Bump up the driver version number to reflect the changes done to
work with vmxnet3 adapter version 2
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the driver understand adapter version 2.
Cc: Rachel Lunnon <rachel_lunnon@stormagic.com>
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rcd length was zero, the page used for frag was not being released. It
was being replaced with a newly allocated page. This change takes care
of that memory leak.
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a handler for pci shutdown so that the driver has an
opportunity to make sure that device is quiesced before the PCI
switches to legacy IRQs. This way the possibility of
"screaming interrupt" is avoided.
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows for packet parsing to be done by the fast path. This performance
optimization already exists for IPv4. Add similar logic for IPv6.
Signed-off-by: Amitabha Banerjee <banerjeea@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hex constant chosen for VMXNET3_REV1_MAGIC is offensive,
replace it with its decimal equivalent.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Reviewed-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gao Zhenyu <gzhenyu@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Reviewed-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failing to reinitialize on wakeup results in loss of network connectivity for
vmxnet3 interface.
Signed-off-by: Srividya Murali <smurali@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Reviewed-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx ring 2 size can be configured by adjusting rx-jumbo parameter
of ethtool -G.
Signed-off-by: Ramya Bolla <bollar@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.
It modifies drivers implementation of set/get_rxfh accordingly.
This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.
User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.
Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move PCI_VENDOR_ID_VMWARE from device-specific files to pci_ids.h.
It is useful to always have access to it, especially when accessing
subsystem_vendor_id on emulated devices.
[bhelgaas: keep pci_ids.h sorted and use lower-case hex]
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We should check if the map of the table actually succeeds, and also free
resources accordingly.
Version bumped to 1.2.1.0
Acked-by: Shelley Gong <shelleygong@vmware.com>
Acked-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ethtool is used to update ring sizes on a vmxnet3 interface that isn't
running, the change isn't stored, meaning the ring update is effectively is
ignored and lost without any indication to the user.
Other network drivers store the ring size update so that ring allocation uses
the new sizes next time the interface is brought up. This patch modifies
vmxnet3 to behave this way as well
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in vmnet3_tx_xmit which
can be called in hard irq and other contexts. vmnet3_tx_xmit only
frees skbs that it has dropped.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit d25f06ea46 "vmxnet3: fix netpoll race condition",
the vmxnet3 driver fails to build when CONFIG_PCI_MSI is disabled,
because it unconditionally references the vmxnet3_msix_rx()
function.
To fix this, use the same #ifdef in the caller that exists around
the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3's netpoll driver is incorrectly coded. It directly calls
vmxnet3_do_poll, which is the driver internal napi poll routine. As the netpoll
controller method doesn't block real napi polls in any way, there is a potential
for race conditions in which the netpoll controller method and the napi poll
method run concurrently. The result is data corruption causing panics such as this
one recently observed:
PID: 1371 TASK: ffff88023762caa0 CPU: 1 COMMAND: "rs:main Q:Reg"
#0 [ffff88023abd5780] machine_kexec at ffffffff81038f3b
#1 [ffff88023abd57e0] crash_kexec at ffffffff810c5d92
#2 [ffff88023abd58b0] oops_end at ffffffff8152b570
#3 [ffff88023abd58e0] die at ffffffff81010e0b
#4 [ffff88023abd5910] do_trap at ffffffff8152add4
#5 [ffff88023abd5970] do_invalid_op at ffffffff8100cf95
#6 [ffff88023abd5a10] invalid_op at ffffffff8100bf9b
[exception RIP: vmxnet3_rq_rx_complete+1968]
RIP: ffffffffa00f1e80 RSP: ffff88023abd5ac8 RFLAGS: 00010086
RAX: 0000000000000000 RBX: ffff88023b5dcee0 RCX: 00000000000000c0
RDX: 0000000000000000 RSI: 00000000000005f2 RDI: ffff88023b5dcee0
RBP: ffff88023abd5b48 R8: 0000000000000000 R9: ffff88023a3b6048
R10: 0000000000000000 R11: 0000000000000002 R12: ffff8802398d4cd8
R13: ffff88023af35140 R14: ffff88023b60c890 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff88023abd5b50] vmxnet3_do_poll at ffffffffa00f204a [vmxnet3]
#8 [ffff88023abd5b80] vmxnet3_netpoll at ffffffffa00f209c [vmxnet3]
#9 [ffff88023abd5ba0] netpoll_poll_dev at ffffffff81472bb7
The fix is to do as other drivers do, and have the poll controller call the top
half interrupt handler, which schedules a napi poll properly to recieve frames
Tested by myself, successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: stable@vger.kernel.org
Reviewed-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: pv-drivers@vmware.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This update cleans up the MSI-X/MSI enablement code, fixes
vmxnet3_acquire_msix_vectors() invalid return values and
enables a dead code in case VMXNET3_LINUX_MIN_MSIX_VECT
MSI-X vectors were allocated.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: pv-drivers@vmware.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent conversion to skb_set_hash() was incorrect. 'skb' is
uninitialized at this point.
