Now that the DEBUG_LL UART can be selected by a Kconfig choice, convert
the Samsung UART selection to use a set of bools rather than an int.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Previously the fclk rate was calculated by dividing the pll through
the divider value of the armdiv. With a real armdiv clk in place it's
possible to simply read its value, which does essentially the same.
This change makes the whole fdiv_fn function pointers supplied to
s3c2443_common_init_clocks and s3c2443_common_setup_clocks
obsolete, so remove it too.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is needed for making the armdiv clock common to S3C2443
and S3C2416/2450.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The ADC of the S3C2416/2450 SoC is 10 or 12 bit wide, has its
source selection in the register base+0x18 and its width
selection in bit 03 of the ADCCON register.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S3C2443-adc is 10 bit wide and has its mux-select
in an extra register at base+0x18
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move the platform device definitions from boards code to plat-samsung
to avoid multiple instances when multiple board support is compiled in.
The boards should select at least S5P_DEV_FIMC0 to enable FIMC support.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The adc blocks of S3C2443 and S3C2416 contain quirks not present
in the stock S3C24xx adc. Therefore allow them to alter the
device name via s3c_adc_setname.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The mux bits in the adccon register should be cleared only
if muxing is really done in ADCCON and not another register.
This patch introduces a conditional for this.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The adc blocks of the S3C2443 and S3C2416 define some
additional registers and bits.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch cleans up the Samsung resources in plat-samsung/devs.c
by using defined helpers at <linux/ioport.h>.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch merges each dev files to one devs.c file in
plat-samsung directory and this help to keep it more
easily to reduce plat- directories such as plat-s3c24xx
and plat-s5p.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves regarding s5p dev files to one devs.c file
in plat-samsung directory and this help to keep it more
easily.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves regarding s3c64xx dev files to one devs.c
file in plat-samsung directory and this help to keep it more
easily.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves regarding s3c24xx dev files to one devs.c
file in plat-samsung directory and this is required to merge
to plat-samsung.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves header files from plat-s5p to plat-samsung to
remove plat-s5p directory to make one plat-samsung directory
for Samsung SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves header files from plat-s3c24xx to plat-samsung to
remove plat-s3c24xx directory to make one plat-samsung directory for
Samsung SoCs. And this patch includes fixing coding style, too.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves SoC header files for supporting each SoCs to
plat-samsung directory. This is required to make one plat-
directory for Samsung SoCs.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sdhci platform helper function that sets up the default controller
configuration is removed for all Samsung platforms since such default
controller configuration can be handled by the driver.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds GPIO lines settings(HSYNC, VSYNC, VCLK and VD) for LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds all the resources for TV drivers and devices for Samsung
Exynos4 and S5PV210 platforms.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[m.szyprowski: squashed Exynos4 and S5PV210 patches and rewrote commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds hdmiphy dedicated i2c controller definitions.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[m.szyprowski: renamed to i2c-hdmiphy and squashed Exynos4 and S5PV210 patches]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung EXYNOS4412 SoC support.
The EXYNOS4412 integrates a ARM Cortex A9 quad-core.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to gpio-samsung.c, this patch updates the name of
regarding Samsung GPIO. Basically the samsung_xxx prefix is
used in gpio-samsung.c instead of s3c_xxx, because unified
name can reduce its complexity.
Note: some s3c_xxx stil remains because it is used widely.
It will be updated next time.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for Samsung GPIOs with one gpio driver
and removes old GPIO drivers which are drivers/gpio-s3c24xx.c,
gpio-s3c64xx.c, gpio-s5p64x0.c, gpio-s5pc100.c, gpio-s5pv210.c,
gpio-exynos4.c, gpio-plat-samsung.c, plat-samsung/gpio-config.c
and gpio.c to support each Samsung SoCs before. Because the
gpio-samsung.c can replace old Samsung GPIO drivers.
Basically, the gpio-samsung.c has been made by their merging
and removing duplicated definitions.
Note: gpio-samsung.c includes some SoC dependent codes and it
will be replaced next time.
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: squash the removing and adding patches]
[kgene.kim@samsung.com: fixes bug during to register of gpio_chips]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung EXYNOS4212 SoC support.
The EXYNOS4212 integrates a ARM Cortex A9 multi-core.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The default plat_data struct for TSADC is added in devs-ts.c
and duplication is removed from the following machines.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Moves similar functions to set SDHCI platform data for all Samsung
boards to a common location, thereby saves a few lines.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As all users of s3c24xx_dma_addr are gone now, remove it completely.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
clkdev framework uses global mutex to protect clock tree, so it is not
possible to call clk_get() in interrupt context. This patch fixes this
issue and makes system reset by watchdog call working again.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes the samsung specific enum type 's3c2410_dmasrc'
and uses 'dma_data_direction' instead.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds to support the DMA PL330 driver that uses
DMA generic API. Samsung sound driver uses DMA generic API
if architecture supports it. Otherwise, use samsung specific
S3C-PL330 API driver to transfer PCM data.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: removed useless variable]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since DMA generic APIs can be used for Samsung DMA now so that
the s3c-pl330 which includes Samsung specific DMA APIs can be
removed.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds common DMA operations which are used for Samsung DMA
drivers. Currently there are two types of DMA driver for Samsung SoCs.
The one is S3C-DMA for S3C SoCs and the other is PL330-DMA for S5P SoCs.
This patch provides funcion pointers for common DMA operations to DMA
client driver like SPI and Audio. It makes DMA client drivers support
multi-platform.
In addition, this common DMA operations implement the shared actions
that are needed for DMA client driver. For example shared actions are
filter() function for dma_request_channel() and parameter passing for
device_prep_slave_sg().
