error
* misc:
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
* pxa:
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
[ARM] pxa: fix the warning of undeclared "struct pxaohci_platform_data"
[ARM] pxa: change set_kset_name() to direct name assignment for MFP sysclass
* realview:
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
This patch changes the REALVIEW_MPCORE configuration option to
REALVIEW_EB_ARM11MP since this is only specific to RealView/EB.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch modifies the get_irqnr_preamble macro to work with multiple
platforms at run-time by reading the address of the GIC controller from
the gic_cpu_base_addr variable. This variable is defined in core.c and
intialised in realview_eb.c (gic_init_irq).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the core-tile detection and only enables devices if the
corresponding tile is present. It currently detects the ARM11MPCore via
the core_tile_eb11mp() macro.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves the platform specific definitions from platform.h into
the board-eb.h file. It drops the INT_* definitions as they are no
longer used in irqs.h (moved to board-eb.h). It renames REALVIEW_*
macros to REALVIEW_EB_* or REALVIEW_EB11MP_* to distinguish between
standard EB and EB + the ARM11MPCore tile. The platform.h file contains
common definitions to the RealView platforms and it is only directly
included in board-*.h files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
