The initial idea of the Colorspace prop was that this maps 1:1 to
InfoFrames/SDP but KMS does not give user space enough information nor
control over the output format to figure out which variants can be used
for a given KMS commit. At the same time, properties like Broadcast RGB
expect full range quantization range being produced by user space from
the CRTC and drivers to convert to the range expected by the sink for
the chosen output format, mode, InfoFrames, etc.
This change documents the reality of the Colorspace property. The
Default variant unfortunately is very much driver specific and not
reflected by the EDID. The BT2020 variants are in active use by generic
compositors which have expectations from the driver about the
conversions it has to do when selecting certain output formats.
Everything else is also marked as undefined. Coming up with valid
behavior that makes it usable from user space and consistent with other
KMS properties for those variants is left as an exercise for whoever
wants to use them.
v2:
* Talk about "pixel operation properties" that user space configures
* Mention that user space is responsible for checking the EDID for sink
support
* Make it clear that drivers can choose between RGB and YCbCr on their
own
Signed-off-by: Sebastian Wick <sebastian.wick@redhat.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240702143017.2429975-1-sebastian.wick@redhat.com
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240612152336.v2.3.Ifb4450979b62976fd5a98847dade2e5b377d47c8@changeid
While working on rvkms, I noticed that there's no code that actually uses
the drm_pending_vblank_event that's embedded in vkms_output. So, just drop
the member from the struct.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Tested-by: Louis Chauvet <louis.chauvet@bootlin.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240703160458.1303872-1-lyude@redhat.com
Core in platform_driver_register() already sets the .owner, so driver
does not need to. Whatever is set here will be anyway overwritten by
main driver calling platform_driver_register().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240330205722.93801-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Core in platform_driver_register() already sets the .owner, so driver
does not need to. Whatever is set here will be anyway overwritten by
main driver calling platform_driver_register().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240330205722.93801-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Core in platform_driver_register() already sets the .owner, so driver
does not need to. Whatever is set here will be anyway overwritten by
main driver calling platform_driver_register().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240330203831.87003-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Core in platform_driver_register() already sets the .owner, so driver
does not need to. Whatever is set here will be anyway overwritten by
main driver calling platform_driver_register().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240330203831.87003-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Core in platform_driver_register() already sets the .owner, so driver
does not need to. Whatever is set here will be anyway overwritten by
main driver calling platform_driver_register().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240330203831.87003-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Core in platform_driver_register() already sets the .owner, so driver
does not need to. Whatever is set here will be anyway overwritten by
main driver calling platform_driver_register().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240330203831.87003-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
If a queue is already assigned to the hardware, then a newly submitted
job can start straight away without waiting for the tick. However in
this case the devfreq infrastructure isn't notified that the GPU is
busy. By the time the tick happens the job might well have finished and
no time will be accounted for the GPU being busy.
Fix this by recording the GPU as busy directly in queue_run_job() in the
case where there is a CSG assigned and therefore we just ring the
doorbell.
Fixes: de85488138 ("drm/panthor: Add the scheduler logical block")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240703155646.80928-1-steven.price@arm.com
Add a helper to dump the Display Stream Compression configuration, taken
into use in the i915 driver by a later patch.
v2:
- Rebase on the s/DRM_X16/FXP_Q4 change.
- s/DSC configration/DSC configuration in the function documentation.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240628164451.1177612-3-imre.deak@intel.com
Add helpers to convert between q4 fixed point and integer/fraction
values. Also add the format/argument macros required to printk q4 fixed
point variables. The q4 notation is based on the short variant described
by
https://en.wikipedia.org/wiki/Q_(number_format)
where only the number of fraction bits in the fixed point value are
defined, while the full size is deducted from the container type, that
is the size of int for these helpers. Using the fxp_ prefix, which makes
moving these helpers outside of drm to a more generic place easier, if
they prove to be useful.
These are needed by later patches dumping the Display Stream Compression
configuration in DRM core and in the i915 driver to replace the
corresponding bpp_x16 helpers defined locally in the driver.
v2: Use the more generic/descriptive fxp_q4 prefix instead of drm_x16.
(Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240628164451.1177612-2-imre.deak@intel.com
[Why]
During resume, observe that we receive CSN event before we start topology
probing. Handling CSN at this moment based on uncertain topology is
unnecessary.
[How]
Add checking condition in drm_dp_mst_handle_up_req() to skip handling CSN
if the topology is yet to be probed.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240626084825.878565-3-Wayne.Lin@amd.com
[Why]
After supend/resume, with topology unchanged, observe that
link_address_sent of all mstb are marked as false even the topology probing
is done without any error.