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds to support PL330-DMA driver on DMADEVICE for S5P SoCs.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current value for S5P64XX_CPU_MASK does not include the necessary
bits, which causes detection failure.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
[kgene.kim@samsung.com: changed the value]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The difference in CPU ID between S3C6400 and S3C6410 is a single bit and
that bit wasn't included in the mask causing the S3C6410 to be misdetected
as a S3C6400.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: changed the value]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch uses samsung_rev() to support variable silicon revision of
EXYNOS4210 so that can support for EXYNOS4210 REV0, REV1.0 and REV1.1.
Note: Need to change timer setting on REV0.
Acked-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds plat-samsung/cpu.c for detecting of cpu id and
silicon revision.
This patch was originally from Changhwan Youn <chaos.youn@samsung.com>
Acked-by: Changhwan Youn <chaos.youn@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With uart tx/rx/err interrupt handling moved into the driver for s3c64xx
and later SoC's, the uart interrupt handling in plaform code can be removed.
The uart device irq resources is reduced to one and the related unused
macros are removed.
Suggested-by: Grant Likely <grant.likely@secretlab.ca>
CC: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The soc_is_[name]() can be used to distinguish cpu at runtime.
This patch was originally from Changhwan Youn <chaos.youn@samsung.com>
Acked-by: Changhwan Youn <chaos.youn@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds chained IRQ enter/exit functions to timer
interrupt handler in order to function correctly on primary
controllers with different methods of flow control.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
WARNING: vmlinux.o(.text+0xf47c): Section mismatch in reference from the function samsung_bl_set() to the (unknown reference) .init.data:(unknown)
The function samsung_bl_set() references
the (unknown reference) __initdata (unknown).
This is often because samsung_bl_set lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
Add support for MFC device to plat-s5p, mach-exynos4, mach-s5pv210:
- clock support
- memory mapping and reserving
- s5p_device_mfc platform device
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds platform device s5p_device_fimd0 for EXYNOS4 FIMD0.
EXYNOS4 has two FIMDs(FIMD0, FIMD1). FIMD1 will be added later.
Some definitions used to enable EXYNOS4 FIMD0 are added.
Signed-off-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos4 and S5PC110(S5PV210) has Internal dma(idma) in AUDSS.
To support idma, register idma platform device.
and Exynos4 and S5PC110 has different IDMA address.
TO handle different IDMA address, register idma platform data
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch creates a common structure for LCD backlight
using PWM timer to be used by various Samsung boards.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Removes the duplication of default info structure in
dev-i2c[0 ~ 7].c files
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Calls the generic s3c_set_platdata function instead.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- Fixed: 12bit precision is lost at suspend/resume
- Updated: use pm_dev_ops
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In S5PV210/S5PC110/EXYNOS4, ADCMUX channel selection uses ADCMUX
register, not ADCCON register. This patch corrects the behavior of
SAMSUNG-ADC for such CPUs.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch allows the Samsung ADC driver to enable VDD regulator
at probe and resume and to disable at exit and suspend.
In a platform where ADC's VDD regulator is not "always-on", this
control is required although this patch does not provide fine-grained
power control (turning on the regulator only when being accessed).
However, if VDD regulator ("vdd" for the adc device) is not provided,
the regulator control will not be activated because there are platforms
that do not provide regulator for ADC device.
arch_initcall has been modified to module_init in order to allow
regulators to be available at probe.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds chained IRQ enter/exit functions to uart
interrupt handler in order to function correctly on primary
controllers with different methods of flow control.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a callback so that per-arch can do pre-sleep and post-resume
gpio configuration so that for the S3C64XX, the GPIO configuration
is restored before the sleep mode is cleared.
For the S3C64XX case, it means that the GPIOs get set back to normal
operation after the restore code puts the original configurations
back in after the
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The struct clk definition for Samsung platforms is extended to include
a instance of struct clk_lookup and a device name. When clocks are
registered using s3c24xx_register_clock function, the dev_id, con_id
and clk members are initialized with information from the struct clk
instance and struct clk_lookup member is registered.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit bcae8aeb32 "[ARM] S3C24A0: Initial architecture support files"
brought in a bunch of files while explicitly leaving out the corresponding
Kconfig entry, stating that the series is not complete.
More than 2.5 years later, the support for this has not seen any progress.
This is therefore dead code. If someone wants to revive this code, it is
always possible to retrieve it from the Git repository.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: DMA Cleanup as per sparse
ARM: SAMSUNG: Check NULL return from irq_alloc_generic_chip
Function declaration differs between file: dma.c and file:dma.h
and SPARSE (Documentation/sparse.txt) gives error messages
All dma channels are members of 'enum dma_ch' and not 'unsigned int'
Please have a look at channel definitions in:
arch/arm/mach-s3c64xx/include/mach/dma.h
arch/arm/plat-samsung/include/plat/s3c-dma-pl330.h
arch/arm/mach-s3c2410/include/mach/dma.h
So all arguments should be of type 'enum dma_ch'
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
tx_st_done is required for checking the transmission status of SPI
channels with different fifo levels
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There has been no #ifndef - #define - #endif protection for this
header file.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There are SoCs where attempting to enter a low power state is ignored,
and the CPU continues executing instructions with all state preserved.
It is over-complex at that point to disable the MMU just to call the
resume path.
Instead, allow the suspend finisher to return error codes to abort
suspend in this circumstance, where the cpu_suspend internals will then
unwind the saved state on the stack. Also omit the tlb flush as no
changes to the page tables will have happened.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
amba pl011: platform data for reg lockup and glitch v2
amba pl011: workaround for uart registers lockup
tty: n_gsm: improper skb_pull() use was leaking framed data
tty: n_gsm: Fixed logic to decode break signal from modem status
TTY: ntty, add one more sanity check
TTY: ldisc, do not close until there are readers
8250: Fix capabilities when changing the port type
8250_pci: Fix missing const from merges
ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
serial: ioremap warning fix for jsm driver.
