The Coverity checker (CID: 659, 660) spotted this resource leak on
PCI probe error path. Free private data structure if pci_enable_device()
fails.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 58) spotted this duplicated idx != 0
validation for unicast keys in prism2_ioctl_siwencodeext().
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 452, 453, 454, 455, 456) spotted this
unlikely read overrun of CIS buffer. Abort if CISTPL_CONFIG or
CISTPL_MANFID would not fit in buffer.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 930) spotted this double free on error path
(allocation failure). Do not free these here since generic error path
will take care of this.
Signed-off-by: Eugene Teo <eugene.teo@eugeneteo.net>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 273) spotted this inconsequent NULL checking
(unconditionally dereferencing directly after checking for NULL
isn't a good idea). Return immediately to avoid this.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 59) noted that the call to prism2_hw_reset()
was dead code. Move prism2_hw_reset() call to a place where it is
actually executed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Observed problems when multiple processes request scans and subsequently
scan results. This causes a scan result request to hit card registers
before the scan is complete, returning an incomplete scan list and
possibly making the card very angry. Instead, cache the results of a
wireless scan and serve result requests from the cache, rather than
hitting the hardware for them.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number 2312 was used all over the place to refer to the card's
default MTU. Make it a #define and use that everywhere rather than the
number.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show the specific device that driver messages are about.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without the attached, the kernel complains about my BIOS' PNP tables. It
was ACKed before, but never merged:
http://marc.theaimsgroup.com/?l=linux-kernel&m=110237794007900&w=2
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes all occurances of _INLINE_ in the kernel.
With the exception of tty_flip.h, I've simply removed the inline's since
gcc should know best which functions to be inlined.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change driver to use kzalloc rather than kmalloc+memset
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert from semaphore to mutex.
Untested as I have no access to a floppy drive at the moment.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert to use mutex from a semaphore
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@suse.de>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since early 2.4.x all cdrom drivers implement the block_device methods
themselves, so they can handle additional ioctls directly instead of going
through the cdrom layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a small helper for each ioctl to cut down cdrom_ioctl to a readable
size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is unsafe to suspend devices if the hardware is controlled by X. Add an
extra check to prevent this from happening.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change all the Zoran (ZR36050/ZR36060) drivers to use i2c_master_send instead
of i2c_transfer when possible. This simplifies the code by a few lines in
each driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drop support for the ENCODER_DUMP command in the adv7175 driver. ENCODER_DUMP
was never actually defined as far as I can see, so the code was ifdef'd out,
and I suspect it was never used, not even once, as it includes an obvious
array overrun.
The register values of this specific chip can be dumped in a generic way using
the i2c-dev driver and the "i2cdump" user-space tool if it is ever really
needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drop the adv7175 register cache, as it is only written to and never read back
from. This saves 128 bytes of memory and slightly speeds up the register
writes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Semaphore to mutexes conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a (probably harmless) array overrun in the DECODER_DUMP command of the
saa7110 driver. No big deal as this command is not used anywhere anyway.
Also reformat the dump so that it displays nicely.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bt856 driver has a register cache much larger than needed. We really only
write to 3 registers, so a 32-byte cache is a bit too much. We can be just as
efficient with a 6-byte cache. We could even do with a 3-byte cache, but at
the cost of additional arithmetics arguably not worth the spared 3 bytes.
Also, 4 of the 6 other members of the bt856 data structure were not used
anywhere, so we can as well drop them for an additional 16 bytes of memory
spared.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When grabbing composite video with Iomega Buz, the stock driver will
prevent grabbing from the same input twice in a row, forcing the user to
switch inputs before anything useful can be grabbed again. It is caused by
some optimization code in the input selection parts, and triggered by the
saa7111_command() executing cmd 0. The attached patch will remedy this by
disabling cmd 0 altogether; a fix that has no found negative effects on the
rest of the code. In fact, saa7110.c does the exact same thing.
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cleanups to the zr36057 initialization:
* Drop intermediate local variables.
* Single error path.