It is caused by wrongly also include "ret == 0" case as a probing failure
case.
[How]
Remove inappropriate checking conditions.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org
Fixes: 37dfdc55ff ("drm/dp_mst: Cleanup drm_dp_send_link_address() a bit")
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240626084825.878565-2-Wayne.Lin@amd.com
Panfrost DRM driver uses devfreq to perform DVFS, while using simple_ondemand
devfreq governor by default. This causes driver initialization to fail on
boot when simple_ondemand governor isn't built into the kernel statically,
as a result of the missing module dependency and, consequently, the required
governor module not being included in the initial ramdisk. Thus, let's mark
simple_ondemand governor as a softdep for Panfrost, to have its kernel module
included in the initial ramdisk.
This is a rather longstanding issue that has forced distributions to build
devfreq governors statically into their kernels, [1][2] or has forced users
to introduce some unnecessary workarounds. [3]
For future reference, not having support for the simple_ondemand governor in
the initial ramdisk produces errors in the kernel log similar to these below,
which were taken from a Pine64 RockPro64:
panfrost ff9a0000.gpu: [drm:panfrost_devfreq_init [panfrost]] *ERROR* Couldn't initialize GPU devfreq
panfrost ff9a0000.gpu: Fatal error during GPU init
panfrost: probe of ff9a0000.gpu failed with error -22
Having simple_ondemand marked as a softdep for Panfrost may not resolve this
issue for all Linux distributions. In particular, it will remain unresolved
for the distributions whose utilities for the initial ramdisk generation do
not handle the available softdep information [4] properly yet. However, some
Linux distributions already handle softdeps properly while generating their
initial ramdisks, [5] and this is a prerequisite step in the right direction
for the distributions that don't handle them properly yet.
[1] https://gitlab.manjaro.org/manjaro-arm/packages/core/linux/-/blob/linux61/config?ref_type=heads#L8180
[2] https://salsa.debian.org/kernel-team/linux/-/merge_requests/1066
[3] https://forum.pine64.org/showthread.php?tid=15458
[4] https://git.kernel.org/pub/scm/utils/kernel/kmod/kmod.git/commit/?id=49d8e0b59052999de577ab732b719cfbeb89504d
[5] 97ac4d37aa
Cc: Diederik de Haas <didi.debian@cknow.org>
Cc: Furkan Kardame <f.kardame@manjaro.org>
Cc: stable@vger.kernel.org
Fixes: f3ba91228e ("drm/panfrost: Add initial panfrost driver")
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4e1e00422a14db4e2a80870afb704405da16fd1b.1718655077.git.dsimic@manjaro.org
The if condition !A || A && B can be simplified to !A || B.
Fixes the following Coccinelle/coccicheck warning reported by
excluded_middle.cocci:
WARNING !A || A && B is equivalent to !A || B
Compile-tested only.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240701195607.228852-1-thorsten.blum@toblux.com
Ast has no special requirements for runtime power management. So
replace drm_atomic_helper_commit_tail_rpm() with the regular helper
drm_atomic_helper_commit_tail().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-9-tzimmermann@suse.de
The function ast_crtc_dpms() is left over from when the ast driver
did not implement atomic modesetting. But DPMS is not supported by
atomic modesetting and the helper is only called to enable or
disable the CRTC sync pulses. Inline the function into its callers.
To disable the CRTC, ast sets (AST_DPMS_VSYNC_OFF | AST_DPMS_HSYNC_OFF)
in VGACRB6. Replace the constants with the correct register constants
for VGACRB6.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-8-tzimmermann@suse.de
The SCREEN_DISABLE bit controls scanout from display memory. The bit
affects all planes, so set it only in the CRTC's atomic enable and
disable functions.
A number of bugs affect this fix. First of all, ast_set_std_regs()
tries to set VGASR1 except for the SD bit. But the read bitmask is
invert, so it preserves anything except the SD bit. Fix this by
re-inverting the read mask.
The second issue is that primary-plane and CRTC helpers modify the
SD bit. The bit controls scanout for all planes, primary and HW
cursor, so set it only in the CRTC code.