8250_pci: add -ENODEV code for Intel EG20T PCH
The first and second arguments shouldn't concern platform code, so
hide them from each platforms caller.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the call to cpu_suspend into C code, and noticing that all the
s3c_cpu_save implementations are now identical, we can move this
into the common samsung code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As we have core code dealing with CPU suspend/resume, we can
re-initialize the CPUs exception banked registers via that code rather
than having platforms deal with that level of detail. So, move the
call to cpu_init() out of platform code into core code.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes the way of comparison for handling of two or more
clock sources for UART.
For example, if just only one clock source is defined even though
there are two clock sources for UART, the serial driver does not
set proper clock up. Of course, it is problem.
So this patch changes the condition of comparison to avoid useless
setup clock and adds a flag 'NO_NEED_CHECK_CLKSRC' which means
selection of source clock is not required.
In addition, since the Exynos4210 has only one clock source for UART
this patch adds the flag into its common_init_uarts().
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's no place to use these functions.
and actually no need to set the platform data.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Changed the SPI platform device name from S5P6450 to S5P64x0 as it is
defined common for both S5p6440 and S5P6450 in dev-spi.c of S5P64x0.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/pch_gpio: Support new device ML7223
gpio: make gpio_{request,free}_array gpio array parameter const
GPIO: OMAP: move to drivers/gpio
GPIO: OMAP: move register offset defines into <plat/gpio.h>
gpio: Convert gpio_is_valid to return bool
gpio: Move the s5pc100 GPIO to drivers/gpio
gpio: Move the s5pv210 GPIO to drivers/gpio
gpio: Move the exynos4 GPIO to drivers/gpio
gpio: Move to Samsung common GPIO library to drivers/gpio
gpio/nomadik: add function to read GPIO pull down status
gpio/nomadik: show all pins in debug
gpio: move Nomadik GPIO driver to drivers/gpio
gpio: move U300 GPIO driver to drivers/gpio
langwell_gpio: add runtime pm support
gpio/pca953x: Add support for pca9574 and pca9575 devices
gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535
It's common gpiolib for recent Samsung SoCs. Move to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
ARM: bcmring: convert to use sp804 clockevents
ARM: bcmring: convert to sp804 clocksource
ARM: 6912/1: bcmring: Add clkdev table in init_early
clockevents: ARM sp804: obtain sp804 timer rate via clks
clockevents: ARM sp804: allow clockevent name to be specified
clocksource: ARM sp804: obtain sp804 timer rate via clks
clocksource: ARM sp804: allow clocksource name to be specified
clocksource: convert OMAP1 to 32-bit down counting clocksource
clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
clocksource: convert SPEAr platforms 16-bit up counting clocksource
clocksource: convert Integrator/AP 16-bit down counting clocksource
clocksource: convert W90x900 24-bit down counting clocksource
clocksource: convert ARM 32-bit down counting clocksources
clocksource: convert ARM 32-bit up counting clocksources
clocksource: add common mmio clocksource
ARM: update sa1100 to reflect PXA updates
ARM: omap1: convert to using readl/writel instead of volatile struct
ARM: omap1: delete useless interrupt handler
ARM: s5p: consolidate selection of timer register
ARM: 6939/1: fix missing 'cpu_relax()' declaration
...
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
The generic chip infrastructure has had a Kconfig symbol added so we need
to select that for the kernel to link now we're using the generic IRQ
chip infrastructure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2416, S3C2443 and S3C2450 includes a USB High-Speed Gadget controller module.
This patch adds the following for supporting this controller.
1. Definition for USB High-Speed controller base address.
2. Platform device instantiation.
3. Declaration for platform data structure.
4. Functionality to setup platform data for the controller.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols. This usually means that no global variables can
be marked static unless they're also const.
Let's remove the static qualifier from current offenders, or turn them
into const variables when possible. Next commit will ensure the build
fails if one of those is reintroduced due to otherwise enforced coding
standards for the kernel.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Replace sysdev classes and struct sys_device objects used for "core"
power management by Samsung platforms with struct syscore_ops objects
that are simpler.
This generally reduces the code size and the kernel memory footprint.
It also is necessary for removing sysdevs entirely from the kernel in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
s3c_pm_show_resume_irqs() is used by some s3c_pm_arch_show_resume_irqs()
implementations, which get included through mach/pm-core.h. Add __maybe_unused
to silence warnings when it isn't used (e.g. on S3C64XX platforms).
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error that occurs on enabling the Samsung
specific PM CRC check code. Missed removing this reference of
s3c_sleep_save_phys during move to generic cpu suspend/resume
support.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Reorder
irq_set_chip()
irq_set_chip_data()
irq_set_handler()
to
irq_set_chip()
irq_set_handler()
irq_set_chip_data()
so the next patch can combine irq_set_chip() and irq_set_handler() to
irq_set_chip_and_handler().
Automated conversion with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes CPU idmask of S5P64X0 and EXYNOS4210
and its comparison method because just want to use CPU
id for it.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
This patch removes all global data from common s5p gpio interrupt
handler code. This enables to reuse this code on EXYNOS4 platform.
Instead of global data (IRQ_GPIOINT interrupt number,
S5P_GPIOINT_GROUP_MAXNR groups count), a s5p_register_gpioint_bank()
function is introduced. It is aimed to be called from gpiolib init.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds the device definitions, platform specific initialization
and clocks for SATA on ARMLEX4210.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support suspend to ram for EXYNOS4210.
As a note, this includes function of outer cache flush
because it is used before entering PM.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for fourth FIMC platform device definition and define
resources for FIMC modules on EXYNOS4 machines.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Ensures that the declaration agrees with the definition and makes sparse
happy.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch does the following:-
1. It moves file pwm.c from plat-s3c24xx to plat-samsung. This will
enable all machines with Samsung SoCs to make use of the same code.