Also drop a needless cast on kfree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Explicitely state the number of registers the SAA7111 has, and use that
defined value where relevant. This should prevent any future array overrun
like the one I just fixed in the saa7110 driver.
This patch also saves 8 bytes of memory as a side effect, as the register
cache was larger than needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the i2c block write mode of the saa7114 driver. A previous code change
accidentally commented out a local variable increment, which should have been
kept, causing the register writes over the I2C bus to never be batched,
replacing any attempted block write by slower, individual write transactions.
Also drop the commented out code, as it only adds to confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is version 20 of the Wireless Extensions. This is the
completion of the RtNetlink work I started early 2004, it enables the
full Wireless Extension API over RtNetlink.
Few comments on the patch :
o totally driver transparent, no change in drivers needed.
o iwevent were already RtNetlink based since they were created
(around 2.5.7). This adds all the regular SET and GET requests over
RtNetlink, using the exact same mechanism and data format as iwevents.
o This is a Kconfig option, as currently most people have no
need for it. Surprisingly, patch is actually small and well
encapsulated.
o Tested on SMP, attention as been paid to make it 64 bits clean.
o Code do probably too many checks and could be further
optimised, but better safe than sorry.
o RtNetlink based version of the Wireless Tools available on
my web page for people inclined to try out this stuff.
I would also like to thank Alexey Kuznetsov for his helpful
suggestions to make this patch better.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for new chip 5755 which is very similar to 5787.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the tx producer and consumer fields in separate cache lines in
the device structure, similar to the VJ net channel queue structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine two small (56 byte and 320 byte) pci consistent memory
allocations into one allocation. Jeff Garzik suggested to store
the combined size in the bp structure for later use when freeing
the memory.
Use kzalloc() instead of kmalloc() + memset().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some link-related problems by doing a coalesce_now after link
change interrupt to flush out the transient link status.
To facilitate this, the host coalesce cmd register value is cached in
the device structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
All callers of macio_register_driver() either ignore the return value or
return it as the return value of a module_init() function.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
Nobody uses the return value of of_register_driver() anyway.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
drivers/macintosh/via-pmu.c:164: warning: `sleep_in_progress' defined but not used
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup the use of i2c headers in macintosh drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now powerpc uses the generic RTC stuff we should not enable the old RTC.
Doing so will result in hangs at boot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerbook_sleep_grackle is only called inside via-pmu, from pmu_ioctl()
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the debug driver is built-in, link it in last, so that any real
drivers will probe first, rather than having the debug driver pick the
first scsi slots..
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Merge avlab serial board entries in parport_serial
[SERIAL] kernel console should send CRLF not LFCR
hi,
this fixes coverity bug #888, where the variable
dev is used uninitialized. I assume the programmer
meant to use mdev, which is initialized.
Compile tested only.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
this fixes coverity bug #912, where skb is freed first,
and dereferenced a few lines later with skb->len.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this patch is required to get a SIS964 based motherboard ethernet working (FSC D1875)
(picking the #1 transceiver, instead of the last one, in case no known ones were found
might be a better default, and would have worked in this case too)
Signed-off-by: Artur Skawina <art_k@o2.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[patch 4/6] s390: qeth :allow setting of attribute "route6" to "no_router".
From: Ursula Braun <braunu@de.ibm.com>
when setting route6 attribute back to no_router qeth does not
issue an IP ASSIST command to reset router value to no_router.
Once primary_router is set device stays in this mode.
Issue an IP ASSIST command when no_router is set in route6.
Device will be reset and thus will not longer run as a primary
router.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 5 -----
1 files changed, 5 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[patch 3/6] s390: qeth driver cleanups
From: Ursula Braun <braunu@de.ibm.com>
- code analyzing tool BEAM has found some unreachable
and unnecessary statements and also conditions
which are always true.
- removed some useless MII code since OSA card will never
allow to set such values.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 49 ++++---------------------------------------------
qeth_proc.c | 18 +++++++++---------
qeth_sys.c | 2 +-
3 files changed, 14 insertions(+), 55 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With Au1xx0 Ethernet driver, TX bytes/packets always remain zero. The
problem seems to be that when packet has been transmitted, the length word
in DMA buffer is zero.