Fixes: 0b68070347 ('net: vmxnet3 calls skb_set_hash')
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
This patch adds support for virtual IOMMU to the vmxnet3 module. We
switch to DMA consistent mappings for anything we pass to the device.
There were a few places where we already did this, but using pci_blah();
these have been fixed to use dma_blah(), along with all new occurrences
where we've replaced kmalloc() and friends.
Also fix two small bugs:
1) use after free of rq->buf_info in vmxnet3_rq_destroy()
2) a cpu_to_le32() that should have been a cpu_to_le64()
Acked-by: George Zhang <georgezhang@vmware.com>
Acked-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux is free to call ethtool ops as soon as a netdev exists when probe
finishes. However, we only allocate vmxnet3 tx/rx queues and initialize the
rx_buf_per_pkt field in struct vmxnet3_adapter when the interface is
opened (UP).
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed that vmxnet3's get_ringparam function was returning the summation of all
ring buffers on a NIC, rather than just the size of any one ring. This causes
problems when a vmxnet3 instance has multiple queues, as ethtool, when setting
ring parameters, first gets the current ring parameters to set the existing
values in the set_ringparm commannd. The result is, that unless both rx and tx
ring sizes are set in a single operation, which ever ring is not set will
silently have its ring count multiplied by the number of queues on the NIC until
it reaches a driver defined maxiumum value.
Fix it by not multiplying the rx and tx ring sizes by the number of queues in
the system, like every other driver. Tested by myself successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/ethtool.c
drivers/net/vmxnet3/vmxnet3_drv.c
drivers/net/wireless/iwlwifi/dvm/tx.c
net/ipv6/route.c
The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.
The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.
The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.
The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 fails to set netif_carrier_off on probe, meaning that when an interface
is opened the __LINK_STATE_NOCARRIER bit is already cleared, and so
/sys/class/net/<ifname>/operstate remains in the unknown state. Correct this by
setting netif_carrier_off on probe, like other drivers do.
Also, while we're at it, lets remove the netif_carrier_ok checks from the
link_state_update function, as that check is atomically contained within the
netif_carrier_[on|off] functions anyway
Tested successfully by myself
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VMXNET3 device provides RSS hash value for received packets,
but it is not being used.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than generating a different RSS key on each boot, just use
a predetermined value that will map same flow to same value on
every device for more predictable testing. This is already done
on most hardware drivers.
Initial key value just some arbitrary bits extracted once
from /dev/random.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This static variable is never set, it initializes to 0 which
is VMXNET3_INTR_BUDDYSHARE, and never changes.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An atomic counter of devices present is maintained but never used.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the standard netdev_xxx() and dev_xxx() wrappers to format
log messages.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_dbg() rather than dev_dbg() because the former prints
the device name which is more useful than the pci name.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This messages that occur during boot time from this device
when netdev_err is called before calling register_netdevice().
Switch to using dev_XXX macros which correlate message with PCI info which
is available.
Rather than fixing the features message, just remove it since
the information is redundant and available through ethtool.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The uncommitted[] array was set but never used except in a debug
message. Remove it.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_alloc_skb_align, rather than open code using dev_alloc_skb.
Change allocation at startup to use GFP_KERNEL.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: VMware, Inc. <pv-drivers@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 has a 16Kbytes limit per tx descriptor, that happened to work
as long as we provided PAGE_SIZE fragments.
Our stack can now build larger fragments, so we need to split them to
the 16kbytes boundary.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: jongman heo <jongman.heo@samsung.com>
Tested-by: jongman heo <jongman.heo@samsung.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_open() can complete before register_netdev() returns.
Fix vmxnet3_probe_device() to support this.
Signed-off-by: Steve Hodgson <steve@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix log messages and corrects some typos
Change logging of failure to enable MSI/MSI-X to display device's PCI
address instead of eth%d. Rectify a typo.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix transport header size
Fix the transpoert header size for UDP packets.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently shown that vmxnet3 devices on transmit, will drop very small udp
frames consistently. This is due to a regression introduced by commit
39d4a96fd7. This commit attempts to introduce an
optimization to the tx path, indicating that the underlying hardware behaves
optimally when at least 54 bytes of header data are available for direct access.
This causes problems however, if the entire frame is less than 54 bytes long.
The subsequent pskb_may_pull in vmxnet3_parse_and_copy_hdr fails, causing an
error return code, which leads to vmxnet3_tq_xmit dropping the frame.