2. The device definitions have been separated to a new file dev-pwm.c
for better clarity and structure.
3. It will enable all Samsung S3C and S5P series SoC's to use common
PWM Kconfig definition.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates device support of EXYNOS4 according to the change of
ARCH name, EXYNOS4.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
s3c24xx_ts_set_platdata is annotated __init and not used by any module,
thus don't export it.
This patch fixes below warning:
WARNING: arch/arm/plat-samsung/built-in.o(__ksymtab+0x90): Section mismatch
in reference from the variable __ksymtab_s3c24xx_ts_set_platdata to the
function .init.text:s3c24xx_ts_set_platdata()
The symbol s3c24xx_ts_set_platdata is exported and annotated __init
Fix this by removing the __init annotation of s3c24xx_ts_set_platdata
or drop the export.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Previously we were relying on it being pulled in by other headers for
the prototype of s3c24xx_irq_suspend() and s3c24xx_irq_resume().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support System MMU for S5PV310 and S5PC210.
Signed-off-by: Donguk Ryu <du.ryu@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: changed SYSMMU config name]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for clock information exposed to debug-fs interface.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
[kgene.kim@samsung.com: removed useless empty lines]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There are few functions marked as __init, but exported to modules in
devices declaration files.
s3c_nand_set_platdata() and s3c24xx_ts_set_platdata() are used only by
boards init code now, so remove EXPORT_SYMBOL() for them.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2443 has two-bits pull-up/pull-down configuration fields in GPIO
registers, but values are differ from other SoCs with two-bits
configuration. gpio-cfg-helpers.h already has prototypes for
s3c2443-style pull-up/down methods, so implement them.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Samsung S3C2416 has two SDHCI controllers compatible with other
Samsung's SoCs (S3C64XX, S5PC100 etc...).
Add required platform setup code that the devices can be used with
sdhci-s3c driver.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
[kgene.kim@samsung.com: change to __raw_{readl,writel} from {readl,writel}]
[kgene.kim@samsung.com: build error fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When GENERIC_HARDIRQS_NO_DEPRECATED is enabled, a number of struct
irq_desc members stop being directly accessible, and need to be
accessed via the irq_data struct instead -- this patch fixes up the
plat-samsung sites that still access those members directly.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There may be up to two MIPI CSI slave interfaces depending on the SoC version.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support Power Domain for S5PV310 and S5PC210.
Signed-off-by: Changhwan Youn <chaos.youn at samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch implements Power Domain control based on Runtime PM framework.
Each Power Domain is represented by a Power Domain device and the devices
belong to these Power Domains should be set as a child device of the Power
Domain devices. The corresponding drivers of the devices should implement
Runtime PM to control the Power Domains.
Signed-off-by: Changhwan Youn <chaos.youn at samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Conver the VIC timer interrupts to use the irq_ versions of the IRQ
operatiosn introduced in 2.6.37, storing the mask for the timer
interrupt in the chip_data of the irq_data in order to save having to
do a substraction and a shift on every operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Convert to the new irq_ versions of the IRQ operations. As well as
the textual substituion of irq_data for the raw IRQ number we also
convert the register base lookup to in s3c_irq_uart_base() to pick
the irq_data up directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Begin converting Samsung platforms over to
these methods by converting s3c_irqext_wake() with a simple textual
substitution.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Segregate I2S devices for S5P6440 and S5P6450.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Currently the {set,get}_pull callbacks of the s3c24xx_gpiocfg_default structure
are initalized via s3c_gpio_{get,set}pull_1up. This results in a linker
error when only CONFIG_CPU_S3C2442 is selected:
arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f4): undefined reference to
`s3c_gpio_getpull_1up'
arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f8): undefined reference to
`s3c_gpio_setpull_1up'
The s3c2442 has pulldowns instead of pullups compared to the s3c2440.
The method of controlling them is the same though.
So this patch modifies the existing s3c_gpio_{get,set}pull_1up helper functions
to take an additional parameter deciding whether the pin has a pullup or pulldown.
The s3c_gpio_{get,set}pull_1{down,up} functions then wrap that functions passing
either S3C_GPIO_PULL_UP or S3C_GPIO_PULL_DOWN.
Furthermore this patch sets up the s3c24xx_gpiocfg_default.{get,set}_pull fields
in the s3c244{0,2}_map_io function to the new pulldown helper functions.
Based on patch from "Lars-Peter Clausen" <lars@metafoo.de>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ensure that the prototype agrees with the definition and stop sparse
complaining when building the file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The ASoC uses common DMA driver for Audio devices. So it makes
sense to a common audio-dma device shared across all platforms.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Define platform devices for all audio devices found on S5PV310
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add new defined and data structures in order to prepare for
new I2S driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds the s3c_gpio_getpull() API that has been missed in the
plat-samsung/gpio-config.c and actullay there is its extern declaration
in plat/gpio-cfg.h.
Signed-off-by: Daein Moon <moon9124@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
This patch moves the start address of Samsung SoCs' VA space so that
can use more vmalloc()/ioremap() space. Of course need to change the
VMALLOC_END for it.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves DMA clock enable functionality into pl330_probe() of
plat-samsung/s3c_pl330.c (PL330 DMAC driver) and disable functionality
into pl330_remove().
For now according to clock policy of Samsung SoCs' mainline, clocks which
are used in the driver should be controlled by each own.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
[kgene.kim@samsung.com: minor title and comment edit]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add S/PDIF platform device to support S/PDIF PCM audio
on S5PV210.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add S/PDIF platform device to support S/PDIF PCM audio
on S5PC100.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PV310 and S5PC210 support more I2C devices than previous SoCs.