The patch updates the TX stats when a buffer is fed to DMA. The initial
2.4 patch was posted to linux-mips@linux-mips.org by Thomas Lange 21 Jan
2005.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that libata is smart enought to handle both soft and hard resets,
add softreset method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Not much to say here except that some drives have fixed and bad firmware
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Add a secondary TSB for hugepage mappings.
[SPARC]: Respect vm_page_prot in io_remap_page_range().
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Bump driver version and reldate.
[TG3]: Skip phy power down on some devices
[TG3]: Fix SRAM access during tg3_init_one()
[X25]: dte facilities 32 64 ioctl conversion
[X25]: allow ITU-T DTE facilities for x25
[X25]: fix kernel error message 64 bit kernel
[X25]: ioctl conversion 32 bit user to 64 bit kernel
[NET]: socket timestamp 32 bit handler for 64 bit kernel
[NET]: allow 32 bit socket ioctl in 64 bit kernel
[BLUETOOTH]: Return negative error constant
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sg increments the refcount of constituent pages in its higher order memory
allocations when they are about to be mapped by userspace. This is done so
the subsequent get_page/put_page when doing the mapping and unmapping does not
free the page.
Move over to the preferred way, that is, using compound pages instead. This
fixes a whole class of possible obscure bugs where a get_user_pages on a
constituent page may outlast the user mappings or even the driver.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_NO_REAP is documented as an option that will cause this slab not to be
reaped under memory pressure. However, that is not what happens. The only
thing that SLAB_NO_REAP controls at the moment is the reclaim of the unused
slab elements that were allocated in batch in cache_reap(). Cache_reap()
is run every few seconds independently of memory pressure.
Could we remove the whole thing? Its only used by three slabs anyways and
I cannot find a reason for having this option.
There is an additional problem with SLAB_NO_REAP. If set then the recovery
of objects from alien caches is switched off. Objects not freed on the
same node where they were initially allocated will only be reused if a
certain amount of objects accumulates from one alien node (not very likely)
or if the cache is explicitly shrunk. (Strangely __cache_shrink does not
check for SLAB_NO_REAP)
Getting rid of SLAB_NO_REAP fixes the problems with alien cache freeing.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not use platform_device_register_simple() as it is going away, define
dcdbas_driver and implement ->probe() and ->remove() functions so manual
binding and unbinding will work with this driver.
Also switch to using attribute_group when creating sysfs attributes and
make sure to check and handle errors; explicitely remove attributes when
detaching driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not use platform_device_register_simple() as it is going away.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mv64x600_wdt: convert to the new platform device interface Do not use
platform_device_register_simple() as it is going away.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch does the following for v441xx seris drivers:
- stop using platform_device_register_simple() as it is going away
- mark ->probe() and ->remove() methods as __devinit and __devexit
respectively
- initialize "owner" field in driver structure so there is a link
from /sys/modules to the driver
- mark *_init() and *_exit() functions as __init and __exit
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update the serial_txx9 driver.
* More strict check in verify_port. Cleanup.
* Do not insert a char caused previous overrun.
* Fix some spin_locks.
* Do not call uart_add_one_port for absent ports.
Also, this patch removes a BROKEN tag from Kconfig. This driver has been
marked as BROKEN by removal of uart_register_port, but it has been solved
already on Sep 2005.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code that handles bios that span table target boundaries by breaking
them up into smaller bios will not split an individual struct bio_vec into
more than two pieces. Sometimes more than that are required.
This patch adds a loop to break the second piece up into as many pieces as
are necessary.
Cc: "Abhishek Gupta" <abhishekgupt@gmail.com>
Cc: Dan Smith <danms@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The console cursor can be called in atomic context. Change memory
allocation to use the GFP_ATOMIC flag in i810fb_cursor().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some PHYs should not be powered down in tg3_set_power_state() because
of bugs or other hardware limitations.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5700 and 5701 will not return correct SRAM data when the chip is in
D3hot power state. tg3_get_eeprom_hw_cfg() must first put the device
in D0 before reading SRAM.
