Some gigabytes have on-board SIMG5723s connected to JMB ahcis. These
are used to implement hardware raid. Unfortunately some firmware
revisions on these 5723s don't bring the link down when all the
downstream ports are unoccupied while not responding to reset protocol
which makes libata think that there's device attached to the port but
is not responding and retry. This results in painfully wrong boot
detection time for these ports when they're empty.
This patch quirks those boards such that ahci gives up after the
initial timeout. Combined with parallel probing, this gives quick
enough probing and also is safe because SIMG5723 will respond to the
first try if any of the downstream ports is occupied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marc Bowes <marcbowes@gmail.com>
Reported-by: Nicolas Mailhot <Nicolas.Mailhot@LaPoste.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Too strong words led to spurious bug reports: Novell bugzilla #527748,
RedHat bugzilla #468800. This patch is used to soften up the dmesg on
SB600 PMP softreset failure recovery, so as to remove the scariness and
concern from community.
Reported-by: pgnet Dev <pgnet.dev@gmail.com>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add device IDS for Ibex Peak SATA AHCI Controllers
Signed-off-by: Jaroslav Kysela <jkysela@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add device ID for Intel 82801JI SATA AHCI controller.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Community reported one SB600 SATA issue(BZ #9412), which led to 64 bit
DMA disablement for all SB600 revisions by driver maintainers with
commits c7a42156d9 and
4cde32fc4b.
But the root cause is ASUS M2A-VM system BIOS bug in old revisions
like 0901, while forcing into 32bit DMA happens to work as workaround.
Now it's time to withdraw 4cde32fc4b
so as to restore the SB600 SATA 64bit DMA capability.
This patch is also adding the workaround for M2A-VM old BIOS revisions,
but users are suggested to upgrade their system BIOS to the latest one
if they meet this issue.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make the following EM related cleanups.
* Use msleep(1) instead of udelay(100) and reduce retry count to 5.
* s/MAX_SLOTS/EM_MAX_SLOTS/, s/MAX_RETRY/EM_MAX_RETRY/
* Make EM constants enums as suggested by Jeff.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Harddisks on HP dv[4-6] and HDX18 fail to come online after resume on
earlier BIOSen. Fortunately, HP recently released BIOS updates for
all machines to fix the issue. Detect old BIOSen, warn the user to
update BIOS on boot and suspend attempts and fail suspend.
Kudos to all the bug reporters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: kernel.org@epperson.homelinux.net
Cc: emisca@gmail.com
Cc: Gadi Cohen <dragon@wastelands.net>
Cc: Paul Swanson <paul@procursa.com>
Cc: s@ourada.org
Cc: Trevor Davenport <trevor.davenport@gmail.com>
Cc: corruptor1972 <steven_tierney@yahoo.co.uk>
Cc: Victoria Wilson <mail@vwilson.co.uk>
Cc: khiraly <khiraly.list@gmail.com>
Cc: Sean <wollombi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Along with MCP65, MCP67 and 73 also don't set CAP_NCQ. Force it.
Reported by zaceni@yandex.ru on bko#13014 and confirmed by Peer Chen.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: NightFox <zaceni2@yandex.ru>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During driver initialization ahci_start_port may not be able
to turn LEDs off because the hardware may still be transmitting
a message. And since the BIOS may not be setting the LEDs to
off the drive LEDs may end up in a fault state. This has
been seen on ICH9r and ICH10r when configured in AHCI mode
instead of RAID mode, this patch doesn't key off a specific
set of device IDs but will give the EM transmit bit a chance
to clear if busy.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ahci_transmit_led_message saves off the led_state
with a value that includes the port number OR'd
in, this incorrect value maybe reported back
in ahci_led_store.
For instance, if you turn off all the leds for
port 1 and cat the value back it will report 1
instead of 0.
# echo 0 > /sys/class/scsi_host/host1/em_message
# cat /sys/class/scsi_host/host1/em_message
1
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Blacklist HP Compaq 6720s so that it doesn't play a "spin down,
spin up, spin down" ping-pong with the hard disk during system
power off.
Signed-off-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no need to turn off intx explicitly on msi enable. This is
automatically handled by pci. Drop it.
This might be needed on machines if the BIOS turns intx off during
boot. However, there's no evidence of such behavior for ahci and
the only such case seems to be ICH5 PATA according to ata_piix.