Add the device support code for them.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The name of the I2C2 and I2C3 interrupt should be IIC2 and IIC3
instead of CAN0 and CAN1.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds clock types into platform data to support
external clock divider instead of internal clock divider.
It is defined that what kinds of clock type is used in machine.
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds to change bus width and host capability of HSMMC,
when HSMMC is only configured with another value of bus width
and host capability from default one.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds initialization HSMMC device information.
And HSMMC platform data like card detect, data bus width
and capability is configured.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A number of the SDHCI code configure a GPIO to a special function
and remove any pull-up, so add s3c_gpio_cfgrange_nopull() as a
wrapper to the s3c_gpio_cfgall_range() to make the code that
calls it fit on one line.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a function to configure a range of GPIOs function and
pull in one go, mainly for the SDHCI and framebuffer helpers
which tend to do this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: Fix small comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add s3c_gpio_cfgpin_range() to configure a range of pins to the given
value. This is useful for a number of blocks where the pins are in order
and saves multiple calls to s3c_gpio_cfgpin().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
This patch adds suspend-to-ram support for S5PV210.
Note. This patch is confirmed on SMDKV210 and SMDKC110 board.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a common callback for gpio_to_irq() for external and
gpio interrupts for Samsung SoCs.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: moved samsung_gpiolib_to_irq() for s3c24xx build]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds common code to enable support of GPIO interrupt on
S5P SoCs.
The total number of GPIO pins is quite large on S5P SoCs. Registering
irq support for all of them would be a resource waste. Because of that
the interrupt support for standard GPIO pins is registered dynamically
by the s5p_register_gpio_interrupt() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch replaces the device name assignment method from string assignment
to set_name method for all s3c24xx machines and adds device core file.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The s5p64x0_sysclass should be used in place of the obselete s5p6440_sysclass.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves DMA support files in the mach-s5p64x0
for S5P6440 and S5P6450 SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
This patch updates Audio and SPI for S5P6440 and S5P6450 SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
The patch below updates broken web addresses in the arch directory.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch moves OneNAND device definitions from mach-s5pv210 to plat-s5p
so that can support it commonly.
Note: S5PC110 and S5PC210 have same OneNAND driver.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Serial drivers call get_clock() very early, before platform bus
has been set up, this requires a special check to let them get
a proper clock. Without this patch, a serial console is broken
on S5PV310 and S5PC210 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: fix coding-style]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This patch removes following unused codes for removing build warnings.
arch/arm/plat-samsung/adc.c:438: warning: unused variable 'flags'
arch/arm/mach-s5pv210/clock.c:176: warning: 's5pv210_clk_ip4_ctrl' defined but not used
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Newer SoCs have the SPI clock scaling control in platform's
clock management unit. Inorder for such SoCs to work, we need
to check the flag clk_from_cmu before making any clock changes.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes bug on gpio drive strength helper function.
The offset should be like follwoing.
- off = chip->chip.base - pin;
+ off = pin - chip->chip.base;
In the s5p_gpio_get_drvstr(),
the second line is unnecessary, because overwrite drvstr.
drvstr = __raw_readl(reg);
- drvstr = 0xffff & (0x3 << shift);
And need 2bit masking before return the drvstr value.
drvstr = drvstr >> shift;
+ drvstr &= 0x3;
In the s5p_gpio_set_drvstr(), need relevant bit clear.
tmp = __raw_readl(reg);
+ tmp &= ~(0x3 << shift);
tmp |= drvstr << shift;
Reported-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes on defined drive strength value for GPIO.
According to data sheet, if we want drive strength 1x, the value
should be 00(b), if 2x should be 10(b), if 3x should be 01(b),
and if 4x should be 11(b). Also fixes comment(from S5C to S5P).
Reported-by: Janghyuck Kim <janghyuck.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Each board can override the default sdhci host capabilities.
Some board has broken features by hardwares and support 8-bit bandwidth.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fairly simple conflicts, the most serious ones are the i.MX ones which I
suspect now need another rename.
Conflicts:
arch/arm/mach-mx2/clock_imx27.c
arch/arm/mach-mx2/devices.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-zoom2.c
sound/soc/fsl/mpc5200_dma.c
sound/soc/fsl/mpc5200_dma.h
sound/soc/fsl/mpc8610_hpcd.c
sound/soc/pxa/spitz.c
* 'for-linus/samsung-2635' of git://git.fluff.org/bjdooks/linux:
DMAENGINE: correct PL080 register header file
ARM: SAMSUNG: Fix on build warning about dependency in Kconfig
ARM: SMDK6410: Make virtual screen twice depth of real
ARM: S3C64XX: Update consistent DMA size to 8MiB
ARM: S3C64XX: Add audio support to SmartQ
ARM: S3C64XX: Framebuffer fix for SmartQ5
ARM: S3C64XX: Set wifi and iNAND as permanently connected SD devices on SmartQ boards
ARM: S3C64XX: Move SmartQ LCD control platform definition to shared file
ARM: mach-real6410: add sdhc device support
ARM: mach-real6410: add dm9000 ethernet support for mach-real6410
ARM: S3C64XX: Support for Real6410
Fix up trivial conflicts in arch/arm/mach-s3c64xx/mach-smartq5.c
("remove pixclock" vs "Framebuffer fix for SmartQ5")
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (226 commits)
ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
ARM: 6322/1: imx/pca100: Fix name of spi platform data
ARM: 6321/1: fix syntax error in main Kconfig file
ARM: 6297/1: move U300 timer to dynamic clock lookup
ARM: 6296/1: clock U300 intcon and timer properly
ARM: 6295/1: fix U300 apb_pclk split
ARM: 6306/1: fix inverted MMC card detect in U300
ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID
ARM: 6294/1: etm: do a dummy read from OSSRR during initialization
ARM: 6292/1: coresight: add ETM management registers
ARM: 6288/1: ftrace: document mcount formats
ARM: 6287/1: ftrace: clean up mcount assembly indentation
ARM: 6286/1: fix Thumb-2 decompressor broken by "Auto calculate ZRELADDR"
ARM: 6281/1: video/imxfb.c: allow usage without BACKLIGHT_CLASS_DEVICE
ARM: 6280/1: imx: Fix build failure when including <mach/gpio.h> without <linux/spinlock.h>
ARM: S5PV210: Fix on missing s3c-sdhci card detection method for hsmmc3
ARM: S5P: Fix on missing S5P_DEV_FIMC in plat-s5p/Kconfig
ARM: S5PV210: Override FIMC driver name on Aquila board
ARM: S5PC100: enable FIMC on SMDKC100
...