Thanks to Thomas Chenault at Dell for noticing this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan noted: "bmdma may be zero but the bmdma_irq_clear function gets
called even in this case during pure PIO operation. Check we have a
bmdma before we use it."
I fixed this by adding a check for zero. While was I there, I fixed the
non-standard indentation of the small function's code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The first performs the simplex clearing relevant to some chipsets that
report simplex by default but can in fact do more if poked. The second
is used to strip DMA modes from a PCI control with no BAR4 allocation.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch addresses a number of weird behaviours observed
for the sata_mv driver, by fixing an "off by one" bug in processing
of the EDMA response queue.
Basically, sata_mv was looking in the wrong place for
command results, and this produced a lot of unpredictable behaviour.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Encapsulate some of ata_scsi_slave_config so that parts
can be reused in future SAS patches.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add some dummy noop functions for use by libata clients
that do not need to do anything. Future SAS patches will
utilize these functions.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Original patch (and description) by Douglas Gilbert, with minor fixes
and API updates from me.
Changelog:
- make existing libata VPD device identification page (0x83)
supply the ATA serial number in the libata "vendor
specific" designator (from Chris Paulson-Ellis)
- add a "t10 vendor id based" designator as defined in
SAT rev 08 (section 10.3.4.2.3) that supplies ATA
model and serial numbers
- make the libata VPD page 0x83 more extensible (for
adding more designators in the future).
- rename EVPD to VPD in various places. Enable Vital
Product Data (EVPD) is a bit in the INQUIRY cdb.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64-SGI] SN2-XP reduce kmalloc wrapper inlining
[IA64] MCA: remove obsolete ifdef
[IA64] MCA: update MCA comm field for user space tasks
[IA64] MCA: print messages in MCA handler
[IA64-SGI] - Eliminate SN pio_phys_xxx macros. Move to assembly
[IA64] use icc defined constant
[IA64] add __builtin_trap definition for icc build
[IA64] clean up asm/intel_intrin.h
[IA64] map ia64_hint definition to intel compiler intrinsic
[IA64] hooks to wait for mmio writes to drain when migrating processes
[IA64-SGI] driver bugfixes and hardware workarounds for CE1.0 asic
[IA64-SGI] Handle SC env. powerdown events
[IA64] Delete MCA/INIT sigdelayed code
[IA64-SGI] sem2mutex ioc4.c
[IA64] implement ia64 specific mutex primitives
[IA64] Fix UP build with BSP removal support.
[IA64] support for cpu0 removal
This reverts commit 08f1d0b99f
The "bt8xx/ conversion" for drivers/video/ hasn't actually percolated
all the way to this tree, so the Makefile change escaped too soon.
Build breakage noticed by Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lennert Buytenhek
Move the uengine loader from arch/arm/mach-ixp2000 to arch/arm/common
so that ixp23xx can use it too.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- undo some Lindent damage by indenting member names
- remove history at top of .c file, this is stored in the kernel
repo changelog (in greater detail, even).
drivers/net/skfp/fplustm.c: In function `enable_formac':
drivers/net/skfp/fplustm.c:552: warning: large integer implicitly truncated to unsigned type
drivers/net/skfp/fplustm.c:555: warning: large integer implicitly truncated to unsigned type
These arguments were changed to `const', so the compiler can now see that it's
doing and outw(..., 0xffffnnnn). Cast the arg to ushort.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All accessor's different methods are now selected with C code and unused
ones statically optimized away at compile time instead of being selected
with #if's and #ifdef's. This has many advantages such as allowing the
compiler to validate the syntax of the whole code, making it cleaner and
easier to understand, and ultimately allowing people to define
configuration symbols in terms of variables if they really want to
dynamically support multiple bus configurations at the same time (with
the unavoidable performance cost).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Boards with multiple PHYs were not being handled properly by the pcnet32
driver. This patch by Thomas Bogendoerfer with changes by me will allow
Allied Telesyn 2700FTX and 2701FTX boards to use either the copper or
the fiber interfaces. It has been tested on ia32 and ppc64 hardware.
Philippe Seewer also tested and improved the patch.
ethtool for pcnet32 already supports multiple phys.
