The STM45PE20 pinstrap on 5762 devices supports multiple sizes. So treat
it just like the ST45_USPT and the size will be read from 0xf0 via
tg3_get_nvram_size().
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tg3_setup_copper_phy(), if autonegotiation is disabled, we need to
relink only if the speed or duplex does not match the configured
setting. If flow control does not match, a relink is not necessary as
flow control is not a PHY setting. Later on, we'll call
tg3_setup_flow_ctrl() to set up the MAC to the desired flow control
settings if we're in full duplex mode.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces an UAPI header for the SCTP protocol,
so that we can facilitate the maintenance and development of
user land applications or libraries, in particular in terms
of header synchronization.
To not break compatibility, some fragments from lksctp-tools'
netinet/sctp.h have been carefully included, while taking care
that neither kernel nor user land breaks, so both compile fine
with this change (for lksctp-tools I tested with the old
netinet/sctp.h header and with a newly adapted one that includes
the uapi sctp header). lksctp-tools smoke test run through
successfully as well in both cases.
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_spi_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callers always pass current to sock_update_netprio().
Signed-off-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callers always pass current to sock_update_classid().
Signed-off-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of invalidating all IPv6 addresses with global scope
when one decides to use IPv6 tokens, we should only invalidate
previous tokens and leave the rest intact until they expire
eventually (or are intact forever). For doing this less greedy
approach, we're adding a bool at the end of inet6_ifaddr structure
instead, for two reasons: i) per-inet6_ifaddr flag space is
already used up, making it wider might not be a good idea,
since ii) also we do not necessarily need to export this
information into user space.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we set the iftoken in inet6_set_iftoken(), we return -EINVAL
when the device does not have flag IF_READY. This is however not
necessary and rather an artificial usability barrier, since we
simply can set the token despite that, and in case the device is
ready, we just send out our rs, otherwise ifup et al. will do
this for us anyway.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we check for !ipv6_addr_any(&in6_dev->token) in
addrconf_prefix_rcv(), make the token initialization on
device setup more intuitive by using in6addr_any as an
initializer.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receiving unhandled notifications is most certainly not an error
and should not be logged as one. Knowing that the device sends
notifications we don't handle is useful for developers, but there
is very little a user can do about this. The message is therefore
just annoying noise to most users with devices sending unhandled
notifications like e.g. USB_CDC_NOTIFY_RESPONSE_AVAILABLE
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new file, Documentation/cgroups/net_cls.txt, with info
about net_cls cgroups, and updates the 00-INDEX accordingly.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for IPv6 tokenized IIDs, that allow
for administrators to assign well-known host-part addresses
to nodes whilst still obtaining global network prefix from
Router Advertisements. It is currently in draft status.
The primary target for such support is server platforms
where addresses are usually manually configured, rather
than using DHCPv6 or SLAAC. By using tokenised identifiers,
hosts can still determine their network prefix by use of
SLAAC, but more readily be automatically renumbered should
their network prefix change. [...]
The disadvantage with static addresses is that they are
likely to require manual editing should the network prefix
in use change. If instead there were a method to only
manually configure the static identifier part of the IPv6
address, then the address could be automatically updated
when a new prefix was introduced, as described in [RFC4192]
for example. In such cases a DNS server might be
configured with such a tokenised interface identifier of
::53, and SLAAC would use the token in constructing the
interface address, using the advertised prefix. [...]
http://tools.ietf.org/html/draft-chown-6man-tokenised-ipv6-identifiers-02
The implementation is partially based on top of Mark K.
Thompson's proof of concept. However, it uses the Netlink
interface for configuration resp. data retrival, so that
it can be easily extended in future. Successfully tested
by myself.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to prefetch, in the stmmac_rx, the whole
dma_erx descriptor in case of using the extended descriptors.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
recently many new supports have been added in the stmmac driver w/o taking care
about where each new field had to be placed inside the private structure for
guaranteeing the best cache usage.
This is what I wanted in the beginning, so this patch reorganizes all the fields
in order to keep adjacent fields for cache effect.
I have also tried to optimize them by using pahole.
V2: do not abuse with ____cacheline_aligned_in_smp and keep fields that
potentially could stay in the same cache-line for better usage in SMP systems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidies up the code. I have run Linden (and verified with checkpatch)
many part of the driver trying to reorganize some sections respecting the
codying-style rules in the points where it was not done.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch reviews/improves and adds some fixes in the code doc.
Also kernel-doc passes w/o any warnings.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reviews the driver documentation file;
for example, there were some new fields (in the driver
module parameter section) and the ptp files were
not documented.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the pcs mode support for SGMII. Even though
SGMII does auto-negotiation with phy, it needs stmmac_init_phy and
stmmac_mdio_register function for initializing phy.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using DT for mdiobus and ethernet-phy requires to know the PHY address, which
is hard to guess if you don't know it. This patch extends of_mdiobus_register
to scan mdiobus for PHYs if reg property of the corresponding node is not set.
This also allows to have phy nodes in SoC DT files where the reg property can
be overwritten in the board file later. To encourage people to finally set the
actual phy address, the mdiobus scan is noisier than required.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell mdio driver uses internal registers that can be clock gated on
some SoCs. This patch just adds optional clock handling, to allow to pass
and enable the corresponding clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using module_spi_driver we can eliminate a few lines of boilerplate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two sections checked whether the current channel != the new channel
without ever setting the current channel variables.
1. net/mac802154/tx.c: Prevent set_channel() from getting called every
time a packet is sent.
2. net/mac802154/mib.c: Lock (pib_lock) accesses to current_channel and
current_page and make sure they are updated when the channel has been
changed.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the MRF24J40, link-layer acknowledgment request and retry must be
turned on explicitly for each packet. Turn this on in the hardware based
on the FC_ACK_REQ bit being set in the packet.