Fix up conflicts in arch/arm/mach-{s5pc100,s5pv210}/cpu.c due to
different subsystem 'setname' calls, and trivial port types in
include/linux/serial_core.h
S5PV210 SoCs allow enabling/disabling DMA channels per window. For a
window to display data from framebuffer memory, its channel has to be
enabled.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add VSYNC interrupt support and an ioctl that allows waiting for it.
Interrupts are turned on only when needed.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Supports all bpp modes.
The PRTCON register is used to disable in-hardware updates of registers
that store start and end addresses of framebuffer memory. This prevents
display corruption in case we do not make it before VSYNC with updating
them atomically. With this feature there is no need to wait for a VSYNC
interrupt before each such update.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the palette setup code from the header files and put it into the
main driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: KyungMin Park <kyungmin.park.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the variant and window variant structures with the necessary
changes to support the older style of hardware where these are not in the
same place.
Add the support for the s3c2443/s3c2416 hardware by using the
platform-device s3c2443 to cover both, and add the initialisation data for
these.
Also change to including just the v4 header files for the moment until the
last of the merging of these is sorted out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: KyungMin Park <kyungmin.park.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the various header files that configure this driver and use the
platform device name to select the correct configuration at probe time.
Currently this does not remove the header files, only updates the driver
and the relevant platform files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: KyungMin Park <kyungmin.park.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It has been working fine at 16bpp but in case of pixel format more then
24bpp it would occur distortedness situation on that mode. so this patch
set the word swap control bit of WINCONx to 1 as default value. but it
should be set to 0 in case that each ENLOCAL bit of WINCON0 ~ 2 registers
is enabled. this issue would be solved with local path feature soon.
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Reviewed-by: KyungMin Park <kyungmin.park.samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s5pv210 has five window layers (window0 ~ 4), among them, window0 ~ 2
could be used for local path with fimc(capture device) and fimd writeback
feature so this patch makes default window layer for UI to be set at
machine code.
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Reviewed-by: KyungMin Park <kyungmin.park.samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the dedicated FIFO mode on newer SoCs such as the S5PV210
partly to improve support and to fix the bug where any non-EP0 IN endpoint
requires its own FIFO allocation.
To fix this, we ensure that any non-zero IN endpoint is given a TXFIFO
using the same allocation method as the periodic case (all our current
hardware has enough FIFOs and FIFO memory for a 1:1 mapping) and ensure
that the necessary transmission done interrupt is enabled.
The default settings from reset for the core point all EPs at FIFO0,
used for the control endpoint. However, the controller documentation
states that all IN endpoints _must_ have a unique FIFO to avoid any
contention during transmission.
Note, this leaves us with a large IN FIFO for EP0 (which re-uses the
old NPTXFIFO) for an endpoint which cannot shift more than a pair of
packets at a time... this is a waste, but it looks like we cannot
re-allocate space to the individual IN FIFOs as they are already
maxed out (to be confirmed).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix on inclusion mach/gpio.h on plat-samsung/gpiolib.c
since new C preprocessor directives.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: minor title and message fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
FIMC (CAMIF) device is a camera interface embedded in S3C/S5P Samsung
SOC series. It supports ITU-R BT.601/656 and MIPI-CSI2 standards,
memory to memory operations, color conversion, resizing and rotation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates RTC registers for support Alarm IRQ and Time Tick.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Taekgyun Ko <taeggyun.ko@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On some Samsung SoCs not all SDHCI controllers have card detect (CD)
line. For some embedded designs it is not even needed, because ususally
the device (like SDIO flash memory or wifi controller) is permanently
wired to the controller. There are also systems which have a card detect
line connected to some of the external interrupt lines or the presence
of the card depends on some other actions (like enabling a power
regulator).
This patch adds all required changes to platform support code, so
another patch, which extends the driver with support for the new card
detection methods can be applied.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title and coding-style fixes]
[kgene.kim@samsung.com: fix build errors]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds hsmmc3 device definition in plat-samsung. Because now
S5PV210 can support 4 hsmmc such as hsmmc0, hsmmc1, hsmmc2 and hsmmc3
and that can be used in further Samsung SoCs.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch implements s3c_adc_setname() for Samsung SoCs.
Also updates its usage in S3C64XX, S5P6440, and S5PV210.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Following has been added:
- Common CF Platform device definition
- Platform data strucure definition
- CF controller register definitions
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is intended to replace a number of sites in the Samsung kernel
where the same thing is being repeated in specific platform setting
code. See next patches for replacements.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: This is for building test]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch reduces the virtual memory allocated for WDT device from 1M
to 1K.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
This patch adds timer support for S5PV310. Until now, all S5P SoCs
use CONFIG_ARCH_USES_GETTIMEOFFSET macro as a default configuration.
Instead,S5PV310 implements clocksource and clock_event_device to
support the high resolution timer and tickless system.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for the FRACVAL register on the newer UART blocks which provides
the same function as UDIVSLOT register but the FRACVAL is easier to implement.