Also, given the way ahci operates, it's highly unlikely BIOS ever
disables IRQ for the controller. However, as this change has slight
possibility of introducing failure, please schedule it for #upstream.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Added the Device IDs for MCP89 AHCI controller.
Removed the IDs of MCP7B because this chipset had been cancelled.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The SSS flag, which directs the OS to spin up one disk at a time
to not have the PSU blow out, sometimes gets set even when not needed.
The effect of this is a longer-than-needed boot time.
This patch adds a module parameter that makes the driver ignore SSS
at least as far as the parallel scan during boot is concerned...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP nx6310 that uses the AHCI driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a per host flag that allows drivers to opt in into
having its busses scanned in parallel.
Drivers that do not set this flag get their ports scanned in
the "original" sequence.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is an issue in ATI SB600/SB700 SATA that PxSERR.E should not be
set on some conditions, which will lead to many SATA ODD error messages.
commit 55a61604cd is the workaround.
Since SB800 fixed this HW issue, IGN_SERR_INTERNAL should be withdrawn
for SB800.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The present AHCI driver seems to support SATA GEN 3 speed, but the related
messages should be modified.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There currently are the following looping constructs.
* __ata_port_for_each_link() for all available links
* ata_port_for_each_link() for edge links
* ata_link_for_each_dev() for all devices
* ata_link_for_each_dev_reverse() for all devices in reverse order
Now there's a need for looping construct which is similar to
__ata_port_for_each_link() but iterates over PMP links before the host
link. Instead of adding another one with long name, do the following
cleanup.
* Implement and export ata_link_next() and ata_dev_next() which take
@mode parameter and can be used to build custom loop.
* Implement ata_for_each_link() and ata_for_each_dev() which take
looping mode explicitly.
The following iteration modes are implemented.
* ATA_LITER_EDGE : loop over edge links
* ATA_LITER_HOST_FIRST : loop over all links, host link first
* ATA_LITER_PMP_FIRST : loop over all links, PMP links first
* ATA_DITER_ENABLED : loop over enabled devices
* ATA_DITER_ENABLED_REVERSE : loop over enabled devices in reverse order
* ATA_DITER_ALL : loop over all devices
* ATA_DITER_ALL_REVERSE : loop over all devices in reverse order
This change removes exlicit device enabledness checks from many loops
and makes it clear which ones are iterated over in which direction.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add an appropriate entry for the Promise PDC42819 controller. It has an
AHCI mode and so far works correctly with board_ahci.
This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port)
software-based RAID cards (for which there is a binary driver, t3sas) and
can be found on some motherboards, for example the MSI K9A2 Platinum,
which calls the chip a Promise T3 controller.
Although this controller also supports SAS devices, its default bootup mode
is AHCI and the binary driver has to do some magic to get the chip into the
appropriate mode to drive SAS disks.
Seeing as no documentation is provided by Promise, adding this entry to the
ahci driver allows the controller to be useful to people as a SATA
controller (with no ill effects on the system if a SAS disk is connected -
probing of the port just times out with "link online but device
misclassified"), without having to resort to using the binary driver. Users
who require SAS or the proprietary software raid can get this functionality
using the binary driver.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link. However, that assumption won't hold anymore with the scheduled
addition of slave link.
Make SCR access ops per-link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Marvell ahcis don't play nicely with PMPs. Disable it.
Reported by KueiHuan Chen in the following thread.
http://thread.gmane.org/gmane.linux.ide/33296
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: KueiHuan Chen <kueihuan.chen@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I've been chasing Jeff about this for months. Jeff added the Marvell
device identifiers to the ahci driver without making the AHCI driver
handle the PATA port. This means a lot of users can't use current
kernels and in most distro cases can't even install.
This has been going on since March 2008 for the 6121 Marvell, and late 2007
for the 6145!!!
This was all pointed out at the time and repeatedly ignored. Bugs assigned
to Jeff about this are ignored also.
To quote Jeff in email
> "Just switch the order of 'ahci' and 'pata_marvell' in
> /etc/modprobe.conf, then use Fedora's tools regenerate the initrd.
> See? It's not rocket science, and the current configuration can be
> easily made to work for Fedora users."
