Instead of returning -EOPNOTSUPP when a slave device has no PHY,
directly return -ENODEV as ethtool and phylib do.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Add router adjacency dpipe table
Arkadi says:
This patchset adds router adjacency dpipe table support. This will provide
the ability to observe the hardware offloaded IPv4/6 nexthops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for controlling nexthop counters via dpipe.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for adjacency table dump.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting counters on nexthops based on dpipe's adjacency
table counter status. This patch also adds the ability for getting the
counter value, which will be used by the dpipe adjacency table dump
implementation in the next patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to add the ability for setting counters on nexthops the RATR
register should be extended.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial support for router adjacency table. The table does lookup
based on the nexthop-group index and the local nexthop offset. After
locating the nexthop entry it sets the destination MAC address and the
egress RIF.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before introducing the ability to dump the
adjacency table via dpipe, and to count the table size. The current table
implementation avoids tunnel entries, thus a helper for checking if
the nexthop group contains tunnel entries is also provided. The mlxsw's
nexthop representative struct stays private to the router module.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use list_is_last helper to check for last neighbor.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep nexthops in a linked list for easy access.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds field for mlxsw's meta header which will be used to
describe the match/action behavior of the adjacency table.
The fields are:
1. Adj_index - The global index of the nexthop group in the adjacency
table.
2. Adj_hash_index - Local index offset which is based on packets hash
mod the nexthop group size.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix indentation in mlxsw_meta header's description.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
BPF metadata for direct access
This work enables generic transfer of metadata from XDP into skb,
meaning the packet has a flexible and programmable room for meta
data, which can later be used by BPF to set various skb members
when passing up the stack. For details, please see second patch.
Support has been implemented and tested with two drivers, and
should be straight forward to add to other drivers as well which
properly support head adjustment already.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for transferring XDP meta data into skb for
ixgbe driver; before calling into the program, xdp.data_meta points
to xdp.data, where on program return with pass verdict, we call
into skb_metadata_set().
We implement this for the default ixgbe_build_skb() variant. For the
ixgbe_construct_skb() that is used when legacy-rx buffer mananagement
mode is turned on via ethtool, I found that XDP gets 0 headroom, so
neither xdp_adjust_head() nor xdp_adjust_meta() can be used with this.
Just add a comment with explanation for this operating mode.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for transferring XDP meta data into skb for
nfp driver; before calling into the program, xdp.data_meta points
to xdp.data, where on program return with pass verdict, we call
into skb_metadata_set().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add various test_verifier selftests, and a simple xdp/tc functional
test that is being attached to veths. Also let new versions of clang
use the recently added -mcpu=probe support [1] for the BPF target,
so that it can probe the underlying kernel for BPF insn set extensions.
We could also just set this options always, where older versions just
ignore it and give a note to the user that the -mcpu value is not
supported, but given emitting the note cannot be turned off from clang
side lets not confuse users running selftests with it, thus fallback
to the default generic one when we see that clang doesn't support it.
Also allow CPU option to be overridden in the Makefile from command
line.
[1] d7276a40d8
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like a couple of updates missed to get carried into tools/include/uapi/,
so copy the bpf.h header as usual to pull in latest updates.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work enables generic transfer of metadata from XDP into skb. The
basic idea is that we can make use of the fact that the resulting skb
must be linear and already comes with a larger headroom for supporting
bpf_xdp_adjust_head(), which mangles xdp->data. Here, we base our work
on a similar principle and introduce a small helper bpf_xdp_adjust_meta()
for adjusting a new pointer called xdp->data_meta. Thus, the packet has
a flexible and programmable room for meta data, followed by the actual
packet data. struct xdp_buff is therefore laid out that we first point
to data_hard_start, then data_meta directly prepended to data followed
by data_end marking the end of packet. bpf_xdp_adjust_head() takes into
account whether we have meta data already prepended and if so, memmove()s
this along with the given offset provided there's enough room.
xdp->data_meta is optional and programs are not required to use it. The
rationale is that when we process the packet in XDP (e.g. as DoS filter),
we can push further meta data along with it for the XDP_PASS case, and
give the guarantee that a clsact ingress BPF program on the same device
can pick this up for further post-processing. Since we work with skb
there, we can also set skb->mark, skb->priority or other skb meta data
out of BPF, thus having this scratch space generic and programmable
allows for more flexibility than defining a direct 1:1 transfer of
potentially new XDP members into skb (it's also more efficient as we
don't need to initialize/handle each of such new members). The facility
also works together with GRO aggregation. The scratch space at the head
of the packet can be multiple of 4 byte up to 32 byte large. Drivers not
yet supporting xdp->data_meta can simply be set up with xdp->data_meta
as xdp->data + 1 as bpf_xdp_adjust_meta() will detect this and bail out,
such that the subsequent match against xdp->data for later access is
guaranteed to fail.
The verifier treats xdp->data_meta/xdp->data the same way as we treat
xdp->data/xdp->data_end pointer comparisons. The requirement for doing
the compare against xdp->data is that it hasn't been modified from it's
original address we got from ctx access. It may have a range marking
already from prior successful xdp->data/xdp->data_end pointer comparisons
though.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just do the rename into bpf_compute_data_pointers() as we'll add
one more pointer here to recompute.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer and mod_timer API instead of structure assignments.