Further add a constant to represent the SD bit in VGASR1. Keep the
plane's atomic_disable around to make the DRM framework happy.
v2:
- fix typos in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-7-tzimmermann@suse.de
The DPMS code, called from the CRTC's atomic_enable, rewrites the
gamma LUT. This is already done by the CRTC's atomic_flush. Remove
the duplication.
v2:
- fix a typo in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-6-tzimmermann@suse.de
Several color registers are programmed in the DPMS code of the CRTC's
atomic_enable helper and the primary plane's atomic_update. It requires
the color format and the display mode.
Both code paths handle different cases: the DPMS's code will not be
executed if the color format changes without a full mode switch. The
plane's code only runs if the color format changes, but ignores
display-mode changes.
The color format is a property of the primary plane, so consolidate all
color-format code in the plane's atomic_update. Remove it from the DPMS
helper.
v2:
- clarify commit message (Jocelyn)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-5-tzimmermann@suse.de
Do all mode setting in ast_crtc_helper_mode_set_nofb(), which
always runs after disabling the CRTC and before programming the
planes. Removes implicit synchronization between the CRTC's
atomic disable, enable and the vertical retrace.
Display-mode updates require HW cursors to be disabled. The HW
cursor only picks up changes at vertical retrace periods. So the
CRTC's atomic_disable helper waited for the retrace to delay any
following mode-setting operations, which then happened in
atomic_enable. See [1] for a description of the problem.
With the CRTC helper callback mode_set_nofb, we can now synchronize
and reprogram in the same place. As it always runs before the plane
update, the plane code can be reordered with the CRTC's later
atomic_enable et al.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/series/79914/ # 1
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-4-tzimmermann@suse.de
The CRTC's atomic_flush function contains code to program the
display mode to the AST DP chip. Move the code to the encoder's
atomic_mode_set callback. The DRM atomic-modesetting code invoke
this callback as part of the atomic commit.
v2:
- fix typos in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-3-tzimmermann@suse.de
The CRTC helpers contain code to enable and disable DisplayPort
connectors. Implement this functionality in the respective connector's
atomic_enable/atomic_disable callbacks. DRM's atomic-modesetting
helpers will call the functions as part of the atomic commit.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-2-tzimmermann@suse.de
Lima DRM driver uses devfreq to perform DVFS, while using simple_ondemand
devfreq governor by default. This causes driver initialization to fail on
boot when simple_ondemand governor isn't built into the kernel statically,
as a result of the missing module dependency and, consequently, the
required governor module not being included in the initial ramdisk. Thus,
let's mark simple_ondemand governor as a softdep for Lima, to have its
kernel module included in the initial ramdisk.
This is a rather longstanding issue that has forced distributions to build
devfreq governors statically into their kernels, [1][2] or may have forced
some users to introduce unnecessary workarounds.
Having simple_ondemand marked as a softdep for Lima may not resolve this
issue for all Linux distributions. In particular, it will remain
unresolved for the distributions whose utilities for the initial ramdisk
generation do not handle the available softdep information [3] properly
yet. However, some Linux distributions already handle softdeps properly
while generating their initial ramdisks, [4] and this is a prerequisite
step in the right direction for the distributions that don't handle them
properly yet.
[1] https://gitlab.manjaro.org/manjaro-arm/packages/core/linux-pinephone/-/blob/6.7-megi/config?ref_type=heads#L5749
[2] 7f64e287e7/main/linux-postmarketos-allwinner/config-postmarketos-allwinner.aarch64 (L4654)
[3] https://git.kernel.org/pub/scm/utils/kernel/kmod/kmod.git/commit/?id=49d8e0b59052999de577ab732b719cfbeb89504d
[4] 97ac4d37aa
Cc: Philip Muller <philm@manjaro.org>
Cc: Oliver Smith <ollieparanoid@postmarketos.org>
Cc: Daniel Smith <danct12@disroot.org>
Cc: stable@vger.kernel.org
Fixes: 1996970773 ("drm/lima: Add optional devfreq and cooling device support")
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fdaf2e41bb6a0c5118ff9cc21f4f62583208d885.1718655070.git.dsimic@manjaro.org
DSISRC __________
__\_
| \
pll4_p_ck ->| 1 |____dsi_k
ck_dsi_phy ->| 0 |
|____/
A DSI clock is missing in the clock framework. Looking at the
clk_summary, it appears that 'ck_dsi_phy' is not implemented. Since the
DSI kernel clock is based on the internal DSI pll. The common clock
driver can not directly expose this 'ck_dsi_phy' clock because it does
not contain any common registers with the DSI. Thus it needs to be done
directly within the DSI phy driver.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240129104106.43141-4-raphael.gallais-pou@foss.st.com
Update control of clocks and supply thanks to the PM runtime
mechanism to avoid kernel crash during a system suspend.
Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240129104106.43141-3-raphael.gallais-pou@foss.st.com
Use RUNTIME_PM_OPS() instead of the old SET_SYSTEM_SLEEP_PM_OPS().
This means we don't need __maybe_unused on the functions.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240129104106.43141-2-raphael.gallais-pou@foss.st.com
The Low-Voltage Differential Signaling (LVDS) Display Interface
Transmitter handles the LVDS protocol: it maps the pixels received from
the upstream Pixel-DMA LCD-TFT Display Controller (LTDC) onto the LVDS
PHY.
It is composed of three sub blocks:
* LVDS host: handles the LVDS protocol (FPD / OpenLDI) and maps
its input pixels onto the data lanes of the PHY
* LVDS PHY: parallelize the data and drives the LVDS data lanes
* LVDS wrapper: handles top-level settings
The LVDS controller driver supports the following high-level features:
* FDP-Link-I and OpenLDI (v0.95) protocols
* Single-Link or Dual-Link operation
* Single-Display or Double-Display (with the same content
duplicated on both)
* Flexible Bit-Mapping, including JEIDA and VESA
* RGB888 or RGB666 output
* Synchronous design, with one input pixel per clock cycle
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226-lvds-v6-2-15e3463fbe70@foss.st.com
Currently, the init_code of the jd9365da driver is placed
in the enable() function and sent, but this seems to take
a long time. It takes 17ms to send each instruction (an init
code consists of about 200 instructions), so it takes
about 3.5s to send the init_code. So we moved the sending
of the inti_code to the prepare() function, and each
instruction seemed to take only 25μs.
We checked the DSI host and found that the difference in
command sending time is caused by the different modes of
the DSI host in prepare() and enable() functions.
Our DSI Host only supports sending cmd in LP mode, The
prepare() function can directly send init_code (LP->cmd)
in LP mode, but the enable() function is in HS mode and
needs to switch to LP mode before sending init code
(HS->LP->cmd->HS). Therefore, it takes longer to send
the command.
Signed-off-by: Zhaoxiong Lv <lvzhaoxiong@huaqin.corp-partner.google.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240624141926.5250-2-lvzhaoxiong@huaqin.corp-partner.google.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240624141926.5250-2-lvzhaoxiong@huaqin.corp-partner.google.com
Timeouts on the AUX bus are to be expected in certain normal operating
conditions. There is no need to raise an error log or re-initialize the
whole AUX state machine. Simply acknowledge the AUX_ERR interrupt and
let upper layers know about the timeout.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-14-l.stach@pengutronix.de
All AUX error responses raise the AUX_ERR interrupt, so there is no
need to read the AUX status register in normal operation. Only read
the status when an error occurred and we can expect a different
status than OK.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-13-l.stach@pengutronix.de
Move the wait loop into its own function, so it doesn't need to be
replicated in multiple locations. Also move the PLL lock checks between
setting the link bandwidth, which may cause the PLL to unlock, and the
MACRO_RST which needs the PLL to be locked.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-12-l.stach@pengutronix.de
The PLL will be reconfigured later, which may cause it to go out of lock
anyway, so there is no point in waiting for the PLL to lock here. Instead
we can continue execution of the link setup, which will properly set the
PLL parameters and will wait for the PLL to lock at the appropriate times.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-11-l.stach@pengutronix.de
Setting the link bandwidth may change the PLL parameters, which will cause
the PLL to go out of lock, so make sure to apply the MACRO_RST, which
according to the comment is required to be pulsed after the PLL is locked.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-10-l.stach@pengutronix.de
This check is way too late in the DP enable flow. The PLL must be
locked much earlier, before any link training can happen. If the
PLL is unlocked at that point in time there is something seriously
wrong in the enable flow.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Robet Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-9-l.stach@pengutronix.de
Make sure the controller is in a basic working state after runtime
resume. Keep the analog function enable in the mode set path as this
enables parts of the PHY that are only required to be powered when
there is a data stream being sent out.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-8-l.stach@pengutronix.de
Platform and PHY power isn't only required when the actual display data
stream is active, but may be required earlier to support AUX channel
transactions. Move them into the runtime PM calls, so they are properly
managed whenever various other parts of the driver need them to be active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-7-l.stach@pengutronix.de
The clock is already managed by runtime PM, which is properly invoked
from the analogix_dp_set_bridge function, so there is no need for an
additional reference.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-6-l.stach@pengutronix.de