(Which isn't trivial, isn't end user, shouldn't be needed, and as it usually
breaks at install time is in fact impossible)
To quote Jeff in August 2007
> " mv-ahci-pata
> Marvell 6121/6141 PATA support. Needs fixing in the 'PATA controller
> command' area before it is usable, and can go upstream."
Only he add the ids anyway later and caused regressions, adding a further
id in March causing more regresions.
The actual fix for the moment is very simple. If the user has included
the pata_marvell driver let it drive the ports. If they've only selected
for SATA support give them the AHCI driver which will run the port a fraction
faster. Allow the user to control this decision via ahci.marvell_enable as
a module parameter so that distributions can ship 'it works' defaults and
smarter users (or config tools) can then flip it over it desired.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SIS controllers were blacklisted for PMP as enabling it made device
detection fail whether the device was PMP or not - the natural
conclusion was the controller chokes on SRST w/ pmp==15. However, it
turned out that the controller just didn't like issuing SRST after
hardreset w/o clearing SError first. Interestingly, the SRST itself
succeeds but the following commands fail.
If SError is cleared between hardreset and SRST, which is the default
behavior now, everything works fine and SIS controllers work with PMPs
happily.
Remove PMP blacklisting for SIS AHCIs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Piter PUNK <piterpunk@slackware.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Resend with proper whitespace.
This patch adds the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The new type checking of the flags arguments to irqsave and friends
(commit 3f307891ce) pointed out this thing
with a big nice warning.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In an I/O heavy workload (IOZone), ahci_qc_issue is the second-highest
consumer of CPU cycles. Removing the flush gets us approximately 10%
bandwidth improvement. I believe this to be because the CPU can start
queueing the next request instead of waiting for the readl() to flush the
writes to the device. The flush isn't necessary because we're using a
'queue' metaphor; we don't guarantee the command has got to the device,
nor do we need to guarantee the command has got to the controller.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During resume, sleep 1 second to wait for the HBA reset
to finish is a waste of time.
According to the AHCI 1.2 spec,
We should poll the HOST_CTL register,
and return error if the host reset is not
finished within 1 second.
Test results show that the HBA reset can be done quickly(in usecs).
And this patch may save nearly 1 second during resume.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add Enclosure Management support to libata and ahci.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit ea0c62f7cf tried to clear all
bits in irq_stat but it didn't actually achieve that as irq_stat was
anded with port_map right after read. This patch makes ahci driver
always use the unmasked value to clear irq_status.
While at it, add explanation on the peculiarities of ahci IRQ
clearing.
This was spotted by Linus Torvalds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some AHCI controllers (ICH7 was reported) set pending bit in
HOST_IRQ_STAT for non-existent ports and when it's not cleared falls
into IRQ storm. Always clear full irq_stat instead of only the bits
that are handled. As nothing changes for recognized ports, the risk
of breaking things is pretty low.
Reported and verified by Philipp Thomas in the following suse
bugzilla.
https://bugzilla.novell.com/attachment.cgi?id=215692
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Philipp Thomas <pth@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
From: Piter PUNK <piterpunk@slackware.com>
SiS AHCIs say they can do PMP but can't and fail detection if SRST w/
pmp==15 is used. Turn off PMP support.
tj: added patch description, adapted patch to #upstream-fixes and
renamed board_ahci_sis to board_ahci_nopmp.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
JMB361 has only one port but reports it has two causing longish probe
failure on the second one. Quirk it.
Reported by Gajo Petrovic in bz 10911.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Gajo Petrovic <gajo01@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads
to soft reset failure. This patch can fix the bug.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability. Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c,
as the actual PCI IDs deployed in the field differed from the forecasted ones
preemptively placed in the driver.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some chips need AHCI_EN set more than once to actually set it. Try a
few times before giving up and spitting out WARN_ON().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, SATA softresets should do link onlineness check before
actually performing SRST protocol but it doesn't really belong to
softreset.
This patch moves onlineness check in softreset to ata_eh_reset() and
ata_eh_followup_srst_needed() to clean up code and help future sata_mv
changes which need clear separation between SCR and TF accesses.
sata_fsl is peculiar in that its softreset really isn't softreset but
combination of hardreset and softreset. This patch adds dummy private
->prereset to keep the current behavior but the driver really should
implement separate hard and soft resets and return -EAGAIN from
hardreset if it should be follwed by softreset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
