Tx timestamps are looped onto the error queue on top of an skb. This
mechanism leaks packet headers to processes unless the no-payload
options SOF_TIMESTAMPING_OPT_TSONLY is set.
Add a sysctl that optionally drops looped timestamp with data. This
only affects processes without CAP_NET_RAW.
The policy is checked when timestamps are generated in the stack.
It is possible for timestamps with data to be reported after the
sysctl is set, if these were queued internally earlier.
No vulnerability is immediately known that exploits knowledge
gleaned from packet headers, but it may still be preferable to allow
administrators to lock down this path at the cost of possible
breakage of legacy applications.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
(v1 -> v2)
- test socket CAP_NET_RAW instead of capable(CAP_NET_RAW)
(rfc -> v1)
- document the sysctl in Documentation/sysctl/net.txt
- fix access control race: read .._OPT_TSONLY only once,
use same value for permission check and skb generation.
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS (Receive Side Scaling) typically uses Toeplitz hash and a 40 or 52 bytes
RSS key.
Some drivers use a constant (and well known key), some drivers use a random
key per port, making bonding setups hard to tune. Well known keys increase
attack surface, considering that number of queues is usually a power of two.
This patch provides infrastructure to help drivers doing the right thing.
netdev_rss_key_fill() should be used by drivers to initialize their RSS key,
even if they provide ethtool -X support to let user redefine the key later.
A new /proc/sys/net/core/netdev_rss_key file can be used to get the host
RSS key even for drivers not providing ethtool -x support, in case some
applications want to precisely setup flows to match some RX queues.
Tested:
myhost:~# cat /proc/sys/net/core/netdev_rss_key
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41:36:40:74:b6:15:ca:27:44:aa:b3:4d:72
myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
0: 0 1 2 3 4 5 6 7
RSS hash key:
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more common dynamic_debug capable net_dbg_ratelimited
and remove the LIMIT_NETDEBUG macro.
All messages are still ratelimited.
Some KERN_<LEVEL> uses are changed to KERN_DEBUG.
This may have some negative impact on messages that were
emitted at KERN_INFO that are not not enabled at all unless
DEBUG is defined or dynamic_debug is enabled. Even so,
these messages are now _not_ emitted by default.
This also eliminates the use of the net_msg_warn sysctl
"/proc/sys/net/core/warnings". For backward compatibility,
the sysctl is not removed, but it has no function. The extern
declaration of net_msg_warn is removed from sock.h and made
static in net/core/sysctl_net_core.c
Miscellanea:
o Update the sysctl documentation
o Remove the embedded uses of pr_fmt
o Coalesce format fragments
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC name table updates are distributed asynchronously in a cluster,
entailing a risk of certain race conditions. E.g., if two nodes
simultaneously issue conflicting (overlapping) publications, this may
not be detected until both publications have reached a third node, in
which case one of the publications will be silently dropped on that
node. Hence, we end up with an inconsistent name table.
In most cases this conflict is just a temporary race, e.g., one
node is issuing a publication under the assumption that a previous,
conflicting, publication has already been withdrawn by the other node.
However, because of the (rtt related) distributed update delay, this
may not yet hold true on all nodes. The symptom of this failure is a
syslog message: "tipc: Cannot publish {%u,%u,%u}, overlap error".
In this commit we add a resiliency queue at the receiving end of
the name table distributor. When insertion of an arriving publication
fails, we retain it in this queue for a short amount of time, assuming
that another update will arrive very soon and clear the conflict. If so
happens, we insert the publication, otherwise we drop it.
The (configurable) retention value defaults to 2000 ms. Knowing from
experience that the situation described above is extremely rare, there
is no risk that the queue will accumulate any large number of items.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the pfifo_fast queue discipline has been used by default
for all devices. But we have better choices now.
This patch allow setting the default queueing discipline with sysctl.
This allows easy use of better queueing disciplines on all devices
without having to use tc qdisc scripts. It is intended to allow
an easy path for distributions to make fq_codel or sfq the default
qdisc.
This patch also makes pfifo_fast more of a first class qdisc, since
it is now possible to manually override the default and explicitly
use pfifo_fast. The behavior for systems who do not use the sysctl
is unchanged, they still get pfifo_fast
Also removes leftover random # in sysctl net core.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename LL_SO to BUSY_POLL_SO
Rename sysctl_net_ll_{read,poll} to sysctl_busy_{read,poll}
Fix up users of these variables.
Fix documentation for sysctl.
a patch for the socket.7 man page will follow separately,
because of limitations of my mail setup.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Rename functions in include/net/ll_poll.h to busy wait.
Clarify documentation about expected power use increase.
Rename POLL_LL to POLL_BUSY_LOOP.
Add need_resched() testing to poll/select busy loops.
Note, that in select and poll can_busy_poll is dynamic and is
updated continuously to reflect the existence of supported
sockets with valid queue information.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
select/poll busy-poll support.
