This patch changes the code to only manage the PCIe gphy power for
CPMU-less devices only. The CPMU takes over management for newer
chips.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy test register location has been repurposed for 5717+ devices.
This patch changes the code to avoid this location for these devices.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a TG3_FLG3_5717_PLUS flag to collectively describe
the set of changes in the ASIC that will apply to all future chip
revisions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSS flag needs to be turned off during tg3_close(). If the device
fails to allocate more than one MSI-X vector the next time the device is
brought up, transmits will fail.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 commit e712699734 entitled
"tg3: Preserve PCIe MPS setting for new devs" attempted to ensure the
PCIe link negotiated Maximum Payload Size (MPS) setting was 128 bytes
for all devices that didn't support higher speeds. The 5784 device was
mistakenly added to this list when it shouldn't have. This patch
removes the 5784 ASIC rev devices from that list.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use skb->len for accounting as xt_quota does. Since nf_conntrack works
at the network layer, skb_network_offset should always returns ZERO.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The tuple got from unique_tuple() doesn't need to be really unique, so the
check for the unique tuple isn't necessary, when there isn't any other
choice. Eliminating the unnecessary nf_nat_used_tuple() can save some CPU
cycles too.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The only user of unique_tuple() get_unique_tuple() doesn't care about the
return value of unique_tuple(), so make unique_tuple() return void (nothing).
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This removes duplicate code by providing a default implementation
which is used by 3 of the 4 modules that provide these call.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>
IPVS was merged into the kernel quite a long time ago and
has been seeing wide-spread production use for even longer.
It seems appropriate for it to be no longer tagged as EXPERIMENTAL
Signed-off-as: Simon Horman <horms@verge.net.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>
some users of nf_ct_ext_exist() know ct->ext isn't NULL. For these users, the
check for ct->ext isn't necessary, the function __nf_ct_ext_exist() can be
used instead.
the type of the return value of nf_ct_ext_exist() is changed to bool.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
We currently disable BH for the whole duration of get_counters()
On machines with a lot of cpus and large tables, this might be too long.
We can disable preemption during the whole function, and disable BH only
while fetching counters for the current cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
If user misconfigures ingress and causes a redirection loop, don't
overwhelm the log. This is also a error case so make it unlikely.
Found by inspection, luckily not in real system.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The other calls to kmalloc in the same function use GFP_ATOMIC, and indeed
two locks are held within the body of the function.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ identifier f; @@
*f(...,GFP_ATOMIC,...)
... when != spin_unlock(...)
when != read_unlock(...)
when != write_unlock(...)
when != read_unlock_irq(...)
when != write_unlock_irq(...)
when != read_unlock_irqrestore(...)
when != write_unlock_irqrestore(...)
when != spin_unlock_irq(...)
when != spin_unlock_irqrestore(...)
*f(...,GFP_KERNEL,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
GET_STATS request uses the same memory region as the response.
If a new request for get stats is fired before the response for
the previous get_stats request is received, the response will
corrupt the new request, causing the f/w to misbehave.
Signed-off-by: Somnath K <somnathk@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
link status is wrongly displayed under certain circumstances.
This change fixes it.
Signed-off-by: Somnath K <somnathk@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when the BE device becomes unresponsive, dump the registers to help debugging
Signed-off-by: Somnath K <somnathk@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move be_check_sriov_fn_type to appropriate place to correctly determine
if the be2net driver needs to work as a VF driver or a PF driver.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix selected style problems reported by checkpatch.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC modules control registers vary as per the version of the
EMAC module. EMAC_CTRL_EWCTL,EMAC_CTRL_EWINTTCNT are available
only on EMAC_VERSION_1. The emac_dump_regs() function accesses
these indiscriminately. This patch fixes the issue.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of NAPI poll function in the driver does not service
Rx packets, error condition even if a single Tx packet gets serviced in
the napi poll call. This behavior severely affects performance for specific use
cases. This patch modifies the poll function implementation to service tx/rx
packets in an identical manner.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DaVinci EMAC module includes an interrupt pacing block that can
be programmed to throttle the rate at which interrupts are
generated. This patch implements interrupt pacing logic that can
be controlled through the ethtool interface(only rx_coalesce_usecs
param is honored)
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently you cannot disable multicast snooping while a device is
down. There is no good reason for this restriction and this patch
removes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were two problems here. We returned success if dnet_mii_init()
failed and there was a release_mem_region() missing.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using module options arp monitoring and balance-alb/balance-tlb
are mutually exclusive options. Anytime balance-alb/balance-tlb are
enabled mii monitoring is forced to 100ms if not set. When configuring
via sysfs no checking is currently done.