This is done using Coccinelle and semantic patch used
for this as follows:
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon says:
====================
qed: iWARP fixes and enhancements
This patch series includes several fixes and enhancements
related to iWARP.
Patch #1 is actually the last of the initial iWARP submission.
It has been delayed until now as I wanted to make sure that qedr
supports iWARP prior to enabling iWARP device detection.
iWARP changes in RDMA tree have been accepted and targeted at
kernel 4.15, therefore, all iWARP fixes for this cycle are
submitted to net-next.
Changes from v1->v2
- Added "Fixes:" tag to commit message of patch #3
====================
Signed-off by: Michal.Kalderon@cavium.com
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A SYN packet which arrives with errors from FW should be dropped.
This required adding an additional field to the ll2
rx completion data.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum number of CQs supported is bound to the number
of connections supported, which differs between RoCE and iWARP.
This fixes a crash that occurred in iWARP when running 1000 sessions
using perftest.
Fixes: 67b40dccc4 ("qed: Implement iWARP initialization, teardown and qp operations")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP requires OOO support which is already provided by the ll2
interface (until now was used only for iSCSI offload).
The changes mostly include opening a ll2 dedicated connection for
OOO and notifiying the FW about the handle id.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the last of the initial iWARP patch series. It
adds the possiblity to actually detect iWARP from the device and enable
it in the critical locations which basically make iWARP available.
It wasn't submitted until now as iWARP hadn't been accepted into
the rdma tree.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key length can't be negative.
Leave comparisons against nla_len() signed just in case truncated attribute
can sneak in there.
Space savings:
add/remove: 0/0 grow/shrink: 0/7 up/down: 0/-7 (-7)
function old new delta
pneigh_delete 273 272 -1
mlx5e_rep_netevent_event 1415 1414 -1
mlx5e_create_encap_header_ipv6 1194 1193 -1
mlx5e_create_encap_header_ipv4 1071 1070 -1
cxgb4_l2t_get 1104 1103 -1
__pneigh_lookup 69 68 -1
__neigh_create 2452 2451 -1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As measured in my prior patch ("sch_netem: faster rb tree removal"),
rbtree_postorder_for_each_entry_safe() is nice looking but much slower
than using rb_next() directly, except when tree is small enough
to fit in CPU caches (then the cost is the same)
Also note that there is not even an increase of text size :
$ size net/core/skbuff.o.before net/core/skbuff.o
text data bss dec hex filename
40711 1298 0 42009 a419 net/core/skbuff.o.before
40711 1298 0 42009 a419 net/core/skbuff.o
From: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running TCP tests involving netem storing millions of packets,
I had the idea to speed up tfifo_reset() and did experiments.
I tried the rbtree_postorder_for_each_entry_safe() method that is
used in skb_rbtree_purge() but discovered it was slower than the
current tfifo_reset() method.
I measured time taken to release skbs with three occupation levels :
10^4, 10^5 and 10^6 skbs with three methods :
1) (current 'naive' method)
while ((p = rb_first(&q->t_root))) {
struct sk_buff *skb = netem_rb_to_skb(p);
rb_erase(p, &q->t_root);
rtnl_kfree_skbs(skb, skb);
}
2) Use rb_next() instead of rb_first() in the loop :
p = rb_first(&q->t_root);
while (p) {
struct sk_buff *skb = netem_rb_to_skb(p);
p = rb_next(p);
rb_erase(&skb->rbnode, &q->t_root);
rtnl_kfree_skbs(skb, skb);
}
3) "optimized" method using rbtree_postorder_for_each_entry_safe()
struct sk_buff *skb, *next;
rbtree_postorder_for_each_entry_safe(skb, next,
&q->t_root, rbnode) {
rtnl_kfree_skbs(skb, skb);
}
q->t_root = RB_ROOT;
Results :
method_1:while (rb_first()) rb_erase() 10000 skbs in 690378 ns (69 ns per skb)
method_2:rb_first; while (p) { p = rb_next(p); ...} 10000 skbs in 541846 ns (54 ns per skb)
method_3:rbtree_postorder_for_each_entry_safe() 10000 skbs in 868307 ns (86 ns per skb)
method_1:while (rb_first()) rb_erase() 99996 skbs in 7804021 ns (78 ns per skb)
method_2:rb_first; while (p) { p = rb_next(p); ...} 100000 skbs in 5942456 ns (59 ns per skb)
method_3:rbtree_postorder_for_each_entry_safe() 100000 skbs in 11584940 ns (115 ns per skb)
method_1:while (rb_first()) rb_erase() 1000000 skbs in 108577838 ns (108 ns per skb)
method_2:rb_first; while (p) { p = rb_next(p); ...} 1000000 skbs in 82619635 ns (82 ns per skb)
method_3:rbtree_postorder_for_each_entry_safe() 1000000 skbs in 127328743 ns (127 ns per skb)
Method 2) is simply faster, probably because it maintains a smaller
working size set.