Fix it by placing a cap on the copy length. For frames longer than 54 bytes, we
do the pull as we normally would. If the frame is shorter than that, copy the
whole frame, but no more. This ensures that we still get the optimization for
qualifying frames, but don't do any damange for frames that are too short.
Also, since I'm unable to do this, it wuold be great if vmware could follow up
this patch with some additional code commentary as to why 54 bytes is an optimal
pull length for a virtual NIC driver. The comment that introduced this was
vague on that. Thanks!
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Max Matveev <mmatveev@redhat.com>
CC: Max Matveev <mmatveev@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct spelling in "uncommited" to "uncommitted" in
drivers/net/vmxnet3/vmxnet3_drv.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use existing helpers to clarify skb headers manipulation.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All tables of function pointers should be const to make hacks
more difficult. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that support modification of the RX flow hash indirection
table initialise it in the same way: RX rings are assigned to table
entries in rotation. Make that default policy explicit by having them
call a ethtool_rxfh_indir_default() function.
In the ethtool core, add support for a zero size value for
ETHTOOL_SRXFHINDIR, which resets the table to this default.
Partly-suggested-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new ethtool operation (get_rxfh_indir_size) to get the
indirectional table size. Use this to validate the user buffer size
before calling get_rxfh_indir or set_rxfh_indir. Use get_rxnfc to get
the number of RX rings, and validate the contents of the new
indirection table before calling set_rxfh_indir. Remove this
validation from drivers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.
Add note that drivers must not use ethtool_rxnfc::rule_locs.
The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vmxnet3 driver enables vlan filters if filtering is enabled for
any vlan. In promiscuous mode the filter table is cleared to in
order to disable filtering. However, if a vlan device is subsequently
created that vlan will be added to the filter, re-engaging it. As a
result, not only do we not see all the vlans in promiscuous mode, we
don't even see vlans for which a filter was previously created.
CC: Scott J. Goldman <scottjg@vmware.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HIGHDMA is being disabled even when dma64 is true. This patch fixes it.
CC: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parent device for netdev should be set before netdev_info() can be called
otherwise there is a NULL pointer dereference and probe() fails.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>--
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 device supports only power-of-two number of queues. The driver
therefore needs to check this and rounds down the number of queues to the
nearest power of two.
Signed-off-by: Yong Wang <yongwang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
If the rx ring is completely empty, then the device may never fire an rx
interrupt. Unfortunately, the rx interrupt is what triggers populating the
rx ring with fresh buffers, so this will cause networking to lock up.
This patch replenishes the skb in recv descriptor as soon as it is
peeled off while processing rx completions. If the skb/buffer
allocation fails, existing one is recycled and the packet in hand is
dropped. This way none of the RX desc is ever left empty, thus avoiding
starvation
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving packets from another guest on the same hypervisor, it's
generally possible to receive large packets because no segmentation is
necessary and these packets are handled by LRO. However, when doing
routing or bridging we must disable LRO and lose this benefit. In
these cases GRO can still be used and it is very effective because the
packets which are segmented in the hypervisor are received very close
together and can easily be merged.
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: Scott Goldman <scottjg@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the vmxnet3 driver to use the new vlan model. In doing so
it fixes missing tags in tcpdump and failure to do checksum offload when
tx vlan offload is disabled.
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing some backporting I noticed that vmxnet3 had a variable that was set
but never used. Get rid of it, and stop the compiler from griping
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
Convert vmxnet3 driver to 64 bit statistics interface.
This driver was already counting packet per queue in a 64 bit value so not
a huge change. Eliminate unused old net_device_stats structure.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization of vmxnet3, the state of LRO
gets out of sync with netdev->features.
This leads to very poor TCP performance in a IP forwarding
setup and is hitting many VMware users.
Simplified call sequence:
1. vmxnet3_declare_features() initializes "adapter->lro" to true.
2. The kernel automatically disables LRO if IP forwarding is enabled,
so vmxnet3_set_flags() gets called. This also updates netdev->features.
3. Now vmxnet3_setup_driver_shared() is called. "adapter->lro" is still
set to true and LRO gets enabled again, even though
netdev->features shows it's disabled.
Fix it by updating "adapter->lro", too.
The private vmxnet3 adapter flags are scheduled for removal
in net-next, see commit a0d2730c95
"net: vmxnet3: convert to hw_features".
Patch applies to 2.6.37 / 2.6.38 and 2.6.39-rc6.
Please CC: comments.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resending this patch with few changes.
Avoid multiple queues when MSI or MSI-X not available
Limit number of Tx queues to 1 if MSI/MSI-X support is not configured in
the kernel. This will make number of tx and rx queues equal when MSI/X
is not configured thus providing better performance.
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