See also bugzilla bug 4219.
Please apply to 2.6.16
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hardware has additional error trap interrupt bits. I have never seen
them trigger, but if they do, it looks like this might be useful.
Signed-off-by: Stephen Hemminger <shemminger@osdl.rog>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch decodes state and revovers from any races in the transmit
timeout and NAPI logic. It should never trigger, but if it does then
do the right thing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change default coalescing parameters slightly, and allow wider
range of values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Redo the interupt handling of sky2 driver based on the IRQ mangement
documentation. All interrupts are handled by the device0 NAPI poll
routine.
Don't need to adjust interrupt mask in IRQ context, done only when
changing device under RTNL. Therefore don't need hwlock anymore.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove wake on lan support for now. It doesn't work right, and I
don't have a machine with working suspend/resume to test or fix it.
It will be re-enabled later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon EC/rev0 (A1) chipset requires a bunch of workarounds. I copied these
from sk98lin. But since they never got tested and add more cruft to the code;
any attempt at using driver as is on this version will probably fail.
It looks like this was a early engineering sample chip revision, if it ever shows
up on a real system. Produce an error message.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When I/O is non-cache-coherent, we need to ensure that the I/O buffers
we use don't share cache lines with other data.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reformat some code to make it easier to read. And whitespace
fixes.
Signed-off-by: Stephen Hemminger <sheminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add mmio barriers at the appropriate places, don't have a platform
that needs them, but this is where the documentation of the patch
says to add them.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup of the part of the code that sets up DMA configuration.
Should cause no real change in operation, just clearer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SysKonnect Genesis and Yukon chip sets have restrictions on the possible
control block area. The memory needs to not cross 4 Gig boundary, and it needs
to be 8 byte aligned. This patch checks and fails to bring the device up
if region is unacceptable.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve performance of skge driver by not touching irq mask
register as much. Since the interrupt source auto-masks, the driver
can just leave it disabled until the end of the soft irq.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup transmit buffers using NAPI. This allows the transmit routine
to leave interrupts enabled, and that improves performance.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SCSI midlayer has moved hostt->eh_timed_out to transport template. As
libata doesn't need full-blown transport support yet, implement
minimal transport for libata. No transport class or whatsoever, just
empty transport template with ->eh_timed_out hook.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[CRYPTO] aes: Fixed array boundary violation
[CRYPTO] tcrypt: Fix key alignment
[CRYPTO] all: Add missing cra_alignmask
[CRYPTO] all: Use kzalloc where possible
[CRYPTO] api: Align tfm context as wide as possible
[CRYPTO] twofish: Use rol32/ror32 where appropriate
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (23 commits)
[PATCH] sysfs: fix a kobject leak in sysfs_add_link on the error path
[PATCH] sysfs: don't export dir symbols
[PATCH] get_cpu_sysdev() signedness fix
[PATCH] kobject_add_dir
[PATCH] debugfs: Add debugfs_create_blob() helper for exporting binary data
[PATCH] sysfs: fix problem with duplicate sysfs directories and files
[PATCH] Kobject: kobject.h: fix a typo
[PATCH] Kobject: provide better warning messages when people do stupid things
[PATCH] Driver core: add macros notice(), dev_notice()
[PATCH] firmware: fix BUG: in fw_realloc_buffer
[PATCH] sysfs: kzalloc conversion
[PATCH] fix module sysfs files reference counting
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE() to USB subsystem
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE() to RCU subsystem
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE()
[PATCH] Clean up module.c symbol searching logic
[PATCH] kobj_map semaphore to mutex conversion
[PATCH] kref: avoid an atomic operation in kref_put()
[PATCH] handle errors returned by platform_get_irq*()
[PATCH] driver core: platform_get_irq*(): return -ENXIO on error
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
README: bzip2 is not new
Documentation/Changes: remove outdated translation references
remove dead Radeon URL
SCSI_AACRAID: add a help text
update the i386 defconfig
MAINTAINERS: remove the LANMEDIA entry
Move ip2.c and ip2main.c to drivers/char/ip2/ where the other files