To support UDIVSLOT register, UDIVSLOT table search is necessary though
supporting FRACVAL only needs the index value of UDIVSLOT table.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Acked-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HSMMC on SMDKV210, and gpio configuration for
S5PV210 hsmmc3.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the keypad device platform helpers for S5PV210 cpu.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: adp5588-keypad - fix NULL dereference in adp5588_gpio_add()
Input: cy8ctmg110 - capacitive touchscreen support
Input: keyboard - also match braille-only keyboards
Input: adp5588-keys - export unused GPIO pins
Input: xpad - add product ID for Hori Fighting Stick EX2
Input: adxl34x - fix leak and use after free
Input: samsung-keypad - Add samsung keypad driver
Input: i8042 - reset keyboard controller wehen resuming from S2R
Input: synaptics - set min/max for finger width
Input: synaptics - only report width on hardware that supports it
Input: evdev - signal that device is writable in evdev_poll()
Input: mousedev - signal that device is writable in mousedev_poll()
Input: change input handlers to use bool when possible
Input: document the MT event slot protocol
Input: introduce MT event slots
Input: usbtouchscreen - implement reset_resume
Input: usbtouchscreen - implement runtime power management
Input: usbtouchscreen - implement basic suspend/resume
Input: Add ATMEL QT602240 touchscreen driver
Input: fix signedness warning in input_set_keycode()
...
This patch adds support for keypad driver running on Samsung cpus. This
driver is tested on GONI and Aquila board using S5PC110 cpu.
[ch.naveen@samsung.com: tested on SMDK6410, SMDKC100, and SMDKV210]
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes on wrong function name in include/plat/sdhci.h for Samsung.
The 's5pc100_default_sdhci0()' function should be chnaged to
's5pv210_default_sdhci0()'. Because 's5pv210_default_sdhci0()' must be pair.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes the following compilation problem if only NCP machine
is selected:
arch/arm/mach-s3c64xx/s3c6410.c: In function 's3c6410_map_io':
arch/arm/mach-s3c64xx/s3c6410.c:51: error: implicit declaration of function 's3c6410_default_sdhci2'
And also adds missed 's3c6400_default_sdhci2'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix and added comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Update the documentation on the gpio configuration calls to add more
references to useful information and also to document the values that
are passed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for the S3C64xx SoC to the generic S3C RTC driver.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When saving GPIOs during suspend/resume we need skip missing GPIO banks, not
trying get corresponding chip again and again in infinite loop.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
[ben-linux@fluff.org: shorten subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Add support for wakeup-mask style interrupts that share a
single mask register for various different interrupts. This
registers a set of interrupt->bit mappings and the register
they belong to.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change local_irq disable calls to use spinlocks to ensure that the
ADC driver data is protected against multiple access..
Note, this does not protect the client's data, and the client should
ensure it does not make multiple calls to the ADC driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves the definitions of watchdog timer device from
plat-s3c24xx to plat-samsung. This will enable all Samsung S3C
and S5P series SoC's to use common WDT device definition.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define platform devices for all audio devices found on S5PC100
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds sdhci platform helpers required by sdhci-s3c driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds I2C platform helpers required by s3c2440-i2c driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds common framebuffer device helpers and register defines
for S5PV210 based machines.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds setup code for Samsung OneNAND controller driver. The
driver needs to be aware on which SoC it is running, so the actual
device id is being changed in cpu init code. S3C64xx SoCs have 2 OneNAND
controllers while S5PC100 and S5PC110 has only one.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[ben-linux@fluff.org: sort map.h entries]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves S5PC100 SoC support to plat-s5p framework. Most
periperal support code has been already moved from plat-s5pc1xx to
mach-s5pc100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the arch/arm/mach-s3c64xx/dev-ts.c file to arch/arm/plat-samsung and
rename the Kconfig entry appropriately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch implements cfg_gpio function for Samsung touchscreen.
And also modifies the H1940 machine respectively.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the touchscreen platform device definition for S3C64XX boards.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This moves mach-s3c2410/include/mach/ts.h to plat-samsung/include/plat/ts.h in
order to prepare for s3c64xx support in the touchscreen driver.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Driver strength parameter can be changed not only on S5PC100 but also
on S5PV210/S5PC110 platforms, so move the helper functions to the common
plat-samsung directory.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define platform devices for all audio devices found on S5P6440
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define platform devices for all audio devices found on S5P6442
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define platform devices for all audio devices found on S5PV210
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The pm-gpio.c code was incrementing the gpio_nr from the nr_gpios
field and the bank-bank offset inside the loop, and also in the
for() loop with a ++.
Remove the ++, as the number is already at the next GPIO, thus
ensuring that we don't skip a gpio bank by accident.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the S3C_FB_MAX_WIN to the platform data to avoid
having to include the registers with the platform data.
Set S3C_FB_MAX_WIN to 5, which is the maximum that any
of the current hardware can do and the cost of having
it set to this for all is minimal (at least for the
platform data case), then always leave this as the maximum
for the systems supported.
Also remove the inclusion of <mach/regs-fb.h> from
the device definition in arch/arm/plat-samsung
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds the xusbxti clock to S3C64XX platform.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Latest Samsung SoCs have one or more PL330 as their DMACs. This patch
implements the S3C DMA API for PL330 core driver.
The design has been kept as generic as possible while keeping effort to
add support for new SoCs to the minimum possible level.
Some of the salient features of this driver are:-
o Automatic scheduling of client requests onto DMAC if more than
one DMAC can reach the peripheral. Factors, such as current load
and number of exclusive but inactive peripherals that are
supported by the DMAC, are used to decide suitability of a DMAC
for a particular client.
o CIRCULAR buffer option is supported.
o The driver scales transparently with the number of DMACs and total
peripherals in the platform, since all peripherals are added to
the peripheral pool and DMACs to the controller pool.
For most conservative use of memory, smallest driver size and best
performance, we don't employ legacy data structures of the S3C DMA API.