Also, now that failure to receive an ACK will cause the hardware to report
failure of transmission, change the log level for this failure to debug
level.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi Greg,
I'm unsure if you or Dave should take that one as it's for one a TTY
patch but also living under net/. So I'm uncertain and let you decide!
Thanks,
Mathias
-- >8 --
Subject: [PATCH] TTY: ircomm, use GFP_KERNEL in ircomm_open()
We're clearly running in non-atomic context as our only call site is
able to call wait_event_interruptible(). So we're safe to use GFP_KERNEL
here instead of GFP_ATOMIC.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only call site of irda_connect_response() is irda_accept() -- a
function called from user context only. Therefore it has no need for
GFP_ATOMIC.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irda_create() is called from user context only, therefore has no need
for GFP_ATOMIC.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull() can change skb->head, so we must init iph/greh after
calling it.
Bug added in commit c544193214 (GRE: Refactor GRE tunneling code.)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In at86rf230_probe() lp was first set to dev->priv and a few lines later
dev->priv was set to lp again, without changing lp in between. The call
to ieee802154_unregister_device() before err_irq: was unreachable.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a feature is not supported by firmware no need to print an error message.
This surpresses the following harmless message on boot up and ethtool query.
enic: Error 1 devcmd 36
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for NULL before calling the following operations from "struct
ieee802154_mlme_ops": assoc_req, assoc_resp, disassoc_req, start_req,
and scan_req.
This fixes a current oops where those functions are called but not
implemented. It also updates the documentation to clarify that they
are now optional by design. If a call to an unimplemented function
is attempted, the kernel returns EOPNOTSUPP via netlink.
The following operations are still required: get_phy, get_pan_id,
get_short_addr, and get_dsn.
Note that the places where this patch changes the initialization
of "ret" should not affect the rest of the code since "ret" was
always set (again) before returning its value.
Signed-off-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It served no purpose: we never call it from anywhere in the stack
and the only driver that did implement it (fakehard) merely provided
a dummy value.
There is also considerable doubt whether it would make sense to
even attempt beacon processing at this level in the Linux kernel.
Signed-off-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that uids and gids are completely encapsulated in kuid_t
and kgid_t we no longer need to pass struct cred which allowed
us to test both the uid and the user namespace for equality.
Passing struct cred potentially allows us to pass the entire group
list as BSD does but I don't believe the cost of cache line misses
justifies retaining code for a future potential application.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check KR2 recovery time at the beginning of the work-around function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Octeon SMI/MDIO interfaces can do clause 45 communications, so
implement this in the driver.
Also fix some comment formatting to make it consistent and to comply
with the netdev style.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_queue_xmit() will return a positive value if the packet could not be
queued, often because the real network device (in our case the mac802154
wpan device) has its queue stopped. lowpan_xmit() should handle the
positive return code (for the debug statement) and return that value to
the higher layer so the higher layer will retry sending the packet.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the buffer length from 10 to 300 packets. Consider that traffic on
mac802154 devices will often be 6LoWPAN, and a full-length (1280 octet)
IPv6 packet will fragment into 15 6LoWPAN fragments (because the MTU of
IEEE 802.15.4 is 127). A 300-packet queue is really 20 full-length IPv6
packets.
With a queue length of 10, an entire IPv6 packet was unable to get queued
at one time, causing fragments to be dropped, and making reassembly
impossible.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_stop_queue() and netif_wake_queue() to control the flow of
packets to mac802154 devices. Since many IEEE 802.15.4 devices have no
output buffer, and since the mac802154 xmit() function is designed to
block, netif_stop_queue() is called after each packet.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ops->xmit() fails, drop the packet. Devices which support hardware
ack and retry (which include all devices currently supported by mainline),
will automatically retry sending the packet (in the hardware) up to 3
times, per the 802.15.4 spec. There is no need, and it is incorrect to
try to do it in mac802154.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(Resend with a better changelog)
garp_pdu_queue() should ways be called with this spin lock.
garp_uninit_applicant() only holds rtnl lock which is not
enough here. A possible race can happen as garp_pdu_rcv()
is called in BH context:
garp_pdu_rcv()
|->garp_pdu_parse_msg()
|->garp_pdu_parse_attr()
|-> garp_gid_event()
Found by code inspection.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Ward <david.ward@ll.mit.edu>
Cc: "Jorge Boncompte [DTI2]" <jorge@dti2.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a simple test case that probes the packet socket's
TPACKET_V1, TPACKET_V2 and TPACKET_V3 behavior regarding mmap(2)'ed
I/O for a small burst of 100 packets. The test currently runs for ...
TPACKET_V1: RX_RING, TX_RING
TPACKET_V2: RX_RING, TX_RING
TPACKET_V3: RX_RING
... and will output on success:
test: TPACKET_V1 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
test: TPACKET_V1 with PACKET_TX_RING .................... 100 pkts (9600 bytes)
test: TPACKET_V2 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
test: TPACKET_V2 with PACKET_TX_RING .................... 100 pkts (9600 bytes)
test: TPACKET_V3 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
OK. All tests passed
Reusable parts of psock_fanout.c have been put into a psock_lib.h
file for common usage. Test case successfully tested on x86_64.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch bypasses vxlan encapsulation if the destination vxlan
endpoint is a local device.
Changes since v1: added missing check for vxlan_find_vni() failure
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When our getdcbx entry is called, DCB_CAP_DCBX_HOST should be advertized too.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the DCB ETS ops only when supported by the firmware. For older firmware/cards
which don't support ETS, advertize only PFC DCB ops.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
