With the PMB enabled, only P1SEG and up are covered by the PMB mappings,
meaning that situations where out-of-bounds physical addresses are read
from will lead to TLB reset after the PMB miss, allowing for use cases
like dd if=/dev/mem to reset the TLB.
Fix this up to make sure the reference is between __MEMORY_START (phys)
and __pa(high_memory). This is coherent across all variants of sh/sh64
with and without MMU, though the PMB bug itself is only applicable to
SH-4A parts.
Reported-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When I used SuperH on-chip USB, there was the problem that accessed
r8a66597_root_hub which was not allocated.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes sci type of SH7723 from PORT_SCI to PORT_SCIFA.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7723 has SCIFA. This module is similer SCI register map, but it has FIFO.
So this patch adds new type(PORT_SCIFA) and change some type checking.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This removes the acpi_irq_balance_set() interface from the PCI
interrupt link driver.
x86 used acpi_irq_balance_set() to tell the PCI interrupt link
driver to configure links to minimize IRQ sharing. But the link
driver can easily figure out whether to turn on IRQ balancing
based on the IRQ model (PIC/IOAPIC/etc), so we can get rid of
that external interface.
It's better for the driver to figure this out at init-time. If
we set it externally via the x86 code, the interface reduces
modularity, and we depend on the fact that acpi_process_madt()
happens before we process the kernel command line.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Lifebook S6420 is the ICH9M-based follow-up to the S6410. The application panel
contains the following keys: lock, mobility center, eco, info.
Whilst key 4 might be more appropriate for help then key 2, I've done things the
S6410 way. I can confirm that backlight control is functional, and that the lock key
activates the Gnome screensaver as expected.
Signed-off-by: Tony Vroon <tony@linx.net>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>
If the initialization of a special QP (e.g. AQP1) fails due to a
software timeout, we have to remove the reference to that special QP
struct from the port struct to stop the driver from accessing the QP,
since it will be/has been destroyed by the caller, eg in this case
ib_mad.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Disabling gpe might interfere with gpe detection/handling,
thus producing "interrupt not handled" errors.
Ironically, disabling of GPE from interrupt context is already
under spinlock, so only userspace needs to start using it.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Restart current transaction if we recieved unexpected GPEs instead
of needed ones.
http://bugzilla.kernel.org/show_bug.cgi?id=11896
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a possibility that EC might break if next command is
issued within 1 us after write or burst-disable command.
Suggestd-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure we can tell if the GPE storm workaround gets activated,
and avoid flooding the logs afterwards.
http://bugzilla.kernel.org/show_bug.cgi?id=11841
"plenty of line "ACPI: EC: non-query interrupt received,
switching to interrupt mode" in dmesg"
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently acpi_run_osc() checks all the bits in _OSC result code (the
first DWORD in the capabilities buffer) to see error condition. But the
bit 0, which doesn't indicate any error, must be ignored.
The bit 0 is used as the query flag at _OSC invocation time. Some
platforms clear it during _OSC evaluation, but the others don't. On
latter platforms, current acpi_run_osc() mis-detects error when _OSC is
evaluated with query flag set because it doesn't ignore the bit 0.
Because of this, the __acpi_query_osc() always fails on such platforms.
And this is the cause of the problem that pci_osc_control_set() doesn't
work since the commit 4e39432f4d which
changed pci_osc_control_set() to use __acpi_query_osc().
Tested-by:"Tomasz Czernecki <czernecki@gmail.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The current dummy read references the wrong address allowing the next
descriptor address update to linger in the store buffer and get passed
by an 'append' event.
This issue was uncovered by the change from strongly-ordered to device
memory for the adma registers.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Impact: enable/disable ring buffer recording API added
Several kernel developers have requested that there be a way to stop
recording into the ring buffers with a simple switch that can also
be enabled from userspace. This patch addes a new kernel API to the
ring buffers called:
tracing_on()
tracing_off()
When tracing_off() is called, all ring buffers will not be able to record
into their buffers.
tracing_on() will enable the ring buffers again.
These two act like an on/off switch. That is, there is no counting of the
number of times tracing_off or tracing_on has been called.
A new file is added to the debugfs/tracing directory called
tracing_on
This allows for userspace applications to also flip the switch.
echo 0 > debugfs/tracing/tracing_on
disables the tracing.
echo 1 > /debugfs/tracing/tracing_on
enables it.
Note, this does not disable or enable any tracers. It only sets or clears
a flag that needs to be set in order for the ring buffers to write to
their buffers. It is a global flag, and affects all ring buffers.
The buffers start out with tracing_on enabled.
There are now three flags that control recording into the buffers:
tracing_on: which affects all ring buffer tracers.
buffer->record_disabled: which affects an allocated buffer, which may be set
if an anomaly is detected, and tracing is disabled.
cpu_buffer->record_disabled: which is set by tracing_stop() or if an
anomaly is detected. tracing_start can not reenable this if
an anomaly occurred.
The userspace debugfs/tracing/tracing_enabled is implemented with
tracing_stop() but the user space code can not enable it if the kernel
called tracing_stop().
Userspace can enable the tracing_on even if the kernel disabled it.
It is just a switch used to stop tracing if a condition was hit.
tracing_on is not for protecting critical areas in the kernel nor is
it for stopping tracing if an anomaly occurred. This is because userspace
can reenable it at any time.
Side effect: With this patch, I discovered a dead variable in ftrace.c
called tracing_on. This patch removes it.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
In the case of !CONFIG_SMP, raw_spinlock_t is empty and the spinlock functions
don't build. Fix by defining spinlock functions for the uniprocessor case.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is a potential issue that, when guest using pagetable without vmexit when
EPT enabled, guest would use PAT/PCD/PWT bits to index PAT msr for it's memory,
which would be inconsistent with host side and would cause host MCE due to
inconsistent cache attribute.