Split sysctl value into two separate ones, one for read and one for poll.
updated Documentation/sysctl/net.txt
Add a new poll flag POLL_LL. When this flag is set, sock_poll will call
sk_poll_ll if possible. sock_poll sets this flag in its return value
to indicate to select/poll when a socket that can busy poll is found.
When poll/select have nothing to report, call the low-level
sock_poll again until we are out of time or we find something.
Once the system call finds something, it stops setting POLL_LL, so it can
return the result to the user ASAP.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This random old kernel version has no bearing on the actual
file contents, and has not had for a long time. Delete it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As per feedback from the netdev community, we change the buffer
overflow protection algorithm in receiving sockets so that it
always respects the nominal upper limit set in sk_rcvbuf.
Instead of scaling up from a small sk_rcvbuf value, which leads to
violation of the configured sk_rcvbuf limit, we now calculate the
weighted per-message limit by scaling down from a much bigger value,
still in the same field, according to the importance priority of the
received message.
To allow for administrative tunability of the socket receive buffer
size, we create a tipc_rmem sysctl variable to allow the user to
configure an even bigger value via sysctl command. It is a size of
three (min/default/max) to be consistent with things like tcp_rmem.
By default, the value initialized in tipc_rmem[1] is equal to the
receive socket size needed by a TIPC_CRITICAL_IMPORTANCE message.
This value is also set as the default value of sk_rcvbuf.
Originally-by: Jon Maloy <jon.maloy@ericsson.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
[Ying: added sysctl variation to Jon's original patch]
Signed-off-by: Ying Xue <ying.xue@windriver.com>
[PG: don't compile sysctl.c if not config'd; add Documentation]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an ndo_ll_poll method and the code that supports it.
This method can be used by low latency applications to busy-poll
Ethernet device queues directly from the socket code.
sysctl_net_ll_poll controls how many microseconds to poll.
Default is zero (disabled).
Individual protocol support will be added by subsequent patches.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes mentioning the sysfsf net_device weight attribute
(class/net/<device>/weight)
in Documentation/sysctl/net.txt, since the net sysfs weight attribute
was removed by the following patch:
[NET]: Make NAPI polling independent of struct net_device objects
bea3348eef
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All parameter descriptions in /proc/sys/net/core/* now is separated
two places. So, merge them into Documentation/sysctl/net.txt.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With RPS inclusion, skb timestamping is not consistent in RX path.
If netif_receive_skb() is used, its deferred after RPS dispatch.
If netif_rx() is used, its done before RPS dispatch.
This can give strange tcpdump timestamps results.
I think timestamping should be done as soon as possible in the receive
path, to get meaningful values (ie timestamps taken at the time packet
was delivered by NIC driver to our stack), even if NAPI already can
defer timestamping a bit (RPS can help to reduce the gap)
Tom Herbert prefer to sample timestamps after RPS dispatch. In case
sampling is expensive (HPET/acpi_pm on x86), this makes sense.
Let admins switch from one mode to another, using a new
sysctl, /proc/sys/net/core/netdev_tstamp_prequeue
Its default value (1), means timestamps are taken as soon as possible,
before backlog queueing, giving accurate timestamps.
Setting a 0 value permits to sample timestamps when processing backlog,
after RPS dispatch, to lower the load of the pre-RPS cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous description about system parameter in /proc/sys/net/unix/ is
wrong (or missed). Simply add a new description about unix_dgram_qlen
according to latest kernel.
Signed-off-by: Li Xiaodong <lixd@cn.fujitsu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now /proc/sys is described in many places and much information is
redundant. This patch updates the proc.txt and move the /proc/sys
desciption out to the files in Documentation/sysctls.
Details are:
merge
- 2.1 /proc/sys/fs - File system data
- 2.11 /proc/sys/fs/mqueue - POSIX message queues filesystem
- 2.17 /proc/sys/fs/epoll - Configuration options for the epoll interface
with Documentation/sysctls/fs.txt.
remove
- 2.2 /proc/sys/fs/binfmt_misc - Miscellaneous binary formats
since it's not better then the Documentation/binfmt_misc.txt.
merge
- 2.3 /proc/sys/kernel - general kernel parameters
with Documentation/sysctls/kernel.txt
remove
- 2.5 /proc/sys/dev - Device specific parameters
since it's obsolete the sysfs is used now.
remove
- 2.6 /proc/sys/sunrpc - Remote procedure calls
since it's not better then the Documentation/sysctls/sunrpc.txt
move
- 2.7 /proc/sys/net - Networking stuff
- 2.9 Appletalk
- 2.10 IPX
to newly created Documentation/sysctls/net.txt.
remove
- 2.8 /proc/sys/net/ipv4 - IPV4 settings
since it's not better then the Documentation/networking/ip-sysctl.txt.
add
- Chapter 3 Per-Process Parameters
to descibe /proc/<pid>/xxx parameters.
Signed-off-by: Shen Feng <shen@cn.fujitsu.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