That should not have any affect since those data structures are completely
invisible to the DMA clients.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves RTC device definitions from mach-s3c64xx
to plat-samsung, to enable the other SoCs to use same device
definition.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves ADC device definition to plat-samsung.
Because that is generic to the S3C64XX and S5P Series SoCs.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
All other functions have the channel argument of type 'unsigned int'
the s3c2410_dma_devconfig also accept the same value as argument but
treat it as type 'int'. Remove this anomaly by make it 'unsigned int'.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move HWMON platform definition from plat-s3c24xx to plat-samsung
and adjust mach-bast to use the new s3c_hwmon_set_platdata().
This allows usage of dev-hwmon by other Samsung SoCs.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch removes static of s5p6440_sysclass, s5p6442_sysclass,
and s5pv210_sysclass for defintion as extern.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add locking to each GPIO bank to allow for SMP capable code
to use the gpiolib functions. See the gpio-core.h header file
for more information.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add arch/arm/mach-s3c2416 for support of the Samsung S3C2416 SoC.
This patch adds support of the S3C2416 SoC, clocks, timers,
and initial IRQ support (without support of secondary set of registers).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
[ben-linux@fluff.org: removed files to be reworked, fixed conflicts]
[ben-linux@fluff.org: use s3c2443 reset instead of specific reset code]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add s3c_disable_clocks() and change the clock registration code to use
the s3c_register_clocks() followed by s3c_disable_clocks() instead of
the loops it was using.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C6400 EPLL code matches the S3C2416 and compatible SoCs, so move
it from mach-s3c64xx into <plat/pll.h> for easy reuse.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the necessary 1,2 and 4 bit configuration read calls for the new
gpio code to allow removal of the old s3c24xx gpio code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the necessary gpio configuration helper for the devices which
have a single-bit pull-up resistor disabled.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for s3c_gpio_setcfg() and s3c_gpio_setpull() implementations
to get ready for removal of the specific code being used by s3c24xx.
Also rename the s3c_gpio_setcfg_s3c24xx_banka to s3c_gpio_setcfg_s3c24xx_a
as seen in the header file to correct a build warning.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The header for I2Sv2
linux/arch/arm/plat-s3c/include/plat/regs-s3c2412-iis.h
contains only controller specific definitions and nothing
SoC specific. So, it could be moved to sound/soc/s3c24xx/
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The decleration of error() as static in the platform specific uncompress
code in arch/arm/plat-samsung/include/plat/uncomopress.h causes the build
of the uncompressor to break. Remove it, as it is no longer needed.
arch/arm/boot/compressed/decompress.o: In function `gunzip':
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:67: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:73: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:80: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:95: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:152: undefined reference to `error'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Reset period_ns and duty_ns values in suspend handler to avoid skip of
configuration if same values passed to pwm_config;
Restore invertion bit in resume handler.
Without this patch PWM works incorrectly after resume from suspend.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
This patch defines the platform device and the resources: IRQ, DMA and MEM,
needed by the AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Samsung S5P6442 CPU. This patch also adds
an entry for S5P6442 cpu in plat-s5p cpu table.
Signed-off-by: Adityapratap Sharma <aditya.ps@samsung.com>
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
IRQ should be disabled on suspend and re-enabled on resume.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the Kconfig entries from plat-s3c to plat-samsung and plat-s3c24xx
as necessary. The S3C_BOOT entries and the DMA configuration can go to
plat-samsung. The low-level UART configurations are currently S3C2XX
specific and can go to plat-s3c24xx.
Eliminating plat-s3c from the build process will be submitted seperately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the init.c and time.c files to plat-samsung from plat-s3c, thus
clearing the last files that are being built in here.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the map-base file to plat-samsung. To make the move easier, we do not
change the S3C_ prefix on many of the items as this would involve going
through altering all the dependencies.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move common headers from plat-s3c's include/plat directory into plat-samsung.
No need to fix any files, these are still included via <plat/>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
dma-plat.h is the last file left in plat-s3c64xx, but to remove it we
must also change the use of dma-plat.h by the core code and the s3c24xx
implementation.
Rename the s3c24xx dma-plat.h in the common plat-samsung directory as it
may be used for other ports. Move the specific dma bits into the
mach-s3c64xx directory and update the build as needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Turn the init sequence of
s3c24xx_register_baseclocks(xtal);
s3c64xx_register_clocks();
s3c6400_register_clocks(S3C6410_CLKDIV0_ARM_MASK);
into a single call as this is now contained within one file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C64XX SoC series support 12bit ADC data, enable this and
mask the data accordingly.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The SPI controller platform devices should be compiled in
independent of the driver support, otherwise we might end
up with dev-spi built as kernel module.
Change this to make every machine select if it has some SPI
device and wants to build device definitions.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add an error print to s3c24xx_register_clocks to provide more useful
information when failing to register the clock.
I belive this was originally left out due to the possibility of a
problem with low-level debugging code. However, if the low-level
debug code is not functional by now there will be a whole other set of
problems being presented to the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Squash the SDHCI setup for both the S3C6400 and S3C6410 into one file and
make the S3C6410 case use the S3C6400 code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
ARM: SAMSUNG: Fix null pointer dereference in ADC driver
Use struct adc_device instead of relying on client (which could be
NULL) when checking for SoC type.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
They are not exported, they are referenced via vtables.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the pm-check.c file to plat-samsung for all Samsung SoC users, and
update Kconfig names to make them SAMSUNG_ instead of S3C2410_
Sed expresions used to make the change:
s/S3C2410_PM_DEBUG/SAMSUNG_PM_DEBUG/g
s/S3C2410_PM_CHECK/SAMSUNG_PM_CHECK/g
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the PWM driver support to plat-samsung, as these PWM blocks are
close enough across the current range to be supported by this driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