The patch set IGMT bit in EPT entry to ignore guest PAT and use WB as default
memory type to protect host (notice that all memory mapped by KVM should be WB).
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
WARNING: arch/x86/kernel/built-in.o(.text+0x1722c): Section mismatch
in reference from the function kvm_setup_secondary_clock() to the
function .devinit.text:setup_secondary_APIC_clock()
The function kvm_setup_secondary_clock() references
the function __devinit setup_secondary_APIC_clock().
This is often because kvm_setup_secondary_clock lacks a __devinit
annotation or the annotation of setup_secondary_APIC_clock is wrong.
Signed-off-by: Md.Rakib H. Mullick <rakib.mullick@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: handle HRTIMER_CB_IRQSAFE_UNLOCKED correctly from softirq context
nohz: disable tick_nohz_kick_tick() for now
irq: call __irq_enter() before calling the tick_idle_check
x86: HPET: enter hpet_interrupt_handler with interrupts disabled
x86: HPET: read from HPET_Tn_CMP() not HPET_T0_CMP
x86: HPET: convert WARN_ON to WARN_ON_ONCE
Before a vcpu blocks, it should switch to the guest signal mask to allow
signals to unblock it.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The page fault path can use two rmap_desc structures, if:
- walk_addr's dirty pte update allocates one rmap_desc.
- mmu_lock is dropped, sptes are zapped resulting in rmap_desc being
freed.
- fetch->mmu_set_spte allocates another rmap_desc.
Increase to 4 for safety.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: release buddies on yield
fix for account_group_exec_runtime(), make sure ->signal can't be freed under rq->lock
sched: clean up debug info
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ring-buffer: prevent infinite looping on time stamping
ftrace: disable tracing on resize
ftrace: fix breakage in bin_fmt results
ftrace: ftrace.txt version update
ftrace: update txt document
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
[XFS] XFS: Check for valid transaction headers in recovery
[XFS] handle memory allocation failures during log initialisation
[XFS] Account for allocated blocks when expanding directories
[XFS] Wait for all I/O on truncate to zero file size
[XFS] Fix use-after-free with log and quotas
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (21 commits)
ocfs2: Check search result in ocfs2_xattr_block_get()
ocfs2: fix printk related build warnings in xattr.c
ocfs2: truncate outstanding block after direct io failure
ocfs2/xattr: Proper hash collision handle in bucket division
ocfs2: return 0 in page_mkwrite to let VFS retry.
ocfs2: Set journal descriptor to NULL after journal shutdown
ocfs2: Fix check of return value of ocfs2_start_trans() in xattr.c.
ocfs2: Let inode be really deleted when ocfs2_mknod_locked() fails
ocfs2: Fix checking of return value of new_inode()
ocfs2: Fix check of return value of ocfs2_start_trans()
ocfs2: Fix some typos in xattr annotations.
ocfs2: Remove unused ocfs2_restore_xattr_block().
ocfs2: Don't repeat ocfs2_xattr_block_find()
ocfs2: Specify appropriate journal access for new xattr buckets.
ocfs2: Check errors from ocfs2_xattr_update_xattr_search()
ocfs2: Don't return -EFAULT from a corrupt xattr entry.
ocfs2: Check xattr block signatures properly.
ocfs2: add handler_map array bounds checking
ocfs2: remove duplicate definition in xattr
ocfs2: fix function declaration and definition in xattr
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (35 commits)
V4L/DVB (9516): cx18: Move DVB buffer transfer handling from irq handler to work_queue
V4L/DVB (9557): gspca: Small changes for the sensor HV7131B in zc3xx.
V4L/DVB (9556): gspca: Bad init sequence for sensor HV7131B in zc3xx.
V4L/DVB (9549): gspca: Fix a typo in one of gspca chips name.
V4L/DVB (9515): cx18: Use correct Mailbox IRQ Ack values and misc IRQ handling cleanup
V4L/DVB (9493): kconfig patch
V4L/DVB (9527): af9015: fix compile warnings
V4L/DVB (9524): af9013: fix bug in status reading
V4L/DVB (9511): cx18: Mark CX18_CPU_DE_RELEASE_MDL as a slow API call
V4L/DVB (9510): cx18: Fix write retries for registers that always change - part 2.
V4L/DVB (9506): ivtv/cx18: fix test whether modules should be loaded or not.
V4L/DVB (9499): cx88-mpeg: final fix for analogue only compilation + de-alloc fix
V4L/DVB (9496): cx88-blackbird: bugfix: cx88-blackbird-mpeg-users
V4L/DVB (9495): cx88-blackbird: bugfix: cx88-blackbird-poll-fix
V4L/DVB (9494): anysee: initialize anysee_usb_mutex statically
V4L/DVB (9492): unplug oops from dvb_frontend_init...
V4L/DVB (9486): ivtv/ivtvfb: no longer experimental
V4L/DVB (9485): ivtv: remove incorrect V4L1 & tvaudio dependency
V4L/DVB (9482): Documentation, especially regarding audio and informational links
V4L/DVB (9475): cx18: Disable write retries for registers that always change - part 1.
...
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Move legacy breadcrumb out of the reserved status page area
drm/i915: Filter pci devices based on PCI_CLASS_DISPLAY_VGA
drm/radeon: map registers at load time
drm: Remove infrastructure for supporting i915's vblank swapping.
i915: Remove racy delayed vblank swap ioctl.
i915: Don't whine when pci_enable_msi() fails.
i915: Don't attempt to short-circuit object_wait_rendering by checking domains.
i915: Clean up sarea pointers on leavevt
i915: Save/restore MCHBAR_RENDER_STANDBY on GM965/GM45