Handling these cases with sysfs has to be done a bit differently because
we do not have all configuration information available at once. This
patch will not allow a mode change to balance-alb/balance-tlb if
arp_interval is already non-zero. It will also not allow the user to
set a non-zero arp_interval value if the mode is already set to
balance-alb/balance-tlb. They are still mutually exclusive on a
first-come, first serve basis.
Tested with initscripts on Fedora and manual setting via sysfs.
Signed-off-by: Andy Gospodarek <gospo@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_fmt, pr_<level> and netdev_<level> where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ks8842 uses dma channel functions, so it should depend on DMA_ENGINE.
ERROR: "__dma_request_channel" [drivers/net/ks8842.ko] undefined!
ERROR: "dma_release_channel" [drivers/net/ks8842.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a fix for UCC device number in verbose debug message.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, only ethtool can get accurate link state of a tap device.
With this patch, IFF_RUNNING and IF_OPER_UP/DOWN are kept up to date as
well.
Signed-off-by: Nolan Leake <nolan@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some features require knowing the DTIM period
before associating. This implements the ability
to wait for a beacon in mac80211 before assoc
to provide this value. It is optional since
most likely not all drivers will need this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix possible double priv->mutex lock introduced by commit
a69b03e941
"iwlwifi: cancel scan watchdog in iwl_bg_abort_scan" .
We can not call cancel_delayed_work_sync(&priv->scan_check) with
priv->mutex locked because workqueue function iwl_bg_scan_check()
take that lock internally.
We do not need to synchronize when canceling priv->scan_check work.
We can avoid races (sending double abort command or send no
command at all) using STATUS_SCAN_ABORT bit. Moreover
current iwl_bg_scan_check() code seems to be broken, as
we should not send abort commands when currently aborting.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 8366 AP support in particular is still rather incomplete, but
this is unlikely to be addressed any time soon.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the information available through ethtool...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
This makes the information available through ethtool...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
For some drivers it can be useful to know whether the channel they're
supposed to switch to is going to be used for short off-channel work or
scanning, or whether the hardware is expected to stay on it for a while
longer. This is important for various kinds of calibration work, which
takes longer to complete and should keep some persistent state, even if
the channel temporarily changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts this commit. While in theory the change is
correct the patch does not address current assumptions made
by some drivers, one which is definitley affected is ath9k.
Prior to this change the scan complete callback would be
called after we returned to the home channel and configured
the hardware RX filters. After this change we call the scan
complete callback prior to both the hw config and the config
filter. At least for ath9k this breaks quite a few assumptions
on the callback, leading to disconnects to the AP after every scan
making the driver pretty useless on STA mode. The goal behind
this commit was to address the now understood spurious warnings
from ath9k and mac80211_hwsim on scanning on two wiphys at the
same time but we have now supressed these and will address this
issue in the next kernel release.
When fixing this for good next we must first review the other
driver's dependence on this logic and perhaps consider removal
of the scan complete callback all together.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issuing two consecutive scans you could often end up
getting in the logs:
"ath9k: Two wiphys trying to scan at the same time"
This message is due to a race in mac80211 but addressing
that race requires some more major changes on the driver
and perhaps optimizations on mac80211 like removing the
scan complete callback alltogether. Its too late to address
this this kernel release so supress the complaint and annotate
this needs fixing for later.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases there could be possible dereferencing freed pointer. The
update is intended to avoid this issue.
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of errors during message composing msg should be freed after canceling.
Signed-off-by: Yuri Kululin <ext-yuri.kululin@nokia.com>
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