Note that this is the method we use in tcp_ofo_queue() already.
I will also change skb_rbtree_purge() in a second patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it seems no need to keep tun_get() and __tun_get() at same time.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
reset the driver's DCB state in couple of places
where it was missing.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Farrington says:
====================
liquidio: firmware loading
1. Allow host driver parameter to override auto-loaded firmware (in flash).
2. Verify version of firmware that is auto-loaded from flash.
3. Change value of fw_type module parameter to reflect default firmware
image name that is loaded by host driver (in /sys/module/liquidio/...)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: port enabling
This patchset makes slave open and close symmetrical and provides
helpers for enabling or disabling a given DSA port.
Changes in v3:
- save the phy_device change for a future patchset
Changes in v2:
- do not remove the phy argument from port enable/disable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide dsa_port_enable and dsa_port_disable helpers to respectively
enable and disable a switch port. This makes the dsa_port_set_state_now
helper static.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA slave open function configures the unicast MAC addresses on the
master device, enable the switch port, change its STP state, then start
the PHY device.
Make the close function symmetric, by first stopping the PHY device,
then changing the STP state, disabling the switch port and restore the
master device.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For older hosts without multi-channel (vRSS) support, and some error
cases, we still need to set the real number of queues to one.
This patch adds this missing setting.
Fixes: 8195b1396e ("hv_netvsc: fix deadlock on hotplug")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petar Penkov says:
====================
net: Improve code coverage of syzkaller
This patch series is intended to improve code coverage of syzkaller on
the early receive path, specifically including flow dissector, GRO,
and GRO with frags parts of the networking stack. Syzkaller exercises
the stack through the TUN driver and this is therefore where changes
reside. Current coverage through netif_receive_skb() is limited as it
does not touch on any of the aforementioned code paths. Furthermore,
for full coverage, it is necessary to have more flexibility over the
linear and non-linear data of the skbs.
The following patches address this by providing the user(syzkaller)
with the ability to send via napi_gro_receive() and napi_gro_frags().
Additionally, syzkaller can specify how many fragments there are and
how much data per fragment there is. This is done by exploiting the
convenient structure of iovecs. Finally, this patch series adds
support for exercising the flow dissector during fuzzing.
The code path including napi_gro_receive() can be enabled via the
IFF_NAPI flag. The remainder of the changes in this patch series give
the user significantly more control over packets entering the kernel.
To avoid potential security vulnerabilities, hide the ability to send
custom skbs and the flow dissector code paths behind a
capable(CAP_NET_ADMIN) check to require special user privileges.
Changes since v2 based on feedback from Willem de Bruijn and Mahesh
Bandewar:
Patch 1/ No changes.
Patch 2/ Check if the preconditions for IFF_NAPI_FRAGS (IFF_NAPI and
IFF_TAP) are met before opening/attaching rather than after.
If they are not, change the behavior from discarding the
flag to rejecting the command with EINVAL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a TUN/TAP receive mode that exercises the napi_gro_frags()
interface. This mode is available only in TAP mode, as the interface
expects packets with Ethernet headers.
Furthermore, packets follow the layout of the iovec_iter that was
received. The first iovec is the linear data, and every one after the
first is a fragment. If there are more fragments than the max number,
drop the packet. Additionally, invoke eth_get_headlen() to exercise flow
dissector code and to verify that the header resides in the linear data.
The napi_gro_frags() mode requires setting the IFF_NAPI_FRAGS option.
This is imposed because this mode is intended for testing via tools like
syzkaller and packetdrill, and the increased flexibility it provides can
introduce security vulnerabilities. This flag is accepted only if the
device is in TAP mode and has the IFF_NAPI flag set as well. This is
done because both of these are explicit requirements for correct
operation in this mode.
Signed-off-by: Petar Penkov <peterpenkov96@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: davem@davemloft.net
Cc: ppenkov@stanford.edu
Acked-by: Mahesh Bandewar <maheshb@google,com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes TUN driver to use napi_gro_receive() upon receiving packets
rather than netif_rx_ni(). Adds flag IFF_NAPI that enables these
changes and operation is not affected if the flag is disabled. SKBs
are constructed upon packet arrival and are queued to be processed
later.
The new path was evaluated with a benchmark with the following setup:
Open two tap devices and a receiver thread that reads in a loop for
each device. Start one sender thread and pin all threads to different
CPUs. Send 1M minimum UDP packets to each device and measure sending
time for each of the sending methods:
napi_gro_receive(): 4.90s
netif_rx_ni(): 4.90s
netif_receive_skb(): 7.20s
Signed-off-by: Petar Penkov <peterpenkov96@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: davem@davemloft.net
Cc: ppenkov@stanford.edu
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two drivers (dummy and ifb) call ether_setup(), after commit
61e84623ac ("net: centralize net_device min/max MTU checking"), the
range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
These two devices should not have limits on MTU. This patch set their
min_mtu/max_mtu to 0. So that dev_set_mtu() will not check the mtu range,
and can be set with any value.
CC: Eric Dumazet <edumazet@google.com>
CC: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
